Abstract: Heat transfer due to forced convection of copper water
based nanofluid has been predicted by Artificial Neural network
(ANN). The present nanofluid is formed by mixing copper
nanoparticles in water and the volume fractions are considered here
are 0% to 15% and the Reynolds number are kept constant at 100.
The back propagation algorithm is used to train the network. The
present ANN is trained by the input and output data which has been
obtained from the numerical simulation, performed in finite volume
based Computational Fluid Dynamics (CFD) commercial software
Ansys Fluent. The numerical simulation based results are compared
with the back propagation based ANN results. It is found that the
forced convection heat transfer of water based nanofluid can be
predicted correctly by ANN. It is also observed that the back
propagation ANN can predict the heat transfer characteristics of
nanofluid very quickly compared to standard CFD method.
Abstract: This paper presents a numerical investigation of two
horizontally mounted four-lobed swirl pipes in terms of swirl
induction effectiveness into flows passing through them. The swirl
flows induced by the two swirl pipes have the potential to improve
the efficiency of Clean-In-Place procedures in a closed processing
system by local intensification of hydrodynamic impact on the
internal pipe surface. Pressure losses, swirl development within the
two swirl pipe, swirl induction effectiveness, swirl decay and wall
shear stress variation downstream of two swirl pipes are analyzed and
compared. It was found that a shorter length of swirl inducing pipe
used in joint with transition pipes is more effective in swirl induction
than when a longer one is used, in that it has a less constraint to the
induced swirl and results in slightly higher swirl intensity just
downstream of it with the expense of a smaller pressure loss. The
wall shear stress downstream of the shorter swirl pipe is also slightly
larger than that downstream of the longer swirl pipe due to the
slightly higher swirl intensity induced by the shorter swirl pipe. The
advantage of the shorter swirl pipe in terms of swirl induction is more
significant in flows with a larger Reynolds Number.
Abstract: To understand the friction stir welding process, it is
very important to know the nature of the material flow in and around
the tool. The process is a combination of both thermal as well as
mechanical work i.e. it is a coupled thermo-mechanical process.
Numerical simulations are very much essential in order to obtain a
complete knowledge of the process as well as the physics underlying
it. In the present work a model based approach is adopted in order to
study material flow. A thermo-mechanical based CFD model is
developed using a Finite Element package, Comsol Multiphysics.
The fluid flow analysis is done. The model simultaneously predicts
shear strain fields, shear strain rates and shear stress over the entire
workpiece for the given conditions. The flow fields generated by the
streamline plot give an idea of the material flow. The variation of
dynamic viscosity, velocity field and shear strain fields with various
welding parameters is studied. Finally the result obtained from the
above mentioned conditions is discussed elaborately and concluded.
Abstract: This paper analyses the heat transfer performance and
fluid flow using different nanofluids in a square enclosure. The
energy equation and Navier-Stokes equation are solved numerically
using finite volume scheme. The effect of volume fraction
concentration on the enhancement of heat transfer has been studied
icorporating the Brownian motion; the influence of effective thermal
conductivity on the enhancement was also investigated for a range of
volume fraction concentration. The velocity profile for different
Rayleigh number. Water-Cu, water AL2O3 and water-TiO2 were
tested.
Abstract: In the Hierarchical Temporal Memory (HTM) paradigm
the effect of overlap between inputs on the activation of columns in
the spatial pooler is studied. Numerical results suggest that similar
inputs are represented by similar sets of columns and dissimilar inputs
are represented by dissimilar sets of columns. It is shown that the
spatial pooler produces these results under certain conditions for
the connectivity and proximal thresholds. Following the discussion
of the initialization of parameters for the thresholds, corresponding
qualitative arguments about the learning dynamics of the spatial
pooler are discussed.
Abstract: An efficient remanufacturing network lead to an
efficient design of sustainable manufacturing enterprise. In
remanufacturing network, products are collected from the customer
zone, disassembled and remanufactured at a suitable remanufacturing
facility. In this respect, another issue to consider is how the returned
product to be remanufactured, in other words, what is the best layout
for such facility. In order to achieve a sustainable manufacturing
system, Cellular Manufacturing System (CMS) designs are highly
recommended, CMSs combine high throughput rates of line layouts
with the flexibility offered by functional layouts (job shop).
Introducing the CMS while designing a remanufacturing network will
benefit the utilization of such a network. This paper presents and
analyzes a comprehensive mathematical model for the design of
Dynamic Cellular Remanufacturing Systems (DCRSs). In this paper,
the proposed model is the first one to date that considers CMS and
remanufacturing system simultaneously. The proposed DCRS model
considers several manufacturing attributes such as multi period
production planning, dynamic system reconfiguration, duplicate
machines, machine capacity, available time for workers, worker
assignments, and machine procurement, where the demand is totally
satisfied from a returned product. A numerical example is presented
to illustrate the proposed model.
Abstract: Hypersonic flows around spatial vehicles during their reentry phase in planetary atmospheres are characterized by intense aerothermodynamics phenomena. The aim of this work is to analyze high temperature flows around an axisymmetric blunt body taking into account chemical and vibrational non-equilibrium for air mixture species and the no slip condition at the wall. For this purpose, the Navier-Stokes equations system is resolved by the finite volume methodology to determine the flow parameters around the axisymmetric blunt body especially at the stagnation point and in the boundary layer along the wall of the blunt body. The code allows the capture of shock wave before a blunt body placed in hypersonic free stream. The numerical technique uses the Flux Vector Splitting method of Van Leer. CFL coefficient and mesh size level are selected to ensure the numerical convergence.
Abstract: Heat transfer of leaves is a crucial factor in optimal
operation of metabolic functions in plants. In order to quantify this
phenomenon in different leaves and investigate the influence of leaf
shape on heat transfer, natural convection for pine, orange and olive
leaves was simulated as representatives of different groups of leaf
shapes. CFD techniques were used in this simulation with the
purpose to calculate heat transfer of leaves in similar environmental
conditions. The problem was simulated for steady state and threedimensional
conditions. From obtained results, it was concluded that
heat fluxes of all three different leaves are almost identical, however,
total rate of heat transfer have highest and lowest values for orange
leaves, and pine leaves, respectively.
Abstract: In this research numerical simulations are performed,
using the multi-relaxation-time lattice Boltzmann method, in the
range 3 ≤ β = w[d] ≤ 30 at Re = 100, 200 and 300, where β the
blockage ratio, w is the equispaced distance between centers of
cylinders, d is the diameter of the cylinder and Re is the Reynolds
number, respectively. Special attention is paid to the effect of the
equispaced distance between centers of cylinders. Visualization of
the vorticity contour visualization are presented for some simulation
showing the flow dynamics and patterns for blockage effect. Results
show that the drag and mean drag coefficients, and Strouhal number,
in general, decrease with the increase of β for fixed Re. It is found
that the decreasing rate of drag and mean drag coefficients and
Strouhal number is more distinct in the range 3 ≤ β ≤ 15. We found
that when β > 15, the blockage effect almost diminishes. Our results
further indicate that the drag and mean drag coefficients, peak value
of the lift coefficient, root-mean-square value of the lift and drag
coefficients and the ratio between lift and drag coefficients decrease
with the increase of Re. The results indicate that symmetry boundary
condition have more blockage effect as compared to periodic
boundary condition.
Abstract: We evaluate the performance of a numerical method
for global optimization of expensive functions. The method is using a
response surface to guide the search for the global optimum. This
metamodel could be based on radial basis functions, kriging, or a
combination of different models. We discuss how to set the cyclic
parameters of the optimization method to get a balance between local
and global search. We also discuss the eventual problem with Runge
oscillations in the response surface.
Abstract: One of the main challenges in using the Discrete
Element Method (DEM) is to specify the correct input parameter
values. In general, the models are sensitive to the input parameter
values and accurate results can only be achieved if the correct values
are specified. For the linear contact model, micro-parameters such as
the particle density, stiffness, coefficient of friction, as well as the
particle size and shape distributions are required. There is a need for
a procedure to accurately calibrate these parameters before any
attempt can be made to accurately model a complete bulk materials
handling system. Since DEM is often used to model applications in
the mining and quarrying industries, a calibration procedure was
developed for materials that consist of relatively large (up to 40 mm
in size) particles. A coarse crushed aggregate was used as the test
material. Using a specially designed large shear box with a diameter
of 590 mm, the confined Young’s modulus (bulk stiffness) and
internal friction angle of the material were measured by means of the
confined compression test and the direct shear test respectively. DEM
models of the experimental setup were developed and the input
parameter values were varied iteratively until a close correlation
between the experimental and numerical results was achieved. The
calibration process was validated by modelling the pull-out of an
anchor from a bed of material. The model results compared well with
experimental measurement.
Abstract: In this paper, an analytical simplified method for
calculating elasto-plastic stresses strains of notched bodies subject to
non-proportional loading paths is discussed. The method was based
on the Neuber notch correction, which relates the incremental elastic
and elastic-plastic strain energy densities at the notch root and the
material constitutive relationship. The validity of the method was
presented by comparing computed results of the proposed model
against finite element numerical data of notched shaft. The
comparison showed that the model estimated notch-root elasto-plastic
stresses strains with good accuracy using linear-elastic stresses. The
prosed model provides more efficient and simple analysis method
preferable to expensive experimental component tests and more
complex and time consuming incremental non-linear FE analysis.
The model is particularly suitable to perform fatigue life and fatigue
damage estimates of notched components subjected to nonproportional
loading paths.
Abstract: This paper shows in detail the mathematical model of
direct and inverse kinematics for a robot manipulator (welding type)
with four degrees of freedom. Using the D-H parameters, screw
theory, numerical, geometric and interpolation methods, the
theoretical and practical values of the position of robot were
determined using an optimized algorithm for inverse kinematics
obtaining the values of the particular joints in order to determine the
virtual paths in a relatively short time.
Abstract: An Australian manufacturer has fabricated an
innovative GFRP sandwich panel made from E-glass fiber skin and a
modified phenolic core for structural applications. Debonding, which
refers to separation of skin from the core material in composite
sandwiches, is one of the most common types of damage in
composites. The presence of debonding is of great concern because it
not only severely affects the stiffness but also modifies the dynamic
behaviour of the structure. Generally it is seen that the majority of
research carried out has been concerned about the delamination of
laminated structures whereas skin-core debonding has received
relatively minor attention. Furthermore it is observed that research
done on composite slabs having multiple skin-core debonding is very
limited. To address this gap, a comprehensive research investigating
dynamic behaviour of composite panels with single and multiple
debonding is presented. The study uses finite-element modelling and
analyses for investigating the influence of debonding on free
vibration behaviour of single and multilayer composite sandwich
panels. A broad parametric investigation has been carried out by
varying debonding locations, debonding sizes and support conditions
of the panels in view of both single and multiple debonding.
Numerical models were developed with Strand7 finite element
package by innovatively selecting the suitable elements to diligently
represent their actual behavior. Three-dimensional finite element
models were employed to simulate the physically real situation as
close as possible, with the use of an experimentally and numerically
validated finite element model. Comparative results and conclusions
based on the analyses are presented. For similar extents and locations
of debonding, the effect of debonding on natural frequencies appears
greatly dependent on the end conditions of the panel, giving greater
decrease in natural frequency when the panels are more restrained.
Some modes are more sensitive to debonding and this sensitivity
seems to be related to their vibration mode shapes. The fundamental
mode seems generally the least sensitive mode to debonding with
respect to the variation in free vibration characteristics. The results
indicate the effectiveness of the developed three dimensional finite
element models in assessing debonding damage in composite
sandwich panels.
Abstract: The present research work investigates the seismic
response of reinforced concrete (RC) frame building considering the
effect of modeling masonry infill (MI) walls. The seismic behavior of
a residential 6-storey RC frame building, considering and ignoring
the effect of masonry, is numerically investigated using response
spectrum (RS) analysis. The considered herein building is designed
as a moment resisting frame (MRF) system following the Egyptian
code (EC) requirements. Two developed models in terms of bare
frame and infill walls frame are used in the study. Equivalent
diagonal strut methodology is used to represent the behavior of infill
walls, whilst the well-known software package ETABS is used for
implementing all frame models and performing the analysis. The
results of the numerical simulations such as base shear,
displacements, and internal forces for the bare frame as well as the
infill wall frame are presented in a comparative way. The results of
the study indicate that the interaction between infill walls and frames
significantly change the responses of buildings during earthquakes
compared to the results of bare frame building model. Specifically,
the seismic analysis of RC bare frame structure leads to
underestimation of base shear and consequently damage or even
collapse of buildings may occur under strong shakings. On the other
hand, considering infill walls significantly decrease the peak floor
displacements and drifts in both X and Y-directions.
Abstract: Reflux condensation occurs in vertical channels and tubes when there is an upward core flow of vapour (or gas-vapour mixture) and a downward flow of the liquid film. The understanding of this condensation configuration is crucial in the design of reflux condensers, distillation columns, and in loss-of-coolant safety analyses in nuclear power plant steam generators. The unique feature of this flow is the upward flow of the vapour-gas mixture (or pure vapour) that retards the liquid flow via shear at the liquid-mixture interface. The present model solves the full, elliptic governing equations in both the film and the gas-vapour core flow. The computational mesh is non-orthogonal and adapts dynamically the phase interface, thus produces a sharp and accurate interface. Shear forces and heat and mass transfer at the interface are accounted for fundamentally. This modeling is a big step ahead of current capabilities by removing the limitations of previous reflux condensation models which inherently cannot account for the detailed local balances of shear, mass, and heat transfer at the interface. Discretisation has been done based on finite volume method and co-located variable storage scheme. An in-house computer code was developed to implement the numerical solution scheme. Detailed results are presented for laminar reflux condensation from steam-air mixtures flowing in vertical parallel plate channels. The results include velocity and gas mass fraction profiles, as well as axial variations of film thickness.
Abstract: A numerical model has been developed to investigate the thermally triggered release kinetics for drug delivery using phase change material as shell of microcapsules. Biocompatible material n-Eicosane is used as demonstration. PCM shell of microcapsule will remain in solid form after the drug is taken, so the drug will be encapsulated by the shell, and will not be released until the target body part of lesion is exposed to external heat source, which will thermally trigger the release kinetics, leading to solid-to-liquid phase change. The findings can lead to better understanding on the key effects influencing the phase change process for drug delivery applications. The facile approach to release drug from core/shell structure of microcapsule can be well integrated with organic solvent free fabrication of microcapsules, using double emulsion as template in microfluidic aqueous two phase system.
Abstract: We address a new integer frequency offset (IFO)
estimation scheme with an aid of a pilot for orthogonal frequency
division multiplexing systems. After correlating each continual pilot
with a predetermined scattered pilot, the correlation value is again
correlated to alleviate the influence of the timing offset. From
numerical results, it is demonstrated that the influence of the timing
offset on the IFO estimation is significantly decreased.
Abstract: This paper deals with the theoretical and numerical
investigation of magneto hydrodynamic boundary layer flow of a
nanofluid past a wedge shaped wick in heat pipe used for the cooling
of electronic components and different type of machines. To
incorporate the effect of nanoparticle diameter, concentration of
nanoparticles in the pure fluid, nanothermal layer formed around the
nanoparticle and Brownian motion of nanoparticles etc., appropriate
models are used for the effective thermal and physical properties of
nanofluids. To model the rotation of nanoparticles inside the base
fluid, microfluidics theory is used. In this investigation ethylene
glycol (EG) based nanofluids, are taken into account. The non-linear
equations governing the flow and heat transfer are solved by using a
very effective particle swarm optimization technique along with
Runge-Kutta method. The values of heat transfer coefficient are
found for different parameters involved in the formulation viz.
nanoparticle concentration, nanoparticle size, magnetic field and
wedge angle etc. It is found that, the wedge angle, presence of
magnetic field, nanoparticle size and nanoparticle concentration etc.
have prominent effects on fluid flow and heat transfer characteristics
for the considered configuration.
Abstract: This paper is concerned with knowledge representation
and extraction of fuzzy if-then rules using Interval Type-2
Context-based Fuzzy C-Means clustering (IT2-CFCM) with the aid of
fuzzy granulation. This proposed clustering algorithm is based on
information granulation in the form of IT2 based Fuzzy C-Means
(IT2-FCM) clustering and estimates the cluster centers by preserving
the homogeneity between the clustered patterns from the IT2 contexts
produced in the output space. Furthermore, we can obtain the
automatic knowledge representation in the design of Radial Basis
Function Networks (RBFN), Linguistic Model (LM), and Adaptive
Neuro-Fuzzy Networks (ANFN) from the numerical input-output data
pairs. We shall focus on a design of ANFN in this paper. The
experimental results on an estimation problem of energy performance
reveal that the proposed method showed a good knowledge
representation and performance in comparison with the previous
works.