Abstract: Orthogonal Frequency Division Multiplexing
(OFDM) is an efficient method of data transmission for high speed
communication systems. However, the main drawback of OFDM
systems is that, it suffers from the problem of high Peak-to-Average
Power Ratio (PAPR) which causes inefficient use of the High Power
Amplifier and could limit transmission efficiency. OFDM consist of
large number of independent subcarriers, as a result of which the
amplitude of such a signal can have high peak values. In this paper,
we propose an effective reduction scheme that combines DCT and
SLM techniques. The scheme is composed of the DCT followed by
the SLM using the Riemann matrix to obtain phase sequences for the
SLM technique. The simulation results show PAPR can be greatly
reduced by applying the proposed scheme. In comparison with
OFDM, while OFDM had high values of PAPR –about 10.4dB our
proposed method achieved about 4.7dB reduction of the PAPR with
low complexities computation. This approach also avoids
randomness in phase sequence selection, which makes it simpler to
decode at the receiver. As an added benefit, the matrices can be
generated at the receiver end to obtain the data signal and hence it is
not required to transmit side information (SI).
Abstract: Fixed-bed slow pyrolysis experiments of rice husk
have been conducted to determine the effect of pyrolysis
temperature, heating rate, particle size and reactor length on the
pyrolysis product yields. Pyrolysis experiments were performed at
pyrolysis temperature between 400 and 600°C with a constant
heating rate of 60°C/min and particle sizes of 0.60-1.18 mm. The
optimum process conditions for maximum liquid yield from the rice
husk pyrolysis in a fixed bed reactor were also identified. The highest
liquid yield was obtained at a pyrolysis temperature of 500°C,
particle size of
1.18-1.80 mm, with a heating rate of 60°C/min in a 300 mm length
reactor. The obtained yield of, liquid, gas and solid were found be in
the range of 22.57-31.78 %, 27.75-42.26 % and 34.17-42.52 % (all
weight basics) respectively at different pyrolysis conditions. The
results indicate that the effects of pyrolysis temperature and particle
size on the pyrolysis yield are more significant than that of heating
rate and reactor length. The functional groups and chemical
compositions present in the liquid obtained at optimum conditions
were identified by Fourier Transform-Infrared (FT-IR) spectroscopy
and Gas Chromatography/ Mass Spectroscopy (GC/MS) analysis
respectively.
Abstract: This work concerns the topological optimization
problem for determining the optimal petroleum refinery
configuration. We are interested in further investigating and
hopefully advancing the existing optimization approaches and
strategies employing logic propositions to conceptual process
synthesis problems. In particular, we seek to contribute to this
increasingly exciting area of chemical process modeling by
addressing the following potentially important issues: (a) how the
formulation of design specifications in a mixed-logical-and-integer
optimization model can be employed in a synthesis problem to enrich
the problem representation by incorporating past design experience,
engineering knowledge, and heuristics; and (b) how structural
specifications on the interconnectivity relationships by space (states)
and by function (tasks) in a superstructure should be properly
formulated within a mixed-integer linear programming (MILP)
model. The proposed modeling technique is illustrated on a case
study involving the alternative processing routes of naphtha, in which
significant improvement in the solution quality is obtained.
Abstract: Vision-based intelligent vehicle applications often require large amounts of memory to handle video streaming and image processing, which in turn increases complexity of hardware and software. This paper presents an FPGA implement of a vision-based blind spot warning system. Using video frames, the information of the blind spot area turns into one-dimensional information. Analysis of the estimated entropy of image allows the detection of an object in time. This idea has been implemented in the XtremeDSP video starter kit. The blind spot warning system uses only 13% of its logic resources and 95k bits block memory, and its frame rate is over 30 frames per sec (fps).
Abstract: The purpose of this paper is to consider the
introduction of online courses to replace the current classroom-based
staff training. The current training is practical, and must be
completed before access to the financial computer system is
authorized. The long term objective is to measure the efficacy,
effectiveness and efficiency of the training, and to establish whether
a transfer of knowledge back to the workplace has occurred. This
paper begins with an overview explaining the importance of staff
training in an evolving, competitive business environment and
defines the problem facing this particular organization. A summary
of the literature review is followed by a brief discussion of the
research methodology and objective. The implementation of the
alpha version of the online course is then described. This paper may
be of interest to those seeking insights into, or new theory regarding,
practical interventions of online learning in the real world.
Abstract: The effect of the rotational speed and axial torque on
the diagnostics of tapered rolling element bearing defects was
investigated. The accelerometer was mounted on the bearing housing
and connected to Sound and Vibration Analyzer (SVAN 958) and
was used to measure the accelerations from the bearing housing. The
data obtained from the bearing was processed to detect damage of the
bearing using statistical tools and the results were subsequently
analyzed to see if bearing damage had been captured. From this study
it can be seen that damage is more evident when the bearing is
loaded. Also, at the incipient stage of damage the crest factor and
kurtosis values are high but as time progresses the crest factors and
kurtosis values decrease whereas the peak and RMS values are low at
the incipient stage but increase with damage.
Abstract: In this paper an alternative visualisation approach of
the wake behind different vehicle body shapes with simplified and
fully-detailed underbody has been proposed and analysed. This
allows for a more clear distinction among the different wake regions.
This visualisation is based on a transformation of the cartesian
coordinates of a chosen wake plane to polar coordinates, using as
filter velocities lower than the freestream. This transformation
produces a polar wake plot that enables the division and
quantification of the wake in a number of sections. In this paper,
local drag has been used to visualise the drag contribution of the flow
by the different sections. Visually, a balanced wake can be observed
by the concentric behaviour of the polar plots. Alternatively,
integration of the local drag of each degree section as a ratio of the
total local drag yields a quantifiable approach of the wake uniformity,
where different sections contribute equally to the local drag, with the
exception of the wheels.
Abstract: Direct conversion of methane to methanol by partial oxidation in a thermal reactor has a poor yield of about 2% which is less than the expected economical yield of about 10%. Conventional thermal catalytic reactors have been proposed to be superseded by plasma reactors as a promising approach, due to strength of the electrical energy which can break C-H bonds of methane. Among the plasma techniques, non-thermal dielectric barrier discharge (DBD) plasma chemical process is one of the most future promising technologies in synthesizing methanol. The purpose of this paper is presenting a brief review of CH4 oxidation with O2 in DBD plasma reactors based on the recent investigations. For this reason, the effect of various parameters of reactor configuration, feed ratio, applied voltage, residence time (gas flow rate), type of applied catalyst, pressure and reactor wall temperature on methane conversion and methanol selectivity are discussed.
Abstract: Knee joint forces are available by in vivo measurement
using an instrumented knee prosthesis for small to moderate knee
flexion but not for high flexion yet. We created a 2D mathematical
model of the lower limb incorporating several new features such as a
patello-femoral mechanism, a thigh-calf contact at high knee flexion
and co-contracting muscles' force ratio, then used it to determine knee
joint forces arising from high knee flexions in four kneeling
conditions: rising with legs in parallel, with one foot forward, with or
without arm use. With arms used, the maximum values of knee joint
force decreased to about 60% of those with arms not used. When rising
with one foot forward, if arms are not used, the forward leg sustains a
force as large as that sustained when rising with legs parallel.
Abstract: An attempt has been made to determine the strength
and impact properties of Cr-Mo steel weld and base materials by
varying the current during manual metal arc welding. Toughness over
a temperature range from -32 to 100°C of base, heat affected zone
(HAZ) and weld zones at three current settings are made. It is
observed that the deterioration in notch toughness at any zone with
the temperature decreases. The values of notch toughness for all
zones at -32°C are almost same for any current settings. The values
of notch toughness at HAZ area are higher than that of weld area due
to the coarsening of ferrite grain of HAZ occurs with higher heat
input. From microhardness and microstructure result, it can be
concluded that large inclusion content in weld deposit is the cause of
lower notch toughness value.
Abstract: In this paper we ultra low-voltage and high speed CMOS domino logic. For supply voltages below 500mV the delay for a ultra low-voltage NAND2 gate is aproximately 10% of a complementary CMOS inverter. Furthermore, the delay variations due to mismatch is much less than for conventional CMOS. Differential domino gates for AND/NAND and OR/NOR operation are presented.
Abstract: A wireless sensor network with a large number of tiny sensor nodes can be used as an effective tool for gathering data in various situations. One of the major issues in wireless sensor networks is developing an energy-efficient routing protocol which has a significant impact on the overall lifetime of the sensor network. In this paper, we propose a novel hierarchical with static clustering routing protocol called Energy-Efficient Protocol with Static Clustering (EEPSC). EEPSC, partitions the network into static clusters, eliminates the overhead of dynamic clustering and utilizes temporary-cluster-heads to distribute the energy load among high-power sensor nodes; thus extends network lifetime. We have conducted simulation-based evaluations to compare the performance of EEPSC against Low-Energy Adaptive Clustering Hierarchy (LEACH). Our experiment results show that EEPSC outperforms LEACH in terms of network lifetime and power consumption minimization.
Abstract: Coarse and fine particulate matter were collected at a
residential area at Vashi, Navi Mumbai and the filter samples were
analysed for trace elements using PIXE technique. The trend of
particulate matter showed higher concentrations during winter than
the summer and monsoon concentration levels. High concentrations
of elements related to soil and sea salt were found in PM10 and
PM2.5. Also high levels of zinc and sulphur found in the particulates
of both the size fractions. EF analysis showed enrichment of Cu, Cr
and Mn only in the fine fraction suggesting their origin from
anthropogenic sources. The EF value was observed to be maximum
for As, Pb and Zn in the fine particulates. However, crustal derived
elements showed very low EF values indicating their origin from
soil. The PCA based multivariate studies identified soil, sea salt,
combustion and Se sources as common sources for coarse and
additionally an industrial source has also been identified for fine
particles.
Abstract: Design and land use are closely linked to the
energy efficiency levels for an urban area. The current city
planning practice does not involve an effective land useenergy
evaluation in its 'blueprint' urban plans. The study
proposed an appraisal method that can be embedded in GIS
programs using five planning criteria as how far a planner can
give away from the planning principles (criteria) for the most
energy output s/he can obtain. The case of Balcova, a district
in the Izmir Metropolitan area, is used conformingly for
evaluating the proposed master plan and the geothermal
energy (heating only) use for the concern district.
If the land use design were proposed accordingly at-most
energy efficiency (a 30% obtained), mainly increasing the
density around the geothermal wells and also proposing more
mixed use zones, we could have 17% distortion (infidelity to
the main planning principles) from the original plan. The
proposed method can be an effective tool for planners as
simulation media, of which calculations can be made by GIS
ready tools, to evaluate efficiency levels for different plan
proposals, letting to know how much energy saving causes
how much deviation from the other planning ideals. Lower
energy uses can be possible for different land use proposals
for various policy trials.
Abstract: This paper presents a simple and sensitive kinetic
spectrophotometric method for the determination of ramipril in
commercial dosage forms. The method is based on the reaction of the
drug with 1-chloro-2,4-dinitrobenzene (CDNB) in dimethylsulfoxide
(DMSO) at 100 ± 1ºC. The reaction is followed
spectrophotometrically by measuring the rate of change of the
absorbance at 420 nm. Fixed-time (ΔA) and equilibrium methods are
adopted for constructing the calibration curves. Both the calibration
curves were found to be linear over the concentration ranges 20 - 220
μg/ml. The regression analysis of calibration data yielded the linear
equations: Δ A = 6.30 × 10-4 + 1.54 × 10-3 C and A = 3.62 × 10-4 +
6.35 × 10-3 C for fixed time (Δ A) and equilibrium methods,
respectively. The limits of detection (LOD) for fixed time and
equilibrium methods are 1.47 and 1.05 μg/ml, respectively. The
method has been successfully applied to the determination of ramipril
in commercial dosage forms. Statistical comparison of the results
shows that there is no significant difference between the proposed
methods and Abdellatef-s spectrophotometric method.
Abstract: Tungsten trioxide has been prepared by using P-PTA
as a precursor on alumina substrates by spin coating method.
Palladium introduced on WO3 film via electrolysis deposition by
using palladium chloride as catalytic precursor. The catalytic
precursor was introduced on the series of films with different
morphologies. X-ray diffractometry (XRD), Scanning electron
microscopy (SEM) and XPS were applied to analyze structure and
morphology of the fabricated thin films. Then we measured variation
of samples- electrical conductivity of pure and Pd added films in air
and diluted hydrogen. Addition of Pd resulted in a remarkable
improvement of the hydrogen sensing properties of WO3 by detection
of Hydrogen below 1% at room temperature. Also variation of the
electrical conductivity in the presence of diluted hydrogen revealed
that response of samples depends rather strongly on the palladium
configuration on the surface.
Abstract: Wind turbines with double output induction
generators can operate at variable speed permitting conversion
efficiency maximization over a wide range of wind velocities. This
paper presents the performance analysis of a wind driven double
output induction generator (DOIG) operating at varying shafts speed.
A periodic transient state analysis of DOIG equipped with two
converters is carried out using a hybrid induction machine model.
This paper simulates the harmonic content of waveforms in various
points of drive at different speeds, based on the hybrid model
(dqabc). Then the sinusoidal and trapezoidal pulse-width–modulation
control techniques are used in order to improve the power factor of
the machine and to weaken the injected low order harmonics to the
supply. Based on the frequency spectrum, total harmonics distortion,
distortion factor and power factor. Finally advantages of sinusoidal
and trapezoidal pulse width modulation techniques are compared.
Abstract: This study aims to clarify constructions which enable to improve socio-cultural values of environments and also to obtain new knowledge on selecting development plans. CVM is adopted as a method of evaluation. As a case of the research, university campus (CP; the following) is selected on account of its various environments, institutions and many users. Investigations were conducted from 4 points of view, total value and utility value of whole CP environments, values of each environment existing in CP or development plan assumed in CP. Furthermore, respondents- attributes were also investigated. In consequence, the following is obtained. 1) Almost all of total value of CP is composed of utility value of direct use. 2) Each of environment and development plans whose value is the highest is clarified. 3) Moreover, development plan to improve environmental value the most is specified.
Abstract: Automobile Industry has great importance in the
Spanish economy (8,7 % of the active Spanish population is
employed in this sector).The above mentioned sector has been one of
the principal sectors affected by the current economic crisis,
consistently, the budgets in advertising have been severely limited
(46,9 % less in the period of reference), these needs of reduction
have originated a substantial change in the advertising strategy (from
2007 the increase of the advertising investment in Internet is 251,6
%), and increase profitability. The growing use of social media by
consumers therefore makes online consumer conversations an
attractive additional format for Automobile firms to promote
products at a lower cost. This research analyzes the relation between
the activity in Social Media and the design in the car industry,
looking for relations between strategies of design based on Social
Media and sales and a channel of information for companies to know
what the consumer preferences. For this ongoing research we used a
longitudinal withdrawal of information has been used using
information of panel. Managerial and research implications of the
finding are discussed.
Abstract: This work presents a fusion of Log Gabor Wavelet
(LGW) and Maximum a Posteriori (MAP) estimator as a speech
enhancement tool for acoustical background noise reduction. The
probability density function (pdf) of the speech spectral amplitude is
approximated by a Generalized Laplacian Distribution (GLD).
Compared to earlier estimators the proposed method estimates the
underlying statistical model more accurately by appropriately
choosing the model parameters of GLD. Experimental results show
that the proposed estimator yields a higher improvement in
Segmental Signal-to-Noise Ratio (S-SNR) and lower Log-Spectral
Distortion (LSD) in two different noisy environments compared to
other estimators.