Abstract: Time interleaved sigma-delta (TIΣΔ) architecture is a
potential candidate for high bandwidth analog to digital converters
(ADC) which remains a bottleneck for software and cognitive radio
receivers. However, the performance of the TIΣΔ architecture is
limited by the unavoidable gain and offset mismatches resulting
from the manufacturing process. This paper presents a novel digital
calibration method to compensate the gain and offset mismatch
effect. The proposed method takes advantage of the reconstruction
digital signal processing on each channel and requires only few logic
components for implementation. The run time calibration is estimated
to 10 and 15 clock cycles for offset cancellation and gain mismatch
calibration respectively.
Abstract: Regenerative gas turbine engine cycle is presented that yields higher cycle efficiencies than simple cycle operating under the same conditions. The power output, efficiency and specific fuel consumption are simulated with respect to operating conditions. The analytical formulae about the relation to determine the thermal efficiency are derived taking into account the effected operation conditions (ambient temperature, compression ratio, regenerator effectiveness, compressor efficiency, turbine efficiency and turbine inlet temperature). Model calculations for a wide range of parameters are presented, as are comparisons with simple gas turbine cycle. The power output and thermal efficiency are found to be increasing with the regenerative effectiveness, and the compressor and turbine efficiencies. The efficiency increased with increase the compression ratio to 5, then efficiency decreased with increased compression ratio, but in simple cycle the thermal efficiency always increase with increased in compression ratio. The increased in ambient temperature caused decreased thermal efficiency, but the increased in turbine inlet temperature increase thermal efficiency.
Abstract: Increasing number of vehicles and lack of awareness among road users may lead to road accidents. However no specific literature was found to rank vehicles involved in accidents based on fuzzy variables of road users. This paper proposes a ranking of four selected motor vehicles involved in road accidents. Human and non-human factors that normally linked with road accidents are considered for ranking. The imprecision or vagueness inherent in the subjective assessment of the experts has led the application of fuzzy sets theory to deal with ranking problems. Data in form of linguistic variables were collected from three authorised personnel of three Malaysian Government agencies. The Multi Criteria Decision Making, fuzzy TOPSIS was applied in computational procedures. From the analysis, it shows that motorcycles vehicles yielded the highest closeness coefficient at 0.6225. A ranking can be drawn using the magnitude of closeness coefficient. It was indicated that the motorcycles recorded the first rank.
Abstract: Quantitative researching on the degree of incidence between the logistics industry and relevant macroscopic system elements is the basis of reasonable and scientific policy on industrial development. In the light of the macro-level, the logistics industry system is consisted of multiple macroscopic agents such as macro-economic, infrastructure, social environment, market demanding, the traditional industry, industry life cycle, policy , system and so on. This paper studies the grey incidence among the macroscopic agents in the logistics industry system. It is demonstrated that the releasing of the logistics services from the logistics outsourcing enterprises determines the growth of the logistics size. Although the information and communication technology is able to promote the formation of the modern logistics industry to some extent, the development of the modern logistics industry depends more on the development of national economy and the investment in the capital assets of the logistics industry.
Abstract: Complex assemblies of interacting proteins carry out
most of the interesting jobs in a cell, such as metabolism, DNA
synthesis, mitosis and cell division. These physiological properties
play out as a subtle molecular dance, choreographed by underlying
regulatory networks that control the activities of cyclin-dependent
kinases (CDK). The network can be modeled by a set of nonlinear
differential equations and its behavior predicted by numerical
simulation. In this paper, an innovative approach has been proposed
that uses genetic algorithms to mine a set of behavior data output by
a biological system in order to determine the kinetic parameters of
the system. In our approach, the machine learning method is
integrated with the framework of existent biological information in a
wiring diagram so that its findings are expressed in a form of system
dynamic behavior. By numerical simulations it has been illustrated
that the model is consistent with experiments and successfully shown
that such application of genetic algorithms will highly improve the
performance of mathematical model of the cell division cycle to
simulate such a complicated bio-system.
Abstract: The mechanical deformation and the electrical conductivity of lanthanum strontium cobalt ferrite oxide under uniaxial compression were investigated at various temperatures up to 1073 K. The material reveals a rather complex mechanical behaviour related to its ferroelasticity and completely different stress-strain curves are obtained during the 1st and 2nd loading cycles. A distinctive ferroelastic creep was observed at 293 K whilst typical ferroelastic stress-strain curve were obtained in the temperature range from 473 K to 873 K. At 1073 K, on the other hand, high-temperature creep deformation was observed instead of ferroelastic deformation. The conductivity increases with increasing compressive stress at all the temperatures. The increase in conductivity is related to both geometrical and piezoelectric effects. From 293 K to 873 K, where the material exhibits ferroelastic behaviour, the variation in the total conductivity decreases with increasing temperature. The contribution of the piezoelectric effect to the total conductivity variation also decreases with increasing temperature and the maximum in piezoconductivity has a value of about 0.75 % at 293 K for a compressive stress of 100 MPa. There is no effect of domain switching on conductivity except for the geometric effect. At 1073 K, the conductivity is simply proportional to the compressive strain.
Abstract: Mixed-traffic (e.g., pedestrians, bicycles, and vehicles)
data at an intersection is one of the essential factors for intersection
design and traffic control. However, some data such as pedestrian
volume cannot be directly collected by common detectors (e.g.
inductive loop, sonar and microwave sensors). In this paper, a video
based detection algorithm is proposed for mixed-traffic data collection
at intersections using surveillance cameras. The algorithm is derived
from Gaussian Mixture Model (GMM), and uses a mergence time
adjustment scheme to improve the traditional algorithm. Real-world
video data were selected to test the algorithm. The results show that
the proposed algorithm has the faster processing speed and more
accuracy than the traditional algorithm. This indicates that the
improved algorithm can be applied to detect mixed-traffic at
signalized intersection, even when conflicts occur.
Abstract: The aim of this study was to compare the
sensitometric properties of commonly used radiographic films
processed with chemical solutions in different workload hospitals.
The effect of different processing conditions on induced densities on
radiologic films was investigated. Two accessible double emulsions
Fuji and Kodak films were exposed with 11-step wedge and
processed with Champion and CPAC processing solutions. The
mentioned films provided in both workloads centers, high and low.
Our findings displays that the speed and contrast of Kodak filmscreen
in both work load (high and low) is higher than Fuji filmscreen
for both processing solutions. However there was significant
differences in films contrast for both workloads when CPAC solution
had been used (p=0.000 and 0.028). The results showed base plus
fog density for Kodak film was lower than Fuji. Generally Champion
processing solution caused more speed and contrast for investigated
films in different conditions and there was significant differences in
95% confidence level between two used processing solutions
(p=0.01). Low base plus fog density for Kodak films provide more
visibility and accuracy and higher contrast results in using lower
exposure factors to obtain better quality in resulting radiographs. In
this study we found an economic advantages since Champion
solution and Kodak film are used while it makes lower patient dose.
Thus, in a radiologic facility any change in film processor/processing
cycle or chemistry should be carefully investigated before
radiological procedures of patients are acquired.
Abstract: Two commercial proteases from Bacillus
licheniformis (Alcalase 2.4 L FG and Alcalase 2.5 L, Type DX) were
screened for the production of Z-Ala-Phe-NH2 in batch reaction.
Alcalase 2.4 L FG was the most efficient enzyme for the C-terminal
amidation of Z-Ala-Phe-OMe using ammonium carbamate as
ammonium source. Immobilization of protease has been achieved by
the sol-gel method, using dimethyldimethoxysilane (DMDMOS) and
tetramethoxysilane (TMOS) as precursors (unpublished results). In
batch production, about 95% of Z-Ala-Phe-NH2 was obtained at
30°C after 24 hours of incubation. Reproducibility of different
batches of commercial Alcalase 2.4 L FG preparations was also
investigated by evaluating the amidation activity and the entrapment
yields in the case of immobilization. A packed-bed reactor (0.68 cm
ID, 15.0 cm long) was operated successfully for the continuous
synthesis of peptide amides. The immobilized enzyme retained the
initial activity over 10 cycles of repeated use in continuous reactor at
ambient temperature. At 0.75 mL/min flow rate of the substrate
mixture, the total conversion of Z-Ala-Phe-OMe was achieved after 5
hours of substrate recycling. The product contained about 90%
peptide amide and 10% hydrolysis byproduct.
Abstract: This study describes a micro device integrated with
multi-chamber for polymerase chain reaction (PCR) with different
annealing temperatures. The device consists of the reaction
polydimethylsiloxane (PDMS) chip, a cover glass chip, and is
equipped with cartridge heaters, fans, and thermocouples for
temperature control. In this prototype, commercial software is utilized
to determine the geometric and operational parameters those are
responsible for creating the denaturation, annealing, and extension
temperatures within the chip. Two cartridge heaters are placed at two
sides of the chip and maintained at two different temperatures to
achieve a thermal gradient on the chip during the annealing step. The
temperatures on the chip surface are measured via an infrared imager.
Some thermocouples inserted into the reaction chambers are used to
obtain the transient temperature profiles of the reaction chambers
during several thermal cycles. The experimental temperatures
compared to the simulated results show a similar trend. This work
should be interesting to persons involved in the high-temperature
based reactions and genomics or cell analysis.
Abstract: Consumer behaviour analysis represents an important
field of study in marketing. Particularly strategy development for
marketing and communications will be more focused and effective
when marketers have an understanding of the motivations, behaviour
and psychology of consumers. While materialism has been found to
be one of the important elements in consumer behaviour, compulsive
consumption represents another aspect that has recently attracted
more attention. This is because of the growing prevalence of
dysfunctional buying that has raised concern in consumer societies.
Present studies and analyses on origins and motivations of
compulsive buying have mainly focused on either individual factors
or groups of related factors and hence a need for a holistic view
exists. This paper provides a comprehensive perspective on
compulsive consumption and establishes relevant propositions
keeping the family life cycle stages as a reference for the incidence of
chronic consumer states and their influence on compulsive
consumption.
Abstract: Porcelain specimens were fired at 6C/min to 1250C (dwell time 0.5-3h) and cooled at 6C/min to room temperature. Additionally, three different slower firing/cooling cycles were tried. Sintering profile and effects on MOR, crystalline phase content and morphology were investigated using dilatometry, 4-point bending strength, XRD and FEG-SEM respectively. Industrial-sized specimens prepared using the promising cycle were tested basing on the ANSI standards. Increasing dwell time from 1h to 3h at peak temperature of 1250C resulted in neither a significant effect on the quartz and mullite content nor MOR. Reducing the firing/cooling rate to below 6C/min, for peak temperature of 1250C (dwell time of 1h) does not result in improvement of strength of porcelain. The industrial sized specimen exhibited flashover voltages of 20.3kV (dry) and 9.3kV (wet) respectively, transverse strength of 12.5kN and bulk density of 2.27g/cm3, which are satisfactory. There was however dye penetration during porosity test. KeywordsDwell time, Microstructure, Porcelain, Strength.
Abstract: The classification of the protein structure is commonly
not performed for the whole protein but for structural domains, i.e.,
compact functional units preserved during evolution. Hence, a first
step to a protein structure classification is the separation of the
protein into its domains. We approach the problem of protein domain
identification by proposing a novel graph theoretical algorithm. We
represent the protein structure as an undirected, unweighted and
unlabeled graph which nodes correspond the secondary structure
elements of the protein. This graph is call the protein graph. The
domains are then identified as partitions of the graph corresponding
to vertices sets obtained by the maximization of an objective function,
which mutually maximizes the cycle distributions found in the
partitions of the graph. Our algorithm does not utilize any other kind
of information besides the cycle-distribution to find the partitions. If
a partition is found, the algorithm is iteratively applied to each of
the resulting subgraphs. As stop criterion, we calculate numerically
a significance level which indicates the stability of the predicted
partition against a random rewiring of the protein graph. Hence,
our algorithm terminates automatically its iterative application. We
present results for one and two domain proteins and compare our
results with the manually assigned domains by the SCOP database
and differences are discussed.
Abstract: An n×n matrix is called an N1 0 -matrix if all principal minors are non-positive and each entry is non-positive. In this paper, we study the partial non-combinatorially symmetric N1 0 -matrix completion problems if the graph of its specified entries is a transitive tournament or a double cycle. In general, these digraphs do not have N1 0 -completion. Therefore, we have given sufficient conditions that guarantee the existence of the N1 0 -completion for these digraphs.
Abstract: An inflation–extension test with human vena cava
inferior was performed with the aim to fit a material model. The vein
was modeled as a thick–walled tube loaded by internal pressure and
axial force. The material was assumed to be an incompressible
hyperelastic fiber reinforced continuum. Fibers are supposed to be
arranged in two families of anti–symmetric helices. Considered
anisotropy corresponds to local orthotropy. Used strain energy
density function was based on a concept of limiting strain
extensibility. The pressurization was comprised by four pre–cycles
under physiological venous loading (0 – 4kPa) and four cycles under
nonphysiological loading (0 – 21kPa). Each overloading cycle was
performed with different value of axial weight. Overloading data
were used in regression analysis to fit material model. Considered
model did not fit experimental data so good. Especially predictions
of axial force failed. It was hypothesized that due to
nonphysiological values of loading pressure and different values of
axial weight the material was not preconditioned enough and some
damage occurred inside the wall. A limiting fiber extensibility
parameter Jm was assumed to be in relation to supposed damage.
Each of overloading cycles was fitted separately with different values
of Jm. Other parameters were held the same. This approach turned out
to be successful. Variable value of Jm can describe changes in the
axial force – axial stretch response and satisfy pressure – radius
dependence simultaneously.
Abstract: This research studied about green logistics and the
expected benefit that organization gotten when adapted to green
logistics also the organization concerned about the important activity
in green logistics to apply in implementation from study was found
that the benefit of green logistics that organization was gotten by
logistics management which was the increased efficiency process of
management the product from producer to customer all of reduce
production cost, increased value added save energy and prevented
environment together
From study was found that the organization had green logistics to
apply in logistics activities in supply chain since downstream till
upstream to prevent environment as follow 1). Purchasing process,
trade facilitation enhance such as linking of information technology
during business to business (B2B business). 2). Productions process
improved by business logistics improvement 3). Warehouse
management process such as recycled packaging, moving goods in to
warehouse, transportation goods and inside receiving and delivery
products plan.
Abstract: The current of professional bicycle pedal-s
manufacturing model mostly used casting, forging, die-casting
processing methods, so the paper used 7075 aluminum alloy which is
to produce the bicycle parts most commonly, and employs the
rigid-plastic finite element (FE) DEFORMTM 3D software to simulate
and to analyze the professional bicycle pedal design. First we use Solid
works 2010 3D graphics software to design the professional bicycle
pedal of the mold and appearance, then import finite element (FE)
DEFORMTM 3D software for analysis. The paper used rigid-plastic
model analytical methods, and assuming mode to be rigid body. A
series of simulation analyses in which the variables depend on
different temperature of forging billet, friction factors, forging speed,
mold temperature are reveal to effective stress, effective strain, damage
and die radial load distribution for forging bicycle pedal. The analysis
results hope to provide professional bicycle pedal forming mold
references to identified whether suit with the finite element results for
high-strength design suitability of aluminum alloy.
Abstract: Reliability Centered Maintenance(RCM) is one of
most widely used methods in the modern power system to schedule a
maintenance cycle and determine the priority of inspection. In order
to apply the RCM method to the Smart Grid, a precedence study for
the new structure of rearranged system should be performed due to
introduction of additional installation such as renewable and
sustainable energy resources, energy storage devices and advanced
metering infrastructure. This paper proposes a new method to
evaluate the priority of maintenance and inspection of the power
system facilities in the Smart Grid using the Risk Priority Number. In
order to calculate that risk index, it is required that the reliability
block diagram should be analyzed for the Smart Grid system. Finally,
the feasible technical method is discussed to estimate the risk
potential as part of the RCM procedure.
Abstract: Organ motion, especially respiratory motion, is a technical challenge to radiation therapy planning and dosimetry. This motion induces displacements and deformation of the organ tissues within the irradiated region which need to be taken into account when simulating dose distribution during treatment. Finite element modeling (FEM) can provide a great insight into the mechanical behavior of the organs, since they are based on the biomechanical material properties, complex geometry of organs, and anatomical boundary conditions. In this paper we present an original approach that offers the possibility to combine image-based biomechanical models with particle transport simulations. We propose a new method to map material density information issued from CT images to deformable tetrahedral meshes. Based on the principle of mass conservation our method can correlate density variation of organ tissues with geometrical deformations during the different phases of the respiratory cycle. The first results are particularly encouraging, as local error quantification of density mapping on organ geometry and density variation with organ motion are performed to evaluate and validate our approach.
Abstract: This research studied recycled waste by the Recyclable Material Bank Project of 4 universities in the central region of Thailand for the evaluation of reducing greenhouse gas emissions compared with landfilling activity during July 2012 to June 2013. The results showed that the projects collected total amount of recyclable wastes of about 911,984.80 kilograms. Office paper had the largest amount among these recycled wastes (50.68% of total recycled waste). Groups of recycled waste can be prioritized from high to low according to their amount as paper, plastic, glass, mixed recyclables, and metal, respectively. The project reduced greenhouse gas emissions equivalent to about 2814.969 metric tons of carbon dioxide. The most significant recycled waste that affects the reduction of greenhouse gas emissions is office paper which is 70.16% of total reduced greenhouse gasses emission. According to amount of reduced greenhouse gasses emission, groups of recycled waste can be prioritized from high to low significances as paper, plastic, metals, mixed recyclables, and glass, respectively.