Abstract: A design of communication area for infrared
electronic-toll-collection systems to provide an extended
communication interval in the vehicle traveling direction and
regular boundary between contiguous traffic lanes is proposed.
By utilizing two typical low-cost commercial infrared LEDs with
different half-intensity angles Φ1/2 = 22◦ and 10◦, the radiation
pattern of the emitter is designed to properly adjust the spatial
distribution of the signal power. The aforementioned purpose
can be achieved with an LED array in a three-piece structure
with appropriate mounting angles. With this emitter, the influence
of the mounting parameters, including the mounting height and
mounting angles of the on-board unit and road-side unit, on the
system performance in terms of the received signal strength and
communication area are investigated. The results reveal that, for
our emitter proposed in this paper, the ideal ”long-and-narrow”
characteristic of the communication area is very little affected by
these mounting parameters. An optimum mounting configuration is
also suggested.
Abstract: The production of activated carbon from low or zero cost of agricultural by-products or wastes has received great attention from academics and practitioners due to its economic and environmental benefits. In the production of bamboo furniture, a significant amount of bamboo waste is inevitably generated. Therefore, this research aimed to prepare activated carbons from bamboo furniture waste by chemical (KOH) activation and determine their properties and adsorption capacities for water treatment. The influence of carbonization time on the properties and adsorption capacities of activated carbons was also investigated. The finding showed that the bamboo-derived activated carbons had microporous characteristics. They exhibited high tendency for the reduction of impurities present in effluent water. Their adsorption capacities were comparable to the adsorption capacity of a commercial activated carbon regarding to the reduction in COD, TDS and turbidity of the effluent water.
Abstract: This paper presents a review on published literature
and experimental works on local sands for possible use as proppant,
specifically those from Terengganu coastal area. This includes
examination on characteristics of sand samples and selection of
experiments for proppant testing. Sand samples from identified areas
were tested according to particle size distribution, density, roundness
and sphericity, turbidity and mineralogy. Results from sand samples
were compared against proppant specifications set by API RP 56 and
selected commercial proppants. The present study found that the size
distribution, sphericity, turbidity and bulk density of Terengganu
sands are at par with some of commercial proppants. Nevertheless,
Terengganu sand samples do not completely surpass the required
roundness for use as proppant.
Abstract: One of the most important causes of accidents is
driver fatigue. To reduce the accidental rate, the driver needs a
quick nap when feeling sleepy. Hence, searching for the minimum
time period of nap is a very challenging problem. The purpose of
this paper is twofold, i.e. to investigate the possible fastest time
period for nap and its relationship with stage 2 sleep, and to
develop an automatic stage 2 sleep detection and alarm device. The
experiment for this investigation is designed with 21 subjects. It
yields the result that waking up the subjects after getting into stage
2 sleep for 3-5 minutes can efficiently reduce the sleepiness.
Furthermore, the automatic stage 2 sleep detection and alarm
device yields the real-time detection accuracy of approximately
85% which is comparable with the commercial sleep lab system.
Abstract: Computed tomography (CT) dosimetry normally uses
an ionization chamber 100 mm long to estimate the computed
tomography dose index (CTDI), however some reports have already
indicated that small devices could replace the long ion chamber to
improve quality assurance procedures in CT dosimetry. This paper
presents a novel dosimetry system based in a commercial
phototransistor evaluated for CT dosimetry. Three detector
configurations were developed for this system: with a single, two and
four devices. Dose profile measurements were obtained with them
and their angular response were evaluated. The results showed that
the novel dosimetry system with the phototransistor could be an
alternative for CT dosimetry. It allows to obtain the CT dose profile
in details and also to estimate the CTDI in longer length than the
100 mm pencil chamber. The angular response showed that the one
device detector configuration is the most adequate among the three
configurations analyzed in this study.
Abstract: The essential oil of M. × piperita L. was formulated
into a topical gel. The prepared gel was characterized for its pH,
viscosity, spreadiblity, consistency and extrudiblity, while its stability
was evaluated under different temperature conditions. The prepared
M. × piperita oil gel was clear and transparent. The pH value of
developed gel was 6.6, while its viscosity was 1200 cP. Spreadability
and consistency of the M. × piperita oil gel was 10.7 g.cm/sec and 7
mm, respectively. The prepared gel showed good extrudiblity. During
the stability studies, no significant change in pH and viscosity as a
function of time for gel was observed, indicating stability of prepared
formulation. The gel developed in this study is expected to forward
the usage of M. × piperita essential towards commercial application.
Abstract: This paper attempts to identify the significance of
Information and Communications Technology (ICT) and
competitiveness to the profit efficiency of commercial banks in
Malaysia. The profit efficiency of commercial banks in Malaysia, the
dependent variable, was estimated using the Stochastic Frontier
Approach (SFA) on a sample of unbalanced panel data, covering 23
commercial banks, between 1995 to 2007. Based on the empirical
results, ICT was not found to exert a significant impact on profit
efficiency, whereas competitiveness, non ICT stock expenditure and
ownership were significant contributors. On the other hand, the size
of banks was found to have significantly reduced profit efficiency,
opening up for various interpretations of the interrelated role of ICT
and competition.
Abstract: This interdisciplinary study is an investigation to evaluate user-interfaces in business administration. The study is going to be implemented on two computerized business administration systems with two distinctive user-interfaces, so that differences between the two systems can be determined. Both systems, a commercial and a prototype developed for the purpose of this study, deal with ordering of supplies, tendering procedures, issuing purchase orders, controlling the movement of the stocks against their actual balances on the shelves and editing them on their tabulations. In the second suggested system, modern computer graphics and multimedia issues were taken into consideration to cover the drawbacks of the first system. To highlight differences between the two investigated systems regarding some chosen standard quality criteria, the study employs various statistical techniques and methods to evaluate the users- interaction with both systems. The study variables are divided into two divisions: independent representing the interfaces of the two systems, and dependent embracing efficiency, effectiveness, satisfaction, error rate etc.
Abstract: Today-s Voltage Regulator Modules (VRMs) face increasing design challenges as the number of transistors in microprocessors increases per Moore-s Law. These challenges have recently become even more demanding as microprocessors operate at sub voltage range at significantly high current. This paper presents a new multiphase topology with cell configuration for improved performance in low voltage and high current applications. A lab scale hardware prototype of the new topology was design and constructed. Laboratory tests were performed on the proposed converter and compared with a commercially available VRM. Results from the proposed topology exhibit improved performance compared to the commercially available counterpart.
Abstract: This paper presents the optimal controller design of
the generator control unit in the aircraft power system. The adaptive
tabu search technique is applied to tune the controller parameters
until the best terminal output voltage of generator is achieved. The
output response from the system with the controllers designed by the
proposed technique is compared with those from the conventional
method. The transient simulations using the commercial software
package show that the controllers designed from the adaptive tabu
search algorithm can provide the better output performance compared
with the result from the classical method. The proposed design
technique is very flexible and useful for electrical aircraft engineers.
Abstract: Message Passing Interface is widely used for Parallel
and Distributed Computing. MPICH and LAM are popular open
source MPIs available to the parallel computing community also
there are commercial MPIs, which performs better than MPICH etc.
In this paper, we discuss a commercial Message Passing Interface, CMPI
(C-DAC Message Passing Interface). C-MPI is an optimized
MPI for CLUMPS. It is found to be faster and more robust compared
to MPICH. We have compared performance of C-MPI and MPICH
on Gigabit Ethernet network.
Abstract: Most of the collision warning systems currently
available in the automotive market are mainly designed to warn
against imminent rear-end and lane-changing collisions. No collision
warning system is commercially available to warn against imminent
turning collisions at intersections, especially for left-turn collisions
when a driver attempts to make a left-turn at either a signalized or
non-signalized intersection, conflicting with the path of other
approaching vehicles traveling on the opposite-direction traffic
stream. One of the major factors that lead to left-turn collisions is the
human error and misjudgment of the driver of the turning vehicle
when perceiving the speed and acceleration of other vehicles
traveling on the opposite-direction traffic stream; therefore, using a
properly-designed collision warning system will likely reduce, or
even eliminate, this type of collisions by reducing human error. This
paper introduces perceptual framework for a proposed collision
warning system that can detect imminent left-turn collisions at
intersections. The system utilizes a commercially-available detection
sensor (either a radar sensor or a laser detector) to detect approaching
vehicles traveling on the opposite-direction traffic stream and
calculate their speeds and acceleration rates to estimate the time-tocollision
and compare that time to the time required for the turning
vehicle to clear the intersection. When calculating the time required
for the turning vehicle to clear the intersection, consideration is given
to the perception-reaction time of the driver of the turning vehicle,
which is the time required by the driver to perceive the message
given by the warning system and react to it by engaging the throttle.
A regression model was developed to estimate perception-reaction
time based on age and gender of the driver of the host vehicle.
Desired acceleration rate selected by the driver of the turning vehicle,
when making the left-turn movement, is another human factor that is
considered by the system. Another regression model was developed
to estimate the acceleration rate selected by the driver of the turning
vehicle based on driver-s age and gender as well as on the location
and speed of the nearest approaching vehicle along with the
maximum acceleration rate provided by the mechanical
characteristics of the turning vehicle. By comparing time-to-collision
with the time required for the turning vehicle to clear the intersection,
the system displays a message to the driver of the turning vehicle
when departure is safe. An application example is provided to
illustrate the logic algorithm of the proposed system.
Abstract: Robots- visual perception is a field that is gaining
increasing attention from researchers. This is partly due to emerging
trends in the commercial availability of 3D scanning systems or
devices that produce a high information accuracy level for a variety of
applications. In the history of mining, the mortality rate of mine workers
has been alarming and robots exhibit a great deal of potentials to
tackle safety issues in mines. However, an effective vision system
is crucial to safe autonomous navigation in underground terrains.
This work investigates robots- perception in underground terrains
(mines and tunnels) using statistical region merging (SRM) model.
SRM reconstructs the main structural components of an imagery
by a simple but effective statistical analysis. An investigation is
conducted on different regions of the mine, such as the shaft, stope
and gallery, using publicly available mine frames, with a stream of
locally captured mine images. An investigation is also conducted on a
stream of underground tunnel image frames, using the XBOX Kinect
3D sensors. The Kinect sensors produce streams of red, green and
blue (RGB) and depth images of 640 x 480 resolution at 30 frames per
second. Integrating the depth information to drivability gives a strong
cue to the analysis, which detects 3D results augmenting drivable and
non-drivable regions in 2D. The results of the 2D and 3D experiment
with different terrains, mines and tunnels, together with the qualitative
and quantitative evaluation, reveal that a good drivable region can be
detected in dynamic underground terrains.
Abstract: In this paper, we propose a geometric modeling of
illumination on the patterned image containing etching transistor. This
image is captured by a commercial camera during the inspection of
a TFT-LCD panel. Inspection of defect is an important process in the
production of LCD panel, but the regional difference in brightness,
which has a negative effect on the inspection, is due to the uneven
illumination environment. In order to solve this problem, we present
a geometric modeling of illumination consisting of an interpolation
using the least squares method and 3D modeling using bezier surface.
Our computational time, by using the sampling method, is shorter
than the previous methods. Moreover, it can be further used to correct
brightness in every patterned image.
Abstract: In this research, effort was made to identify and
evaluate barriers to the development of entrepreneurship among
Iranian entrepreneur women who were graduated from universities.
In this study, perspectives of thirty-seven available entrepreneur
women were examined. In order to prepare questionnaires and
receive knowledge about barriers among these women, seven cases of
entrepreneur women took part in in-depth interviews. Then, to
evaluate the importance of barriers, the researchers made a
questionnaire with closed questions in which the barriers were
classified into the following categories: personal-familial barriers;
socio-cultural barriers; economic-financial-commercial barriers; and
structural barriers. Entrepreneur women were requested to rate the
importance of each item. The results indicated that there were
different obstacles among entrepreneur women. The order of the
important barriers was as fallow: economic-financial-commercial,
structural, socio-cultural, and personal-familial.
Abstract: Majority of pepper farmers in Malaysia are using the
open-sun method for drying the pepper berries. This method is time
consuming and exposed the berries to rain and contamination. A
maintenance-friendly and properly enclosed dryer is therefore
desired. A dryer design with a solar collector and a chimney was
studied and adapted to suit the needs of small-scale pepper farmers in
Malaysia. The dryer will provide an environment with an optimum
operating temperature meant for drying pepper berries. The dryer
model was evaluated by using commercially available computational
fluid dynamic (CFD) software in order to understand the heat and
mass transfer inside the dryer. Natural convection was the only mode
of heat transportation considered in this study as in accordance to the
idea of having a simple and maintenance-friendly design. To
accommodate the effect of low buoyancy found in natural convection
driers, a biomass burner was integrated into the solar dryer design.
Abstract: Consumer demand for products with low fat or sugar content and low levels of food additives, as well as cost factors, make exopolysaccharides (EPS) a viable alternative. EPS remain an interesting tool to modulate the sensory properties of yoghurt. This study was designed to evaluate EPS production potential of commercial yoghurt starter cultures (Yo-Flex starters: Harmony 1.0, TWIST 1.0 and YF-L902, Chr.Hansen, Denmark) and their influence on an apparent viscosity of yoghurt samples. The production of intracellularly synthesized EPS by different commercial yoghurt starters varies roughly from 144,08 to 440,81 mg/l. Analysing starters’ producing EPS, they showed large variations in concentration and supposedly composition. TWIST 1.0 had produced greater amounts of EPS in MRS medium and in yoghurt samples but there wasn’t determined significant contribution to development of texture as well as an apparent viscosity of the final product. YF-L902 and Harmony 1.0 starters differed considerably in EPS yields, but not in apparent viscosities (p>0.05) of the final yoghurts. Correlation between EPS concentration and viscosity of yoghurt samples was not established in the study.
Abstract: This paper presents a low cost automatic system for
sampling the electric field in a limited area. The scanning area is a
flat surface parallel to the ground at a selected height. We discuss
in detail the hardware, software and all the arrangements involved
in the system operation. In order to show the system performance
we include a campaign of narrow band measurements with 6017
sample points in the surroundings of a cellular base station. A
commercial isotropic antenna with three orthogonal axes was used
as sampling device. The results are analyzed in terms of its space
average, standard deviation and statistical distribution.
Abstract: This paper presents positive and negative full-wave
rectifier. The proposed structure is based on OTA using
commercially available ICs (LT1228). The features of the proposed
circuit are that: it can rectify and amplify voltage signal with
controllable output magnitude via input bias current: the output
voltage is free from temperature variation. The circuit description
merely consists of 1 single ended and 3 fully differential OTAs. The
performance of the proposed circuit are investigated though PSpice.
They show that the proposed circuit can function as positive/negative
full-wave rectifier, where the voltage input wide-dynamic range from
-5V to 5V. Furthermore, the output voltage is slightly dependent on
the temperature variations.
Abstract: This paper presents a simple and sensitive kinetic
spectrophotometric method for the determination of ramipril in
commercial dosage forms. The method is based on the reaction of the
drug with 1-chloro-2,4-dinitrobenzene (CDNB) in dimethylsulfoxide
(DMSO) at 100 ± 1ºC. The reaction is followed
spectrophotometrically by measuring the rate of change of the
absorbance at 420 nm. Fixed-time (ΔA) and equilibrium methods are
adopted for constructing the calibration curves. Both the calibration
curves were found to be linear over the concentration ranges 20 - 220
μg/ml. The regression analysis of calibration data yielded the linear
equations: Δ A = 6.30 × 10-4 + 1.54 × 10-3 C and A = 3.62 × 10-4 +
6.35 × 10-3 C for fixed time (Δ A) and equilibrium methods,
respectively. The limits of detection (LOD) for fixed time and
equilibrium methods are 1.47 and 1.05 μg/ml, respectively. The
method has been successfully applied to the determination of ramipril
in commercial dosage forms. Statistical comparison of the results
shows that there is no significant difference between the proposed
methods and Abdellatef-s spectrophotometric method.