Abstract: This paper compares the energy and exergy efficiency of a vapour compression refrigeration system using refrigerants of different groups. In this study, five different refrigerants including R507A, R134a, R114, R22 and R717 have been studied. EES Program is used to solve the thermodynamic equations. The results of this analysis are shown graphically. Based on the results, energy and exergy efficiencies for R717 are higher than the other refrigerants. Also, the energy and exergy efficiencies will be decreased with increasing the condensing temperature and decreasing the evaporating temperature.
Abstract: Efficient energy storage is a crucial factor in facilitating the uptake of renewable energy resources. Among the many options available for energy storage systems required to balance imbalanced supply and demand cycles, compressed air energy storage (CAES) is a proven technology in grid-scale applications. This paper reviews the current state of micro scale CAES technology and describes a micro-scale advanced adiabatic CAES (A-CAES) system, where heat generated during compression is stored for use in the discharge phase. It will also describe a thermodynamic model, developed in EES (Engineering Equation Solver) to evaluate the performance and critical parameters of the discharge phase of the proposed system. Three configurations are explained including: single turbine without preheater, two turbines with preheaters, and three turbines with preheaters. It is shown that the micro-scale A-CAES is highly dependent upon key parameters including; regulator pressure, air pressure and volume, thermal energy storage temperature and flow rate and the number of turbines. It was found that a micro-scale AA-CAES, when optimized with an appropriate configuration, could deliver energy input to output efficiency of up to 70%.
Abstract: In a fast growing region, conversion of agricultural lands which are surrounded by some new development sites will occur sooner than expected. This phenomenon has been experienced by many regions in Indonesia, especially the fringe of Jakarta (BoDeTaBek). Being Indonesia’s capital city, rapid conversion of land in this area is an unavoidable process. The land conversion expands spatially into the fringe regions, which were initially dominated by agricultural land or conservation sites. Without proper control or growth management, this activity will invite greater costs than benefits. The current land use is the use which maximizes its value. In order to maintain land for agricultural activity or conservation, some efforts are needed to keep the land value of this activity as high as possible. In this case, the knowledge regarding the functional relationship between land value and its driving forces is necessary. In a fast growing region, development externalities are the assumed dominant driving force. Land value is the product of the past decision of its use leading to its value. It is also affected by the local characteristics and the observed surrounded land use (externalities) from the previous period. The effect of each factor on land value has dynamic and spatial virtues; an empirical spatial dynamic land value model will be more useful to capture them. The model will be useful to test and to estimate the extent of land use externalities on land value in the short run as well as in the long run. It serves as a basis to formulate an effective urban growth management’s policy. This study will apply the model to the case of land value in the fringe of Jakarta Metropolitan. The model will be used further to predict the effect of externalities on land value, in the form of prediction map. For the case of Jakarta’s fringe, there is some evidence about the significance of neighborhood urban activity – negative externalities, the previous land value and local accessibility on land value. The effects are accumulated dynamically over years, but they will fully affect the land value after six years.
Abstract: Nowadays, huge amount of multimedia repositories
make the browsing, retrieval and delivery of video contents very slow
and even difficult tasks. Video summarization has been proposed to
improve faster browsing of large video collections and more efficient
content indexing and access. In this paper, we focus on approaches to
video summarization. The video summaries can be generated in many
different forms. However, two fundamentals ways to generate
summaries are static and dynamic. We present different techniques
for each mode in the literature and describe some features used for
generating video summaries. We conclude with perspective for
further research.
Abstract: Excavation of shallow tunnels such as subways in urban areas plays a significant role as a life line and investigation of the soil behavior against tunnel construction is one of the vital subjects studied in the geotechnical scope. Nowadays, urban tunnels are mostly drilled by T.B.Ms and changing the applied forces to tunnel lining is one of the most risky matters while drilling tunnels by these machines. Variation of soil cementation can change the behavior of these forces in the tunnel lining. Therefore, this article is designed to assess the impact of tunnel excavation in different soils and several amounts of cementation on applied loads to tunnel lining under static and dynamic loads. According to the obtained results, changing the cementation of soil will affect the applied loadings to the tunnel envelope significantly. It can be determined that axial force in tunnel lining decreases considerably when soil cementation increases. Also, bending moment and shear force in tunnel lining decreases as the soil cementation increases and causes bending and shear behavior of the segments to improve. Based on the dynamic analyses, as cohesion factor in soil increases, bending moment, axial and shear forces of segments decrease but lining behavior of the tunnel is the same as static state. The results show that decreasing the overburden applied to lining caused by cementation is different in two static and dynamic states.
Abstract: Microarray gene expression data play a vital in biological processes, gene regulation and disease mechanism. Biclustering in gene expression data is a subset of the genes indicating consistent patterns under the subset of the conditions. Finding a biclustering is an optimization problem. In recent years, swarm intelligence techniques are popular due to the fact that many real-world problems are increasingly large, complex and dynamic. By reasons of the size and complexity of the problems, it is necessary to find an optimization technique whose efficiency is measured by finding the near optimal solution within a reasonable amount of time. In this paper, the algorithmic concepts of the Particle Swarm Optimization (PSO), Shuffled Frog Leaping (SFL) and Cuckoo Search (CS) algorithms have been analyzed for the four benchmark gene expression dataset. The experiment results show that CS outperforms PSO and SFL for 3 datasets and SFL give better performance in one dataset. Also this work determines the biological relevance of the biclusters with Gene Ontology in terms of function, process and component.
Abstract: Metrics is the process by which numbers or symbols
are assigned to attributes of entities in the real world in such a way as
to describe them according to clearly defined rules. Software metrics
are instruments or ways to measuring all the aspect of software
product. These metrics are used throughout a software project to
assist in estimation, quality control, productivity assessment, and
project control. Object oriented software metrics focus on
measurements that are applied to the class and other characteristics.
These measurements convey the software engineer to the behavior of
the software and how changes can be made that will reduce
complexity and improve the continuing capability of the software.
Object oriented software metric can be classified in two types static
and dynamic. Static metrics are concerned with all the aspects of
measuring by static analysis of software and dynamic metrics are
concerned with all the measuring aspect of the software at run time.
Major work done before, was focusing on static metric. Also some
work has been done in the field of dynamic nature of the software
measurements. But research in this area is demanding for more work.
In this paper we give a set of dynamic metrics specifically for
polymorphism in object oriented system.
Abstract: Using electrical machine in conventional vehicles, also called hybrid vehicles, has become a promising control scheme that enables some manners for fuel economy and driver assist for better stability. In this paper, vehicle stability control, fuel economy and Driving/Regeneration braking for a 4WD hybrid vehicle is investigated by using an electrical machine on each non-driven wheels. In front wheels driven vehicles, fuel economy and regenerative braking can be obtained by summing torques applied on rear wheels. On the other hand, unequal torques applied to rear wheels provides enhanced safety and path correction in steering. In this paper, a model with fourteen degrees of freedom is considered for vehicle body, tires and, suspension systems. Thereafter, powertrain subsystems are modeled. Considering an electrical machine on each rear wheel, a fuzzy controller is designed for each driving, braking, and stability conditions. Another fuzzy controller recognizes the vehicle requirements between the driving/regeneration and stability modes. Intelligent vehicle control to multi objective operation and forward simulation are the paper advantages. For reaching to these aims, power management control and yaw moment control will be done by three fuzzy controllers. Also, the above mentioned goals are weighted by another fuzzy sub-controller base on vehicle dynamic. Finally, Simulations performed in MATLAB/SIMULINK environment show that the proposed structure can enhance the vehicle performance in different modes effectively.
Abstract: There was studied dynamic of the number of
nematodes fauna of various ecosystems of Gombori Mountain Ridge
that belongs to peak of fauna dynamic. The nature of dynamic is in
general similar in all six biotypes and the difference is evident only in
total number of nematodes.
Abstract: The use of statistical data and of the neural networks, capable of elaborate a series of data and territorial info, have allowed the making of a model useful in the subdivision of urban places into homogeneous zone under the profile of a social, real estate, environmental and urbanist background of a city. The development of homogeneous zone has fiscal and urbanist advantages. The tools in the model proposed, able to be adapted to the dynamic changes of the city, allow the application of the zoning fast and dynamic.
Abstract: In this paper, a two-dimensional (2D) numerical
model for the tidal currents simulation in Persian Gulf is presented.
The model is based on the depth averaged equations of shallow water
which consider hydrostatic pressure distribution. The continuity
equation and two momentum equations including the effects of bed
friction, the Coriolis effects and wind stress have been solved. To
integrate the 2D equations, the Alternative Direction Implicit (ADI)
technique has been used. The base of equations discritization was
finite volume method applied on rectangular mesh. To evaluate the
model validation, a dam break case study including analytical
solution is selected and the comparison is done. After that, the
capability of the model in simulation of tidal current in a real field is
represented by modeling the current behavior in Persian Gulf. The
tidal fluctuations in Hormuz Strait have caused the tidal currents in
the area of study. Therefore, the water surface oscillations data at
Hengam Island on Hormoz Strait are used as the model input data.
The check point of the model is measured water surface elevations at
Assaluye port. The comparison between the results and the
acceptable agreement of them showed the model ability for modeling
marine hydrodynamic.
Abstract: In this paper we propose a robust adaptive fuzzy
controller for a class of nonlinear system with unknown dynamic.
The method is based on type-2 fuzzy logic system to approximate
unknown non-linear function. The design of the on-line adaptive
scheme of the proposed controller is based on Lyapunov technique.
Simulation results are given to illustrate the effectiveness of the
proposed approach.
Abstract: In most study fields, a phenomenon may not be
studied directly but it will be examined indirectly by phenomenon
model. Making an accurate model of system, there is attained new
information from modeled phenomenon without any charge, danger,
etc... there have been developed more solutions for describing and
analyzing the recent complicated systems but few of them have
analyzed the performance in the range of system description. Petri
nets are of limited solutions which may make such union. Petri nets
are being applied in problems related to modeling and designing the
systems. Theory of Petri nets allow a system to model
mathematically by a Petri net and analyzing the Petri net can then
determine main information of modeled system-s structure and
dynamic. This information can be used for assessing the performance
of systems and suggesting corrections in the system. In this paper,
beside the introduction of Petri nets, a real case study will be studied
in order to show the application of generalized stochastic Petri nets in
modeling a resource sharing production system and evaluating the
efficiency of its machines and robots. The modeling tool used here is
SHARP software which calculates specific indicators helping to
make decision.
Abstract: Organizations are supposed to be systems and
consequently require defining the notion of equilibrium within.
However, organizations comprise people and unavoidably entail their
irrational aspects. Then, the question is what is the organizational
equilibrium and equilibrating mechanisms considering these aspects.
Hence, some arguments are provided here to conceptualize human
unconsciousness, irrationalities and consequent uncertainties within
organizations in the form of a system of psychic dynamism. The
assumption is this dynamism maintains the psychic balance of the
organization through a psychodynamic point of view. The resultant
conceptualization expected to promote the understanding of such
aspects in different organizational settings by hypothesizing
organizational equilibration from this perspective. As a result, the
main expectation is, if it is known that how the organization
equilibrates in this sense, we can explain and deal with such
irrationalities and unconsciousness by rational and, of course
conscious, planning and accomplishing.
Abstract: In this paper, a model for an information retrieval
system is proposed which takes into account that knowledge about
documents and information need of users are dynamic. Two
methods are combined, one qualitative or symbolic and the other
quantitative or numeric, which are deemed suitable for many
clustering contexts, data analysis, concept exploring and
knowledge discovery. These two methods may be classified as
inductive learning techniques. In this model, they are introduced to
build “long term" knowledge about past queries and concepts in a
collection of documents. The “long term" knowledge can guide
and assist the user to formulate an initial query and can be
exploited in the process of retrieving relevant information. The
different kinds of knowledge are organized in different points of
view. This may be considered an enrichment of the exploration
level which is coherent with the concept of document/query
structure.
Abstract: Load balancing is the process of improving the
performance of a parallel and distributed system through a
redistribution of load among the processors [1] [5]. In this paper we
present the performance analysis of various load balancing
algorithms based on different parameters, considering two typical
load balancing approaches static and dynamic. The analysis indicates
that static and dynamic both types of algorithm can have
advancements as well as weaknesses over each other. Deciding type
of algorithm to be implemented will be based on type of parallel
applications to solve. The main purpose of this paper is to help in
design of new algorithms in future by studying the behavior of
various existing algorithms.
Abstract: Decrease in hardware costs and advances in computer
networking technologies have led to increased interest in the use of
large-scale parallel and distributed computing systems. One of the
biggest issues in such systems is the development of effective
techniques/algorithms for the distribution of the processes/load of a
parallel program on multiple hosts to achieve goal(s) such as
minimizing execution time, minimizing communication delays,
maximizing resource utilization and maximizing throughput.
Substantive research using queuing analysis and assuming job
arrivals following a Poisson pattern, have shown that in a multi-host
system the probability of one of the hosts being idle while other host
has multiple jobs queued up can be very high. Such imbalances in
system load suggest that performance can be improved by either
transferring jobs from the currently heavily loaded hosts to the lightly
loaded ones or distributing load evenly/fairly among the hosts .The
algorithms known as load balancing algorithms, helps to achieve the
above said goal(s). These algorithms come into two basic categories -
static and dynamic. Whereas static load balancing algorithms (SLB)
take decisions regarding assignment of tasks to processors based on
the average estimated values of process execution times and
communication delays at compile time, Dynamic load balancing
algorithms (DLB) are adaptive to changing situations and take
decisions at run time.
The objective of this paper work is to identify qualitative
parameters for the comparison of above said algorithms. In future this
work can be extended to develop an experimental environment to
study these Load balancing algorithms based on comparative
parameters quantitatively.
Abstract: Sensory input plays an important role to human
posture control system to initiate strategy in order to counterpart any
unbalance condition and thus, prevent fall. In previous study, joint
stiffness was observed able to describe certain issues regarding to
movement performance. But, correlation between balance ability and
joint stiffness is still remains unknown. In this study, joint stiffening
strategy at ankle and hip were observed under different sensory
manipulations and its correlation with conventional clinical test
(Functional Reach Test) for balance ability was investigated. In order
to create unstable condition, two different surface perturbations (tilt
up-tilt (TT) down and forward-backward (FB)) at four different
frequencies (0.2, 0.4, 0.6 and 0.8 Hz) were introduced. Furthermore,
four different sensory manipulation conditions (include vision and
vestibular system) were applied to the subject and they were asked to
maintain their position as possible. The results suggested that joint
stiffness were high during difficult balance situation. Less balance
people generated high average joint stiffness compared to balance
people. Besides, adaptation of posture control system under repetitive
external perturbation also suggested less during sensory limited
condition. Overall, analysis of joint stiffening response possible to
predict unbalance situation faced by human
Abstract: The purpose of this paper is to perform a multidisciplinary design and analysis (MDA) of honeycomb panels used in the satellites structural design. All the analysis is based on clamped-free boundary conditions. In the present work, detailed finite element models for honeycomb panels are developed and analysed. Experimental tests were carried out on a honeycomb specimen of which the goal is to compare the previous modal analysis made by the finite element method as well as the existing equivalent approaches. The obtained results show a good agreement between the finite element analysis, equivalent and tests results; the difference in the first two frequencies is less than 4% and less than 10% for the third frequency. The results of the equivalent model presented in this analysis are obtained with a good accuracy. Moreover, investigations carried out in this research relate to the honeycomb plate modal analysis under several aspects including the structural geometrical variation by studying the various influences of the dimension parameters on the modal frequency, the variation of core and skin material of the honeycomb. The various results obtained in this paper are promising and show that the geometry parameters and the type of material have an effect on the value of the honeycomb plate modal frequency.
Abstract: The social force model which belongs to the
microscopic pedestrian studies has been considered as the supremacy
by many researchers and due to the main feature of reproducing the
self-organized phenomena resulted from pedestrian dynamic. The
Preferred Force which is a measurement of pedestrian-s motivation to
adapt his actual velocity to his desired velocity is an essential term on
which the model was set up. This Force has gone through stages of
development: first of all, Helbing and Molnar (1995) have modeled
the original force for the normal situation. Second, Helbing and his
co-workers (2000) have incorporated the panic situation into this
force by incorporating the panic parameter to account for the panic
situations. Third, Lakoba and Kaup (2005) have provided the
pedestrians some kind of intelligence by incorporating aspects of the
decision-making capability. In this paper, the authors analyze the
most important incorporations into the model regarding the preferred
force. They make comparisons between the different factors of these
incorporations. Furthermore, to enhance the decision-making ability
of the pedestrians, they introduce additional features such as the
familiarity factor to the preferred force to let it appear more
representative of what actually happens in reality.