Abstract: This paper presents a synthetic jet air blower actuated
by PZT for air blowing for air-breathing micro PEM fuel cell. The
several factors to affect the performance of air-breathing PEM fuel cell
such as air flow rate, opening ratio and cathode open type in the
cathode side were studied. Especially, an air flow rate is critical
condition to improve its performance. In this paper, we developed a
synthetic jet air blower to supply a high stoichiometric air flow. The
synthetic jet mechanism is a zero mass flux device that converts
electrical energy into the momentum. The synthetic jet actuation is
usually generated by a traditional PZT actuator, which consists of a
small cylindrical cavity, in/outlet channel and PZT diaphragms. The
flow rate of the fabricated synthetic jet air blower was 400cc/min at
550Hz and its power consumption was very low under 0.3W. The
proposed air-breathing PEM fuel cell which installed synthetic jet air
blower was higher performance and stability during continuous
operation than the air-breathing fuel cell without auxiliary device to
supply the air. The results showed that the maximum power density
was 188mW/cm2 at 400mA/cm2. This maximum power density and
durability were improved more than 40% and 20%, respectively.
Abstract: Multirate multimedia delivery applications in multihop Wireless Mesh Network (WMN) are data redundant and delay-sensitive, which brings a lot of challenges for designing efficient transmission systems. In this paper, we propose a new cross layer resource allocation scheme to minimize the receiver side distortion within the delay bound requirements, by exploring application layer Position and Value (P-V) diversity as well as the multihop Effective Capacity (EC). We specifically consider image transmission optimization here. First of all, the maximum supportable source traffic rate is identified by exploring the multihop Effective Capacity (EC) model. Furthermore, the optimal source coding rate is selected according to the P-V diversity of multirate media streaming, which significantly increases the decoded media quality. Simulation results show the proposed approach improved media quality significantly compared with traditional approaches under the same QoS requirements.
Abstract: This paper presents the modeling and simulation of a hybrid proton exchange membrane fuel cell (PEMFC) with an energy storage system for use in a stand-alone distributed generation (DG) system. The simulation model consists of fuel cell DG, lead-acid battery, maximum power point tracking and power conditioning unit which is modeled in the MATLAB/Simulink platform. Poor loadfollowing characteristics and slow response to rapid load changes are some of the weaknesses of PEMFC because of the gas processing reaction and the fuel cell dynamics. To address the load-tracking issues in PEMFC, a hybrid PEMFC and battery storage system is considered and modelled. The model utilizes PEMFC as the main energy source whereas the battery functions as energy storage to compensate for the limitations of PEMFC.Simulation results are given to show the overall system performance under light and heavyloading conditions.
Abstract: Mobile Learning (M-Learning) is a new technology
which is to enhance current learning practices and activities for all
people especially students and academic practitioners UTP is
currently, implemented two types of learning styles which are
conventional and electronic learning. In order to improve current
learning approaches, it is necessary for UTP to implement m-learning
in UTP. This paper presents a study on the students- perceptions on
mobile utilization in the learning practices in UTP. Besides, this
paper also presents a survey that was conducted among 82 students
from System Analysis and Design (SAD) course in UTP. The survey
includes basic information of mobile devices that have been used by
the students, opinions on current learning practices and also the
opinions regarding the m-learning implementation in the current
learning practices especially in SAD course. Based on the results of
the survey, majority of the students are using the mobile devices that
can support m-learning environment. Other than that, students also
agreed that current learning practices are ineffective and they believe
that m-learning utilization can improve the effectiveness of current
learning practices.
Abstract: Charging and discharging phenomenon on the surface
of materials can be found in plasma display panel, spacecraft
charging, high voltage insulator, etc. This report gives a simple
explanation on this phenomenon. A scanning electron microscope
was used not only as a tool to produce energetic electron beam to
charge an insulator without metallic coating and to produce a surface
discharging (surface breakdown/flashover) but also to observe the
visible charging and discharging on the sample surface. A model of
electric field distribution on the surface was developed in order to
explain charging and discharging phenomena. Since charging and
discharging process involves incubation time, therefore this process
can be used to evaluate the insulation property of materials under
electron bombardment.
Abstract: Music segmentation is a key issue in music information
retrieval (MIR) as it provides an insight into the
internal structure of a composition. Structural information about
a composition can improve several tasks related to MIR such
as searching and browsing large music collections, visualizing
musical structure, lyric alignment, and music summarization.
The authors of this paper present the MTSSM framework, a twolayer
framework for the multi-track segmentation of symbolic
music. The strength of this framework lies in the combination of
existing methods for local track segmentation and the application
of global structure information spanning via multiple tracks.
The first layer of the MTSSM uses various string matching
techniques to detect the best candidate segmentations for each
track of a multi-track composition independently. The second
layer combines all single track results and determines the best
segmentation for each track in respect to the global structure of
the composition.
Abstract: Thermal conductivity is an important characteristic of
a nanofluid in laminar flow heat transfer. This paper presents an
improved model for the prediction of the effective thermal
conductivity of nanofluids based on dimensionless groups. The
model expresses the thermal conductivity of a nanofluid as a function
of the thermal conductivity of the solid and liquid, their volume
fractions and particle size. The proposed model includes a parameter
which accounts for the interfacial shell, brownian motion, and
aggregation of particle. The validation of the model is verified by
applying the results obtained by the experiments of Tio2-water and
Al2o3-water nanofluids.
Abstract: In this paper, the potential security issues brought by the virtualization of a Software Defined Networks (SDN) would be analyzed. The virtualization of SDN is achieved by FlowVisor (FV). With FV, a physical network is divided into multiple isolated logical networks while the underlying resources are still shared by different slices (isolated logical networks). However, along with the benefits brought by network virtualization, it also presents some issues regarding security. By examining security issues existing in an OpenFlow network, which uses FlowVisor to slice it into multiple virtual networks, we hope we can get some significant results and also can get furtherdiscussions among the security of SDN virtualization.
Abstract: The springs located in urban areas are the outpouring
of surface water, which can serve as water supply, effluent receptors
and important local macro-drainage elements. With unplanned
occupation, non-compliance with environmental legislation and the
importance of these water bodies, it is vital to analyze the springs
within urban areas, considering the Brazilian forest code. This paper
submits an analysis and discussion methodology proposal of
environmental compliance functions of urban springs, by means of
G.I.S. - Geographic Information System analysis - and in situ
analysis. The case study included two springs which exhibit a history
of occupation along its length, with different degrees of impact. The
proposed method is effective and easy to apply, representing a
powerful tool for analyzing the environmental conditions of springs
in urban areas.
Abstract: In this paper, a simple microfluidic device for monitoring algal cell behavior is proposed. An array of algal microwells is fabricated by PDMS soft-lithography using X-ray LIGA mold, placed on a glass substrate. Two layers of replicated PDMS and substrate are attached by oxygen plasma bonding, creating a microchannel for the microfluidic system. Algal cell are loaded into the microfluidic device, which provides positive charge on the bottom surface of wells. Algal cells, which are negative charged, can be attracted to the bottom of the wells via electrostatic interaction. By varying the concentration of algal cells in the loading suspension, it is possible to obtain wells with a single cell. Liquid medium for cells monitoring are flown continuously over the wells, providing nutrient and waste exchange between the well and the main flow. This device could lead to the uncovering of the quantitative biology of the algae, which is a key to effective and extensive algal utilizations in the field of biotechnology, food industry and bioenergy research and developments.
Abstract: In this study, a vibration analysis was carried out of
symmetric angle-ply laminated composite plates with and without
square hole when subjected to compressive loads, numerically. A
buckling analysis is also performed to determine the buckling load of
laminated plates. For each fibre orientation, the compression load is
taken equal to 50% of the corresponding buckling load. In the
analysis, finite element method (FEM) was applied to perform
parametric studies, the effects of degree of orthotropy and stacking
sequence upon the fundamental frequencies and buckling loads are
discussed. The results show that the presence of a constant
compressive load tends to reduce uniformly the natural frequencies
for materials which have a low degree of orthotropy. However, this
reduction becomes non-uniform for materials with a higher degree of
orthotropy.
Abstract: Blind Signature were introduced by Chaum. In this
scheme, a signer can “sign” a document without knowing the
document contain. This is particularly important in electronic voting.
CryptO-0N2 is an electronic voting protocol which is development of
CryptO-0N. During its development this protocol has not been
furnished with the requirement of blind signature, so the choice of
voters can be determined by counting center. In this paper will be
presented of implementation of blind signature using RSA algorithm.
Abstract: The Reverse Monte Carlo (RMC) simulation is applied in the study of an aqueous electrolyte LiCl6H2O. On the basis of the available experimental neutron scattering data, RMC computes pair radial distribution functions in order to explore the structural features of the system. The obtained results include some unrealistic features. To overcome this problem, we use the Hybrid Reverse Monte Carlo (HRMC), incorporating an energy constraint in addition to the commonly used constraints derived from experimental data. Our results show a good agreement between experimental and computed partial distribution functions (PDFs) as well as a significant improvement in pair partial distribution curves. This kind of study can be considered as a useful test for a defined interaction model for conventional simulation techniques.
Abstract: We present a prototype interactive (hyper) map of strategic, tactical, and logistic options for Supply Chain Management. The map comprises an anthology of options, broadly classified within the strategic spectrum of efficiency versus responsiveness, and according to logistic and cross-functional drivers. They are exemplified by cases in diverse industries. We seek to get all these information and ideas organized to help supply chain managers identify effective choices for specific business environments. The key and innovative linkage we introduce is the configuration of competitive forces. Instead of going through seemingly endless and isolated cases and wondering how one can borrow from them, we aim to provide a guide by force comparisons. The premise is that best practices in a different industry facing similar forces may be a most productive resource in supply chain design and planning. A prototype template is demonstrated.
Abstract: The noteworthy point in the advancement of Brain Machine Interface (BMI) research is the ability to accurately extract features of the brain signals and to classify them into targeted control action with the easiest procedures since the expected beneficiaries are of disabled. In this paper, a new feature extraction method using the combination of adaptive band pass filters and adaptive autoregressive (AAR) modelling is proposed and applied to the classification of right and left motor imagery signals extracted from the brain. The introduction of the adaptive bandpass filter improves the characterization process of the autocorrelation functions of the AAR models, as it enhances and strengthens the EEG signal, which is noisy and stochastic in nature. The experimental results on the Graz BCI data set have shown that by implementing the proposed feature extraction method, a LDA and SVM classifier outperforms other AAR approaches of the BCI 2003 competition in terms of the mutual information, the competition criterion, or misclassification rate.
Abstract: Prickly pear (Opuntia spp) fruit has received renewed
interest since it contains a betalain pigment that has an attractive
purple colour for the production of juice. Prickly pear juice was
prepared by homogenizing the fruit and treating the pulp with 48 g of
pectinase from Aspergillus niger. Titratable acidity was determined
by diluting 10 ml prickly pear juice with 90 ml deionized water and
titrating to pH 8.2 with 0.1 N NaOH. Brix was measured using a
refractometer and ascorbic acid content assayed
spectrophotometrically. Colour variation was determined
colorimetrically (Hunter L.a.b.). Hunter L.a.b. analysis showed that
the red purple colour of prickly pear juice had been affected by juice
treatments. This was indicated by low light values of colour
difference meter (CDML*), hue, CDMa* and CDMb* values. It was
observed that non-treated prickly pear juice had a high (colour
difference meter of light) CDML* of 3.9 compared to juice
treatments (range 3.29 to 2.14). The CDML* significantly (p
Abstract: The new architecture for quantum cellular
automata is offered. A QCA cell includes two layers nc-Si,
divided by a dielectric. Among themselves cells are connected
by the bridge from a conductive material. The comparison is
made between this and QCA, offered earlier by C. Lent's
group.
Abstract: There is strong evidence that water channel proteins
'aquaporins (AQPs)' are central components in plant-water relations
as well as a number of other physiological parameters. We had
previously reported the isolation of 24 plasma membrane intrinsic
protein (PIP) type AQPs. However, the gene numbers in rice and the
polyploid nature of bread wheat indicated a high probability of
further genes in the latter. The present work focused on identification
of further AQP isoforms in bread wheat. With the use of altered
primer design, we identified five genes homologous, designated
PIP1;5b, PIP2;9b, TaPIP2;2, TaPIP2;2a, TaPIP2;2b. Sequence
alignments indicate PIP1;5b, PIP2;9b are likely to be homeologues of
two previously reported genes while the other three are new genes
and could be homeologs of each other. The results indicate further
AQP diversity in wheat and the sequence data will enable physical
mapping of these genes to identify their genomes as well as genetic to
determine their association with any quantitative trait loci (QTLs)
associated with plant-water relation such as salinity or drought
tolerance.
Abstract: In this study, the hydrogen transport phenomenon was
numerically evaluated by using hydrogen-enhanced localized
plasticity (HELP) mechanisms. Two dominant governing equations,
namely, the hydrogen transport model and the elasto-plastic model,
were introduced. In addition, the implicitly formulated equations of
the governing equations were implemented into ABAQUS UMAT
user-defined subroutines. The simulation results were compared to
published results to validate the proposed method.
Abstract: Checkpointing is one of the commonly used techniques to provide fault-tolerance in distributed systems so that the system can operate even if one or more components have failed. However, mobile computing systems are constrained by low bandwidth, mobility, lack of stable storage, frequent disconnections and limited battery life. Hence, checkpointing protocols having lesser number of synchronization messages and fewer checkpoints are preferred in mobile environment. There are two different approaches, although not orthogonal, to checkpoint mobile computing systems namely, time-based and index-based. Our protocol is a fusion of these two approaches, though not first of its kind. In the present exposition, an index-based checkpointing protocol has been developed, which uses time to indirectly coordinate the creation of consistent global checkpoints for mobile computing systems. The proposed algorithm is non-blocking, adaptive, and does not use any control message. Compared to other contemporary checkpointing algorithms, it is computationally more efficient because it takes lesser number of checkpoints and does not need to compute dependency relationships. A brief account of important and relevant works in both the fields, time-based and index-based, has also been included in the presentation.