Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: The present study focuses on methods allowing a convenient and quick calculation of the SIFs in order to predict the static adhesive strength of bonded joints. A new SIF calculation method is proposed, based on the stresses obtained from a FE model at a reference point located in the adhesive layer at equal distance of the free-edge and of the two interfaces. It is shown that, even limiting ourselves to the two main modes, i.e. the opening and the shearing modes, and using the values of the stresses resulting from a low detailed FE model, an efficient calculation of the peeling stress at adhesive-substrate corners can be obtained by this way. The proposed method is interesting in that it can be the basis of a prediction tool that will allow the designer to quickly evaluate the SIFs characterizing a particular application without developing a detailed analysis.
Abstract: Autofluorescence (AF) bronchoscopy is an
established method to detect dysplasia and carcinoma in situ (CIS).
For this reason the “Sotiria" Hospital uses the Karl Storz D-light
system. However, in early tumor stages the visualization is not that
obvious. With the help of a PC, we analyzed the color images we
captured by developing certain tools in Matlab®. We used statistical
methods based on texture analysis, signal processing methods based
on Gabor models and conversion algorithms between devicedependent
color spaces. Our belief is that we reduced the error made
by the naked eye. The tools we implemented improve the quality of
patients' life.
Abstract: Urban water management in Australia faces increasing pressure to deal with the challenges of droughts, growing population and the climate change uncertainty. Addressing these challenges is an opportunity to incorporate the parallel goals of sustainable water management and climate change adaptation through holistic, non-technical means. This paper presents case studies from Perth and Sydney which show how despite robust adaptation plans and experience, recent efforts to 'drought proof' cities have focused on supply-side measures (i.e. desalination), rather than rethinking how water is used and managing demand. The trend towards desalination as a climate adaptation measure raises questions about the sustainability of urban water futures in Australia.
Abstract: The objective of this research was to determine the
potency of indigenous acid-aluminium tolerant Bradyrhizobium
japonicum as producer of indole acetic acid (IAA) and applied it as
nitrogen fixation on local soybeans viz Anjasmoro, Tanggamus
(yellow soybean seeds), and Detam (black soybean seed). Three
isolates of acid-aluminium tolerant Bradyrhizobium japonicum (BJ)
were used in this research, i.e. BJ 11 (wt), BJ 11 (19) - BJ 11(wt)
mutant, and USDA 110 as a reference isolate. All of isolates tested to
produce the IAA by using Salkowsky method. Effect of IAA
production by each of B. japonicum was tested on growth pouch and
greenhouse using three varieties of soybean. All isolates could grow
well and produce IAA on yeast mannitol broth (YMB) medium in
the presence of 0.5 mM L-tryptophan. BJ 11 (19) produced the
highest of IAA at 4 days incubation compared to BJ 11 (wt) and
USDA 110. All tested isolates of Bradyrhizobium japonicum have
showed effect on stimulating the formation of root nodules in
soybean varieties grown on Leonard bottle. The concentration of
IAA on root nodules of soybean symbiotic with B. japonicum was
significantly different with control, except on the treatment using
Tanggamus soybean.
Abstract: The purpose of this study is to analyze the cognitive
and travel experience the situation of the tourist attraction of the sport
tourism in Penghu. This study used a questionnaires, the main island
of Taiwan to Penghu in the way of marine sports tourists adopted the
designated convenience sampling method, a total of 1447 valid
questionnaires. After statistical analysis, this study found that: 1.
Tourists to Penghu sports tourism attraction cognitive as “good air
quality, suitable for water activities". 2. Tourists in Penghu's tourism
experience, “Let me taste the delicious specialties and snacks". 3. The
attraction of the sport tourism, travel experience and perceived value
are correlated, and both the perceived value with a high degree of
predictive ability. Based on the findings of this study not only for
Penghu's tourism industry with the unit in charge of the proposed
operating and suggestions for future research to other researchers.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: This study aims to explore the relationship between the
disposition effect and herding behavior of investors trading Taiwanese
information technology stocks. This study differs from previous
literature in two aspects. First, in contrast with the earlier studies that
focused on investigating investors’ herding behavior, this study
explores the possibility that the disposition effect drives investors’
herding behavior. Additionally, it takes an in-depth look at the
interdependence between the disposition effect and herding behavior
of investors, including lead-lag relationship and volatility transmission
effect. Empirical results show that investors trading Taiwan’s
information technology stocks exhibit pronounced herding behavior
and that the disposition effect has a great impact on their herding
behavior.
Abstract: In this paper, the wear of high speed steel hobs during
hobbing has been studied. The wear mechanisms are strongly
influenced by the choice of cutting speed. At moderate and high
cutting speeds three major wear mechanisms were identified:
abrasion, mild adhesive and severe adhesive. The microstructure and
wear behavior of two high speed steel grades (M2 and ASP30) has
been compared. In contrast, a variation in chemical composition or
microstructure of HSS tool material generally did not change the
dominant wear mechanism. However, the tool material properties
determine the resistance against the operating wear mechanism and
consequently the tool life. The metallographic analysis and wear
measurement at the tip of hob teeth included scanning electron
microscopy and stereoscope microscopy. Roughness profilometery is
used for measuring the gear surface roughness.
Abstract: These days MANET is attracting much attention as
they are expected to gratefully influence communication between
wireless nodes. Along with this great strength, there is much more
chance of leave and being attacked by a malicious node. Due to this
reason much attention is given to the security and the private issue in
MANET. A lot of research in MANET has been doing. In this paper
we present the overview of MANET, the security issues of MANET,
IP configuration in MANET, the solution to puzzle out the security
issues and the simulation of the proposal idea. We add the method to
figure out the malicious nodes so that we can prevent the attack from
them. Nodes exchange the information about nodes to prevent DAD
attack. We can get 30% better performance than the previous
MANETConf.
Abstract: In this paper the gradient based iterative algorithms are presented to solve the following four types linear matrix equations: (a) AXB = F; (b) AXB = F, CXD = G; (c) AXB = F s. t. X = XT ; (d) AXB+CYD = F, where X and Y are unknown matrices, A,B,C,D, F,G are the given constant matrices. It is proved that if the equation considered has a solution, then the unique minimum norm solution can be obtained by choosing a special kind of initial matrices. The numerical results show that the proposed method is reliable and attractive.
Abstract: The requirement to improve software productivity has
promoted the research on software metric technology. There are
metrics for identifying the quality of reusable components but the
function that makes use of these metrics to find reusability of
software components is still not clear. These metrics if identified in
the design phase or even in the coding phase can help us to reduce the
rework by improving quality of reuse of the component and hence
improve the productivity due to probabilistic increase in the reuse
level. CK metric suit is most widely used metrics for the objectoriented
(OO) software; we critically analyzed the CK metrics, tried
to remove the inconsistencies and devised the framework of metrics
to obtain the structural analysis of OO-based software components.
Neural network can learn new relationships with new input data and
can be used to refine fuzzy rules to create fuzzy adaptive system.
Hence, Neuro-fuzzy inference engine can be used to evaluate the
reusability of OO-based component using its structural attributes as
inputs. In this paper, an algorithm has been proposed in which the
inputs can be given to Neuro-fuzzy system in form of tuned WMC,
DIT, NOC, CBO , LCOM values of the OO software component and
output can be obtained in terms of reusability. The developed
reusability model has produced high precision results as expected by
the human experts.
Abstract: The quantified residence time distribution (RTD)
provides a numerical characterization of mixing in a reactor, thus
allowing the process engineer to better understand mixing
performance of the reactor.This paper discusses computational
studies to investigate flow patterns in a two impinging streams
cyclone reactor(TISCR) . Flow in the reactor was modeled with
computational fluid dynamics (CFD). Utilizing the Eulerian-
Lagrangian approach, implemented in FLUENT (V6.3.22), particle
trajectories were obtained by solving the particle force balance
equations. From simulation results obtained at different Δts, the mean
residence time (tm) and the mean square deviation (σ2) were
calculated. a good agreement can be observed between predicted and
experimental data. Simulation results indicate that the behavior of
complex reactor systems can be predicted using the CFD technique
with minimum data requirement for validation.
Abstract: This paper presents a heuristic approach to solve the Generalized Assignment Problem (GAP) which is NP-hard. It is worth mentioning that many researches used to develop algorithms for identifying the redundant constraints and variables in linear programming model. Some of the algorithms are presented using intercept matrix of the constraints to identify redundant constraints and variables prior to the start of the solution process. Here a new heuristic approach based on the dominance property of the intercept matrix to find optimal or near optimal solution of the GAP is proposed. In this heuristic, redundant variables of the GAP are identified by applying the dominance property of the intercept matrix repeatedly. This heuristic approach is tested for 90 benchmark problems of sizes upto 4000, taken from OR-library and the results are compared with optimum solutions. Computational complexity is proved to be O(mn2) of solving GAP using this approach. The performance of our heuristic is compared with the best state-ofthe- art heuristic algorithms with respect to both the quality of the solutions. The encouraging results especially for relatively large size test problems indicate that this heuristic approach can successfully be used for finding good solutions for highly constrained NP-hard problems.
Abstract: A horizontal anaerobic digester was developed and
tested in pilot scale for Korean food waste with high water contents
(>80%). The hydrogen sulfide in the biogas was removed by a
biological desulfurization equipment integrated in the horizontal
digester. A mixer of the horizontal digester was designed to easily
remove the sediment in the bottom and scum layers on surface in the
digester. Experimental result for 120 days of operation of the pilot
plant showed a high removal efficiency of 81.2% for organic
substance and high stability during the whole operation period were
acquired. Also food waste was treated at high organic loading rates
over 4 kg•VS/m3∙day and a methane gas production rate of 0.62
m3/kg•VSremoved was accomplished.
The biological desulfurization equipment inside the horizontal
digester was proven to be an economic and effective method to reduce
the biogas desulfurization cost by removing hydrogen sulfide more
than 90% without external desulfurization equipments.
Abstract: In this study, a new procedure for inspecting damages on LNG storage tanks was proposed with the use of structural diagnostic techniques: i.e., nondestructive inspection techniques such as macrography, the hammer sounding test, the Schmidt hammer test, and the ultrasonic pulse velocity test, and destructive inspection techniques such as the compressive strength test, the chloride penetration test, and the carbonation test. From the analysis of all the test results, it was concluded that the LNG storage tank cover was in good condition. Such results were also compared with the Korean concrete standard specifications and design values. In addition, the remaining life of the LNG storage tank was estimated by using existing models. Based on the results, an LNG storage tank cover performance evaluation procedure was suggested.
Abstract: After a strong earthquake occurs, a secondary disaster due to strong aftershocks, flood, landslide or heavy snow can possible to occur and the secondary disaster due to resident-s action also can possible to happen. However, until now seldom researchers have paid attention at it. This paper focused on the Inhabitant-s action after the strong earthquake occurs when a terrible even becomes calm. An inappropriate behavior of people with disadvantaged climate after the worse earthquake can bring a tragedy to their life.
Abstract: This paper presents design and implements the
T-DOF PI controller design for a speed control of induction motor.
The voltage source inverter type space vector pulse width modulation
technique is used the drive system. This scheme leads to be able to
adjust the speed of the motor by control the frequency and amplitude
of the input voltage. The ratio of input stator voltage to frequency
should be kept constant. The T-DOF PI controller design by root
locus technique is also introduced to the system for regulates and
tracking speed response. The experimental results in testing the 120
watt induction motor from no-load condition to rated condition show
the effectiveness of the proposed control scheme.
Abstract: Silk sericin (SS) is a glue-like protein from silkworm
cocoon. With its outstanding moisturization and activation collagen
synthesis properties, silk protein is applied for wound healing. Since
wound dressing in film preparation can facilitate patients-
convenience and reduce risk of wound contraction, SS and polyvinyl
alcohol (PVA) films were prepared with various concentrations of
SS. Their physical properties such as surface density, light
transmission, protein dissolution and tensile modulus were
investigated. The results presented that 3% SS with 2% PVA is the
best ingredient for SS film forming.
Abstract: In this paper we study some numerical methods to solve a model one-dimensional convection–diffusion equation. The semi-discretisation of the space variable results into a system of ordinary differential equations and the solution of the latter involves the evaluation of a matrix exponent. Since the calculation of this term is computationally expensive, we study some methods based on Krylov subspace and on Restrictive Taylor series approximation respectively. We also consider the Chebyshev Pseudospectral collocation method to do the spatial discretisation and we present the numerical solution obtained by these methods.