Abstract: The National Bridge Inventory (NBI) includes more
than 600,000 bridges within the United States of America.
Prestressed concrete girder bridges represent one of the most widely
used bridge systems. The majority of these girder bridges were
constructed using 0.5 and 0.6 inch diameter strands. The main
impediments to using larger strand diameters are: 1) lack of prestress
bed capacities, 2) lack of structural knowledge regarding the transfer
and development length of larger strands, and 3) the possibility of
developing wider end zone cracks upon strand release.
This paper presents a study about using 0.7 inch strands in girder
fabrication. Transfer and development length were evaluated, and
girders were fabricated using 0.7 inch strands at different spacings.
Results showed that 0.7 inch strands can be used at 2.0 inch spacing
without violating the AASHTO LRFD Specifications, while attaining
superior performance in shear and flexure.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: From ancient times Turkic languages have been in
contact with numerous representatives of different language families.
The article discusses the Turkic - Indian language contact and were
shown promise and necessity of this trend for the Turkic linguistics, were given Turkic - Indian lexical parallels in the framework of the nostratic language's macro family. The research work has done on the base of lexical parallels (LP) -of Turkic (which belong to the Altaic family of languages) and Indian (including Dravidian and Indo-Aryan languages).
Abstract: In this paper we propose the study of a centrifugal pump control system driven by a three-phase induction motor, which is supplied by a PhotoVoltaic PV generator. The system includes solar panel, a DC / DC converter equipped with its MPPT control, a voltage inverter to three-phase Pulse Width Modulation - PWM and a centrifugal pump driven by a three phase induction motor. In order to control the flow of the centrifugal pump, a Direct Torque Control - DTC of the induction machine is used. To illustrate the performances of the control, simulation results are carried out using Matlab/Simulink.
Abstract: Latvia is the fourth in the world by means of broadband internet speed. The total number of internet users in Latvia exceeds 70% of its population. The number of active mailboxes of the local internet e-mail service Inbox.lv accounts for 68% of the population and 97.6% of the total number of internet users. The Latvian portal Draugiem.lv is a phenomenon of social media, because 58.4 % of the population and 83.5% of internet users use it. A majority of Latvian company profiles are available on social networks, the most popular being Twitter.com. These and other parameters prove the fact consumers and companies are actively using the Internet.
However, after the authors in a number of studies analyzed how enterprises are employing the e-environment, namely, e-environment tools, they arrived to the conclusions that are not as flattering as the aforementioned statistics. There is an obvious contradiction between the statistical data and the actual studies. As a result, the authors have posed a question: Why are entrepreneurs resistant to e-tools? In order to answer this question, the authors have addressed the Technology Acceptance Model (TAM). The authors analyzed each phase and determined several factors affecting the use of e-environment, reaching the main conclusion that entrepreneurs do not have a sufficient level of e-literacy (digital literacy).
The authors employ well-established quantitative and qualitative methods of research: grouping, analysis, statistic method, factor analysis in SPSS 20 environment etc.
The theoretical and methodological background of the research is formed by, scientific researches and publications, that from the mass media and professional literature, statistical information from legal institutions as well as information collected by the author during the survey.
Abstract: Spherical shaped magnetite (Fe3O4) and Au@Fe3O4
nanoparticles were successfully synthesized from Fe electrodes
immersed in water with CTAB surfactant and HAuCl4 solution using
simple method-pulsed plasma in liquid, without the use of dopants or
special conditions for stabilization. Vibrating sample magnetometer
indicated ferromagnetic behavior of particles at room temperature with
coercivity and saturation magnetization of (Hc=105 Oe, Ms=6.83
emu/g) for Fe3O4 and (Hc=175, Ms=3.56emu/g) for Au@Fe3O4
nanoparticles. Structure and morphology of nanoparticles were
characterized by X-ray Diffraction analysis and HR-TEM
measurements. The cytotoxicity of nanoparticles was indicated using a
XTT assay to be very low (cell viability: 98-89% with Fe3O4 and
99-91% for Au@Fe3O4 NPs).
Abstract: In this paper, subtractive clustering based fuzzy inference system approach is used for early detection of faults in the function oriented software systems. This approach has been tested with real time defect datasets of NASA software projects named as PC1 and CM1. Both the code based model and joined model (combination of the requirement and code based metrics) of the datasets are used for training and testing of the proposed approach. The performance of the models is recorded in terms of Accuracy, MAE and RMSE values. The performance of the proposed approach is better in case of Joined Model. As evidenced from the results obtained it can be concluded that Clustering and fuzzy logic together provide a simple yet powerful means to model the earlier detection of faults in the function oriented software systems.
Abstract: ELS is an important ground based hardware in the
loop simulator used for aerodynamics torque loading experiments
of the actuators under test. This work focuses on improvement of the
transient response of torque controller with parameters uncertainty
of Electrical Load Simulator (ELS).The parameters of load simulator
are estimated online and the model is updated, eliminating the model
error and improving the steady state torque tracking response of
torque controller. To improve the Transient control performance the
gain of robust term of SMC is updated online using fuzzy logic
system based on the amount of uncertainty in parameters of load
simulator. The states of load simulator which cannot be measured
directly are estimated using luenberger observer with update of new
estimated parameters. The stability of the control scheme is verified
using Lyapunov theorem. The validity of proposed control scheme is
verified using simulations.
Abstract: The mitigation of crop loss due to damaging freezes requires accurate air temperature prediction models. An improved model for temperature prediction in Georgia was developed by including information on seasonality and modifying parameters of an existing artificial neural network model. Alternative models were compared by instantiating and training multiple networks for each model. The inclusion of up to 24 hours of prior weather information and inputs reflecting the day of year were among improvements that reduced average four-hour prediction error by 0.18°C compared to the prior model. Results strongly suggest model developers should instantiate and train multiple networks with different initial weights to establish appropriate model parameters.
Abstract: Levenberg-Marquardt method (LM) was proposed to
be applied as a non-linear least-square fitting in the analysis of a
natural gamma-ray spectrum that was taken by the Hp (Ge) detector.
The Gaussian function that composed of three components, main
Gaussian, a step background function and tailing function in the lowenergy
side, has been suggested to describe each of the y-ray lines
mathematically in the spectrum. The whole spectrum has been
analyzed by determining the energy and relative intensity for the
strong y-ray lines.
Abstract: In this paper, the notion of Hyperbolic Klingenberg
plane is introduced via a set of axioms like as Affine Klingenberg
planes and Projective Klingenberg planes. Models of such planes are
constructed by deleting a certain number m of equivalence classes
of lines from a Projective Klingenberg plane. In the finite case, an
upper bound for m is established and some combinatoric properties
are investigated.
Abstract: The use of a Bayesian Hierarchical Model (BHM) to interpret breath measurements obtained during a 13C Octanoic Breath Test (13COBT) is demonstrated. The statistical analysis was implemented using WinBUGS, a commercially available computer package for Bayesian inference. A hierarchical setting was adopted where poorly defined parameters associated with a delayed Gastric Emptying (GE) were able to "borrow" strength from global distributions. This is proved to be a sufficient tool to correct model's failures and data inconsistencies apparent in conventional analyses employing a Non-linear least squares technique (NLS). Direct comparison of two parameters describing gastric emptying ng ( tlag -lag phase, t1/ 2 -half emptying time) revealed a strong correlation between the two methods. Despite our large dataset ( n = 164 ), Bayesian modeling was fast and provided a successful fitting for all subjects. On the contrary, NLS failed to return acceptable estimates in cases where GE was delayed.
Abstract: Forty-five dairy cows were used to compare the
enzyme activity of alkaline phosphatase (ALP), lactate
dehydrogenase (LDH), α -amylase in the cervical mucus of cows
during spontaneous and induced estrus using progestagen or PGF2 α
and to determine whether these enzymes affect the fertility in cows
with induced estrus, at the time of Al. The animals were assigned to 3
groups (no treatment, a Crestar® for 12 days, a double im injection of
PGF2 α). The cows were artificially inseminated (AI). Cervical
mucus samples were collected from all cows 3 to 5 min before the
AI. The results are summarized as follows: ALP and α -amylase
activity for spontaneous estrus were similar to those for induced
estrus (P>0.05) . LDH activity levels during spontaneous and PGF2 α
induced estrus was significantly lower (P < 0.001) than that in
progestagene induced estrus groups. While no difference was found
between the first and the third groups. Our result showed a significant
difference in LDH activity levels between cows conceived with 2 or
more AI and those conceived with 1 AI. The result of this study
showed that the enzyme activity in cervical mucus is helpful for
detection of ovulation and time of AI.
Abstract: The aim of this paper is to present a comparative
study on two different methods for the evaluation of the equilibrium
point of a ship, core issue for designing an On Board Stability System
(OBSS) module that, starting from geometry information of a ship
hull, described by a discrete model in a standard format, and the
distribution of all weights onboard calculates the ship floating
conditions (in draught, heel and trim).
Abstract: This paper describes an efficient hardware implementation of a new technique for interfacing the data exchange between the microprocessor-based systems and the external devices. This technique, based on the use of software/hardware system and a reduced physical address, enlarges the interfacing capacity of the microprocessor-based systems, uses the Direct Memory Access (DMA) to increases the frequency of the new bus, and improves the speed of data exchange. While using this architecture in microprocessor-based system or in computer, the input of the hardware part of our system will be connected to the bus system, and the output, which is a new bus, will be connected to an external device. The new bus is composed of a data bus, a control bus and an address bus. A Xilinx Integrated Software Environment (ISE) 7.1i has been used for the programmable logic implementation.
Abstract: In this study a neural network (NN) was proposed to
predict the sorption of binary mixture of copper-cobalt ions into
clinoptilolite as ion-exchanger. The configuration of the
backpropagation neural network giving the smallest mean square
error was three-layer NN with tangent sigmoid transfer function at
hidden layer with 10 neurons, linear transfer function at output layer
and Levenberg-Marquardt backpropagation training algorithm.
Experiments have been carried out in the batch reactor to obtain
equilibrium data of the individual sorption and the mixture of coppercobalt
ions. The obtained modeling results have shown that the used
of neural network has better adjusted the equilibrium data of the
binary system when compared with the conventional sorption
isotherm models.
Abstract: The main purpose of this research was to analyze Socio-Cultural obstacles of disseminating of nanotechnology in Iran's agricultural section. One hundred twenty eight out of a total of 190 researchers with different levels of expertise in and familiarity with nanotechnology were randomly selected and questionnaires completed by them. Face validity have been done by expert's suggestion and correction, reliability by using Cronbakh-Alpha formula. The results of a factor analysis showed variation for different factors. For cultural factors 19/475 percent, for management 13/139 percent, information factor 11/277 percent, production factor 9/703 percent, social factor 9/267 percent, and for attitude factor it became 8/947 percent. Also results indicated that socio-cultural factors were the most important obstacle for nanotechnology dissemination in agricultural section in Iran.
Abstract: D-erythro-cyclohexylserine (D
chiral unnatural β-hydroxy amino acid expected for the synthesis of drug for AIDS treatment. To develop a continuous bioconversion
system with whole cell biocatalyst of D-threonine aldolase (D genes for the D-erythro-CHS production, D-threonine aldolase gene
was amplified from Ensifer arboris 100383 by direct PCR amplication using two degenerated oligonucleotide primers designed based on
genomic sequence of Shinorhizobium meliloti
Sequence analysis of the cloned DNA fragment revealed one
open-reading frame of 1059 bp and 386 amino acids. This putative
D-TA gene was cloned into NdeI and EcoRI (pEnsi
His-tag sequence or BamHI (pEnsi-DTA[2])
sequence of the pET21(a) vector. The expression level of the cloned gene was extremely overexpressed by E. coli BL21(DE3) transformed with pEnsi-DTA[1] compared to E. coli BL21(DE3) transformed with
pEnsi-DTA[2]. When the cells expressing the wild
used for D-TA enzyme activity, 12 mM glycine was successfully
detected in HPLC analysis. Moreover, the whole cells harbouring the
recombinant D-TA was able to synthesize D-erythro
of 0.6 mg/ml in a batch reaction.
Abstract: In this paper bi-annual time series data on unemployment rates (from the Labour Force Survey) are expanded to quarterly rates and linked to quarterly unemployment rates (from the Quarterly Labour Force Survey). The resultant linked series and the consumer price index (CPI) series are examined using Johansen’s cointegration approach and vector error correction modeling. The study finds that both the series are integrated of order one and are cointegrated. A statistically significant co-integrating relationship is found to exist between the time series of unemployment rates and the CPI. Given this significant relationship, the study models this relationship using Vector Error Correction Models (VECM), one with a restriction on the deterministic term and the other with no restriction.
A formal statistical confirmation of the existence of a unique linear and lagged relationship between inflation and unemployment for the period between September 2000 and June 2011 is presented. For the given period, the CPI was found to be an unbiased predictor of the unemployment rate. This relationship can be explored further for the development of appropriate forecasting models incorporating other study variables.
Abstract: Proper management of residues originated from
industrial activities is considered as one of the serious challenges
faced by industrial societies due to their potential hazards to the
environment. Common disposal methods for industrial solid wastes
(ISWs) encompass various combinations of solely management
options, i.e. recycling, incineration, composting, and sanitary
landfilling. Indeed, the procedure used to evaluate and nominate the
best practical methods should be based on environmental, technical,
economical, and social assessments. In this paper an environmentaltechnical
assessment model is developed using analytical network
process (ANP) to facilitate the decision making practice for ISWs
generated at Gilan province, Iran. Using the results of performed
surveys on industrial units located at Gilan, the various groups of
solid wastes in the research area were characterized, and four
different ISW management scenarios were studied. The evaluation
process was conducted using the above-mentioned model in the
Super Decisions software (version 2.0.8) environment. The results
indicates that the best ISW management scenario for Gilan province
is consist of recycling the metal industries residues, composting the
putrescible portion of ISWs, combustion of paper, wood, fabric and
polymeric wastes as well as energy extraction in the incineration
plant, and finally landfilling the rest of the waste stream in addition
with rejected materials from recycling and compost production plants
and ashes from the incineration unit.