Abstract: Overcurrent (OC) relays are the major protection
devices in a distribution system. The operating time of the OC relays
are to be coordinated properly to avoid the mal-operation of the
backup relays. The OC relay time coordination in ring fed
distribution networks is a highly constrained optimization problem
which can be stated as a linear programming problem (LPP). The
purpose is to find an optimum relay setting to minimize the time of
operation of relays and at the same time, to keep the relays properly
coordinated to avoid the mal-operation of relays.
This paper presents two phase simplex method for optimum time
coordination of OC relays. The method is based on the simplex
algorithm which is used to find optimum solution of LPP. The
method introduces artificial variables to get an initial basic feasible
solution (IBFS). Artificial variables are removed using iterative
process of first phase which minimizes the auxiliary objective
function. The second phase minimizes the original objective function
and gives the optimum time coordination of OC relays.
Abstract: The reduction in vehicle exhaust emissions achieved
in the last two decades is offset by the growth in traffic, as well as by
changes in the composition of emitted pollutants. The present
investigation illustrates the emissions of in-use gasoline and diesel
passenger cars using the official European driving cycle and the
ARTEMIS real-world driving cycle. It was observed that some of the
vehicles do not comply with the corresponding regulations.
Significant differences in emissions were observed between driving
cycles. Not all pollutants showed a tendency to decrease from Euro 3
to Euro 5.
Abstract: Antimicrobial resistant is becoming a major factor in
virtually all hospital acquired infection may soon untreatable is a
serious public health problem. These concerns have led to major
research effort to discover alternative strategies for the treatment of
bacterial infection. Nanobiotehnology is an upcoming and fast
developing field with potential application for human welfare. An
important area of nanotechnology for development of reliable and
environmental friendly process for synthesis of nanoscale particles
through biological systems In the present studies are reported on the
use of fungal strain Aspergillus species for the extracellular synthesis
of bionanoparticles from 1 mM silver nitrate (AgNO3) solution. The
report would be focused on the synthesis of metallic bionanoparticles
of silver using a reduction of aqueous Ag+ ion with the
culture supernatants of Microorganisms. The bio-reduction of the
Ag+ ions in the solution would be monitored in the aqueous
component and the spectrum of the solution would measure through
UV-visible spectrophotometer The bionanoscale particles were
further characterized by Atomic Force Microscopy (AFM), Fourier
Transform Infrared Spectroscopy (FTIR) and Thin layer
chromatography. The synthesized bionanoscale particle showed a
maximum absorption at 385 nm in the visible region. Atomic Force
Microscopy investigation of silver bionanoparticles identified that
they ranged in the size of 250 nm - 680 nm; the work analyzed the
antimicrobial efficacy of the silver bionanoparticles against various
multi drug resistant clinical isolates. The present Study would be
emphasizing on the applicability to synthesize the metallic
nanostructures and to understand the biochemical and molecular
mechanism of nanoparticles formation by the cell filtrate in order to
achieve better control over size and polydispersity of the
nanoparticles. This would help to develop nanomedicine against
various multi drug resistant human pathogens.
Abstract: Localized surface plasmon resonance (LSPR) is the
coherent oscillation of conductive electrons confined in noble
metallic nanoparticles excited by electromagnetic radiation, and
nanosphere lithography (NSL) is one of the cost-effective methods to
fabricate metal nanostructures for LSPR. NSL can be categorized
into two major groups: dispersed NSL and closely pack NSL. In
recent years, gold nanocrescents and gold nanoholes with vertical
sidewalls fabricated by dispersed NSL, and silver nanotriangles and
gold nanocaps on silica nanospheres fabricated by closely pack NSL,
have been reported for LSPR biosensing. This paper introduces
several novel gold nanostructures fabricated by NSL in LSPR
applications, including 3D nanostructures obtained by evaporating
gold obliquely on dispersed nanospheres, nanoholes with slant
sidewalls, and patchy nanoparticles on closely packed nanospheres,
all of which render satisfactory sensitivity for LSPR sensing. Since
the LSPR spectrum is very sensitive to the shape of the metal
nanostructures, formulas are derived and software is developed for
calculating the profiles of the obtainable metal nanostructures by
NSL, for different nanosphere masks with different fabrication
conditions. The simulated profiles coincide well with the profiles of
the fabricated gold nanostructures observed under scanning electron
microscope (SEM) and atomic force microscope (AFM), which
proves that the software is a useful tool for the process design of
different LSPR nanostructures.
Abstract: Importance of software quality is increasing leading to development of new sophisticated techniques, which can be used in constructing models for predicting quality attributes. One such technique is Artificial Neural Network (ANN). This paper examined the application of ANN for software quality prediction using Object- Oriented (OO) metrics. Quality estimation includes estimating maintainability of software. The dependent variable in our study was maintenance effort. The independent variables were principal components of eight OO metrics. The results showed that the Mean Absolute Relative Error (MARE) was 0.265 of ANN model. Thus we found that ANN method was useful in constructing software quality model.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.
Abstract: The problem of estimating time-varying regression is
inevitably concerned with the necessity to choose the appropriate
level of model volatility - ranging from the full stationarity of instant
regression models to their absolute independence of each other. In the
stationary case the number of regression coefficients to be estimated
equals that of regressors, whereas the absence of any smoothness
assumptions augments the dimension of the unknown vector by the
factor of the time-series length. The Akaike Information Criterion
is a commonly adopted means of adjusting a model to the given
data set within a succession of nested parametric model classes,
but its crucial restriction is that the classes are rigidly defined by
the growing integer-valued dimension of the unknown vector. To
make the Kullback information maximization principle underlying the
classical AIC applicable to the problem of time-varying regression
estimation, we extend it onto a wider class of data models in which
the dimension of the parameter is fixed, but the freedom of its values
is softly constrained by a family of continuously nested a priori
probability distributions.
Abstract: To evaluate genetic variation of wheat (Triticum
aestivum) affected by heat and drought stress on eight Australian
wheat genotypes that are parents of Doubled Haploid (HD) mapping
populations at the vegetative stage, the water stress experiment was
conducted at 65% field capacity in growth room. Heat stress
experiment was conducted in the research field under irrigation over
summer. Result show that water stress decreased dry shoot weight
and RWC but increased osmolarity and means of Fv/Fm values in all
varieties except for Krichauff. Krichauff and Kukri had the
maximum RWC under drought stress. Trident variety was shown
maximum WUE, osmolarity (610 mM/Kg), dry mater, quantum yield
and Fv/Fm 0.815 under water stress condition. However, the
recovery of quantum yield was apparent between 4 to 7 days after
stress in all varieties. Nevertheless, increase in water stress after that
lead to strong decrease in quantum yield. There was a genetic
variation for leaf pigments content among varieties under heat stress.
Heat stress decreased significantly the total chlorophyll content that
measured by SPAD. Krichauff had maximum value of Anthocyanin
content (2.978 A/g FW), chlorophyll a+b (2.001 mg/g FW) and
chlorophyll a (1.502 mg/g FW). Maximum value of chlorophyll b
(0.515 mg/g FW) and Carotenoids (0.234 mg/g FW) content
belonged to Kukri. The quantum yield of all varieties decreased
significantly, when the weather temperature increased from 28 ÔùªC to
36 ÔùªC during the 6 days. However, the recovery of quantum yield
was apparent after 8th day in all varieties. The maximum decrease
and recovery in quantum yield was observed in Krichauff. Drought
and heat tolerant and moderately tolerant wheat genotypes were
included Trident, Krichauff, Kukri and RAC875. Molineux, Berkut
and Excalibur were clustered into most sensitive and moderately
sensitive genotypes. Finally, the results show that there was a
significantly genetic variation among the eight varieties that were
studied under heat and water stress.
Abstract: The purpose of this paper is to perform a multidisciplinary design and analysis (MDA) of honeycomb panels used in the satellites structural design. All the analysis is based on clamped-free boundary conditions. In the present work, detailed finite element models for honeycomb panels are developed and analysed. Experimental tests were carried out on a honeycomb specimen of which the goal is to compare the previous modal analysis made by the finite element method as well as the existing equivalent approaches. The obtained results show a good agreement between the finite element analysis, equivalent and tests results; the difference in the first two frequencies is less than 4% and less than 10% for the third frequency. The results of the equivalent model presented in this analysis are obtained with a good accuracy. Moreover, investigations carried out in this research relate to the honeycomb plate modal analysis under several aspects including the structural geometrical variation by studying the various influences of the dimension parameters on the modal frequency, the variation of core and skin material of the honeycomb. The various results obtained in this paper are promising and show that the geometry parameters and the type of material have an effect on the value of the honeycomb plate modal frequency.
Abstract: The purpose of this study was to explore the
relationship between Burnout, Negative Affectivity, and
Organizational Citizenship Behavior (OCB) for social service
workers at two agencies serving homeless populations. Thirty two
subjects completed surveys. Significant correlations between major
variables and subscales were found.
Abstract: Nigeria is considered as one of the many countries in
sub-Saharan Africa with a weak economy and gross deficiencies in technology and engineering. Available data from international monitoring and regulatory organizations show that technology is pivotal to determining the economic strengths of nations all over the
world. Education is critical to technology acquisition, development,
dissemination and adaptation. Thus, this paper seeks to critically
assess and discuss issues and challenges facing technological
advancement in Nigeria, particularly in the education sector, and also
proffers solutions to resuscitate the Nigerian education system
towards achieving national technological and economic sustainability
such that Nigeria can compete favourably with other technologicallydriven
economies of the world in the not-too-distant future.
Abstract: This paper presents a useful sub-pixel image
registration method using line segments and a sub-pixel edge detector.
In this approach, straight line segments are first extracted from gray
images at the pixel level before applying the sub-pixel edge detector.
Next, all sub-pixel line edges are mapped onto the orientation-distance
parameter space to solve for line correspondence between images.
Finally, the registration parameters with sub-pixel accuracy are
analytically solved via two linear least-square problems. The present
approach can be applied to various fields where fast registration with
sub-pixel accuracy is required. To illustrate, the present approach is
applied to the inspection of printed circuits on a flat panel. Numerical
example shows that the present approach is effective and accurate
when target images contain a sufficient number of line segments,
which is true in many industrial problems.
Abstract: Multiprocessor task scheduling is a NP-hard problem and Genetic Algorithm (GA) has been revealed as an excellent technique for finding an optimal solution. In the past, several methods have been considered for the solution of this problem based on GAs. But, all these methods consider single criteria and in the present work, minimization of the bi-criteria multiprocessor task scheduling problem has been considered which includes weighted sum of makespan & total completion time. Efficiency and effectiveness of genetic algorithm can be achieved by optimization of its different parameters such as crossover, mutation, crossover probability, selection function etc. The effects of GA parameters on minimization of bi-criteria fitness function and subsequent setting of parameters have been accomplished by central composite design (CCD) approach of response surface methodology (RSM) of Design of Experiments. The experiments have been performed with different levels of GA parameters and analysis of variance has been performed for significant parameters for minimisation of makespan and total completion time simultaneously.
Abstract: Moisture is an important consideration in many
aspects ranging from irrigation, soil chemistry, golf course, corrosion
and erosion, road conditions, weather predictions, livestock feed
moisture levels, water seepage etc. Vegetation and crops always
depend more on the moisture available at the root level than on
precipitation occurrence. In this paper, design of an instrument is
discussed which tells about the variation in the moisture contents of
soil. This is done by measuring the amount of water content in soil by
finding the variation in capacitance of soil with the help of a
capacitive sensor. The greatest advantage of soil moisture sensor is
reduced water consumption. The sensor is also be used to set lower
and upper threshold to maintain optimum soil moisture saturation and
minimize water wilting, contributes to deeper plant root growth
,reduced soil run off /leaching and less favorable condition for insects
and fungal diseases. Capacitance method is preferred because, it
provides absolute amount of water content and also measures water
content at any depth.
Abstract: Compacted clay liners (CCLs) are the main materials
used in waste disposal landfills due to their low permeability. In this
study, the effect on the shear resistant of clays with inorganic salt
solutions as permeate fluid was experimentally investigated. For this
purpose, NaCl inorganic salt solution at concentrations of 2, 5, 10%
and deionized water were used. Laboratory direct shear and Vane
shear tests were conducted on three compacted clays with low,
medium and high plasticity. Results indicated that the solutions type
and its concentration affect the shear properties of the mixture. In the
light of this study, the influence magnitude of these inorganic salts in
varies concentrations in different clays were determined and more
suitable compacted clay with the compare of plasticity were found.
Abstract: In research on natural ventilation, and passive cooling
with forced convection, is essential to know how heat flows in a solid
object and the pattern of temperature distribution on their surfaces,
and eventually how air flows through and convects heat from the
surfaces of steel under roof. This paper presents some results from
running the computational fluid dynamic program (CFD) by
comparison between natural ventilation and forced convection within
roof attic that is received directly from solar radiation. The CFD
program for modeling air flow inside roof attic has been modified to
allow as two cases. First case, the analysis under natural ventilation,
is closed area in roof attic and second case, the analysis under forced
convection, is opened area in roof attic. These extend of all cases to
available predictions of variations such as temperature, pressure, and
mass flow rate distributions in each case within roof attic. The
comparison shows that this CFD program is an effective model for
predicting air flow of temperature and heat transfer coefficient
distribution within roof attic. The result shows that forced convection
can help to reduce heat transfer through roof attic and an around area
of steel core has temperature inner zone lower than natural
ventilation type. The different temperature on the steel core of roof
attic of two cases was 10-15 oK.
Abstract: Random Forests are a powerful classification technique, consisting of a collection of decision trees. One useful feature of Random Forests is the ability to determine the importance of each variable in predicting the outcome. This is done by permuting each variable and computing the change in prediction accuracy before and after the permutation. This variable importance calculation is similar to a one-factor-at a time experiment and therefore is inefficient. In this paper, we use a regular fractional factorial design to determine which variables to permute. Based on the results of the trials in the experiment, we calculate the individual importance of the variables, with improved precision over the standard method. The method is illustrated with a study of student attrition at Monash University.
Abstract: There is increasing evidence that earthquakes produce electromagnetic signals observable at the surface in the extremely low to very low freqency (ELF - VLF) range often in advance to the main event. These precursors are candidates for prediction purposes. Laboratory experiments con´¼ürm that material under load emits an electromagnetic signature, the detailed generation mechanisms how- ever are not well understood yet.
Abstract: The social force model which belongs to the
microscopic pedestrian studies has been considered as the supremacy
by many researchers and due to the main feature of reproducing the
self-organized phenomena resulted from pedestrian dynamic. The
Preferred Force which is a measurement of pedestrian-s motivation to
adapt his actual velocity to his desired velocity is an essential term on
which the model was set up. This Force has gone through stages of
development: first of all, Helbing and Molnar (1995) have modeled
the original force for the normal situation. Second, Helbing and his
co-workers (2000) have incorporated the panic situation into this
force by incorporating the panic parameter to account for the panic
situations. Third, Lakoba and Kaup (2005) have provided the
pedestrians some kind of intelligence by incorporating aspects of the
decision-making capability. In this paper, the authors analyze the
most important incorporations into the model regarding the preferred
force. They make comparisons between the different factors of these
incorporations. Furthermore, to enhance the decision-making ability
of the pedestrians, they introduce additional features such as the
familiarity factor to the preferred force to let it appear more
representative of what actually happens in reality.