Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: The objective of this work is to explicit knowledge on the interactions between the chlorophyll-a and nine meroplankton larvae of epibenthonic fauna. The studied case is the Arraial do Cabo upwelling system, Southeastern of Brazil, which provides different environmental conditions. To assess this information a network approach based in probability estimative was used. Comparisons among the generated graphs are made in the light of different water masses, application of Shannon biodiversity index, and the closeness and betweenness centralities measurements. Our results show the main pattern among different water masses and how the core organisms belonging to the network skeleton are correlated to the main environmental variable. We conclude that the approach of complex networks is a promising tool for environmental diagnostic.
Abstract: The hidden-point bar method is useful in many
surveying applications. The method involves determining the
coordinates of a hidden point as a function of horizontal and vertical
angles measured to three fixed points on the bar. Using these
measurements, the procedure involves calculating the slant angles,
the distances from the station to the fixed points, the coordinates of
the fixed points, and then the coordinates of the hidden point. The
propagation of the measurement errors in this complex process has
not been fully investigated in the literature. This paper evaluates the
effect of the bar geometry on the position accuracy of the hidden
point which depends on the measurement errors of the horizontal and
vertical angles. The results are used to establish some guidelines
regarding the inclination angle of the bar and the location of the
observed points that provide the best accuracy.
Abstract: Currently, many types of no-reversible compressed
sound source, represented by MP3 (MPEG Audio Layer-3) are
popular in the world and they are widely used to make the music file
size smaller. The sound data created in this way has less information as
compared to pre-compressed data. The objective of this study is by
analyzing EEG to determine if people can recognize such difference as
differences in sound. A measurement system that can measure and
analyze EEG when a subject listens to music were experimentally
developed. And ten subjects were studied with this system. In this
experiment, a WAVE formatted music data and a MP3 compressed
music data that is made from the WAVE formatted data were
prepared. Each subject was made to hear these music sources at the
same volume. From the results of this experiment, clear differences
were confirmed between two wound sources.
Abstract: Applying a rigorous process to optimize the elements
of a supply-chain network resulted in reduction of the waiting time
for a service provider and customer. Different sources of downtime
of hydraulic pressure controller/calibrator (HPC) were causing
interruptions in the operations. The process examined all the issues to
drive greater efficiencies. The issues included inherent design issues
with HPC pump, contamination of the HPC with impurities, and the
lead time required for annual calibration in the USA.
HPC is used for mandatory testing/verification of formation
tester/pressure measurement/logging-while drilling tools by oilfield
service providers, including Halliburton.
After market study andanalysis, it was concluded that the current
HPC model is best suited in the oilfield industry. To use theexisting
HPC model effectively, design andcontamination issues were
addressed through design and process improvements. An optimum
network is proposed after comparing different supply-chain models
for calibration lead-time reduction.
Abstract: Partial Discharge measurement is a very important
means of assessing the integrity of insulation systems in a High
Voltage apparatus. In compressed gas insulation systems, floating
particles can initiate partial discharge activities which adversely
affect the working of insulation. Partial Discharges below the
inception voltage also plays a crucial in damaging the integrity of
insulation over a period of time. This paper discusses the effect of
loose and fixed Copper and Nichrome wire particles on the PD
characteristics in SF6-N2 (10:90) gas mixtures at a pressure of
0.4MPa. The Partial Discharge statistical parameters and their
correlation to the observed results are discussed.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: Knowledge about the magnetic quantities in a magnetic circuit is always of great interest. On the one hand, this information is needed for the simulation of a transformer. On the other hand, parameter studies are more reliable, if the magnetic quantities are derived from a well established model. One possibility to model the 3-phase transformer is by using a magnetic equivalent circuit (MEC). Though this is a well known system, it is often not an easy task to set up such a model for a large number of lumped elements which additionally includes the nonlinear characteristic of the magnetic material. Here we show the setup of a solver for a MEC and the results of the calculation in comparison to measurements taken. The equations of the MEC are based on a rearranged system of the nodal analysis. Thus it is possible to achieve a minimum number of equations, and a clear and simple structure. Hence, it is uncomplicated in its handling and it supports the iteration process. Additional helpful tasks are implemented within the solver to enhance the performance. The electric circuit is described by an electric equivalent circuit (EEC). Our results for the 3-phase transformer demonstrate the computational efficiency of the solver, and show the benefit of the application of a MEC.
Abstract: Switched-mode converters play now a significant role in
modern society. Their operation are often crucial in various electrical
applications affecting the every day life. Therefore, the quality of
the converters needs to be reliably verified. Recent studies have
shown that the converters can be fully characterized by a set of
frequency responses which can be efficiently used to validate the
proper operation of the converters. Consequently, several methods
have been proposed to measure the frequency responses fast and
accurately. Most often correlation-based techniques have been applied.
The presented measurement methods are highly sensitive to
external errors and system nonlinearities. This fact has been often
forgotten and the necessary uncertainty analysis of the measured
responses has been neglected. This paper presents a simple approach
to analyze the noise and nonlinearities in the frequency-response
measurements of switched-mode converters. Coherence analysis is
applied to form a confidence interval characterizing the noise and
nonlinearities involved in the measurements. The presented method is
verified by practical measurements from a high-frequency switchedmode
converter.
Abstract: The main focus of this paper is on the human induced
forces. Almost all existing force models for this type of load (defined
either in the time or frequency domain) are developed from the
assumption of perfect periodicity of the force and are based on force
measurements conducted on rigid (i.e. high frequency) surfaces. To
verify the different authors conclusions the vertical pressure
measurements invoked during the walking was performed, using
pressure gauges in various configurations. The obtained forces are
analyzed using Fourier transformation. This load is often decisive in
the design of footbridges. Design criteria and load models proposed
by widely used standards and other researchers were introduced and a
comparison was made.
Abstract: Nylon 6-clay hybrid/neat nylon 6, sheath/core
bicomponent nanocomposite fibers containing 4 wt% of clay in
sheath section were melt spun at different take-up speeds. Their
orientation and crystalline structure were compared to those of neat
nylon 6 fibers. Birefringence measurements showed that the
orientation development in sheath and core parts of bicomponent
fibers was different. Crystallinity results showed that clay did not act
as a nucleating agent for bicomponent fibers. The neat nylon 6 fiber
had a smooth surface while striped pattern was appeared on the
surface of bicomponent fiber containing clay due to thermal
shrinkage of the core part.
Abstract: This paper focuses on operational risk measurement
techniques and on economic capital estimation methods. A data
sample of operational losses provided by an anonymous Central
European bank is analyzed using several approaches. Loss
Distribution Approach and scenario analysis method are considered.
Custom plausible loss events defined in a particular scenario are
merged with the original data sample and their impact on capital
estimates and on the financial institution is evaluated. Two main
questions are assessed – What is the most appropriate statistical
method to measure and model operational loss data distribution? and
What is the impact of hypothetical plausible events on the financial
institution? The g&h distribution was evaluated to be the most
suitable one for operational risk modeling. The method based on the
combination of historical loss events modeling and scenario analysis
provides reasonable capital estimates and allows for the measurement
of the impact of extreme events on banking operations.
Abstract: In this work, we try to find the best setting
of Computational Fluid Dynamic solver available for the problems in
the field of supersonic internal flows. We used the supersonic air-toair
ejector to represent the typical problem in focus. There are
multiple oblique shock waves, shear layers, boundary layers
and normal shock interacting in the supersonic ejector making this
device typical in field of supersonic inner flows. Modeling of shocks
in general is demanding on the physical model of fluid, because
ordinary conservation equation does not conform to real conditions in
the near-shock region as found in many works. From these reasons,
we decided to take special care about solver setting in this article by
means of experimental approach of color Schlieren pictures and
pneumatic measurement. Fast pressure transducers were used to
measure unsteady static pressure in regimes with normal shock in
mixing chamber. Physical behavior of ejector in several regimes is
discussed. Best choice of eddy-viscosity setting is discussed on the
theoretical base. The final verification of the k-ω SST is done on the
base of comparison between experiment and numerical results.
Abstract: Wind is among the potential energy resources which
can be harnessed to generate wind energy for conversion into
electrical power. Due to the variability of wind speed with time and
height, it becomes difficult to predict the generated wind energy more
optimally. In this paper, an attempt is made to establish a
probabilistic model fitting the wind speed data recorded at
Makambako site in Tanzania. Wind speeds and direction were
respectively measured using anemometer (type AN1) and wind Vane
(type WD1) both supplied by Delta-T-Devices at a measurement
height of 2 m. Wind speeds were then extrapolated for the height of
10 m using power law equation with an exponent of 0.47. Data were
analysed using MINITAB statistical software to show the variability
of wind speeds with time and height, and to determine the underlying
probability model of the extrapolated wind speed data. The results
show that wind speeds at Makambako site vary cyclically over time;
and they conform to the Weibull probability distribution. From these
results, Weibull probability density function can be used to predict
the wind energy.
Abstract: Single crystals of Magnesium alloys such as Mg-1Al,
Mg-1Zn-0.5Y, Mg-3Li, and AZ31 alloys were successfully fabricated in this study by employing the modified Bridgman method. Single
crystals of pure Mg were also made in this study. To determine the exact orientation of crystals, Laue back-reflection method and pole figure measurement were carried out on each single crystal. Dimensions of single crystals were 10 mm in diameter and 120 mm in
length. Hardness and compression tests were conducted and the results
revealed that hardness and the strength strongly depended on the
orientation. The closer to basal one the orientation was, the higher hardness and compressive strength were. The effect of alloying was
not higher than that of orientation. After compressive deformation of single crystals, the orientation of the crystals was found to rotate and to be parallel to the basal orientation.
Abstract: The passive electrical properties of a tissue depends
on the intrinsic constituents and its structure, therefore by measuring
the complex electrical impedance of the tissue it might be possible to
obtain indicators of the tissue state or physiological activity [1].
Complete bio-impedance information relative to physiology and
pathology of a human body and functional states of the body tissue or
organs can be extracted by using a technique containing a fourelectrode
measurement setup. This work presents the estimation
measurement setup based on the four-electrode technique. First, the
complex impedance is estimated by three different estimation
techniques: Fourier, Sine Correlation and Digital De-convolution and
then estimation errors for the magnitude, phase, reactance and
resistance are calculated and analyzed for different levels of
disturbances in the observations. The absolute values of relative
errors are plotted and the graphical performance of each technique is
compared.
Abstract: Magnetic carbon nanotubes composites were obtained
by filling carbon nanotubes with paramagnetic iron oxide particles.
Detailed investigation of magnetic behaviour of resulting composites
was done at different temperatures. Measurements indicate that these
functionalized nanotubes are superparamagnetic at room temperature;
however, no superparamagnetism was observed at 125 K and 80 K.
The blocking temperature TB was estimated at 145 K. These magnetic
carbon nanotubes have the potential of being used in a wide range of
applications, in particular, the production of nanofluids, which can be
controlled and steered by appropriate magnetic fields.
Abstract: In this work, a characterization and modeling of
packet loss of a Voice over Internet Protocol (VoIP) communication
is developed. The distributions of the number of consecutive received
and lost packets (namely gap and burst) are modeled from the
transition probabilities of two-state and four-state model.
Measurements show that both models describe adequately the burst
distribution, but the decay of gap distribution for non-homogeneous
losses is better fit by the four-state model. The respective
probabilities of transition between states for each model were
estimated with a proposed algorithm from a set of monitored VoIP
calls in order to obtain representative minimum, maximum and
average values for both models.
Abstract: This paper discusses the implementation of the Kalman
Filter along with the Global Positioning System (GPS) for indoor
robot navigation. Two dimensional coordinates is used for the map
building, and refers to the global coordinate which is attached to the
reference landmark for position and direction information the robot
gets. The Discrete Kalman Filter is used to estimate the robot position,
project the estimated current state ahead in time through time update
and adjust the projected estimated state by an actual measurement at
that time via the measurement update. The navigation test has been
performed and has been found to be robust.
Abstract: An electrical apparatus for measuring moisture
content was developed by our laboratory and uses dependence of
electrical properties on water content in studied material. Error
analysis of the apparatus was run by measuring different volumes of
water in a simplified specimen, i.e. hollow plexiglass block, in order
to avoid as many side-effects as possible. Obtained data were
processed using both basic and advanced statistics and results were
compared with each other. The influence of water content on
accuracy of measured data was studied as well as the influence of
variation of apparatus' proper arrangement or factual methodics of its
usage. The overall coefficient of variation was 4%. There was no
trend found in results of error dependence on water content.
Comparison with current surveys led to a conclusion, that the studied
apparatus can be used for indirect measurement of water content in
porous materials, with expectable error and under known conditions.
Factual experiments with porous materials are not involved, but are
currently under investigation.