Abstract: The paper presents a numerical investigation on the
rapid gas decompression in pure nitrogen which is made by using the
one-dimensional (1D) and three-dimensional (3D) mathematical
models of transient compressible non-isothermal fluid flow in pipes.
A 1D transient mathematical model of compressible thermal multicomponent
fluid mixture flow in pipes is presented. The set of the
mass, momentum and enthalpy conservation equations for gas phase
is solved in the model. Thermo-physical properties of multicomponent
gas mixture are calculated by solving the Equation of
State (EOS) model. The Soave-Redlich-Kwong (SRK-EOS) model is
chosen. This model is successfully validated on the experimental data
[1] and shows a good agreement with measurements. A 3D transient
mathematical model of compressible thermal single-component gas
flow in pipes, which is built by using the CFD Fluent code (ANSYS),
is presented in the paper. The set of unsteady Reynolds-averaged
conservation equations for gas phase is solved. Thermo-physical
properties of single-component gas are calculated by solving the Real
Gas Equation of State (EOS) model. The simplest case of gas
decompression in pure nitrogen is simulated using both 1D and 3D
models. The ability of both models to simulate the process of rapid
decompression with a high order of agreement with each other is
tested. Both, 1D and 3D numerical results show a good agreement
between each other. The numerical investigation shows that 3D CFD
model is very helpful in order to validate 1D simulation results if the
experimental data is absent or limited.
Abstract: Due to adverse pressure gradient along the diverging
walls of wide-angled diffusers, the attached flow separates from
one wall and remains attached permanently to the other wall in a
process called stalling. Stalled diffusers render the whole fluid flow
system, in which they are part of, very inefficient. There is then an
engineering need to try to understand the whole process of diffuser
stall if any meaningful attempts to improve on diffuser efficiency
are to be made. In this regard, this paper provides a data bank
contribution for the mean flow-field in wide-angled diffusers where
the complete velocity and static pressure fields, and pressure recovery
data for diffusers in the fully stalled flow regime are experimentally
measured. The measurements were carried out at Reynolds numbers
between 1.07×105 and 2.14×105 based on inlet hydraulic diameter
and centreline velocity for diffusers whose divergence angles were
between 30Ôùª and 50Ôùª. Variation of Reynolds number did not significantly
affect the velocity and static pressure profiles. The wall static
pressure recovery was found to be more sensitive to changes in the
Reynolds number. By increasing the velocity from 10 m/s to 20 m/s,
the wall static pressure recovery increased by 8.31%. However, as the
divergence angle was increased, a similar increase in the Reynolds
number resulted in a higher percentage increase in pressure recovery.
Experimental results showed that regardless of the wall to which
the flow was attached, both the velocity and pressure fields were
replicated with discrepancies below 2%.
Abstract: This article discusses the problem of estimating the
orientation of inclined ground on which a human subject stands based
on information provided by the vestibular system consisting of the
otolith and semicircular canals. It is assumed that body segments are
not necessarily aligned and thus forming an open kinematic chain.
The semicircular canals analogues to a technical gyrometer provide a
measure of the angular velocity whereas the otolith analogues to a
technical accelerometer provide a measure of the translational
acceleration. Two solutions are proposed and discussed. The first is
based on a stand-alone Kalman filter that optimally fuses the two
measurements based on their dynamic characteristics and their noise
properties. In this case, no body dynamic model is needed. In the
second solution, a central extended disturbance observer that
incorporates a body dynamic model (internal model) is employed.
The merits of both solutions are discussed and demonstrated by
experimental and simulation results.
Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.
Abstract: The aim of the study is to investigate a number of characteristics of Corporate Social Responsibility (CSR) indicators that should be adopted by CSR assessment methodologies. For the purpose of this paper, a survey among the Greek companies that belong to FTSE 20 in Athens Exchange (FTSE/Athex-20) has been conducted, as these companies are expected to pioneer in the field of CSR. The results show consensus as regards the characteristics of indicators such as the need for the adoption of general and specific sector indicators, financial and non-financial indicators, the origin and the weight rate. However, the results are contradictory concerning the appropriate number of indicators for the assessment of CSR and the unit of measurement. Finally, the company-s sector is a more important dimension of CSR than the size and the country where the company operates. The purpose of this paper is to standardize the main characteristics of CSR indicators.
Abstract: Subsonic wind tunnel experiments were conducted to
study the effect of tripped boundary layer on the pressure distribution
in the contraction region of the tunnel. Measurements were
performed by installing trip strip at two different positions in the
concave portion of the contraction. The results show that installation
of the trip strips, have significant effects on both turbulence and
pressure distribution. The reduction in the free stream turbulence and
reduction of the wall static pressure distribution deferred signified
with the location of the trip strip.
Abstract: BEAMnrc was used to calculate the spectrum and
HVL for X-ray Beam during low energy X-ray radiation using tube model: SRO 33/100 /ROT 350 Philips. The results of BEAMnrc
simulation and measurements were compared to the IPEM report
number 78 and SpekCalc software. Three energies 127, 103 and 84
Kv were used. In these simulation a tungsten anode with 1.2 mm for
Be window were used as source. HVLs were calculated from
BEAMnrc spectrum with air Kerma method for four different filters.
For BEAMnrc one billion particles were used as original particles for
all simulations. The results show that for 127 kV, there was
maximum 5.2 % difference between BEAMnrc and Measurements
and minimum was 0.7% .the maximum 9.1% difference between
BEAMnrc and IPEM and minimum was 2.3% .The maximum
difference was 3.2% between BEAMnrc and SpekCal and minimum
was 2.8%. The result show BEAMnrc was able to satisfactory predict
the quantities of Low energy Beam as well as high energy X-ray
radiation.
Abstract: This study aims to determine the level of resistance of Hevea brasiliensis and Paraserianthes falcataria (synonym: Falcataria molucana) against wood rot fungi Pleurotus ostreatus based on Indonesian standard SNI 01.7207-2006 and Japanese standard JIS K 1571-2004. The variables measured were visual appearance and weight loss percentage of wood based on longitudinal and cross section fiber directions of rubber wood and sengon wood. Measurement of oven dry weight loss of wood samples performed after 12 weeks incubation. Replication performed was 10 times at each treatment combination. The results based on SNI 01.7207-2006, weight loss value of H. brasiliensis and P. falcataria wood with fiber direction longitudinal were 23,12 and 22,25% respectively and cross section were 20,77 and 18,76% respectively, and all were classified to resistance class IV (no resistance). The results based on JIS K 1571-2004, weight loss value of both woods with fiber direction cross section were 10,95 and 14,20% respectively.
Abstract: The objective of this paper is to investigate a new
approach based on the idea of pictograms for food portion size. This
approach adopts the model of the United States Pharmacopeia- Drug
Information (USP-DI). The representation of each food portion size
composed of three parts: frame, the connotation of dietary portion
sizes and layout. To investigate users- comprehension based on this
approach, two experiments were conducted, included 122 Taiwanese
people, 60 male and 62 female with ages between 16 and 64 (divided
into age groups of 16-30, 31-45 and 46-64). In Experiment 1, the mean
correcting rate of the understanding level of food items is 48.54%
(S.D.= 95.08) and the mean response time 2.89sec (S.D.=2.14). The
difference on the correct rates for different age groups is significant
(P*=0.00
Abstract: In this paper as showed a non-invasive 3D eye tracker
for optometry clinical applications. Measurements of biomechanical
variables in clinical practice have many font of errors associated with
traditional procedments such cover test (CT), near point of
accommodation (NPC), eye ductions (ED), eye vergences (EG) and,
eye versions (ES). Ocular motility should always be tested but all
evaluations have a subjective interpretations by practitioners, the
results is based in clinical experiences, repeatability and accuracy
don-t exist. Optometric-lab is a tool with 3 (tree) analogical video
cameras triggered and synchronized in one acquisition board AD.
The variables globe rotation angle and velocity can be quantified.
Data record frequency was performed with 27Hz, camera calibration
was performed in a know volume and image radial distortion
adjustments.
Abstract: The influence of lactulose and inulin on rheological
properties of fermented milk during storage was studied.Pasteurized
milk, freeze-dried starter culture Bb-12 (Bifidobacterium lactis, Chr.
Hansen, Denmark), inulin – RAFTILINE®HP (ORAFI, Belgium) and
syrup of lactulose (Duphalac®, the Netherlands) were used for
experiments. The fermentation process was realized at 37 oC for 16
hours and the storage of products was provided at 4 oC for 7 days.
Measurements were carried out by BROOKFIELD standard methods
and the flow curves were described by Herschel-Bulkley model.
The results of dispersion analysis have shown that both the
concentration of prebiotics (p=0.04
Abstract: The aim of this study was to establish the feasibility of a minute incremental exercise testing protocol in young asthma children. Twenty-two children with clinically diagnosed mild to moderate asthma volunteered to participate. The maximum incremental exercise test was performed using a cycle ergometer with an electromagnetic braking. A warm-up unloaded for 2 minutes then the workload was started at 40 watts for 2 minutes, and then stepwise increments of 8 watts per 2 minutes were applied. The pedaling frequency was set at 50 rpm. Ventilation and gas exchange were measured with a breath-by-breath automatic metabolic measurement system. Results showed that this test was well tolerated by all asthmatic children. Most of the children reached the VO2 plateau and satisfied the criteria for maximal respiratory exchange ratio of ≥ 1. This Study demonstrated that this testing protocol was suitable for young asthmatic children.
Abstract: In this research, Forming Limit Diagrams for supertension
sheet metals which are using in automobile industry have
been obtained. The exerted strains to sheet metals have been
measured with four different methods and the errors of each method
have also been represented. These methods have been compared with
together and the most efficient and economic way of extracting of the
exerted strains to sheet metals has been introduced. In this paper total
error and uncertainty of FLD extraction procedures have been
derived. Determination of the measurement uncertainty in extracting
of FLD has a great importance in design and analysis of the sheet
metal forming process.
Abstract: The growing outsourcing of logistics services
resulting from the ongoing current in firms of costs
reduction/increased efficiency means that it is becoming more and
more important for the companies doing the outsourcing to carry out
a proper evaluation.
The multiple definitions and measures of logistics service
performance found in research on the topic create a certain degree of
confusion and do not clear the way towards the proper measurement
of their performance. Do a model and a specific set of indicators exist
that can be considered appropriate for measuring the performance of
logistics services outsourcing in industrial environments? Are said
indicators in keeping with the objectives pursued by outsourcing? We
aim to answer these and other research questions in the study we have
initiated in the field within the framework of the international High
Performance Manufacturing (HPM) project of which this paper
forms part.
As the first stage of this research, this paper reviews articles
dealing with the topic published in the last 15 years with the aim of
detecting the models most used to make this measurement and
determining which performance indicators are proposed as part of
said models and which are most used. The first steps are also taken in
determining whether these indicators, financial and operational, cover
the aims that are being pursued when outsourcing logistics services.
The findings show there is a wide variety of both models and
indicators used. This would seem to testify to the need to continue
with our research in order to try to propose a model and a set of
indicators for measuring the performance of logistics services
outsourcing in industrial environments.
Abstract: Scale defects are common surface defects in hot steel rolling. The modelling of such defects is problematic and their causes are not straightforward. In this study, we investigated genetic algorithms in search for a mathematical solution to scale formation. For this research, a high-dimensional data set from hot steel rolling process was gathered. The synchronisation of the variables as well as the allocation of the measurements made on the steel strip were solved before the modelling phase.
Abstract: A major challenge in biomaterials research is the
regulation of protein adsorption which is a key factor for controlling
the subsequent cell adhesion at implant surfaces. The aim of the
present study was to control the adsorption of fibronectin (FN) and
the attachment of MG-63 osteoblasts with an electronic
nanostructure. Shallow doping line lattices with a period of 260 nm
were produced for this purpose by implantation of phosphorous in
silicon wafers. Protein coverage was determined after incubating the
substrate with FN by means of an immunostaining procedure and the
measurement of the fluorescence intensity with a TECAN analyzer.
We observed an increased amount of adsorbed FN on the
nanostructure compared to control substrates. MG-63 osteoblasts
were cultivated for 24h on FN-incubated substrates and their
morphology was assessed by SEM. Preferred orientation and
elongation of the cells in direction of the doping lattice lines was
observed on FN-coated nanostructures.
Abstract: This paper presents the investigation results of UV
measurement at different level of altitudes and the development of a
new portable instrument for measuring UV. The rapid growth of
industrial sectors in developing countries including Malaysia, brings
not only income to the nation, but also causes pollution in various
forms. Air pollution is one of the significant contributors to global
warming by depleting the Ozone layer, which would reduce the
filtration of UV rays. Long duration of exposure to high to UV rays
has many devastating health effects to mankind directly or indirectly
through destruction of the natural resources. This study aimed to
show correlation between UV and altitudes which indirectly can help
predict Ozone depletion. An instrument had been designed to
measure and monitors the level of UV. The instrument comprises of
two main blocks namely data logger and Graphic User Interface
(GUI). Three sensors were used in the data logger to detect changes
in the temperature, humidity and ultraviolet. The system has
undergone experimental measurement to capture data at two different
conditions; industrial area and high attitude area. The performance of
the instrument showed consistency in the data captured and the
results of the experiment drew a significantly high reading of UV at
high altitudes.
Abstract: Control of commutation of switched reluctance (SR)
motor has been an area of interest for researchers for sometime now
with mixed successes in addressing the inherent challenges. New
technologies, processing schemes and methods have been adopted to
make sensorless SR drive a reality. There are a number of
conceptual, offline, analytical and online solutions in literature that
have varying complexities and achieved equally varying degree of
robustness and accuracies depending on the method used to address
the challenges and the SR drive application. Magnetic coupling is
one such challenge when using active probing techniques to
determine rotor position of a SR motor from stator winding. This
paper studies the effect of back-of-core saturation on the detected
rotor position and presents results on measurement made on a 4-
phase SR motor. The results shows that even for a four phase motor
which is excited one phase at a time and using the electrically
opposite phase for active position probing, the back-of-core
saturation effects should not be ignored.
Abstract: The decision to recruit manpower in an organization
requires clear identification of the criteria (attributes) that distinguish
successful from unsuccessful performance. The choice of appropriate
attributes or criteria in different levels of hierarchy in an organization
is a multi-criteria decision problem and therefore multi-criteria
decision making (MCDM) techniques can be used for prioritization
of such attributes. Analytic Hierarchy Process (AHP) is one such
technique that is widely used for deciding among the complex criteria
structure in different levels. In real applications, conventional AHP
still cannot reflect the human thinking style as precise data
concerning human attributes are quite hard to be extracted. Fuzzy
logic offers a systematic base in dealing with situations, which are
ambiguous or not well defined. This study aims at defining a
methodology to improve the quality of prioritization of an
employee-s performance measurement attributes under fuzziness. To
do so, a methodology based on the Extent Fuzzy Analytic Hierarchy
Process is proposed. Within the model, four main attributes such as
Subject knowledge and achievements, Research aptitude, Personal
qualities and strengths and Management skills with their subattributes
are defined. The two approaches conventional AHP
approach and the Extent Fuzzy Analytic Hierarchy Process approach
have been compared on the same hierarchy structure and criteria set.
Abstract: Segmentation, filtering out of measurement errors and
identification of breakpoints are integral parts of any analysis of
microarray data for the detection of copy number variation (CNV).
Existing algorithms designed for these tasks have had some successes
in the past, but they tend to be O(N2) in either computation time or
memory requirement, or both, and the rapid advance of microarray
resolution has practically rendered such algorithms useless. Here we
propose an algorithm, SAD, that is much faster and much less thirsty
for memory – O(N) in both computation time and memory requirement
-- and offers higher accuracy. The two key ingredients of SAD are the
fundamental assumption in statistics that measurement errors are
normally distributed and the mathematical relation that the product of
two Gaussians is another Gaussian (function). We have produced a
computer program for analyzing CNV based on SAD. In addition to
being fast and small it offers two important features: quantitative
statistics for predictions and, with only two user-decided parameters,
ease of use. Its speed shows little dependence on genomic profile.
Running on an average modern computer, it completes CNV analyses
for a 262 thousand-probe array in ~1 second and a 1.8 million-probe
array in 9 seconds