Abstract: The utilize of renewable energy sources becomes
more crucial and fascinatingly, wider application of renewable
energy devices at domestic, commercial and industrial levels is not
only affect to stronger awareness but also significantly installed
capacities. Moreover, biomass principally is in form of woods and
converts to be energy for using by humans for a long time.
Gasification is a process of conversion of solid carbonaceous fuel
into combustible gas by partial combustion. Many gasified models
have various operating conditions because the parameters kept in
each model are differentiated. This study applied the experimental
data including three inputs variables including biomass consumption;
temperature at combustion zone and ash discharge rate and gas flow
rate as only one output variable. In this paper, response surface
methods were applied for identification of the gasified system
equation suitable for experimental data. The result showed that linear
model gave superlative results.
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.
Abstract: Microcirculation is essential for the proper supply of
oxygen and nutritive substances to the biological tissue and the
removal of waste products of metabolism. The determination of
blood flow in the capillaries is therefore of great interest to clinicians.
A comparison has been carried out using the developed non-invasive,
non-contact and whole field laser speckle contrast imaging (LSCI)
based technique and as well as a commercially available laser
Doppler blood flowmeter (LDF) to evaluate blood flow at the finger
tip and elbow and is presented here. The LSCI technique gives more
quantitative information on the velocity of blood when compared to
the perfusion values obtained using the LDF. Measurement of blood
flow in capillaries can be of great interest to clinicians in the
diagnosis of vascular diseases of the upper extremities.
Abstract: Recently, wireless sensor networks have been paid
more interest, are widely used in a lot of commercial and military
applications, and may be deployed in critical scenarios (e.g. when a
malfunctioning network results in danger to human life or great
financial loss). Such networks must be protected against human
intrusion by using the secret keys to encrypt the exchange messages
between communicating nodes. Both the symmetric and asymmetric
methods have their own drawbacks for use in key management. Thus,
we avoid the weakness of these two cryptosystems and make use of
their advantages to establish a secure environment by developing the
new method for encryption depending on the idea of code
conversion. The code conversion-s equations are used as the key for
designing the proposed system based on the basics of logic gate-s
principals. Using our security architecture, we show how to reduce
significant attacks on wireless sensor networks.
Abstract: A ten-year grazing study was conducted at the
Agriculture and Agri-Food Canada Brandon Research Centre in
Manitoba to study the effect of alfalfa inclusion and fertilizer (N, P,
K, and S) addition on economics and efficiency of non-renewable
energy use in meadow brome grass-based pasture systems for beef
production. Fertilizing grass-only or alfalfa-grass pastures to full soil
test recommendations improved pasture productivity, but did not
improve profitability compared to unfertilized pastures. Fertilizing
grass-only pastures resulted in the highest net loss of any pasture
management strategy in this study. Adding alfalfa at the time of
seeding, with no added fertilizer, was economically the best pasture
improvement strategy in this study. Because of moisture limitations,
adding commercial fertilizer to full soil test recommendations is
probably not economically justifiable in most years, especially with
the rising cost of fertilizer. Improving grass-only pastures by adding
fertilizer and/or alfalfa required additional non-renewable energy
inputs; however, the additional energy required for unfertilized
alfalfa-grass pastures was minimal compared to the fertilized
pastures. Of the four pasture management strategies, adding alfalfa
to grass pastures without adding fertilizer had the highest efficiency
of energy use. Based on energy use and economic performance, the
unfertilized alfalfa-grass pasture was the most efficient and
sustainable pasture system.
Abstract: Pretreatment of lignocellulosic biomass materials from
poplar, acacia, oak, and fir with different ionic liquids (ILs)
containing 1-alkyl-3-methyl-imidazolium cations and various anions
has been carried out. The dissolved cellulose from biomass was
precipitated by adding anti-solvents into the solution and vigorous
stirring. Commercial cellulases Celluclast 1.5L and Accelerase 1000
have been used for hydrolysis of untreated and pretreated
lignocellulosic biomass. Among the tested ILs, [Emim]COOCH3
showed the best efficiency, resulting in highest amount of liberated
reducing sugars. Pretreatment of lignocellulosic biomass using
glycerol-ionic liquids combined pretreatment and dilute acid-ionic
liquids combined pretreatment were evaluated and compared with
glycerol pretreatment, ionic liquids pretreatment and dilute acid
pretreatment.
Abstract: In recent years, there has been an increasing interest
toward the use of bovine genotyped embryos for commercial embryo
transfer programs. Biopsy of a few cells in morulla stage is essential
for preimplantation genetic diagnosis (PGD). Low amount of DNA
have limited performing the several molecular analyses within PGD
analyses. Whole genome amplification (WGA) promises to eliminate
this problem. We evaluated the possibility and performance of an
improved primer extension preamplification (I-PEP) method with a
range of starting bovine genomic DNA from 1-8 cells into the WGA
reaction. We optimized a short and simple I-PEP (ssI-PEP) procedure
(~3h). This optimized WGA method was assessed by 6 loci specific
polymerase chain reactions (PCRs), included restriction fragments
length polymorphism (RFLP). Optimized WGA procedure possesses
enough sensitivity for molecular genetic analyses through the few
input cells. This is a new era for generating characterized bovine
embryos in preimplantation stage.
Abstract: Biodiesel production with used frying by
transesterification reaction with methanol, using a commercial
kaolinite thermally-activated solid acid catalyst was investigated.
The surface area, the average pore diameter and pore volume of the
kaolinite catalyst were 10 m2/g, 13.0 nm and 30 mm3/g, respectively.
The optimal conditions for the transesterification reaction were
determined to be oil/methanol, in a molar ratio 1:31, temperature 160
ºC and catalyst concentration of 3% (w/w). The yield of fatty acids
methyl esters (FAME) was 92.4% after 2 h of reaction. This method
of preparation of biodiesel can be a positive alternative for utilizing
used frying corn oil for feedstock of biodiesel combined with the
inexpensive catalyst.
Abstract: Memory Errors Detection and Correction aim to secure the transaction of data between the central processing unit of a satellite onboard computer and its local memory. In this paper, the application of a double-bit error detection and correction method is described and implemented in Field Programmable Gate Array (FPGA) technology. The performance of the proposed EDAC method is measured and compared with two different EDAC devices, using the same FPGA technology. Statistical analysis of single-event upset (SEU) and multiple-bit upset (MBU) activity in commercial memories onboard the first Algerian microsatellite Alsat-1 is given.
Abstract: In the current study we present a system that is
capable to deliver proxy based differentiated service. It will help the
carrier service node to sell a prepaid service to clients and limit the
use to a particular mobile device or devices for a certain time. The
system includes software and hardware architecture for a mobile
device with moderate computational power, and a secure protocol for
communication between it and its carrier service node. On the
carrier service node a proxy runs on a centralized server to be
capable of implementing cryptographic algorithms, while the mobile
device contains a simple embedded processor capable of executing
simple algorithms. One prerequisite is needed for the system to run
efficiently that is a presence of Global Trusted Verification Authority
(GTVA) which is equivalent to certifying authority in IP networks.
This system appears to be of great interest for many commercial
transactions, business to business electronic and mobile commerce,
and military applications.
Abstract: A thirty Rahmani weaned male lambs of average body weight (27.28±1.40 kg) were randomly allotted to three similar groups, ten lambs in each, to study the benefit of commercial feed additives Tonilisat (Saccharomyces cerevisiae) and Roemin W2 (Lactobacillus acidophilus, Lactobacillus thermophilus, Bifidobacterium and Lactose) as growth promoters on lambs performance, digestibility, rumen activity and some blood constituents. The experiment lasted about 107 days. Three experimental groups were allotted as control group: received the basal ration, T1 group: received the basal ration supplemented with Tonilisat as (0.5kg/ ton concentrate feed mixture) and T2 group: received the basal ration supplemented with Roemin W2 (1kg/ ton concentrate feed mixture). Our study revealed that addition of Tonilisat significantly increased digestion coefficient of crude protein than that of the control group, Furthermore, the supplementation of Tonilisat or Roemin W2 increased (p
Abstract: Induction motors are being used in greater numbers
throughout a wide variety of industrial and commercial applications
because it provides many benefits and reliable device to convert the
electrical energy into mechanical motion. In some application it-s
desired to control the speed of the induction motor. Because of the
physics of the induction motor the preferred method of controlling its
speed is to vary the frequency of the AC voltage driving the motor. In
recent years, with the microcontroller incorporated into an appliance
it becomes possible to use it to generate the variable frequency AC
voltage to control the speed of the induction motor.
This study investigates the microcontroller based variable
frequency power inverter. the microcontroller is provide the variable
frequency pulse width modulation (PWM) signal that control the
applied voltage on the gate drive, which is provides the required
PWM frequency with less harmonics at the output of the power
inverter.
The fully controlled bridge voltage source inverter has been
implemented with semiconductors power devices isolated gate
bipolar transistor (IGBT), and the PWM technique has been
employed in this inverter to supply the motor with AC voltage.
The proposed drive system for three & single phase power inverter
is simulated using Matlab/Simulink. The Matlab Simulation Results
for the proposed system were achieved with different SPWM. From
the result a stable variable frequency inverter over wide range has
been obtained and a good agreement has been found between the
simulation and hardware of a microcontroller based single phase
inverter.
Abstract: In this study, stress distributions on dental implants
made of functionally graded biomaterials (FGBM) are investigated
numerically. The implant body is considered to be subjected to axial
compression loads. Numerical problem is assumed to be 2D, and
ANSYS commercial software is used for the analysis. The cross
section of the implant thread varies as varying the height (H) and the
width (t) of the thread. According to thread dimensions of implant
and material properties of FGBM, equivalent stress distribution on
the implant is determined and presented with contour plots along
with the maximum equivalent stress values. As a result, with
increasing material gradient parameter (n), the equivalent stress
decreases, but the minimum stress distribution increases. Maximum
stress values decrease with decreasing implant radius (r). Maximum
von Mises stresses increases with decreasing H when t is constant.
On the other hand, the stress values are not affected by variation of t
in the case of H = constant.
Abstract: Xanthan gum is one of the major commercial
biopolymers. Due to its excellent rheological properties xanthan gum
is used in many applications, mainly in food industry. Commercial
production of xanthan gum uses glucose as the carbon substrate;
consequently the price of xanthan production is high. One of the
ways to decrease xanthan price, is using cheaper substrate like
agricultural wastes. Iran is one of the biggest date producer countries.
However approximately 50% of date production is wasted annually.
The goal of this study is to produce xanthan gum from waste date
using Xanthomonas campestris PTCC1473 by submerged
fermentation. In this study the effect of three variables including
phosphor and nitrogen amount and agitation rate in three levels using
response surface methodology (RSM) has been studied. Results
achieved from statistical analysis Design Expert 7.0.0 software
showed that xanthan increased with increasing level of phosphor.
Low level of nitrogen leaded to higher xanthan production. Xanthan
amount, increasing agitation had positive influence. The statistical
model identified the optimum conditions nitrogen amount=3.15g/l,
phosphor amount=5.03 g/l and agitation=394.8 rpm for xanthan. To
model validation, experiments in optimum conditions for xanthan
gum were carried out. The mean of result for xanthan was 6.72±0.26.
The result was closed to the predicted value by using RSM.
Abstract: This paper provides a key driver-based conceptual framework that can be used to improve a firm-s success in commercializing technology and in new product innovation resulting from collaboration with other organizations through strategic alliances. Based on a qualitative study using an interview approach, strategic alliances of entrepreneurs in the food processing industry in Thailand are explored. This paper describes factors affecting decisions to collaborate through alliances. It identifies four issues: maintaining the efficiency of the value chain for production capability, adapting to present and future competition, careful assessment of value of outcomes, and management of innovation. We consider five driving factors: resource orientation, assessment of risk, business opportunity, sharing of benefits and confidence in alliance partners. These factors will be of interest to entrepreneurs and policy makers with regard to further understanding of the direction of business strategies.
Abstract: The Long-range Energy and Alternatives Planning (LEAP) energy planning system has been developed for South Africa, for the 2005 base year and a limited number of plausible future scenarios that may have significant implications (negative or positive) in terms of environmental impacts. The system quantifies the national energy demand for the domestic, commercial, transport, industry and agriculture sectors, the supply of electricity and liquid fuels, and the resulting emissions. The South African National Energy Research Institute (SANERI) identified the need to develop an environmental assessment tool, based on the LEAP energy planning system, to provide decision-makers and stakeholders with the necessary understanding of the environmental impacts associated with different energy scenarios. A comprehensive analysis of indicators that are used internationally and in South Africa was done and the available data was accessed to select a reasonable number of indicators that could be utilized in energy planning. A consultative process was followed to determine the needs of different stakeholders on the required indicators and also the most suitable form of reporting. This paper demonstrates the application of Energy Environmental Sustainability Indicators (EESIs) as part of the developed tool, which assists with the identification of the environmental consequences of energy generation and use scenarios and thereby promotes sustainability, since environmental considerations can then be integrated into the preparation and adoption of policies, plans, programs and projects. Recommendations are made to refine the tool further for South Africa.
Abstract: This document describes an electronic speed control designed to drive two DC motors from a 6 V battery pack to be controlled by a commercial universal infrared remote control hand set. Conceived for a tank-like vehicle, one motor drives the left side wheels or tracks and the other motor drives the right side. As it is shown here, there is a left-right steering input and a forward– backward throttles input, like would be used on a model car. It is designed using a microcontroller PIC16F873A.
Abstract: The paper outlines the drivers behind the movement
from products to solutions in the Hi-Tech Business-to-Business
markets. The paper lists out the challenges in enabling the
transformation from products to solutions and also attempts to explore
strategic and operational recommendations based on the authors-
factual experiences with Japanese Hi-tech manufacturing
organizations. Organizations in the Hi-Tech Business-to-Business
markets are increasingly being compelled to move to a solutions model
from the conventional products model. Despite the added complexity
of solutions, successful technology commercialization can be achieved
by making prudent choices in defining a relevant solutions model, by
backing the solution model through appropriate organizational design,
and by overhauling the new product development process and
supporting infrastructure.
Abstract: Commercial infrastructures intended for use as leisure
retreats such as golf and ski resorts have been extensively developed in many rural areas of Japan. However, following the burst of the economic bubble in the 1990s, several existing resorts faced tough
management decisions and some were forced to close their business.
In this study, six alternative management options for restructuring the
existing golf courses (park, cemetery, biofuel production, reforestation,
pasturing and abandonment) are examined and their environmental
and economic impacts are quantitatively assessed. In addition,
restructuring scenarios of these options and an ex-ante assessment
model are developed. The scenario analysis by Monte Carlo simulation shows a clear trade-off between GHG savings and benefit/cost (B/C) ratios, of which “Restoring Nature" scenario
absorbs the most CO2 among the four scenarios considered, but its B/C
ratio is the lowest. This study can be used to select or examine options
and scenarios of golf course management and rural environmental
management policies.
Abstract: In this paper, we focus on the fusion of images from
different sources using multiresolution wavelet transforms. Based on
reviews of popular image fusion techniques used in data analysis,
different pixel and energy based methods are experimented. A novel
architecture with a hybrid algorithm is proposed which applies pixel
based maximum selection rule to low frequency approximations and
filter mask based fusion to high frequency details of wavelet
decomposition. The key feature of hybrid architecture is the
combination of advantages of pixel and region based fusion in a
single image which can help the development of sophisticated
algorithms enhancing the edges and structural details. A Graphical
User Interface is developed for image fusion to make the research
outcomes available to the end user. To utilize GUI capabilities for
medical, industrial and commercial activities without MATLAB
installation, a standalone executable application is also developed
using Matlab Compiler Runtime.