Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: Competitive relationships among Bradyrhizobium
japonicum USDA serogroup 123, 122 and 138 were screened versus
the standard commercial soybean variety Williams and two
introductions P1 377578 "671" in a field trial. Displacement of strain
123 by an effective strain should improved N2 fixation. Root nodules
were collected and strain occupancy percentage was determined
using strain specific fluorescent antibodies technique. As anticipated
the strain USDA 123 dominated 92% of nodules due to the high
affinity between the host and the symbiont. This dominance was
consistent and not changed materially either by inoculation practice
or by introducing new strainan. The interrelationship between the
genotype Williams and serogroup 122 & 138 was found very weak
although the cell density of the strain in the rhizosphere area was
equal. On the other hand, the nodule occupancy of genotypes 671 and
166 with rhizobia serogroup 123 was almost diminished to zero. .
The data further exhibited that the genotypes P1 671 and P1 166 have
high affinity to colonize with strains 122 and 138 whereas Williams
was highly promiscuous to strain 123.
Abstract: Phrases has a long history in information retrieval, particularly in commercial systems. Implicit semantic relationship between words in a form of BaseNP have shown significant improvement in term of precision in many IR studies. Our research focuses on linguistic phrases which is language dependent. Our results show that using BaseNP can improve performance although above 62% of words formation in Malay Language based on derivational affixes and suffixes.
Abstract: A novel methodology has been used to design an
evaporator coil of a refrigerant. The methodology used is through a
complete Computer Aided Design /Computer Aided Engineering
approach, by means of a Computational Fluid Dynamic/Finite
Element Analysis model which is executed many times for the
thermal-fluid exploration of several designs' configuration by an
commercial optimizer. Hence the design is carried out automatically
by parallel computations, with an optimization package taking the
decisions rather than the design engineer. The engineer instead takes
decision regarding the physical settings and initializing of the
computational models to employ, the number and the extension of the
geometrical parameters of the coil fins and the optimization tools to
be employed. The final design of the coil geometry found to be better
than the initial design.
Abstract: The complex structure of lignocellulose leads to great
difficulties in converting it to fermentable sugars for the ethanol
production. The major hydrolysis impediments are the crystallinity of
cellulose and the lignin content. To improve the efficiency of
enzymatic hydrolysis, microbial pretreatment of corncob was
investigated using two bacterial strains of Bacillus subtilis A 002 and
Cellulomonas sp. TISTR 784 (expected to break open the crystalline
part of cellulose) and lignin-degrading fungus, Phanerochaete
sordida SK7 (expected to remove lignin from lignocellulose). The
microbial pretreatment was carried out with each strain under its
optimum conditions. The pretreated corncob samples were further
hydrolyzed to produce reducing glucose with low amounts of
commercial cellulase (25 U·g-1 corncob) from Aspergillus niger. The
corncob samples were determined for composition change by X-ray
diffraction (XRD), Fourier transform infrared spectroscopy (FTIR),
and scanning electron microscope (SEM). According to the results,
the microbial pretreatment with fungus, P. sordida SK7 was the most
effective for enhancing enzymatic hydrolysis, approximately, 40%
improvement.
Abstract: commercially produced in Malaysia granular
palm shell activated carbon (PSAC) was biomodified with
bacterial biomass (Bacillus subtilis) to produce a hybrid
biosorbent of higher efficiency. The obtained biosorbent was
evaluated in terms of adsorption capacity to remove copper
and zinc metal ions from aqueous solutions. The adsorption
capacity was evaluated in batch adsorption experiments where
concentrations of metal ions varied from 20 to 350 mg/L. A
range of pH from 3 to 6 of aqueous solutions containing metal
ions was tested. Langmuir adsorption model was used to
interpret the experimental data. Comparison of the adsorption
data of the biomodified and original palm shell activated
carbon showed higher uptake of metal ions by the hybrid
biosorbent. A trend in metal ions uptake increase with the
increase in the solution-s pH was observed. The surface
characterization data indicated a decrease in the total surface
area for the hybrid biosorbent; however the uptake of copper
and zinc by it was at least equal to the original PSAC at pH 4
and 5. The highest capacity of the hybrid biosorbent was
observed at pH 5 and comprised 22 mg/g and 19 mg/g for
copper and zinc, respectively. The adsorption capacity at the
lowest pH of 3 was significantly low. The experimental results
facilitated identification of potential factors influencing the
adsorption of copper and zinc onto biomodified and original
palm shell activated carbon.
Abstract: Sweet potato products are necessary for the provision
of essential nutrients in every household, regardless of their poverty
status. Their consumption appears to be highly influenced by socioeconomic
factors, such as malnutrition, food insecurity and
unemployment. Therefore, market availability is crucial for these
cultivars to resolve some of the socio-economic factors. The aim of
the study was to investigate market availability of sweet potato
cultivars in the North West Province. In this study, both qualitative
and quantitative research methodologies were used. Qualitative
methodology was used to explain the quantitative outcomes of the
variables. On the other hand, quantitative results were used to test the
hypothesis. The study used SPSS software to analyse the data. Crosstabulation
and Chi-square statistics were used to obtain the
descriptive and inferential analyses, respectively. The study found
that the Blesbok cultivar is dominating the markets of the North West
Province, with the Monate cultivar dominating in the Bojanala
Platinum (75%) and Dr Ruth Segomotsi Mompati (25%) districts. It
is also found that a unit increase in the supply of sweet potato
cultivars in both local and district municipal markets is accompanied
by a reduced demand of 28% and 33% at district and local markets,
respectively. All these results were found to be significant at p
Abstract: On the basis of questionnaires and interviews of two samples of subjects (French and Anglo-Saxon) for which two food products were presented (one of the subject’s country and one of the foreign country), we have shown how consumers could be sensitive to the label or brand written on the package of the food product. Furthermore, in the light of Intersubjectivity theory, we have shown the necessity for the consumer to find congruence between the direct and meta perspective towards the product for which the producer and especially the marketer is responsible. Taking into account these findings may help to avoid the commercial failure of a brand while exported abroad.
Abstract: This paper presents a compact thermoelectric power generator system based on temperature difference across the element. The system can transfer the burning heat energy to electric energy directly. The proposed system has a thermoelectric generator and a power control box. In the generator, there are 4 thermoelectric modules (TEMs), each of which uses 2 thermoelectric chips (TEs) and 2 cold sinks, 1 thermal absorber, and 1 thermal conduction flat board. In the power control box, there are 1 storing energy device, 1 converter, and 1 inverter. The total net generating power is about 11W. This system uses commercial portable gas stoves or burns timber or the coal as the heat source, which is easily obtained. It adopts solid-state thermoelectric chips as heat inverter parts. The system has the advantages of being light-weight, quite, and mobile, requiring no maintenance, and havng easily-supplied heat source. The system can be used a as long as burning is allowed. This system works well for highly-mobilized outdoors situations by providing a power for illumination, entertainment equipment or the wireless equipment at refuge. Under heavy storms such as typhoon, when the solar panels become ineffective and the wind-powered machines malfunction, the thermoelectric power generator can continue providing the vital power.
Abstract: An optical fiber Fabry-Perot interferometer (FFPI) is
proposed and demonstrated for dynamic measurements in a
mechanical vibrating target. A polishing metal with a low reflectance
value adhered to a mechanical vibrator was excited via a function
generator at various excitation frequencies. Output interference
fringes were generated by modulating the reference and sensing
signal at the output arm. A fringe-counting technique was used for
interpreting the displacement information on the dedicated computer.
The fiber interferometer has been found the capability of the
displacement measurements of 1.28 μm – 96.01 μm. A commercial
displacement sensor was employed as a reference sensor for
investigating the measurement errors from the fiber sensor. A
maximum percentage measurement error of approximately 1.59 %
was obtained.
Abstract: The bypass exhaust system of a 160 MW combined cycle has been modeled and analyzed using numerical simulation in 2D prospective. Analysis was carried out using the commercial numerical simulation software, FLUENT 6.2. All inputs were based on the technical data gathered from working conditions of a Siemens V94.2 gas turbine, installed in the Yazd power plant. This paper deals with reduction of pressure drop in bypass exhaust system using turning vanes mounted in diverter box in order to alleviate turbulent energy dissipation rate above diverter box. The geometry of such turning vanes has been optimized based on the flow pattern at diverter box inlet. The results show that the use of optimized turning vanes in diverter box can improve the flow pattern and eliminate vortices around sharp edges just before the silencer. Furthermore, this optimization could decrease the pressure drop in bypass exhaust system and leads to higher plant efficiency.
Abstract: Off-grid Photovoltaic (PV) systems are empowering
technology in underdeveloped countries like Ethiopia where many
people live far away from the modern world. Where there is
relatively low energy consumption, providing energy from grid
systems is not commercially cost-effective. As a result, significant
people groups worldwide stay without access to electricity. One
remote village in northern Ethiopia was selected by the United
Nations for a pilot project to improve its living conditions. As part of
this comprehensive project, an intelligent charge controller circuit for
Off-grid PV systems was designed for the clinic in that village. In
this paper, design aspects of an intelligent charge controller unit and
its load driver circuits are discussed for an efficient utilization of PVbased
supply systems.
Abstract: In this study, the locations and areas of commercial
accumulations were detected by using digital yellow page data. An
original buffering method that can accurately create polygons of
commercial accumulations is proposed in this paper.; by using this
method, distribution of commercial accumulations can be easily
created and monitored over a wide area. The locations, areas, and
time-series changes of commercial accumulations in the South Kanto
region can be monitored by integrating polygons of commercial
accumulations with the time-series data of digital yellow page data.
The circumstances of commercial accumulations were shown to vary
according to areas, that is, highly- urbanized regions such as the city
center of Tokyo and prefectural capitals, suburban areas near large
cities, and suburban and rural areas.
Abstract: Recently, information security has become a key issue
in information technology as the number of computer security
breaches are exposed to an increasing number of security threats. A
variety of intrusion detection systems (IDS) have been employed for
protecting computers and networks from malicious network-based or
host-based attacks by using traditional statistical methods to new data
mining approaches in last decades. However, today's commercially
available intrusion detection systems are signature-based that are not
capable of detecting unknown attacks. In this paper, we present a
new learning algorithm for anomaly based network intrusion
detection system using decision tree algorithm that distinguishes
attacks from normal behaviors and identifies different types of
intrusions. Experimental results on the KDD99 benchmark network
intrusion detection dataset demonstrate that the proposed learning
algorithm achieved 98% detection rate (DR) in comparison with
other existing methods.
Abstract: Prior to 1975, women in Laos suffered from having
reduced levels of power over decision-making in their families and in
their communities. This has had a negative impact on their ability to
develop their own identities. Their roles were identified as being
responsible for household activities and making preparations for their
marriage. Many women lost opportunities to get educated and access
the outdoor work that might have empowered them to improve their
situations. So far, no accurate figures of either emigrants or return
migrants have been compiled but it appears that most of them were
women, and it was women who most and more frequently remitted
money home. However, very few recent studies have addressed the
relationship between remittances and the roles of women in Laos.
This study, therefore, aims at redressing to some extent the
deficiencies in knowledge. Qualitative techniques were used to gather
data, including individual in-depth interviews and direct observation
in combination with the content analysis method. Forty women in
Vientiane Municipality and Savannakhet province were individually
interviewed. It was found that the monetary remittance was typically
used for family security and well-being; on fungible activities; on
economic and business activities; and on community development,
especially concerning hospitality and providing daily household
necessities. Remittances played important roles in improving many
respondents- livelihoods and positively changed their identities in
families and communities. Women became empowered as they were
able to start commercial businesses, rather than taking care of (just)
housework, children and elders. Interviews indicated that 92.5% of
the respondents their quality of lives improved, 90% felt happier in
their families and 82.5% felt conflicts in their families were reduced.
Abstract: Heat pipes are used to control the thermal problem for
electronic cooling. It is especially difficult to dissipate heat to a heat
sink in an environment in space compared to earth. For solving this
problem, in this study, the Poiseuille (Po) number, which is the main
measure of the performance of a heat pipe, is studied by CFD; then, the
heat pipe performance is verified with experimental results. A heat
pipe is then fabricated for a spatial environment, and an in-house code
is developed. Further, a heat pipe subsystem, which consists of a heat
pipe, MLI (Multi Layer Insulator), SSM (Second Surface Mirror), and
radiator, is tested and correlated with the TMM (Thermal
Mathematical Model) through a commercial code. The correlation
results satisfy the 3K requirement, and the generated thermal model is
verified for application to a spatial environment.
Abstract: Bendability is constrained by maximum top roller
load imparting capacity of the machine. Maximum load is
encountered during the edge pre-bending stage of roller bending.
Capacity of 3-roller plate bending machine is specified by
maximum thickness and minimum shell diameter combinations that
can be pre-bend for given plate material of maximum width.
Commercially available plate width or width of the plate that can be
accommodated on machine decides the maximum rolling width.
Original equipment manufacturers (OEM) provide the machine
capacity chart based on reference material considering perfectly
plastic material model. Reported work shows the bendability analysis
of heavy duty 3-roller plate bending machine. The input variables for
the industry are plate thickness, shell diameter and material property
parameters, as it is fixed by the design. Analytical models of
equivalent thickness, equivalent width and maximum width based on
power law material model were derived to study the bendability.
Equation of maximum width provides bendability for designed
configuration i.e. material property, shell diameter and thickness
combinations within the machine limitations. Equivalent thicknesses
based on perfectly plastic and power law material model were
compared for four different materials grades of C-Mn steel in order
to predict the bend-ability. Effect of top roller offset on the
bendability at maximum top roller load imparting capacity is
reported.
Abstract: The more recent satellite projects/programs makes
extensive usage of real – time embedded systems. 16 bit processors
which meet the Mil-Std-1750 standard architecture have been used in
on-board systems. Most of the Space Applications have been written
in ADA. From a futuristic point of view, 32 bit/ 64 bit processors are
needed in the area of spacecraft computing and therefore an effort is
desirable in the study and survey of 64 bit architectures for space
applications. This will also result in significant technology
development in terms of VLSI and software tools for ADA (as the
legacy code is in ADA).
There are several basic requirements for a special processor for
this purpose. They include Radiation Hardened (RadHard) devices,
very low power dissipation, compatibility with existing operational
systems, scalable architectures for higher computational needs,
reliability, higher memory and I/O bandwidth, predictability, realtime
operating system and manufacturability of such processors.
Further on, these may include selection of FPGA devices, selection
of EDA tool chains, design flow, partitioning of the design, pin
count, performance evaluation, timing analysis etc.
This project deals with a brief study of 32 and 64 bit processors
readily available in the market and designing/ fabricating a 64 bit
RISC processor named RISC MicroProcessor with added
functionalities of an extended double precision floating point unit
and a 32 bit signal processing unit acting as co-processors. In this
paper, we emphasize the ease and importance of using Open Core
(OpenSparc T1 Verilog RTL) and Open “Source" EDA tools such as
Icarus to develop FPGA based prototypes quickly. Commercial tools
such as Xilinx ISE for Synthesis are also used when appropriate.
Abstract: Aroma forming volatiles are important components of
fermented beverages. The aim of current research is to evaluate the
volatile compounds and phenolic compounds of commercial ciders.
Volatile aroma compounds and TPC of seven commercial ciders
were determined. Extraction of aroma compounds was performed
using solid phase microextraction (DVB/Car/PDMS fibre). Analysis
of volatile aroma compounds was made using a Perkin Elmer Clarus
500 GC/MS. Total phenol content (TPC) was determined according
to the Folin-Ciocalteu spectrophotometric method and results were
expressed as gallic acid equivalents. The highest volatile compounds
were in apple ciders with pear flavor. The highest TPC and lower
content of volatile compounds were detected in French ciders.