Abstract: For relatively small particles of aluminum (5%) is observed to
corrode before passivation occurs at moderate temperatures (>50oC)
in de-ionized water within one hour. Physical contact with alumina
powder results in a significant increase in both the rate of corrosion
and the extent of corrosion before passivation. Whereas the resulting
release of hydrogen gas could be of commercial interest for portable
hydrogen supply systems, the fundamental aspects of Al corrosion
acceleration in presence of dispersed alumina particles are equally
important. This paper investigates the effects of various amounts of
alumina on the corrosion rate of aluminum powders in water and the
effect of multiple additions of aluminum into a single reactor.
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a small
straight-bladed Darrieus-type vertical axis wind turbine depending on
blade geometrical section. It consists of an analytical code coupled to
a solid modeling software, capable of generating the desired blade
geometry based on the desired blade design geometric parameters.
Such module is then linked to a finite volume commercial CFD code
for the calculation of rotor performance by integration of the
aerodynamic forces along the perimeter of each blade for a full period
of revolution.After describing and validating the computational
model with experimental data, the results of numerical simulations
are proposed on the bases of two candidate airfoil sections, that is a
classical symmetrical NACA 0021 blade profile and the recently
developed DU 06-W-200 non-symmetric and laminar blade
profile.Through a full CFD campaign of analysis, the effects of blade
geometrical section on angle of attack are first investigated and then
the overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of airfoil geometry on overall rotor performance.
Abstract: Design and evaluation of reciprocating compressors
should include a pulsation study. The object is to ensure that
predicted pulsation levels meet guidelines to limit vibration, shaking
forces, noise, associated pressure drops, horsepower losses and
fabrication cost and time to acceptable levels. This paper explains
procedures and recommendations to select and size pulsation
suppression devices to obtain optimum arrangement in terms of
pulsation, vibration, shaking forces, performance, reliability, safety,
operation, maintenance and commercial conditions. Model and
advanced formulations for pulsation study are presented. The effect
of the full fluid dynamic model on the prediction of pulsation waves
and resulting frequency spectrum distributions are discussed.
Advanced and optimum methods of controlling pulsations are
highlighted. Useful recommendations and guidelines for pulsation
control, piping pulsation analysis, pulsation vessel design, shaking
forces, low pressure drop orifices, pulsation study report and devices
to mitigate pulsation and shaking problems are discussed.
Abstract: This paper examines the relationship between financial
risks and profitability of the conventional and Islamic banks in
Malaysia for the period between 1996 and 2005. The measures of
profitability that have been used in the study are the return on equity
(ROE) and return on assets (ROA) while the financial risks are credit
risk, interest rate risk and liquidity risks. This study employs panel
data regression analysis of Generalised Least Squares of fixed effects
and random effects models. It was found that credit risk has a
significant impact on ROA and ROE for the conventional as well as
the Islamic banks. The relationship between interest rate risk and ROE
were found to be weakly significant for the conventional banks and
insignificant for the Islamic banks. The effect of interest rate risk on
ROA is significant for the conventional banks. Liquidity risk was
found to have an insignificant impact on both profitability measures.
Abstract: The commercial finite element program LS-DYNA was employed to evaluate the response and energy absorbing capacity of cylindrical metal tubes that are externally wrapped with composite. The effects of composite wall thickness, loading conditions and fiber ply orientation were examined. The results demonstrate that a wrapped composite can be utilized effectively to enhance the crushing characteristics and energy absorbing capacity of the tubes. Increasing the thickness of the composite increases the mean force and the specific energy absorption under both static and dynamic crushing. The ply pattern affects the energy absorption capacity and the failure mode of the metal tube and the composite material property is also significant in determining energy absorption efficiency.
Abstract: Two-dimensional (2D) bar codes were designed to
carry significantly more data with higher information density and
robustness than its 1D counterpart. Thanks to the popular
combination of cameras and mobile phones, it will naturally bring
great commercial value to use the camera phone for 2D bar code
reading. This paper addresses the problem of specific 2D bar code
design for mobile phones and introduces a low-level encoding
method of matrix codes. At the same time, we propose an efficient
scheme for 2D bar codes decoding, of which the effort is put on
solutions of the difficulties introduced by low image quality that is
very common in bar code images taken by a phone camera.
Abstract: In the competitive environment of aircraft industries it becomes absolutely necessary to improve the efficiency, performance of the aircrafts to reduce the development and operating costs considerably, in order to capitalize the market. An important contribution to improve the efficiency and performance can be
achieved by decreasing the aircraft weight through considerable
usage of composite materials in primary aircraft structures. In this study, a type of composite material called Carbon Fiber Reinforced
Plastic (CFRP) is explored for the usage is aircraft skin panels. Even
though there were plenty of studies and research has been already
carried out, here a practical example of an aircraft skin panel is taken
and substantiated the benefits of composites material usage over the
metallic skin panel. A crown skin panel of a commercial aircraft is
designed using both metal and composite materials. Stress analysis
has been carried out for both and margin of safety is estimated for the
critical load cases. The skin panels are compared for manufacturing,
tooling, assembly and cost parameters. Detail step by step comparison between metal and composite constructions are studied
and results are tabulated for better understanding.
Abstract: This research aims at modeling and simulating the effects of nanofluids on cylindrical heat pipes thermal performance using the ANSYS-FLUENT CFD commercial software. The heat pipe outer wall temperature distribution, thermal resistance, liquid pressure and axial velocity in presence of suspended nano-scaled solid particle (i.e. Cu, Al2O3 and TiO2) within the fluid (water) were investigated. The effect of particle concentration and size were explored and it is concluded that the thermal performance of the heat pipe is improved when using nanofluid as the system working fluid. Additionally, it was observed that the thermal resistance of the heat pipe drops as the particle concentration level increases and particle radius decreases.
Abstract: Semantic Web services will enable the semiautomatic
and automatic annotation, advertisement, discovery,
selection, composition, and execution of inter-organization business
logic, making the Internet become a common global platform where
organizations and individuals communicate with each other to carry
out various commercial activities and to provide value-added
services. There is a growing consensus that Web services alone will
not be sufficient to develop valuable solutions due the degree of
heterogeneity, autonomy, and distribution of the Web. This paper
deals with two of the hottest R&D and technology areas currently
associated with the Web – Web services and the Semantic Web. It
presents the synergies that can be created between Web Services and
Semantic Web technologies to provide a new generation of eservices.
Abstract: This paper presents a design and prototype
implementation of new home automation system that uses WiFi
technology as a network infrastructure connecting its parts. The
proposed system consists of two main components; the first part is
the server (web server), which presents system core that manages,
controls, and monitors users- home. Users and system administrator
can locally (LAN) or remotely (internet) manage and control system
code. Second part is hardware interface module, which provides
appropriate interface to sensors and actuator of home automation
system. Unlike most of available home automation system in the
market the proposed system is scalable that one server can manage
many hardware interface modules as long as it exists on WiFi
network coverage. System supports a wide range of home
automation devices like power management components, and
security components. The proposed system is better from the
scalability and flexibility point of view than the commercially
available home automation systems.
Abstract: The Bangalore City is facing the acute problem of
pollution in the atmosphere due to the heavy increase in the traffic
and developmental activities in recent years. The present study is an
attempt in the direction to assess trend of the ambient air quality
status of three stations, viz., AMCO Batteries Factory, Mysore Road,
GRAPHITE INDIA FACTORY, KHB Industrial Area, Whitefield
and Ananda Rao Circle, Gandhinagar with respect to some of the
major criteria pollutants such as Total Suspended particular matter
(SPM), Oxides of nitrogen (NOx), and Oxides of sulphur (SO2). The
sites are representative of various kinds of growths viz., commercial,
residential and industrial, prevailing in Bangalore, which are
contributing to air pollution. The concentration of Sulphur Dioxide
(SO2) at all locations showed a falling trend due to use of refined
petrol and diesel in the recent years. The concentration of Oxides of
nitrogen (NOx) showed an increasing trend but was within the
permissible limits. The concentration of the Suspended particular
matter (SPM) showed the mixed trend. The correlation between
model and observed values is found to vary from 0.4 to 0.7 for SO2,
0.45 to 0.65 for NOx and 0.4 to 0.6 for SPM. About 80% of data is
observed to fall within the error band of ±50%. Forecast test for the
best fit models showed the same trend as actual values in most of the
cases. However, the deviation observed in few cases could be
attributed to change in quality of petro products, increase in the
volume of traffic, introduction of LPG as fuel in many types of
automobiles, poor condition of roads, prevailing meteorological
conditions, etc.
Abstract: In this paper we analyze the core issues affecting
software architecture in enterprise projects where a large number of
people at different backgrounds are involved and complex business,
management and technical problems exist. We first give general
features of typical enterprise projects and then present foundations of
software architectures. The detailed analysis of core issues affecting
software architecture in software development phases is given. We
focus on three main areas in each development phase: people,
process, and management related issues, structural (product) issues,
and technology related issues. After we point out core issues and
problems in these main areas, we give recommendations for
designing good architecture. We observed these core issues and the
importance of following the best software development practices and
also developed some novel practices in many big enterprise
commercial and military projects in about 10 years of experience.
Abstract: The necessity of accurate and timely field data is
shared among organizations engaged in fundamentally different
activities, public services or commercial operations. Basically, there
are three major components in the process of the qualitative research:
data collection, interpretation and organization of data, and analytic
process. Representative technological advancements in terms of
innovation have been made in mobile devices (mobile phone, PDA-s,
tablets, laptops, etc). Resources that can be potentially applied on the
data collection activity for field researches in order to improve this
process.
This paper presents and discuss the main features of a mobile
phone based solution for field data collection, composed of basically
three modules: a survey editor, a server web application and a client
mobile application. The data gathering process begins with the
survey creation module, which enables the production of tailored
questionnaires. The field workforce receives the questionnaire(s) on
their mobile phones to collect the interviews responses and sending
them back to a server for immediate analysis.
Abstract: Multifunctional structures are a potentially disruptive
technology that allows for significant mass savings on spacecraft.
The specific concept addressed herein is that of a multifunctional
power structure. In this paper, a parametric optimisation of the
design of such a structure that uses commercially available battery
cells is presented. Using numerical modelling, it was found that there
exists several trade-offs aboutthe conflict between the capacity of the
panel and its mechanical properties. It was found that there is no
universal optimal location for the cells. Placing them close to the
mechanical interfaces increases loading in the mechanically weak
cells whereas placing them at the centre of the panel increases the
stress inthe panel and reduces the stiffness of the structure.
Abstract: This paper suggests a rethinking of the existing
research about Genetically Modified (GM) food. Since the first batch
of GM food was commercialised in the UK market, GM food rapidly
received and lost media attention in the UK. Disagreement on GM
food policy between the US and the EU has also drawn scholarly
attention to this issue. Much research has been carried out intending to
understand people-s views about GM food and the shaping of these
views. This paper was based on the data collected in twenty-nine
semi-structured interviews, which were examined through Erving
Goffman-s idea of self-presentation in interactions to suggest that the
existing studies investigating “consumer attitudes" towards GM food
have only considered the “front stage" in the dramaturgic metaphor.
This paper suggests that the ways in which people choose to present
themselves when participating these studies should be taken into
account during the data analysis.
Abstract: This paper describes the shape optimization of impeller
blades for a anti-heeling bidirectional axial flow pump used in ships.
In general, a bidirectional axial pump has an efficiency much lower
than the classical unidirectional pump because of the symmetry of the
blade type. In this paper, by focusing on a pump impeller, the shape of
blades is redesigned to reach a higher efficiency in a bidirectional axial
pump. The commercial code employed in this simulation is CFX v.13.
CFD result of pump torque, head, and hydraulic efficiency was
compared. The orthogonal array (OA) and analysis of variance
(ANOVA) techniques and surrogate model based optimization using
orthogonal polynomial, are employed to determine the main effects
and their optimal design variables. According to the optimal design,
we confirm an effective design variable in impeller blades and explain
the optimal solution, the usefulness for satisfying the constraints of
pump torque and head.
Abstract: This paper proposes new algorithms for the computeraided
design and manufacture (CAD/CAM) of 3D woven multi-layer
textile structures. Existing commercial CAD/CAM systems are often
restricted to the design and manufacture of 2D weaves. Those
CAD/CAM systems that do support the design and manufacture of
3D multi-layer weaves are often limited to manual editing of design
paper grids on the computer display and weave retrieval from stored
archives. This complex design activity is time-consuming, tedious
and error-prone and requires considerable experience and skill of a
technical weaver. Recent research reported in the literature has
addressed some of the shortcomings of commercial 3D multi-layer
weave CAD/CAM systems. However, earlier research results have
shown the need for further work on weave specification, weave
generation, yarn path editing and layer binding. Analysis of 3D
multi-layer weaves in this research has led to the design and
development of efficient and robust algorithms for the CAD/CAM of
3D woven multi-layer textile structures. The resulting algorithmically
generated weave designs can be used as a basis for lifting plans that
can be loaded onto looms equipped with electronic shedding
mechanisms for the CAM of 3D woven multi-layer textile structures.
Abstract: This paper investigates experimental and numerical study of the airflow characteristics for vortex, round and square ceiling diffusers and its effect on the thermal comfort in a ventilated room. Three different thermal comfort criteria namely; Mean Age of the Air (MAA), ventilation effectiveness (E), and Effective Draft Temperature (EDT) have been used to predict the thermal comfort zone inside the room. In experimental work, a sub-scale room is set-up to measure the temperature field in the room. In numerical analysis, unstructured grids have been used to discretize the numerical domain. Conservation equations are solved using FLUENT commercial flow solver. The code is validated by comparing the numerical results obtained from three different turbulence models with the available experimental data. The comparison between the various numerical models shows that the standard k-ε turbulence model can be used to simulate these cases successfully. After validation of the code, effect of supply air velocity on the flow and thermal field could be investigated and hence the thermal comfort. The results show that the pressure coefficient created by the square diffuser is 1.5 times greater than that created by the vortex diffuser. The velocity decay coefficient is nearly the same for square and round diffusers and is 2.6 times greater than that for the vortex diffuser.
Abstract: A. niger XP isolated from Vietnam produces very low amount of acidic phytase with optimal pH at 2.5 and 5.5. The phytase production of this strain was successfully improved through gene cloning and expression. A 1.4 - kb DNA fragment containing the coding region of the phyA gene was amplified by PCR and inserted into the expression vector pPICZαA with a signal peptide α- factor, under the control of AOX1 promoter. The recombined plasmid was transformed into the host strain P. pastoris KM71H and X33 by electroporation. Both host strains could efficiently express and secret phytase. The multicopy strains were screened for over expression of phytase. All the selected multicopy strains of P. pastoris X33 were examined for phytase activity, the maximum phytase yield of 1329 IU/ml was obtained after 4 days of incubation in medium BMM. The recombinant protein with MW of 97.4 KW showed to be the only one protein secreted in the culture broth. Multicopy transformant P. pastoris X33 supposed to be potential candidate for producing the commercial preparation of phytase.
Abstract: Location-based services (LBS) exploit the known
location of a user to provide services dependent on their geographic
context and personalized needs [1].
The development and arrival of broadband mobile data networks
supported with mobile terminals equipped with new location
technologies like GPS have finally created opportunities for
implementation of LBS applications. But, from the other side,
collecting location information data in general raises privacy
concerns.
This paper presents results from two surveys of LBS acceptance in
Croatia. The first survey was administered on 181 students, and the
second extended survey involved pattern of 180 Croatian citizens.
We developed questionnaire which consists of descriptions of 15
different applications with scale which measures perceptions and
attitudes of users towards these applications.
We report the results to identify potential commercial applications
for LBS in B2C segment. Our findings suggest that some types of
applications like emergency&safety services and navigation have
significantly higher rate of acceptance than other types.