Abstract: In the present work, the performance of the particle
swarm optimization and the genetic algorithm compared as a typical
geometry design problem. The design maximizes the heat transfer
rate from a given fin volume. The analysis presumes that a linear
temperature distribution along the fin. The fin profile generated using
the B-spline curves and controlled by the change of control point
coordinates. An inverse method applied to find the appropriate fin
geometry yield the linear temperature distribution along the fin
corresponds to optimum design. The numbers of the populations, the
count of iterations and time to convergence measure efficiency.
Results show that the particle swarm optimization is most efficient
for geometry optimization.
Abstract: This work addresses the problem of optimizing
completely batch water-using network with multiple contaminants
where the flow change caused by mass transfer is taken into
consideration for the first time. A mathematical technique for
optimizing water-using network is proposed based on
source-tank-sink superstructure. The task is to obtain the freshwater
usage, recycle assignments among water-using units, wastewater
discharge and a steady water-using network configuration by
following steps. Firstly, operating sequences of water-using units are
determined by time constraints. Next, superstructure is simplified by
eliminating the reuse and recycle from water-using units with
maximum concentration of key contaminants. Then, the non-linear
programming model is solved by GAMS (General Algebra Model
System) for minimum freshwater usage, maximum water recycle and
minimum wastewater discharge. Finally, numbers of operating periods
are calculated to acquire the steady network configuration. A case
study is solved to illustrate the applicability of the proposed approach.
Abstract: Packet switched data network like Internet, which has
traditionally supported throughput sensitive applications such as email
and file transfer, is increasingly supporting delay-sensitive
multimedia applications such as interactive video. These delaysensitive
applications would often rather sacrifice some throughput
for better delay. Unfortunately, the current packet switched network
does not offer choices, but instead provides monolithic best-effort
service to all applications. This paper evaluates Class Based Queuing
(CBQ), Coordinated Earliest Deadline First (CEDF), Weighted
Switch Deficit Round Robin (WSDRR) and RED-Boston scheduling
schemes that is sensitive to delay bound expectations for variety of
real time applications and an enhancement of WSDRR is proposed.
Abstract: To reduce accidents in the industry, WSNs(Wireless Sensor
networks)- sensor data is used. WSNs- sensor data has the persistence and
continuity. therefore, we design and exploit the buffer management system that
has the persistence and continuity to avoid and delivery data conflicts. To
develop modules, we use the multi buffers and design the buffer management
modules that transfer sensor data through the context-aware methods.
Abstract: Fossil fuels are the major source to meet the world
energy requirements but its rapidly diminishing rate and adverse
effects on our ecological system are of major concern. Renewable
energy utilization is the need of time to meet the future challenges.
Ocean energy is the one of these promising energy resources. Threefourths
of the earth-s surface is covered by the oceans. This enormous
energy resource is contained in the oceans- waters, the air above the
oceans, and the land beneath them. The renewable energy source of
ocean mainly is contained in waves, ocean current and offshore solar
energy. Very fewer efforts have been made to harness this reliable
and predictable resource. Harnessing of ocean energy needs detail
knowledge of underlying mathematical governing equation and their
analysis. With the advent of extra ordinary computational resources
it is now possible to predict the wave climatology in lab simulation.
Several techniques have been developed mostly stem from numerical
analysis of Navier Stokes equations. This paper presents a brief over
view of such mathematical model and tools to understand and
analyze the wave climatology. Models of 1st, 2nd and 3rd generations
have been developed to estimate the wave characteristics to assess the
power potential. A brief overview of available wave energy
technologies is also given. A novel concept of on-shore wave energy
extraction method is also presented at the end. The concept is based
upon total energy conservation, where energy of wave is transferred
to the flexible converter to increase its kinetic energy. Squeezing
action by the external pressure on the converter body results in
increase velocities at discharge section. High velocity head then can
be used for energy storage or for direct utility of power generation.
This converter utilizes the both potential and kinetic energy of the
waves and designed for on-shore or near-shore application. Increased
wave height at the shore due to shoaling effects increases the
potential energy of the waves which is converted to renewable
energy. This approach will result in economic wave energy
converter due to near shore installation and more dense waves due to
shoaling. Method will be more efficient because of tapping both
potential and kinetic energy of the waves.
Abstract: In order to meet environmental norms, Indian fuel
policy aims at producing ultra low sulphur diesel (ULSD) in near
future. A catalyst for meeting such requirements has been developed
and kinetics of this catalytic process is being looked into. In the
present investigations, effect of mass transfer on kinetics of ultra deep
hydrodesulphurization (UDHDS) to produce ULSD has been studied
to determine intrinsic kinetics over a pre-sulphided catalyst.
Experiments have been carried out in a continuous flow micro reactor
operated in the temperature range of 330 to 3600C, whsv of 1 hr-1 at a
pressure of 35 bar, and its parameters estimated. Based on the derived
rate expression and estimated parameters optimum operation range
has been determined for this UDHDS catalyst to obtain ULSD
product.
Abstract: Modularized design approach can facilitate the
modeling of complex systems and support behavior analysis and
simulation in an iterative and thus complex engineering process, by
using encapsulated submodels of components and of their interfaces.
Therefore it can improve the design efficiency and simplify the
solving complicated problem. Multi-drivers off-road vehicle is
comparatively complicated. Driving-line is an important core part to a
vehicle; it has a significant contribution to the performance of a
vehicle. Multi-driver off-road vehicles have complex driving-line, so
its performance is heavily dependent on the driving-line. A typical
off-road vehicle-s driving-line system consists of torque converter,
transmission, transfer case and driving-axles, which transfer the
power, generated by the engine and distribute it effectively to the
driving wheels according to the road condition. According to its main
function, this paper puts forward a modularized approach for
designing and evaluation of vehicle-s driving-line. It can be used to
effectively estimate the performance of driving-line during concept
design stage. Through appropriate analysis and assessment method, an
optimal design can be reached. This method has been applied to the
practical vehicle design, it can improve the design efficiency and is
convenient to assess and validate the performance of a vehicle,
especially of multi-drivers off-road vehicle.
Abstract: The argument that self-disclosure will change the
psychoanalytic process into a socio-cultural niche distorting the
therapeutic alliance and compromise therapeutic effectiveness is still
the widely held belief amongst many psychotherapists. This paper
considers the issues surrounding culture, disclosure and concealment
since they remain largely untheorized and clinically problematic. The
first part of the paper will critically examine the theory and practice
of psychoanalysis across cultures, and explore the reasons for
culturally diverse patients to conceal rather than disclose their
feelings and thoughts in the transference. This is followed by a
discussion on how immigrant analysts- anonymity is difficult to
maintain since diverse nationalities, language and accents provide
clues to the therapist-s and patient-s origins. Through personal
clinical examples of one the author-s (who is an immigrant) the paper
analyses the transference-countertransference paradigm and how it
reflects in the analyst-s self-revelation.
Abstract: Back-to-back static synchronous compensator (BtBSTATCOM) consists of two back-to-back voltage-source converters (VSC) with a common DC link in a substation. This configuration extends the capabilities of conventional STATCOM that bidirectional active power transfer from one bus to another is possible. In this paper, VSCs are designed in quasi multi-pulse form in which GTOs are triggered only once per cycle in PSCAD/EMTDC. The design details of VSCs as well as gate switching circuits and controllers are fully represented. Regulation modes of BtBSTATCOM are verified and tested on a multi-machine power system through different simulation cases. The results presented in the form of typical time responses show that practical PI controllers are almost robust and stable in case of start-up, set-point change, and line faults.
Abstract: This research focuses on the effect of weight
percentage variation and size variation of MgFeSi added,
gating system design and reaction chamber design on inmold
process. By using inmold process, well-known problem of
fading is avoided because the liquid iron reacts with
magnesium in the mold and not, as usual, in the ladle. During
the pouring operation, liquid metal passes through the
chamber containing the magnesium, where the reaction of the
metal with magnesium proceeds in the absence of atmospheric
oxygen [1].In this paper, the results of microstructural
characteristic of ductile iron on this parameters are mentioned.
The mechanisms of the inmold process are also described [2].
The data obtained from this research will assist in producing
the vehicle parts and other machinery parts for different
industrial zones and government industries and in transferring
the technology to all industrial zones in Myanmar. Therefore,
the inmold technology offers many advantages over traditional
treatment methods both from a technical and environmental,
as well as an economical point of view. The main objective of
this research is to produce ductile iron castings in all industrial
sectors in Myanmar more easily with lower costs. It will also
assist the sharing of knowledge and experience related to the
ductile iron production.
Abstract: In Algeria, now, the oil pumping plants are fed with electric power by independent local sources. This type of feeding has many advantages (little climatic influence, independent operation). However it requires a qualified maintenance staff, a rather high frequency of maintenance and repair and additional fuel costs. Taking into account the increasing development of the national electric supply network (Sonelgaz), a real possibility of transfer of the local sources towards centralized sources appears.These latter cannot only be more economic but more reliable than the independent local sources as well. In order to carry out this transfer, it is necessary to work out an optimal strategy to rebuilding these networks taking in account the economic parameters and the indices of reliability.
Abstract: The Lattice Boltzmann Method (LBM) with double populations is applied to solve the steady-state laminar natural convective heat transfer in a triangular cavity filled with water. The bottom wall is heated, the vertical wall is cooled, and the inclined wall is kept adiabatic. The buoyancy effect was modeled by applying the Boussinesq approximation to the momentum equation. The fluid velocity is determined by D2Q9 LBM and the energy equation is discritized by D2Q4 LBM to compute the temperature field. Comparisons with previously published work are performed and found to be in excellent agreement. Numerical results are obtained for a wide range of parameters: the Rayleigh number from to and the inclination angle from 0° to 360°. Flow and thermal fields were exhibited by means of streamlines and isotherms. It is observed that inclination angle can be used as a relevant parameter to control heat transfer in right-angled triangular enclosures.
Abstract: A theoretical study is conducted to design and explore
the effect of different parameters such as heat loads, the tube size of
piping system, wick thickness, porosity and hole size on the
performance and capability of a Loop Heat Pipe(LHP). This paper
presents a steady state model that describes the different phenomena
inside a LHP. Loop Heat Pipes(LHPs) are two-phase heat transfer
devices with capillary pumping of a working fluid. By their original
design comparing with heat pipes and special properties of the
capillary structure, they-re capable of transferring heat efficiency for
distances up to several meters at any orientation in the gravity field,
or to several meters in a horizontal position. This theoretical model is
described by different relations to satisfy important limits such as
capillary and nucleate boiling. An algorithm is developed to predict
the size of the LHP satisfying the limitations mentioned above for a
wide range of applied loads. Finally, to assess and evaluate the
algorithm and all the relations considered, we have used to design a
new kind of LHP to recover the heat from the exhaust of an actual
Gas Turbine. By finding the results, it showed that we can use the
LHP as a very high efficient device to recover the heat even in high
amount of loads(exhaust of a gas turbine). The sizes of all parts of the
LHP were obtained using the developed algorithm.
Abstract: The growth of open networks created the interest to commercialise it. The establishment of an electronic business mechanism must be accompanied by a digital-electronic payment system to transfer the value of transactions. Financial organizations are requested to offer a secure e-payment synthesis with equivalent levels of trust and security served in conventional paper-based payment transactions. The paper addresses the challenge of the first trade problem in e-commerce, provides a brief literature review on electronic payment and attempts to explain the underlying concept and method of trust in relevance to electronic payment.
Abstract: A numerical investigation has carried out to understand the melting characteristics of phase change material (PCM) in a fin type latent heat storage with the addition of embedded aluminum spiral fillers. It is known that melting performance of PCM can be significantly improved by increasing the number of embedded metallic fins in the latent heat storage system but to certain values where only lead to small improvement in heat transfer rate. Hence, adding aluminum spiral fillers within the fin gap can be an option to improve heat transfer internally. This paper presents extensive computational visualizations on the PCM melting patterns of the proposed fin-spiral fillers configuration. The aim of this investigation is to understand the PCM-s melting behaviors by observing the natural convection currents movement and melting fronts formation. Fluent 6.3 simulation software was utilized in producing twodimensional visualizations of melting fractions, temperature distributions and flow fields to illustrate the melting process internally. The results show that adding aluminum spiral fillers in Fin type latent heat storage can promoted small but more active natural convection currents and improve melting of PCM.
Abstract: This paper examines the use of mechanical aerator for
oxidation-ditch process. The rotor, which controls the aeration, is the
main component of the aeration process. Therefore, the objective of
this study is to find out the variations in overall oxygen transfer
coefficient (KLa) and aeration efficiency (AE) for different
configurations of aerator by varying the parameters viz. speed of
aerator, depth of immersion, blade tip angles so as to yield higher
values of KLa and AE. Six different configurations of aerator were
developed and fabricated in the laboratory and were tested for abovementioned
parameters. The curved blade rotor (CBR) emerged as a
potential aerator with blade tip angle of 47°.
The mathematical models are developed for predicting the
behaviour of CBR w.r.t kLa and power. In laboratory studies, the
optimum value of KLa and AE were observed to be 10.33 h-1 and
2.269 kg O2/ kWh.
Abstract: The equations governing the flow of an electrically conducting, incompressible viscous fluid over an infinite flat plate in the presence of a magnetic field are investigated using the homotopy perturbation method (HPM) with Padé approximants (PA) and 4th order Runge–Kutta method (4RKM). Approximate analytical and numerical solutions for the velocity field and heat transfer are obtained and compared with each other, showing excellent agreement. The effects of the magnetic parameter and Prandtl number on velocity field, shear stress, temperature and heat transfer are discussed as well.
Abstract: With the hardware technology advancing, the cost of
storing is decreasing. Thus there is an urgent need for new techniques
and tools that can intelligently and automatically assist us in
transferring this data into useful knowledge. Different techniques of
data mining are developed which are helpful for handling these large
size databases [7]. Data mining is also finding its role in the field of
biotechnology. Pedigree means the associated ancestry of a crop
variety. Genetic diversity is the variation in the genetic composition
of individuals within or among species. Genetic diversity depends
upon the pedigree information of the varieties. Parents at lower
hierarchic levels have more weightage for predicting genetic
diversity as compared to the upper hierarchic levels. The weightage
decreases as the level increases. For crossbreeding, the two varieties
should be more and more genetically diverse so as to incorporate the
useful characters of the two varieties in the newly developed variety.
This paper discusses the searching and analyzing of different possible
pairs of varieties selected on the basis of morphological characters,
Climatic conditions and Nutrients so as to obtain the most optimal
pair that can produce the required crossbreed variety. An algorithm
was developed to determine the genetic diversity between the
selected wheat varieties. Cluster analysis technique is used for
retrieving the results.
Abstract: In this paper, the ice melting in rectangular,
cylindrical and conical forms, which are erected vertically against air
flow, are experimentally studied in the free convection regime.The
results obtained are: Nusslet Number, heat transfer coefficient
andGrashof Number, and the variations of the said numbers in
relation to the time. The variations of ice slab area and volume are
measured, too.
Abstract: The study is based on the assumption that media products are appropriate subjects for the exploration of social and cultural identities as a keystone of value orientations of their authors, producers and target audiences. The research object of the study is the title page of the book cover of a professional publication that serves as a medium of marketing, scientific and intercultural communication, which is the result of semiotic and intercultural transfer. The study aims to answer the question whether the book cover is an expression of conceptualization and tool for social identity construction. It attempts to determine what value orientations and what concepts of social and cultural identities are hidden in the narrative structures of the book cover of the Czech translation of the book by G. Ritzer The McDonaldization of Society (1993), issued after the fall of the iron curtain in 1996 in the Czech Republic.