Abstract: In this paper we study the resource allocation problem
for an OFDMA based cooperative two-way relaying (TWR) network.
We focus on amplify and forward (AF) analog network coding
(ANC) protocol. An optimization problem for two basic resources
namely, sub-carrier and power is formulated for multi-user TWR
networks. A joint optimal optimization problem is investigated and
two-step low complexity sub-optimal resource allocation algorithm is
proposed for multi-user TWR networks with ANC protocol. The
proposed algorithm has been evaluated in term of total achievable
system sum-rate and achievable individual sum-rate for each userpair.
The good tradeoff between system sum-rate and fairness is
observed in the two-step proportional resource allocation scheme.
Abstract: Launch and recovery helicopter wind envelope for a
ship type was determined as the first step to the helicopter
qualification program. Flight deck velocities data were obtained by
means of a two components laser Doppler anemometer testing a
1/50th model in the wind tunnel stream. Full-scale flight deck
measurements were obtained on board the ship using a sonic
anemometer. Wind tunnel and full-scale measurements were
compared, showing good agreement and finally, a preliminary launch
and recovery helicopter wind envelope for this specific ship was
built.
Abstract: The characteristic bending strength (MOR) and mean
modulus of elasticity (MOE) of tropical hardwood red seraya (Shorea
spp.) plywood were determined using European Standard EN310 and
EN789. The thickness of the test specimen was 4.0mm, 7.0mm,
9.0mm, 12.0mm and 15.0mm. The experiment found that the MOR
of red seraya plywood in EN310 is about 12% to 20% and 7% to
24% higher than EN789 whereas MOE were about 28% to 41% and
30% to 36% lower than those obtained from EN 789 for test
specimens parallel and perpendicular to the grain direction. The
linear regression shows that MOR and MOE for EN789 is about 0.8
times less and 1.5 times more than EN310. The experiment also
found that the MOR and MOE of EN310 and EN789 also depend on
the wood species that used in the experiment.
Abstract: This research aimed to develop plasma system used in air conditioners. This developed plasma system could be installed in the air conditioners - all split type. The quality of air could be improved to be equal to present plasma system. Development processes were as follows: 1) to study the plasma system used in the air conditioners, 2) to design a plasma generator, 3) to develop the plasma generator, and 4) to test its performance in many types of the air conditioners. This plasma system was developed by AC high voltage – 14 kv with a frequency of 50 kHz. Carbon was a conductor to generate arc in air purifier system. The research was tested by installing the plasma generator in the air conditioners - wall type. Whereas, there were 3 types of installations: air flow out, air flow in, and room center. The result of the plasma generator installed in the air conditioners, split type, revealed that the air flow out installation provided the highest average of o-zone at 223 mg/h. This type of installation provided the highest efficiency of air quality improvement. Moreover, the air flow in installation and the room center installation provided the average of the o-zone at 163 mg/h and 64 mg/h, respectively.
Abstract: Among many agro- based cottage industries in India
sericulture has been promoted as an agro-based, labor intensive, rural
oriented cottage industry, providing gainful employment mainly to
the weaker and marginalized section of the society specially tribal.
Sericulture occupies the place of pride in the rural economy can be
practiced even with very low land holding, low gestation, high
returns make sericulture an ideal program, requiring little capital
investment. In 2010-2011 the employment in sericulture sector was
72.5 lakh persons. The involvement of landless rural people in tasar
sericulture is because they understood its potential for rural and tribal
upliftment. This article demonstrates that certain developmental
initiatives have been playing an important role in the socio-economic
progress of tribal masses in Raigarh district and explains the
increased returns from sericulture as a result of development
programs. The study concludes with some suggestions to improve the
long term feasibility of sericulture.
Abstract: Von Willebrand-s disease is the most common
inherited bleeding disorder in humans, it
caused by qualitative abnormalities of the von Willebrand factor
(vWF). Our objective is to determine the prevalence of this disease at
part of the Algerian population in the East and the South by a
biological diagnosis based on specific biological tests (automated
platelet count, the bleeding time (TS), the time of cephalin + activator
(TCA), measure of the prothrombin rate (TP), vWF rate and factor
VIII rate, Molecular electrophoresis of vWF multimers in agarose gel
in the presence of SDS). Four patients of type III or severe
Willebrand-s disease were found on 200 suspect cases. All cases are
showed a deficit in vWF rate (< 5%), and factor VIII (P
Abstract: The cost of developing the software from scratch can
be saved by identifying and extracting the reusable components from
already developed and existing software systems or legacy systems
[6]. But the issue of how to identify reusable components from
existing systems has remained relatively unexplored. We have used
metric based approach for characterizing a software module. In this
present work, the metrics McCabe-s Cyclometric Complexity
Measure for Complexity measurement, Regularity Metric, Halstead
Software Science Indicator for Volume indication, Reuse Frequency
metric and Coupling Metric values of the software component are
used as input attributes to the different types of Neural Network
system and reusability of the software component is calculated. The
results are recorded in terms of Accuracy, Mean Absolute Error
(MAE) and Root Mean Squared Error (RMSE).
Abstract: The purpose of this study was to explore the
demographic differences of international tourists according to three
main factors, including the value of time, shopping behavior and
shopping motivation. The Chatuchak Weekend Market is known as
one of the biggest weekend markets in the world. Too little academic
studies had been conducted in this area of weekend market, despite its
growth and continuous development. In general, both domestic
visitors and international tourists are attracted to the perception of
cheap and bargaining prices the weekend market. However, systematic
research study can provide reliable understanding of the perception of
the visitors.
This study focused on the group of international tourists who visited
the market and aimed to provide better insights based on the
differences in their demographic factors. Findings indicated that
several differences in value of time, shopping behavior, and shopping
motivation were identified by gender, income and age. Research
implications and directions for further studies were discussed.
Abstract: The survey and classification of the different security
attacks in structured peer-to-peer (P2P) overlay networks can be
useful to computer system designers, programmers, administrators,
and users. In this paper, we attempt to provide a taxonomy of
structured P2P overlay networks security attacks. We have specially
focused on the way these attacks can arise at each level of the
network. Moreover, we observed that most of the existing systems
such as Content Addressable Network (CAN), Chord, Pastry,
Tapestry, Kademlia, and Viceroy suffer from threats and vulnerability
which lead to disrupt and corrupt their functioning. We hope that our
survey constitutes a good help for who-s working on this area of
research.
Abstract: Infrared focal plane arrays (IRFPA) sensors, due to
their high sensitivity, high frame frequency and simple structure, have
become the most prominently used detectors in military applications.
However, they suffer from a common problem called the fixed pattern
noise (FPN), which severely degrades image quality and limits the
infrared imaging applications. Therefore, it is necessary to perform
non-uniformity correction (NUC) on IR image. The algorithms of
non-uniformity correction are classified into two main categories, the
calibration-based and scene-based algorithms. There exist some
shortcomings in both algorithms, hence a novel non-uniformity
correction algorithm based on non-linear fit is proposed, which
combines the advantages of the two algorithms. Experimental results
show that the proposed algorithm acquires a good effect of NUC with
a lower non-uniformity ratio.
Abstract: An experiment was conducted under controlled
conditions to study the effect of water extract of leaves, shoots and
roots of either Sisymbrium irio L. =SISIR and/or Descurainia
sophia (L.) Schur =DESSO on the germination and primary growth
of wheat. A split-split plot experiment in CRD with three
replications was used. The main plots were the type of weed: i.e.
SISIR and DESSO and the sub-plots were type of organ: i.e. leaf,
stem and root and, the sub-sub plots were concentration of the
water extract of each organ of the weeds: i.e. 0, 2, 4 and 8 % w/v.
The plant materials were cut in 2-3 cm pieces and then were
ground in a blender. The crushed materials were weighed
according to experimental protocol and the final volume was
reached to 100 ml in distilled water in dark bottles. All bottles were
put on a shaker for 24 hours. The solutions were filtered by muslin
cloth. Whatman paper, 9 cm in diameter, were put in petri dishes
and twenty seeds of wheat were put on it and 5 ml distilled water
or water extract of weeds were added to each petri dish. All petri
dishes were put in constant temperature of 15 0C incubator.
The results showed that the SISIR water extract had a greater
inhibitory effects on germination and primary growth of wheat
than those of DESSO water extract. The water extracts of the
leaves of both weeds had the greatest inhibitory effects on
germination and primary growth of wheat, compared to those of
stems and roots. Increasing the concentration of water extract of
leaves, stems and roots of both weeds up to 8 % caused the greatest
inhibitory effects to wheat and reduced the germination rate and
primary growth of it linearly.
Abstract: A study concerning the photocatalytic decolourization
of Congo red (CR) dye, over artificial UV irradiation is presented.
Photocatalysts based on a commercial titanium dioxide (TiO2)
modified with transition metals (Ni, Cu and Zn) were used. The
dopage method used was wet impregnation. A TiO2 sample without
salt was subjected to the same hydrothermal treatment to be used as
reference. Congo red solutions to several pH conditions (natural and
basic) were used to evaluate photocatalytic performance of each
doped catalysts. Photodecolourization percentage was measured
spectrofotrometically after 3 h of treatment to 499 nm as response
variable. Kinetics investigations of photodegradation indicated that
reactions obey to Langmuir-Hinshelwood model and pseudo–first
order law. The rate constant studies of photocatalytic decolourization
reactions for Zn–TiO2 and Cu–TiO2 photocatalysts indicated that in
all cases the rate constant of the reaction was higher than that of TiO2
undoped. These results show that nature of the metal modifying the
TiO2 influence on the efficiency of the photocatalyst evaluated in
process. Ni does not present an additional effect compared with TiO2,
while Zn enhances the photoactivity due to its electronic properties.
Abstract: Object-oriented simulation is considered one of the most sophisticated techniques that has been widely used in planning, designing, executing and maintaining construction projects. This technique enables the modeler to focus on objects which is extremely important for thorough understanding of a system. Thus, identifying an object is an essential point of building a successful simulation model. In a maintenance process an object is a maintenance work order (MWO). This study demonstrates a maintenance simulation model for the building maintenance division of Saudi Consolidated Electric Company (SCECO) in Dammam, Saudi Arabia. The model focused on both types of maintenance processes namely: (1) preventive maintenance (PM) and (2) corrective maintenance (CM). It is apparent from the findings that object-oriented simulation is a good diagnostic and experimental tool. This is because problems, limitations, bottlenecks and so forth are easily identified. These features are very difficult to obtain when using other tools.
Abstract: The main purpose of the research is to investigate the computer experiences and computer attitudes of prospective class teachers. The research also investigated the differences between computer attitudes and computer experiences, computer competencies and the influence of genders. Ninety prospective class teachers participated in the research. Computer Attitude Scale- Marmara (CAS-M), and a questionnaire, about their computer experiences, and opinions toward the use of computers in the classroom setting, were administrated. The major findings are as follows: (1) 62% of prospective class teachers have computer at home; (2) 50% of the computer owners have computers less than three years; (3) No significant differences were found between computer attitudes and gender; (4) Differences were found between general computer attitudes and computer liking attitudes of prospective class teachers based on their computer competencies in favor of more competent ones.
Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.
Abstract: Due to the fact that in the new century customers tend
to express globally increasing demands, networks of interconnected
businesses have been established in societies and the management of
such networks seems to be a major key through gaining competitive
advantages. Supply chain management encompasses such managerial
activities. Within a supply chain, a critical role is played by quality.
QFD is a widely-utilized tool which serves the purpose of not only
bringing quality to the ultimate provision of products or service
packages required by the end customer or the retailer, but it can also
initiate us into a satisfactory relationship with our initial customer;
that is the wholesaler. However, the wholesalers- cooperation is
considerably based on the capabilities that are heavily dependent on
their locations and existing circumstances. Therefore, it is undeniable
that for all companies each wholesaler possesses a specific
importance ratio which can heavily influence the figures calculated in
the House of Quality in QFD. Moreover, due to the competitiveness
of the marketplace today, it-s been widely recognized that
consumers- expression of demands has been highly volatile in
periods of production. Apparently, such instability and proneness to
change has been very tangibly noticed and taking it into account
during the analysis of HOQ is widely influential and doubtlessly
required. For a more reliable outcome in such matters, this article
demonstrates the application viability of Analytic Network Process
for considering the wholesalers- reputation and simultaneously
introduces a mortality coefficient for the reliability and stability of
the consumers- expressed demands in course of time. Following to
this, the paper provides further elaboration on the relevant
contributory factors and approaches through the calculation of such
coefficients. In the end, the article concludes that an empirical
application is needed to achieve broader validity.
Abstract: Impaired fertility may be the result of indirect
consumption of anti-fertility agents through food. Monosodium
glutamate (MSG) has been widely used as food additive, flavour
enhancer and included in vaccines. This study focuses in determining
the gonadotoxic and cytotoxic effect of MSG on selected sperm
parameters such as sperm viability, sperm membrane integrity and
testes cytoarchitecture of male mice via histological examination to
determine its effect on spermatogenesis. Twenty-four Mus musculus
were randomly divided into 4 groups and given intraperitoneal
injections (IP) daily for 14 days of different MSG concentrations at
250, 500 and 1000mg/kg MSG to body weight to induce obesity.
Saline was given to control group. Mice were sacrificed and analysis
revealed abnormalities in values for sperm parameters and damages
to testes cytoarchitecture of male mice. The results recorded
decreased viability (p0.05) with degenerative structures in seminiferous tubule of
testes. The results indicated various implications of MSG on male
mice reproductive system which has consequences in fertility
potential.
Abstract: Computer technology and the Internet have made a
breakthrough in the existence of data communication. This has
opened a whole new way of implementing steganography to ensure
secure data transfer. Steganography is the fine art of hiding the
information. Hiding the message in the carrier file enables the
deniability of the existence of any message at all. This paper designs
a stego machine to develop a steganographic application to hide data
containing text in a computer video file and to retrieve the hidden
information. This can be designed by embedding text file in a video
file in such away that the video does not loose its functionality using
Least Significant Bit (LSB) modification method. This method
applies imperceptible modifications. This proposed method strives
for high security to an eavesdropper-s inability to detect hidden
information.
Abstract: The area of Project Risk Management (PRM) has
been extensively researched, and the utilization of various tools and
techniques for managing risk in several industries has been
sufficiently reported. Formal and systematic PRM practices have
been made available for the construction industry. Based on such
body of knowledge, this paper tries to find out the global picture of
PRM practices and approaches with the help of a survey to look into
the usage of PRM techniques and diffusion of software tools, their
level of maturity, and their usefulness in the construction sector.
Results show that, despite existing techniques and tools, their usage is
limited: software tools are used only by a minority of respondents
and their cost is one of the largest hurdles in adoption. Finally, the
paper provides some important guidelines for future research
regarding quantitative risk analysis techniques and suggestions for
PRM software tools development and improvement.
Abstract: Simulation is a very helpful and valuable work tool in
manufacturing. It can be used in industrial field allowing the
system`s behavior to be learnt and tested. Simulation provides a low
cost, secure and fast analysis tool. It also provides benefits, which
can be reached with many different system configurations. Topics to
be discussed include: Applications, Modeling, Validating, Software
and benefits of simulation. This paper provides a comprehensive
literature review on research efforts in simulation.