Abstract: to simulate the phenomenon of electronic transport in semiconductors, we try to adapt a numerical method, often and most frequently it’s that of Monte Carlo. In our work, we applied this method in the case of a ternary alloy semiconductor GaInP in its cubic form; The Calculations are made using a non-parabolic effective-mass energy band model. We consider a band of conduction to three valleys (ΓLX), major of the scattering mechanisms are taken into account in this modeling, as the interactions with the acoustic phonons (elastic collisions) and optics (inelastic collisions). The polar optical phonons cause anisotropic collisions, intra-valleys, very probable in the III-V semiconductors. Other optical phonons, no polar, allow transitions inter-valleys. Initially, we present the full results obtained by the simulation of Monte Carlo in GaInP in stationary regime. We consider thereafter the effects related to the application of an electric field varying according to time, we thus study the transient phenomenon which make their appearance in ternary material
Abstract: The use of synthetic retardants in polymeric insulated
cables is not uncommon in the high voltage engineering to study
electrical treeing phenomenon. However few studies on organic
materials for the same investigation have been carried. .This paper
describes the study on the effects of Oil Palm Empty Fruit Bunch
(OPEFB) microfiller on the tree initiation and propagation in silicone
rubber with different weight percentages (wt %) of filler to insulation
bulk material. The weight percentages used were 0 wt % and 1 wt %
respectively. It was found that the OPEFB retards the propagation of
the electrical treeing development. For tree inception study, the
addition of 1(wt %) OPEFB has increase the tree inception voltage of
silicone rubber. So, OPEFB is a potential retardant to the initiation
and growth of electrical treeing occurring in polymeric materials for
high voltage application. However more studies on the effects of
physical and electrical properties of OPEFB as a tree retardant
material are required.
Abstract: Circular knitting machine makes the fabric with more than two knitting tools. Variation of yarn tension between different knitting tools causes different loop length of stitches duration knitting process. In this research, a new intelligent method is applied to control loop length of stitches in various tools based on ideal shape of stitches and real angle of stitches direction while different loop length of stitches causes stitches deformation and deviation those of angle. To measure deviation of stitch direction against variation of tensions, image processing technique was applied to pictures of different fabrics with constant front light. After that, the rate of deformation is translated to needed compensation of loop length cam degree to cure stitches deformation. A fuzzy control algorithm was applied to loop length modification in knitting tools. The presented method was experienced for different knitted fabrics of various structures and yarns. The results show that presented method is useable for control of loop length variation between different knitting tools based on stitch deformation for various knitted fabrics with different fabric structures, densities and yarn types.
Abstract: Protein-protein interactions (PPI) play a crucial role in many biological processes such as cell signalling, transcription, translation, replication, signal transduction, and drug targeting, etc. Structural information about protein-protein interaction is essential for understanding the molecular mechanisms of these processes. Structures of protein-protein complexes are still difficult to obtain by biophysical methods such as NMR and X-ray crystallography, and therefore protein-protein docking computation is considered an important approach for understanding protein-protein interactions. However, reliable prediction of the protein-protein complexes is still under way. In the past decades, several grid-based docking algorithms based on the Katchalski-Katzir scoring scheme were developed, e.g., FTDock, ZDOCK, HADDOCK, RosettaDock, HEX, etc. However, the success rate of protein-protein docking prediction is still far from ideal. In this work, we first propose a more practical measure for evaluating the success of protein-protein docking predictions,the rate of first success (RFS), which is similar to the concept of mean first passage time (MFPT). Accordingly, we have assessed the ZDOCK bound and unbound benchmarks 2.0 and 3.0. We also createda new benchmark set for protein-protein docking predictions, in which the complexes have experimentally determined binding affinity data. We performed free energy calculation based on the solution of non-linear Poisson-Boltzmann equation (nlPBE) to improve the binding mode prediction. We used the well-studied thebarnase-barstarsystem to validate the parameters for free energy calculations. Besides,thenlPBE-based free energy calculations were conducted for the badly predicted cases by ZDOCK and ZRANK. We found that direct molecular mechanics energetics cannot be used to discriminate the native binding pose from the decoys.Our results indicate that nlPBE-based calculations appeared to be one of the promising approaches for improving the success rate of binding pose predictions.
Abstract: We developed a multi-camera control system that a (one) cameraman can operate several cameras at a compact studio. we analyzed a workflow of a cameraman of some program shootings with two cameras and clarified their heavy tasks. The system based on a dynamic workflow which adapts a program progressing and recommends of cameraman. we perform the automation of multicamera controls by modeling of studio environment and perform automatic camera adjustment for suitable angle of view with face detection. Our experiment at a real program shooting showed that one cameraman can carry out the task of shooting sufficiently.
Abstract: The ability of pomelo peel, a natural biosorbent, to remove Cd(II) ions from aqueous solution by biosorption was investigated. The experiments were carried out by batch method at 25 °C. The influence of solution pH, initial cadmium ion concentrations and contact times were evaluated. Cadmium ion removal increased significantly as the pH of the solution increased from pH 1 to pH 5. At pH 5, the cadmium ion removal reached a maximum value. The equilibrium process was described well by the Langmuir isotherm model, with a maximum biosorption capacity of 21.83 mg/g. The biosorption was relatively quick, (approx. 20 min). Biosorption kinetics followed a pseudo-second-order model. The result showed that pomelo peel was effective as a biosorbent for removing cadmium ions from aqueous solution. It is a low cost material that shows potential to be applied in wastewater technology for remediation of heavy metal contamination.
Abstract: In this article we address the problem of mobile robot formation control. Indeed, the most work, in this domain, have studied extensively classical control for keeping a formation of mobile robots. In this work, we design an FLC (Fuzzy logic Controller) controller for separation and bearing control (SBC). Indeed, the leader mobile robot is controlled to follow an arbitrary reference path, and the follower mobile robot use the FSBC (Fuzzy Separation and Bearing Control) to keep constant relative distance and constant angle to the leader robot. The efficiency and simplicity of this control law has been proven by simulation on different situation.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: Calcium magnesium acetate (CMA) is environmentally
benign deicing chemicals that can replace sodium chloride that is
widely used on roads and highways at present for snow and ice control
to provide safe driving conditions during winter. The price of CMA
from petroleum-derived acetic acid is quite expensive. The bamboo
vinegar is the by-product from bamboo charcoal production. The
bamboo vinegar was used to prepare calcium acetate as raw materials,
and its deicing and corrosive performances were studied in this paper.
The results show that the freezing temperature of calcium acetate is
lower than that of sodium chloride when they have same molar
concentration, the deicing performance of calcium acetate is better
than that of sodium chloride when they have same moles, while the
deicing performance of sodium chloride is better than that of calcium
acetate. The corrosion of sodium chloride on iron-nail and steel-nail is
larger than that of calcium acetate whether they have same mass
concentration or same molar concentration, and the corrosion of
sodium chloride and calcium acetate on iron-nail is larger than that on
steel-nail, and calcium acetate almost hasn't corrosion on steel-nail.
Abstract: The tensile properties of Mg-3%Al nanocrystalline
alloys were investigated at different test environment. Bulk
nanocrystalline samples of these alloy was successfully prepared by
mechanical alloying (MA) followed by cold compaction, sintering,
and hot extrusion process. The crystal size of the consolidated milled
sample was calculated by X-Ray line profile analysis. The
deformation mechanism and microstructural characteristic at
different test condition was discussed extensively. At room
temperature, relatively lower value of activation volume (AV) and
higher value of strain rate sensitivity (SRS) suggests that new rate
controlling mechanism accommodating plastic flow in the present
nanocrystalline sample. The deformation behavior and the
microstructural character of the present samples were discussed in
details.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: In this paper, the optical generation of three bands of
continuously tunable millimeter-wave signals using an optical phase
modulator (OPM) and a polarization state rotation filter (PSRF) as an
optical notch filter is analyzed. The effect of the chromatic dispersion
on millimeter-wave signals is presented.
Abstract: Two species of Physalis, P.angulataL. and P.
peruviana L. were used as models for comparative study to
understand the values of micro-morphological, -anatomical and
architectural characteristics of leaf for taxonomic purposes and
possibly breeding and commercial applications. Both speciespossess
amphistomaticleaves with 1-layer epidermis, 3-4-layer spongy
mesophyll andbicollateral bundle midrib. Palisade parenchyma cells
of P. angulatawere almost twice longer (65-75 μm) than the other
one. Type of stomata was similar as anomocyticbut stomatal
index(SI) at adaxial surface and abaxial surface of P. angulata were
less than of P. peruvianaas 3.57, 4.00 and6.25, 6.66 respectively.
Some leaf architectural characteristics such as leaf shape, order of
venationalsoprovided information of taxonomic significance
Abstract: The paper presents a numerical investigation on the
rapid gas decompression in pure nitrogen which is made by using the
one-dimensional (1D) and three-dimensional (3D) mathematical
models of transient compressible non-isothermal fluid flow in pipes.
A 1D transient mathematical model of compressible thermal multicomponent
fluid mixture flow in pipes is presented. The set of the
mass, momentum and enthalpy conservation equations for gas phase
is solved in the model. Thermo-physical properties of multicomponent
gas mixture are calculated by solving the Equation of
State (EOS) model. The Soave-Redlich-Kwong (SRK-EOS) model is
chosen. This model is successfully validated on the experimental data
[1] and shows a good agreement with measurements. A 3D transient
mathematical model of compressible thermal single-component gas
flow in pipes, which is built by using the CFD Fluent code (ANSYS),
is presented in the paper. The set of unsteady Reynolds-averaged
conservation equations for gas phase is solved. Thermo-physical
properties of single-component gas are calculated by solving the Real
Gas Equation of State (EOS) model. The simplest case of gas
decompression in pure nitrogen is simulated using both 1D and 3D
models. The ability of both models to simulate the process of rapid
decompression with a high order of agreement with each other is
tested. Both, 1D and 3D numerical results show a good agreement
between each other. The numerical investigation shows that 3D CFD
model is very helpful in order to validate 1D simulation results if the
experimental data is absent or limited.
Abstract: Combined therapy using Interferon and Ribavirin is the standard treatment in patients with chronic hepatitis C. However, the number of responders to this treatment is low, whereas its cost and side effects are high. Therefore, there is a clear need to predict patient’s response to the treatment based on clinical information to protect the patients from the bad drawbacks, Intolerable side effects and waste of money. Different machine learning techniques have been developed to fulfill this purpose. From these techniques are Associative Classification (AC) and Decision Tree (DT). The aim of this research is to compare the performance of these two techniques in the prediction of virological response to the standard treatment of HCV from clinical information. 200 patients treated with Interferon and Ribavirin; were analyzed using AC and DT. 150 cases had been used to train the classifiers and 50 cases had been used to test the classifiers. The experiment results showed that the two techniques had given acceptable results however the best accuracy for the AC reached 92% whereas for DT reached 80%.
Abstract: We discuss the convergence property of the minimum residual (MINRES) method for the solution of complex shifted Hermitian system (αI + H)x = f. Our convergence analysis shows that the method has a faster convergence than that for real shifted Hermitian system (Re(α)I + H)x = f under the condition Re(α) + λmin(H) > 0, and a larger imaginary part of the shift α has a better convergence property. Numerical experiments show such convergence properties.
Abstract: Interpolated contour maps drawn for aluminum,
copper and molybdenum in downstream monitoring boreholes of
water dam in Miduk Copper Complex and the values of pH, redox
potential (Eh) and distance from water dam indicate different trends
of variation and behavior of these three elements in downward
groundwater resources. As these maps exhibit, aluminum is dominant
in the most alkaline (pH = 9-11) borehole (MB5) to water dam. The
highest concentration of molybdenum is found in the nearest
borehole (MB6) to water dam. Main concentration of copper is
observed in the most oxidized borehole (MB3 with Eh=293.2mV).
The spatial difference among sampling stations can be attributed to
the existence of faults and diaclases in the geologic structure of
Miduk region which causes the groundwater sampling sites to be
impressed by different contamination sources (toe seepage and upper
seepage water originated from different zones of tailings dump).
Abstract: In a 10-week (May – August, 2008) Phase I trial, 840, 1+ rainbow trout, Oncorhynchus mykiss, received a commercial oral immunomodulator, Fin Immune™, at four different dosages (0, 10, 20 and 30 mg g-1) to evaluate immune response and growth. The overall objective of was to determine an optimal dosage of this product for rainbow trout that provides enhanced immunity with maximal growth and health. Biweekly blood samples were taken from 10 randomly selected fish in each tank (30 samples per treatment) to evaluate the duration of enhanced immunity conferred by Fin-Immune™. The immunological assessment included serum white blood cell (lymphocyte, neutrophil) densities and blood hematocrit (packed cell volume %). Of these three variables, only lymphocyte density increased significantly among trout fed Fin- Immune™ at 20 and 30 mg g-1 which peaked at week 6. At week 7, all trout were switched to regular feed (lacking Fin-Immune™) and by week 10, lymphocyte levels decreased among all levels but were still greater than at week 0. There was growth impairment at the highest dose of Fin-Immune™ tested (30 mg g-1) which can be associated with a physiological compensatory mechanism due to a dose-specific threshold level. Thus, our main objective of this Phase I study was achieved, the 20 mg g-1 dose of Fin-Immune™ should be the most efficacious (of those we tested) to use for a Phase II disease challenge trial.
Abstract: A method of collecting composition data and examining structural features of pearlite lamellae and the parent austenite at the growth interface in a 13wt. % manganese steel has been demonstrated with the use of Scanning Transmission Electron Microscopy (STEM). The combination of composition data and the structural features observed at the growth interface show that available theories of pearlite growth cannot explain all the observations.
Abstract: This paper focuses on systematic analysis and
controller design of the two-inertia STABILIZATION system,
considering the angular motion on a base body. This approach is
essential to the stabilization system to aim at a target under three or six
degrees of freedom base motion. Four controllers, such as
conventional PDF(Pseudo-Derivative Feedback) controller with
motor speed feedback, PDF controller with load speed feedback,
modified PDF controller with motor-load speed feedback and
feedforward controller added to modified PDF controller, are
suggested to improve reference tracking and disturbance rejection
performance. Characteristics and performance of each controller are
analyzed and validated by simulation in the case of the modified PDF
controller with and without a feedforward controller.