Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: The use of wind energy for electricity generation is
growing rapidly across the world and in Portugal. However, the
geographical characteristics of the country along with the average
wind regime and with the environmental restrictions imposed to these
projects create limitations to the exploit of the onshore wind
resource. The best onshore wind spots are already committed and the
possibility of offshore wind farms in the Portuguese cost is now
being considered. This paper aims to make a contribution to the
evaluation of offshore wind power projects in Portugal. The technical
restrictions are addressed and the strategic, environmental and
financial interest of the project is analysed from the private company
and public points of view. The results suggest that additional support
schemes are required to ensure private investors interest for these
projects. Assuming an approach of direct substitution of energy
sources for electricity generation, the avoided CO2 equivalent
emissions for an offshore wind power project were quantified. Based
on the conclusions, future research is proposed to address the
environmental and social impacts of these projects.
Abstract: In this paper, we first give the representation of the general solution of the following inverse eigenvalue problem (IEP): Given X ∈ Rn×p and a diagonal matrix Λ ∈ Rp×p, find nontrivial real-valued symmetric arrow-head matrices A and B such that AXΛ = BX. We then consider an optimal approximation problem: Given real-valued symmetric arrow-head matrices A, ˜ B˜ ∈ Rn×n, find (A, ˆ Bˆ) ∈ SE such that Aˆ − A˜2 + Bˆ − B˜2 = min(A,B)∈SE (A−A˜2 +B −B˜2), where SE is the solution set of IEP. We show that the optimal approximation solution (A, ˆ Bˆ) is unique and derive an explicit formula for it.
Abstract: Microstrip antennas are conformable to planar and
nonplanar surfaces, simple and inexpensive to fabricate using modern
printed-circuit technology. Circular polarization of low-profile
microstrip patch with high bandwidth is achieved in this research
through the use of a three-cross-arms branch-line coupler with
sequential rotated arrays, another low-profile antenna of hollow
cylinder is also proposed and the function of reconnaissance with
microstrip antenna on Mini UAV (unmanned aerial vehicle) are
evaluated in practical flight test.
Abstract: This paper presents the experimental results of
comparison between leakage currents and discharge currents. The leakage currents were obtained on polluted porcelain insulator.
Whereas, the discharge currents were obtained on lightly artificial
polluted porcelain specimen. The conducted measurements were
leakage current or discharge current and applied voltage. The insulator or specimen was in a hermetically sealed chamber, and the
current waveforms were analyzed using FFT.
The result indicated that the leakage current (LC) on low RH condition the fifth harmonic would be visible, and followed by the
seventh harmonic. The insulator had capacitive property. Otherwise,
on 99% relative humidity, the fifth harmonic would also be visible,
and the phase angle reached up to 12.2 degree. Whereas, on discharge current, the third harmonic would be visible, and followed
by fifth harmonic. The third harmonic would increase as pressure reduced. On this condition, the specimen had a non-linear characteristics
Abstract: Space Vector Modulation (SVM) is an optimum Pulse Width Modulation (PWM) technique for an inverter used in a variable frequency drive applications. It is computationally rigorous and hence limits the inverter switching frequency. Increase in switching frequency can be achieved using Neural Network (NN) based SVM, implemented on application specific chips. This paper proposes a neural network based SVM technique for a Voltage Source Inverter (VSI). The network proposed is independent of switching frequency. Different architectures are investigated keeping the total number of neurons constant. The performance of the inverter is compared for various switching frequencies for different architectures of NN based SVM. From the results obtained, the network with minimum resource and appropriate word length is identified. The bit precision required for this application is identified. The network with 8-bit precision is implemented in the IC XCV 400 and the results are presented. The performance of NN based general purpose SVM with higher bit precision is discussed.
Abstract: This paper reviews the optimization available
transmission capability (ATC) of power systems using a device of
FACTS named SSSC equipped with energy storage devices. So that,
emplacement and improvement of parameters of SSSC will be
illustrated. Thus, voltage magnitude constraints of network buses,
line transient stability constraints and voltage breakdown constraints
are considered. To help the calculations, a comprehensive program in
DELPHI is provided, which is able to simulate and trace the
parameters of SSSC has been installed on a specific line.
Furthermore, the provided program is able to compute ATC, TTC
and maximum value of their enhancement after using SSSC.
Abstract: The main objective of this paper is a comparative
investigate in enhancement of damping power system oscillation via
coordinated design of the power system stabilizer (PSS) and static
synchronous series compensator (SSSC) and static synchronous
compensator (STATCOM). The design problem of FACTS-based
stabilizers is formulated as a GA based optimization problem. In this
paper eigenvalue analysis method is used on small signal stability of
single machine infinite bus (SMIB) system installed with SSSC and
STATCOM. The generator is equipped with a PSS. The proposed
stabilizers are tested on a weakly connected power system with
different disturbances and loading conditions. This aim is to enhance
both rotor angle and power system stability. The eigenvalue analysis
and non-linear simulation results are presented to show the effects of
these FACTS-based stabilizers and reveal that SSSC exhibits the best
effectiveness on damping power system oscillation.
Abstract: The running logs of a process hold valuable
information about its executed activity behavior and generated activity
logic structure. Theses informative logs can be extracted, analyzed and
utilized to improve the efficiencies of the process's execution and
conduction. One of the techniques used to accomplish the process
improvement is called as process mining. To mine similar processes is
such an improvement mission in process mining. Rather than directly
mining similar processes using a single comparing coefficient or a
complicate fitness function, this paper presents a simplified heuristic
process mining algorithm with two similarity comparisons that are
able to relatively conform the activity logic sequences (traces) of
mining processes with those of a normalized (regularized) one. The
relative process conformance is to find which of the mining processes
match the required activity sequences and relationships, further for
necessary and sufficient applications of the mined processes to process
improvements. One similarity presented is defined by the relationships
in terms of the number of similar activity sequences existing in
different processes; another similarity expresses the degree of the
similar (identical) activity sequences among the conforming processes.
Since these two similarities are with respect to certain typical behavior
(activity sequences) occurred in an entire process, the common
problems, such as the inappropriateness of an absolute comparison and
the incapability of an intrinsic information elicitation, which are often
appeared in other process conforming techniques, can be solved by the
relative process comparison presented in this paper. To demonstrate
the potentiality of the proposed algorithm, a numerical example is
illustrated.
Abstract: Life is beautiful. But, it is decided by genes, environment and the individual and shattered by the natural and / or the invited problems. Most of the global rural helpless masses are struggling for their survival since; they are neglected in all aspects of life including health. Amidst a countless number of miserable diseases in man, diabetes is becoming a dreaded killer and ramifying the entire globe in a jet speed. Diabetes control continues as a Herculean task to the scientific community and the modern society in the 21st century also. T2DM is not pertaining to any age and it can develop even during the childhood. This multifactorial disease abruptly changes the activities of certain vital biomarkers in the present rural T2DM cases. A remarkable variation in the levels of biomarkers like AST, ALT, GGT, ALP, LDH, HbA1C, C- peptide, fasting sugar, post-prandial sugar, sodium, potassium, BUN, creatinine and insulin show the rampant nature of T2DM in this physically active rural agrarian community.
Abstract: The voice signal in Voice over Internet protocol (VoIP) system is processed through the best effort policy based IP network, which leads to the network degradations including delay, packet loss jitter. The work in this paper presents the implementation of finite impulse response (FIR) filter for voice quality improvement in the VoIP system through distributed arithmetic (DA) algorithm. The VoIP simulations are conducted with AMR-NB 6.70 kbps and G.729a speech coders at different packet loss rates and the performance of the enhanced VoIP signal is evaluated using the perceptual evaluation of speech quality (PESQ) measurement for narrowband signal. The results show reduction in the computational complexity in the system and significant improvement in the quality of the VoIP voice signal.
Abstract: All the geophysical phenomena including river
networks and flow time series are fractal events inherently and fractal
patterns can be investigated through their behaviors. A non-linear
system like a river basin can well be analyzed by a non-linear
measure such as the fractal analysis. A bilateral study is held on the
fractal properties of the river network and the river flow time series.
A moving window technique is utilized to scan the fractal properties
of them. Results depict both events follow the same strategy
regarding to the fractal properties. Both the river network and the
time series fractal dimension tend to saturate in a distinct value.
Abstract: Aluminum alloy has an extensive range of industrial application due to its consistent mechanical properties and structural integrity. The heat treatment by precipitation technique affected the Magnesium, Silicon Manganese and copper crystals dissolved in the Aluminum alloy. The crystals dislocated to precipitate on the crystal’s boundaries of the Aluminum alloy when given a thermal energy increased its hardness. In this project various times and temperature were varied to find out the best combination of these variables to increase the precipitation of the metals on the Aluminum crystal’s boundaries which will lead to get the highest hardness. These specimens are then tested for their hardness and tensile strength. It is noticed that when the temperature increases, the precipitation increases and consequently the hardness increases. A threshold temperature value (264C0) of Aluminum alloy should not be reached due to the occurrence of recrystalization which causes the crystal to grow. This recrystalization process affected the ductility of the alloy and decrease hardness. In addition, and while increasing the temperature the alloy’s mechanical properties will decrease. The mechanical properties, namely tensile and hardness properties are investigated according to standard procedures. In this research, different temperature and time have been applied to increase hardening.The highest hardness at 100°c in 6 hours equals to 207.31 HBR, while at the same temperature and time the lowest elongation equals to 146.5.
Abstract: Several wireless networks security standards have been proposed and widely implemented in both business and home environments in order to protect the network from unauthorized access. However, the implementation of such standards is usually achieved by network administrators without even knowing the standards- weaknesses and strengths. The intention of this paper is to evaluate and analyze the impact over the network-s security due to the implementation of the wireless networks security standards WEP, WPA and WLAN 802.1X.
Abstract: This study describes the preparation of a novel proton
conducting membranes based on bacterial cellulose (BC) modified by
grafting of 2-acrylamido-2-methyl-1 -propanesulfonic acid (AMPS)
through UV-induced graft polymerization. These AMPS-g-BC
membranes have been characterized by various techniques including
FTIR, SEM and TGA, to find their successful grafting of AMPS on
BC, surface morphology and thermal stability, respectively. Physical
properties of AMPS-g-BC membranes have been assessed in terms of
Lamda value( λ ), ion exchange capacity(IEC) and proton
conductivity. The relationship between degree of grafting and AMPS
concentration used for grafting has been determined by weight gain
method. An optimum proton conductivity equal to 2.89x10-2 S cm-1
and IEC value equal to 1.79 mmol g-1 have been obtained when 20
wt% AMPS concentration is used for grafting (i.e. the corresponding
membrane is notated as AMPS20-g-BC).
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: Business and IT alignment has continued as a
top concern for business and IT executives for almost three
decades. Many researchers have conducted empirical studies on
the relationship between business-IT alignment and performance.
Yet, these approaches, lacking a social perspective, have had little
impact on sustaining performance and competitive advantage. In
addition to the limited alignment literature that explores
organisational learning that is represented in shared understanding,
communication, cognitive maps and experiences.
Hence, this paper proposes an integrated process that enables
social and intellectual dimensions through the concept of
organisational learning. In particular, the feedback and feedforward
process which provide a value creation across dynamic
multilevel of learning. This mechanism enables on-going
effectiveness through development of individuals, groups and
organisations, which improves the quality of business and IT
strategies and drives to performance.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: The three-dimensional incompressible flow past a
rectangular open cavity is investigated, where the aspect ratio of the
cavity is considered as 4. The principle objective is to use large-eddy
simulation to resolve and control the large-scale structures, which are
largely responsible for flow oscillations in a cavity. The flow past an
open cavity is very common in aerospace applications and can be a
cause of acoustic source due to hydrodynamic instability of the shear
layer and its interactions with the downstream edge. The unsteady
Navier-stokes equations have been solved on a staggered mesh using
a symmetry-preserving central difference scheme. Synthetic jet has
been used as an active control to suppress the cavity oscillations in
wake mode for a Reynolds number of ReD = 3360. The effect of
synthetic jet has been studied by varying the jet amplitude and
frequency, which is placed at the upstream wall of the cavity. The
study indicates that there exits a frequency band, which is larger than
a critical value, is effective in attenuating cavity oscillations when
blowing ratio is more than 1.0.
Abstract: Organization of video databases is becoming difficult
task as the amount of video content increases. Video classification
based on the content of videos can significantly increase the speed of
tasks such as browsing and searching for a particular video in a
database. In this paper, a content-based videos classification system
for the classes indoor and outdoor is presented. The system is
intended to be used on a mobile platform with modest resources. The
algorithm makes use of the temporal redundancy in videos, which
allows using an uncomplicated classification model while still
achieving reasonable accuracy. The training and evaluation was done
on a video database of 443 videos downloaded from a video sharing
service. A total accuracy of 87.36% was achieved.