Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: A new hybrid method to realise high-precision
distortion determination for optical ultra-precision 3D measurement
systems based on stereo cameras using active light projection is
introduced. It consists of two phases: the basic distortion
determination and the refinement. The refinement phase of the
procedure uses a plane surface and projected fringe patterns as
calibration tools to determine simultaneously the distortion of both
cameras within an iterative procedure. The new technique may be
performed in the state of the device “ready for measurement" which
avoids errors by a later adjustment. A considerable reduction of
distortion errors is achieved and leads to considerable improvements
of the accuracy of 3D measurements, especially in the precise
measurement of smooth surfaces.
Abstract: A simple analytical model has been developed to
optimize biasing conditions for obtaining maximum linearity among
lattice-matched, pseudomorphic and metamorphic HEMT types as
well as enhancement and depletion HEMT modes. A nonlinear
current-voltage model has been simulated based on extracted data to
study and select the most appropriate type and mode of HEMT in
terms of a given gate-source biasing voltage within the device so as
to employ the circuit for the highest possible output current or
voltage linear swing. Simulation results can be used as a basis for the
selection of optimum gate-source biasing voltage for a given type
and mode of HEMT with regard to a circuit design. The
consequences can also be a criterion for choosing the optimum type
or mode of HEMT for a predetermined biasing condition.
Abstract: This paper presents a method of reducing the feedback
delay time of DWA(Data Weighted Averaging) used in sigma-delta
modulators. The delay time reduction results from the elimination of
the latch at the quantizer output and also from the falling edge
operation. The designed sigma-delta modulator improves the timing
margin about 16%. The sub-circuits of sigma-delta modulator such as
SC(Switched Capacitor) integrator, 9-level quantizer, comparator, and
DWA are designed with the non-ideal characteristics taken into
account. The sigma-delta modulator has a maximum SNR (Signal to
Noise Ratio) of 84 dB or 13 bit resolution.
Abstract: The effects of irrigation with dairy factory wastewater
on soil properties were investigated at two sites that had received
irrigation for > 60 years. Two adjoining paired sites that had never
received DFE were also sampled as well as another seven fields from
a wider area around the factory. In comparison with paired sites that
had not received effluent, long-term wastewater irrigation resulted in
an increase in pH, EC, extractable P, exchangeable Na and K and
ESP. These changes were related to the use of phosphoric acid,
NaOH and KOH as cleaning agents in the factory. Soil organic C
content was unaffected by DFE irrigation but the size (microbial
biomass C and N) and activity (basal respiration) of the soil
microbial community were increased. These increases were
attributed to regular inputs of soluble C (e.g. lactose) present as milk
residues in the wastewater. Principal component analysis (PCA) of
the soils data from all 11sites confirmed that the main effects of DFE
irrigation were an increase in exchangeable Na, extractable P and
microbial biomass C, an accumulation of soluble salts and a liming
effect. PCA analysis of soil bacterial community structure, using
PCR-DGGE of 16S rDNA fragments, generally separated individual
sites from one another but did not group them according to irrigation
history. Thus, whilst the size and activity of the soil microbial
community were increased, the structure and diversity of the
bacterial community remained unaffected.
Abstract: To create a solution for a specific problem in machine
learning, the solution is constructed from the data or by use a search
method. Genetic algorithms are a model of machine learning that can
be used to find nearest optimal solution. While the great advantage of
genetic algorithms is the fact that they find a solution through
evolution, this is also the biggest disadvantage. Evolution is inductive,
in nature life does not evolve towards a good solution but it evolves
away from bad circumstances. This can cause a species to evolve into
an evolutionary dead end. In order to reduce the effect of this
disadvantage we propose a new a learning tool (criteria) which can be
included into the genetic algorithms generations to compare the
previous population and the current population and then decide
whether is effective to continue with the previous population or the
current population, the proposed learning tool is called as Keeping
Efficient Population (KEP). We applied a GA based on KEP to the
production line layout problem, as a result KEP keep the evaluation
direction increases and stops any deviation in the evaluation.
Abstract: Water samples were collected from river Pandu at six
stations where human and animal activities were high. Composite
samples were analyzed for dissolved oxygen (DO), biochemical
oxygen demand (BOD), chemical oxygen demand (COD) , pH values
during dry and wet seasons as well as the harmattan period. The total
data points were used to establish relationships between the
parameters and data were also subjected to statistical analysis and
expressed as mean ± standard error of mean (SEM) at a level of
significance of p
Abstract: Accurate demand forecasting is one of the most key
issues in inventory management of spare parts. The problem of
modeling future consumption becomes especially difficult for lumpy
patterns, which characterized by intervals in which there is no
demand and, periods with actual demand occurrences with large
variation in demand levels. However, many of the forecasting
methods may perform poorly when demand for an item is lumpy.
In this study based on the characteristic of lumpy demand patterns
of spare parts a hybrid forecasting approach has been developed,
which use a multi-layered perceptron neural network and a
traditional recursive method for forecasting future demands. In the
described approach the multi-layered perceptron are adapted to
forecast occurrences of non-zero demands, and then a conventional
recursive method is used to estimate the quantity of non-zero
demands. In order to evaluate the performance of the proposed
approach, their forecasts were compared to those obtained by using
Syntetos & Boylan approximation, recently employed multi-layered
perceptron neural network, generalized regression neural network
and elman recurrent neural network in this area. The models were
applied to forecast future demand of spare parts of Arak
Petrochemical Company in Iran, using 30 types of real data sets. The
results indicate that the forecasts obtained by using our proposed
mode are superior to those obtained by using other methods.
Abstract: Precast concrete has been widely adopted in public
housing construction of Hong Kong since the mid-1980s. While
pre-casting is considered an environmental friendly solution, there is
lack of study to investigate the life cycle performance of precast
concrete units. This study aims to bridge the knowledge gap by
providing a comprehensive life cycle assessment (LCA) study for two
precast elements namely façade and bathroom. The results show that
raw material is the most significant contributor of environmental
impact accounting for about 90% to the total impact. Furthermore,
human health is more affected by the production of precast concrete
than the ecosystems.
Abstract: This paper presents an approach for the determination of the optimal cutting parameters (spindle speed, feed rate, depth of cut and engagement) leading to minimum surface roughness in face milling of high silicon stainless steel by coupling neural network (NN) and Electromagnetism-like Algorithm (EM). In this regard, the advantages of statistical experimental design technique, experimental measurements, artificial neural network, and Electromagnetism-like optimization method are exploited in an integrated manner. To this end, numerous experiments on this stainless steel were conducted to obtain surface roughness values. A predictive model for surface roughness is created by using a back propogation neural network, then the optimization problem was solved by using EM optimization. Additional experiments were performed to validate optimum surface roughness value predicted by EM algorithm. It is clearly seen that a good agreement is observed between the predicted values by EM coupled with feed forward neural network and experimental measurements. The obtained results show that the EM algorithm coupled with back propogation neural network is an efficient and accurate method in approaching the global minimum of surface roughness in face milling.
Abstract: In this paper comparison of Reflector Antenna
analyzing techniques based on wave and ray nature of optics is
presented for an offset reflector antenna using GRASP (General
Reflector antenna Analysis Software Package) software. The results
obtained using PO (Physical Optics), PTD (Physical theory of
Diffraction), and GTD (Geometrical Theory of Diffraction) are
compared. The validity of PO and GTD techniques in regions around
the antenna, caustic behavior of GTD in main beam, and deviation of
GTD in case of near-in sidelobes of radiation pattern are discussed.
The comparison for far-out sidelobes predicted by PO, PO + PTD
and GTD is described. The effect of Direct Radiations from feed
which results in feed selection for the system is addressed.
Abstract: We present an Electronic Nose (ENose), which is
aimed at identifying the presence of one out of two gases, possibly
detecting the presence of a mixture of the two. Estimation of the
concentrations of the components is also performed for a volatile
organic compound (VOC) constituted by methanol and acetone, for
the ranges 40-400 and 22-220 ppm (parts-per-million), respectively.
Our system contains 8 sensors, 5 of them being gas sensors (of the
class TGS from FIGARO USA, INC., whose sensing element is a tin
dioxide (SnO2) semiconductor), the remaining being a temperature
sensor (LM35 from National Semiconductor Corporation), a
humidity sensor (HIH–3610 from Honeywell), and a pressure sensor
(XFAM from Fujikura Ltd.).
Our integrated hardware–software system uses some machine
learning principles and least square regression principle to identify at
first a new gas sample, or a mixture, and then to estimate the
concentrations. In particular we adopt a training model using the
Support Vector Machine (SVM) approach with linear kernel to teach
the system how discriminate among different gases. Then we apply
another training model using the least square regression, to predict
the concentrations.
The experimental results demonstrate that the proposed
multiclassification and regression scheme is effective in the
identification of the tested VOCs of methanol and acetone with
96.61% correctness. The concentration prediction is obtained with
0.979 and 0.964 correlation coefficient for the predicted versus real
concentrations of methanol and acetone, respectively.
Abstract: The demands of taller structures are becoming imperative almost everywhere in the world in addition to the challenges of material and labor cost, project time line etc. This paper conducted a study keeping in view the challenging nature of high-rise construction with no generic rules for deflection minimizations and frequency control. The effects of cyclonic wind and provision of outriggers on 28-storey, 42-storey and 57-storey are examined in this paper and certain conclusions are made which would pave way for researchers to conduct further study in this particular area of civil engineering. The results show that plan dimensions have vital impacts on structural heights. Increase of height while keeping the plan dimensions same, leads to the reduction in the lateral rigidity. To achieve required stiffness increase of bracings sizes as well as introduction of additional lateral resisting system such as belt truss and outriggers is required.
Abstract: The development of distributed systems has been affected by the need to accommodate an increasing degree of flexibility, adaptability, and autonomy. The Mobile Agent technology is emerging as an alternative to build a smart generation of highly distributed systems. In this work, we investigate the performance aspect of agent-based technologies for information retrieval. We present a comparative performance evaluation model of Mobile Agents versus Remote Method Invocation by means of an analytical approach. We demonstrate the effectiveness of mobile agents for dynamic code deployment and remote data processing by reducing total latency and at the same time producing minimum network traffic. We argue that exploiting agent-based technologies significantly enhances the performance of distributed systems in the domain of information retrieval.
Abstract: Creative drama which interconnects with the concepts of play, theatre, animation and role playing is a field which can only be learnt and expressed through experiencing. This study about assessment of the drama teaching in preschools by children was conducted in 3 preschools in Ankara with participation of 12 children of 6 ages who had taken drama learning courses. Qualitative research approach and semi-structured interviewing technique were employed. The results of the study indicated that all of 12 children defined drama as a game and entertainment.
Abstract: As various mobile sensing technologies, remote
control and ubiquitous infrastructure are developing and expectations
on quality of life are increasing, a lot of researches and developments
on home network technologies and services are actively on going,
Until now, we have focused on how to provide users with high-level
home network services, while not many researches on home network
security for guaranteeing safety are progressing. So, in this paper, we
propose an access control model specific to home network that
provides various kinds of users with home network services up one-s
characteristics and features, and protects home network systems from
illegal/unnecessary accesses or intrusions.
Abstract: In medical therapy, laser has been widely used to conduct cosmetic, tumor and other treatments. During the process of laser irradiation, there may be thermal damage caused by excessive laser exposure. Thus, the establishment of a complete thermal analysis model is clinically helpful to physicians in reference data. In this study, porcine liver in place of tissue was subjected to laser irradiation to set up the experimental data considering the explored impact on surface thermal field and thermal damage region under different conditions of power, laser irradiation time, and distance between laser and porcine liver. In the experimental process, the surface temperature distribution of the porcine lever was measured by the infrared thermal imager. In the part of simulation, the bio heat transfer Pennes-s equation was solved by software SYSWELD applying in welding process. The double ellipsoid function as a laser source term is firstly considered in the prediction for surface thermal field and internal tissue damage. The simulation results are compared with the experimental data to validate the mathematical model established here in.
Abstract: This study include the effect of strain and storage
period and their interaction on some quantitative and qualitative traits
and percentages of the egg components in the eggs collected at the
start of production (at age 24 weeks). Eggs were divided into three
storage periods (1, 7 and 14) days under refrigerator temperature (5-
7)0C. Fifty seven eggs obtained randomly from each strain including
Isa Brown and Lohman White. General Linear Model within
SAS programme was used to analyze the collected data
and correlations between the studied traits were calculated for each
strain.Average egg weight (EW), Haugh Unit (HU), yolk index (YI),
yolk % (HP), albumin % (AP) and yolk to albumin ratio (YAR) was
56.629 gm, 87.968 %, 0.493, 22.13%, 67.74% and 32.76
respectively. Egg produced from ISA Brown surpassed those
produced by Lohman White significantly (P
Abstract: In this paper the effects of top management commitment on knowledge management activities has been analyzed. This research has been conducted as a case study in an academic environment. The data collection was carried out in the form of semi-structured interview with an interview guide. This study shows the effects of knowledge management strategic plan developing in academia strategic plan on knowledge management success. This paper shows the importance top management commitment factors including strategic plan, communication, and training on knowledge management success in academia. In particular the most important role of Strategic planning in knowledge management success is clarified. This study explores one of the necessary organizational infrastructures of successful implementation of knowledge management. The idea of this research could be applied in the other context especially in the industrial organizations.
Abstract: The paper presents a novel method for the 3D shaping
of different materials using a high-pressure abrasive water jet and a
flat target image. For steering movement process of the jet a principle
similar to raster image way of record and readout was used.
However, respective colors of pixel of such a bitmap are connected
with adequate jet feed rate that causes erosion of material with
adequate depth. Thanks to that innovation, one can observe spatial
imaging of the object. Theoretical basis as well as spatial model of
material shaping and experimental stand including steering program
are presented in. There are also presented methodic and some
experimental erosion results as well as practical example of object-s
bas-relief made of metal.