Abstract: This paper explores the implementation of adaptive
coding and modulation schemes for Multiple-Input Multiple-Output
Orthogonal Frequency Division Multiplexing (MIMO-OFDM) feedback
systems. Adaptive coding and modulation enables robust and
spectrally-efficient transmission over time-varying channels. The basic
premise is to estimate the channel at the receiver and feed this estimate
back to the transmitter, so that the transmission scheme can be
adapted relative to the channel characteristics. Two types of codebook
based channel feedback techniques are used in this work. The longterm
and short-term CSI at the transmitter is used for efficient channel
utilization. OFDM is a powerful technique employed in communication
systems suffering from frequency selectivity. Combined with
multiple antennas at the transmitter and receiver, OFDM proves to be
robust against delay spread. Moreover, it leads to significant data rates
with improved bit error performance over links having only a single
antenna at both the transmitter and receiver. The coded modulation
increases the effective transmit power relative to uncoded variablerate
variable-power MQAM performance for MIMO-OFDM feedback
system. Hence proposed arrangement becomes an attractive approach
to achieve enhanced spectral efficiency and improved error rate
performance for next generation high speed wireless communication
systems.
Abstract: Contrary to negative emotion regulation, coping with
positive moods have received less attention in adolescent adjustment.
However, some research has found that everyone is different on
dealing with their positive emotions, which affects their adaptation
and well-being. The purpose of the present study was to investigate
the relationship between positive emotions dampening and
internalizing behavior problems of adolescent in Taiwan. A survey
was conducted and 208 students (12 to14 years old) completed the
strengths and difficulties questionnaire (SDQ), the Affect Intensity
Measure, and the positive emotions dampening scale. Analysis
methods such as descriptive statistics, t-test, Pearson correlations and
multiple regression were adapted. The results were as follows:
Emotionality and internalizing problem behavior have significant
gender differences. Compared to boys, girls have a higher score on
negative emotionality and are at a higher risk for internalizing
symptoms. However, there are no gender differences on positive
emotion dampening. Additionally, in the circumstance that negative
emotionality acted as the control variable, positive emotion
dampening strategy was (positive) related to internalizing behavior
problems. Given the results of this study, it is suggested that coaching
deconstructive positive emotion strategies is to assist adolescents
with internalizing behavior problems is encouraged.
Abstract: This paper presents the modeling and simulation of a hybrid proton exchange membrane fuel cell (PEMFC) with an energy storage system for use in a stand-alone distributed generation (DG) system. The simulation model consists of fuel cell DG, lead-acid battery, maximum power point tracking and power conditioning unit which is modeled in the MATLAB/Simulink platform. Poor loadfollowing characteristics and slow response to rapid load changes are some of the weaknesses of PEMFC because of the gas processing reaction and the fuel cell dynamics. To address the load-tracking issues in PEMFC, a hybrid PEMFC and battery storage system is considered and modelled. The model utilizes PEMFC as the main energy source whereas the battery functions as energy storage to compensate for the limitations of PEMFC.Simulation results are given to show the overall system performance under light and heavyloading conditions.
Abstract: Mobile Learning (M-Learning) is a new technology
which is to enhance current learning practices and activities for all
people especially students and academic practitioners UTP is
currently, implemented two types of learning styles which are
conventional and electronic learning. In order to improve current
learning approaches, it is necessary for UTP to implement m-learning
in UTP. This paper presents a study on the students- perceptions on
mobile utilization in the learning practices in UTP. Besides, this
paper also presents a survey that was conducted among 82 students
from System Analysis and Design (SAD) course in UTP. The survey
includes basic information of mobile devices that have been used by
the students, opinions on current learning practices and also the
opinions regarding the m-learning implementation in the current
learning practices especially in SAD course. Based on the results of
the survey, majority of the students are using the mobile devices that
can support m-learning environment. Other than that, students also
agreed that current learning practices are ineffective and they believe
that m-learning utilization can improve the effectiveness of current
learning practices.
Abstract: A number of previous studies were rarely considered
the effects of transient non-uniform balloon expansion on evaluation
of the properties and behaviors of stents during stent expansion, nor
did they determine parameters to maximize the performances driven
by mechanical characteristics. Therefore, in order to fully understand
the mechanical characteristics and behaviors of stent, it is necessary to
consider a realistic modeling of transient non-uniform balloon-stent
expansion. The aim of the study is to propose design parameters
capable of improving the ability of vascular stent through a
comparative study of seven commercial stents using finite element
analyses of a realistic transient non-uniform balloon-stent expansion
process. In this study, seven representative commercialized stents were
evaluated by finite element (FE) analysis in terms of the criteria based
on the itemized list of Food and Drug Administration (FDA) and
European Standards (prEN). The results indicate that using stents
composed of opened unit cells connected by bend-shaped link
structures and controlling the geometrical and morphological features
of the unit cell strut or the link structure at the distal ends of stent may
improve mechanical characteristics of stent. This study provides a
better method at the realistic transient non-uniform balloon-stent
expansion by investigating the characteristics, behaviors, and
parameters capable of improving the ability of vascular stent.
Abstract: Thermal conductivity is an important characteristic of
a nanofluid in laminar flow heat transfer. This paper presents an
improved model for the prediction of the effective thermal
conductivity of nanofluids based on dimensionless groups. The
model expresses the thermal conductivity of a nanofluid as a function
of the thermal conductivity of the solid and liquid, their volume
fractions and particle size. The proposed model includes a parameter
which accounts for the interfacial shell, brownian motion, and
aggregation of particle. The validation of the model is verified by
applying the results obtained by the experiments of Tio2-water and
Al2o3-water nanofluids.
Abstract: The tubes in an Ammonia primary reformer furnace
operate close to the limits of materials technology in terms of the
stress induced as a result of very high temperatures, combined with
large differential pressures across the tube wall. Operation at tube
wall temperatures significantly above design can result in a rapid
increase in the number of tube failures, since tube life is very
sensitive to the absolute operating temperature of the tube. Clearly it
is important to measure tube wall temperatures accurately in order to
prevent premature tube failure by overheating.. In the present study,
the catalyst tubes in an Ammonia primary reformer has been modeled
taking into consideration heat, mass and momentum transfer as well
as reformer characteristics.. The investigations concern the effects of
tube characteristics and superficial tube wall temperatures on of the
percentage of heat flux, unconverted methane and production of
Hydrogen for various values of steam to carbon ratios. The results
show the impact of catalyst tubes length and diameters on the
performance of operating parameters in ammonia primary reformers.
Abstract: A two-parameter fatigue model explicitly accounting for the cyclic as well as the mean stress was used to fit static and fatigue data available in literature concerning carbon fiber reinforced composite laminates subjected tension-tension fatigue. The model confirms the strength–life equal rank assumption and predicts reasonably the probability of failure under cyclic loading. The model parameters were found by best fitting procedures and required a minimum of experimental tests.
Abstract: In this paper, a simple microfluidic device for monitoring algal cell behavior is proposed. An array of algal microwells is fabricated by PDMS soft-lithography using X-ray LIGA mold, placed on a glass substrate. Two layers of replicated PDMS and substrate are attached by oxygen plasma bonding, creating a microchannel for the microfluidic system. Algal cell are loaded into the microfluidic device, which provides positive charge on the bottom surface of wells. Algal cells, which are negative charged, can be attracted to the bottom of the wells via electrostatic interaction. By varying the concentration of algal cells in the loading suspension, it is possible to obtain wells with a single cell. Liquid medium for cells monitoring are flown continuously over the wells, providing nutrient and waste exchange between the well and the main flow. This device could lead to the uncovering of the quantitative biology of the algae, which is a key to effective and extensive algal utilizations in the field of biotechnology, food industry and bioenergy research and developments.
Abstract: In this study, a vibration analysis was carried out of
symmetric angle-ply laminated composite plates with and without
square hole when subjected to compressive loads, numerically. A
buckling analysis is also performed to determine the buckling load of
laminated plates. For each fibre orientation, the compression load is
taken equal to 50% of the corresponding buckling load. In the
analysis, finite element method (FEM) was applied to perform
parametric studies, the effects of degree of orthotropy and stacking
sequence upon the fundamental frequencies and buckling loads are
discussed. The results show that the presence of a constant
compressive load tends to reduce uniformly the natural frequencies
for materials which have a low degree of orthotropy. However, this
reduction becomes non-uniform for materials with a higher degree of
orthotropy.
Abstract: This paper describes a newly designed decentralized
nonlinear control strategy to control a robot manipulator. Based on the
concept of the nonlinear state feedback theory and decentralized
concept is developed to improve the drawbacks in previous works
concerned with complicate intelligent control and low cost effective
sensor. The control methodology is derived in the sense of Lyapunov
theorem so that the stability of the control system is guaranteed. The
decentralized algorithm does not require other joint angle and velocity
information. Individual Joint controller is implemented using a digital
processor with nearly actuator to make it possible to achieve good
dynamics and modular. Computer simulation result has been
conducted to validate the effectiveness of the proposed control scheme
under the occurrence of possible uncertainties and different reference
trajectories. The merit of the proposed control system is indicated in
comparison with a classical control system.
Abstract: Paced Auditory Serial Addition Test (PASAT) has
been used as a common research tool for different neurological
disorders like Multiple Sclerosis. Recently, technology let
researchers to introduce a new versions of the visual test, the paced
visual serial addition test (PVSAT). In this paper, the computerized
version of these two tests is introduced. Beside the number of true
responses are interpreted, the reaction time of subjects are calculated
by the software. We hypothesize that paying attention to the reaction
time may be valuable. For this purpose, sixty eight female normal
subjects and fifty eight male normal subjects are enrolled in the
study. We investigate the similarity between the PASAT3 and
PVSAT3 in number of true responses and the new criterion (the
average reaction time of each subject). The similarity between two
tests were rejected (p-value = 0.000) which means that these two test
differ. The effect of sex in the tests were not approved since the pvalues
of different between PASAT3 and PVSAT3 in both sex is the
same (p-value = 0.000) which means that male and female subjects
performed the tests at no different level of performance. The new
criterion shows a negative correlation with the age which offers aged
normal subjects may have the same number of true responses as the
young subjects but they have latent responses. This will give prove
for the importance of reaction time.
Abstract: The noteworthy point in the advancement of Brain Machine Interface (BMI) research is the ability to accurately extract features of the brain signals and to classify them into targeted control action with the easiest procedures since the expected beneficiaries are of disabled. In this paper, a new feature extraction method using the combination of adaptive band pass filters and adaptive autoregressive (AAR) modelling is proposed and applied to the classification of right and left motor imagery signals extracted from the brain. The introduction of the adaptive bandpass filter improves the characterization process of the autocorrelation functions of the AAR models, as it enhances and strengthens the EEG signal, which is noisy and stochastic in nature. The experimental results on the Graz BCI data set have shown that by implementing the proposed feature extraction method, a LDA and SVM classifier outperforms other AAR approaches of the BCI 2003 competition in terms of the mutual information, the competition criterion, or misclassification rate.
Abstract: Prickly pear (Opuntia spp) fruit has received renewed
interest since it contains a betalain pigment that has an attractive
purple colour for the production of juice. Prickly pear juice was
prepared by homogenizing the fruit and treating the pulp with 48 g of
pectinase from Aspergillus niger. Titratable acidity was determined
by diluting 10 ml prickly pear juice with 90 ml deionized water and
titrating to pH 8.2 with 0.1 N NaOH. Brix was measured using a
refractometer and ascorbic acid content assayed
spectrophotometrically. Colour variation was determined
colorimetrically (Hunter L.a.b.). Hunter L.a.b. analysis showed that
the red purple colour of prickly pear juice had been affected by juice
treatments. This was indicated by low light values of colour
difference meter (CDML*), hue, CDMa* and CDMb* values. It was
observed that non-treated prickly pear juice had a high (colour
difference meter of light) CDML* of 3.9 compared to juice
treatments (range 3.29 to 2.14). The CDML* significantly (p
Abstract: The new architecture for quantum cellular
automata is offered. A QCA cell includes two layers nc-Si,
divided by a dielectric. Among themselves cells are connected
by the bridge from a conductive material. The comparison is
made between this and QCA, offered earlier by C. Lent's
group.
Abstract: The paper deals with the possibilities of modelling
vapour propagation of explosive substances in the FLUENT
software. With regard to very low tensions of explosive substance
vapours the experiment has been verified as exemplified by
mononitrotoluene. Either constant or time variable meteorological
conditions have been used for calculation. Further, it has been
verified that the eluent source may be time-dependent and may reflect
a real situation or the liberation rate may be constant. The execution
of the experiment as well as evaluation were clear and it could also
be used for modelling vapour and aerosol propagation of selected
explosive substances in the atmospheric boundary layer.
Abstract: Nowadays in applications of renewable energy sources
it is important to develop powerful and energy-saving photovoltaic
converters and to keep the prescriptions of the standards. In grid
connected PV converters the obvious solution to increase the
efficiency is to reduce the switching losses. Our new developed
control method reduces the switching losses and keeps the limitations
of the harmonic distortion standards. The base idea of the method is
the utilization of 3-state control causing discontinuous current mode
at low input power. In the following sections the control theory, the
realizations and the simulation results are presented.
Abstract: Restoration of endodontically treated teeth is a
common problem in dentistry, related to the fractures occurring in
such teeth and to concentration of forces little information regarding
variation of basic preparation guidelines in stress distribution has
been available. To date, there is still no agreement in the literature
about which material or technique can optimally restore
endodontically treated teeth. The aim of the present study was to
evaluate the influence of the core height and restoration materials on
corono-radicular restored upper first premolar. The first step of the
study was to achieve 3D models in order to analyze teeth, dowel and
core restorations and overlying full ceramic crowns. The FEM model
was obtained by importing the solid model into ANSYS finite
element analysis software. An occlusal load of 100 N was conducted,
and stresses occurring in the restorations, and teeth structures were
calculated. Numerical simulations provide a biomechanical
explanation for stress distribution in prosthetic restored teeth. Within
the limitations of the present study, it was found that the core height
has no important influence on the stress generated in coronoradicular
restored premolars. It can be drawn that the cervical regions
of the teeth and restorations were subjected to the highest stress
concentrations.
Abstract: Diagnostic and detection of the arterial stiffness is
very important; which gives indication of the associated increased risk of cardiovascular diseases. To make a cheap and easy method for general screening technique to avoid the future cardiovascular
complexes , due to the rising of the arterial stiffness ; a proposed algorithm depending on photoplethysmogram to be used. The
photoplethysmograph signals would be processed in MATLAB. The
signal will be filtered, baseline wandering removed, peaks and
valleys detected and normalization of the signals should be achieved
.The area under the catacrotic phase of the photoplethysmogram
pulse curve is calculated using trapezoidal algorithm ; then will used
in cooperation with other parameters such as age, height, blood
pressure in neural network for arterial stiffness detection. The Neural
network were implemented with sensitivity of 80%, accuracy 85%
and specificity of 90% were got from the patients data. It is
concluded that neural network can detect the arterial STIFFNESS
depending on risk factor parameters.
Abstract: Land with low pH soil spread widely in Indonesia
can be used for soybean (Glycine max) cultivation, however the
production is low. The use of acid tolerant soybean and acidaluminium
tolerant nitrogen-fixing bacteria formula was an
alternative way to increase soybean productivity on acid soils.
Bradyrhizobium japonicum is one of the nitrogen fixing bacteria
which can symbiose with soybean plants through root nodule
formation. Most of the nitrogen source required by soybean plants
can be provided by this symbiosis. This research was conducted to
study the influence of acid-aluminium tolerant B. japonicum strain
BJ 11 formula using peat as carrier on growth of Tanggamus and
Anjasmoro cultivar soybean planted on acid soil fields (pH 5.0-
5.5). The results showed that the inoculant was able to increase the
growth and production of soybean which were grown on fields acid
soil at Sukadana (Lampung) and Tanah Laut (South Kalimantan),
Indonesia.