Abstract: The objective of present work is to stimulate the
machining of material by electrical discharge machining (EDM) to
give effect of input parameters like discharge current (Ip), pulse on
time (Ton), pulse off time (Toff) which can bring about changes in the
output parameter, i.e. material removal rate. Experimental data was
gathered from die sinking EDM process using copper electrode and
Medium Carbon Steel (AISI 1040) as work-piece. The rules of
membership function (MF) and the degree of closeness to the
optimum value of the MMR are within the upper and lower range of
the process parameters. It was found that proposed fuzzy model is in
close agreement with the experimental results. By Intelligent, model
based design and control of EDM process parameters in this study
will help to enable dramatically decreased product and process
development cycle times.
Abstract: The PH curve can be constructed by given parameters, but the shape of the curve is not so easy to image from the value of the parameters. On the contract, Bézier curve can be constructed by the control polygon, and from the control polygon, we can image the figure of the curve. In this paper, we want to use the hodograph of Bézier curve to construct PH curve by selecting part of the control vectors, and produce other control vectors, so the property of PH curve exists.
Abstract: The paper discusses a 3D numerical solution of the inverse boundary problem for a continuous casting process of alloy. The main goal of the analysis presented within the paper was to estimate heat fluxes along the external surface of the ingot. The verified information on these fluxes was crucial for a good design of a mould, effective cooling system and generally the whole caster. In the study an enthalpy-porosity technique implemented in Fluent package was used for modeling the solidification process. In this method, the phase change interface was determined on the basis of the liquid fraction approach. In inverse procedure the sensitivity analysis was applied for retrieving boundary conditions. A comparison of the measured and retrieved values showed a high accuracy of the computations. Additionally, the influence of the accuracy of measurements on the estimated heat fluxes was also investigated.
Abstract: In recent years various types of electric vehicles
has gained again increasing attention as an environmentally
benign technology in transport. Especially for urban areas with
high local pollution this Zero-emission technology (at the point
of use) is considered to provide proper solutions. Yet, the bad
economics and the limited driving ranges are still major barriers
for a broader market penetration of battery electric vehicles
(BEV) and of fuel cell vehicles (FCV). The major result of our
analyses is that the most important precondition for a further
dissemination of BEV in urban areas are emission-free zones.
This is an instrument which allows the promotion of BEV
without providing excessive subsidies. In addition, it is
important to note that the full benefits of EV can only be
harvested if the electricity used is produced from renewable
energy sources. That is to say, it has to be ensured that the use of
BEV in urban areas is clearly linked to a green electricity
purchase model. And moreover, the introduction of a CO2-
emission-based tax system would support this requirement.
Abstract: This paper shows the results of empirical research. It
presents experiences of Polish companies from the Podkarpackie
voivodeship connected with implementing EMS according to the
requirements of the ISO 14001 international standard. The incentives
to introduce and certify organizational eco-innovation, which formal
EMSs are treated as, are presented in this paper.
Abstract: Thermo-chemical treatment (TCT) such as pyrolysis
is getting recognized as a valid route for (i) materials and valuable
products and petrochemicals recovery; (ii) waste recycling; and (iii)
elemental characterization. Pyrolysis is also receiving renewed
attention for its operational, economical and environmental
advantages. In this study, samples of polyethylene terephthalate
(PET) and polystyrene (PS) were pyrolysed in a microthermobalance
reactor (using a thermogravimetric-TGA setup). Both
polymers were prepared and conditioned prior to experimentation.
The main objective was to determine the kinetic parameters of the
depolymerization reactions that occur within the thermal degradation
process. Overall kinetic rate constants (ko) and activation energies
(Eo) were determined using the general kinetics theory (GKT)
method previously used by a number of authors. Fitted correlations
were found and validated using the GKT, errors were within ± 5%.
This study represents a fundamental step to pave the way towards the
development of scaling relationship for the investigation of larger
scale reactors relevant to industry.
Abstract: This paper uses quasi-steady molecular statics model
and diamond tool to carry out simulation temperature rise of nanoscale
orthogonal cutting single-crystal silicon. It further qualitatively
analyzes temperature field of silicon workpiece without considering
heat transfer and considering heat transfer. This paper supposes that
the temperature rise of workpiece is mainly caused by two heat sources:
plastic deformation heat and friction heat. Then, this paper develops a
theoretical model about production of the plastic deformation heat and
friction heat during nanoscale orthogonal cutting. After the increased
temperature produced by these two heat sources are added up, the
acquired total temperature rise at each atom of the workpiece is
substituted in heat transfer finite difference equation to carry out heat
transfer and calculates the temperature field in each step and makes
related analysis.
Abstract: This paper aims to give a full study of the dynamic
behavior of a mono-phase active power filter. First, the principle of
the parallel active power filter will be introduced. Then, a
dimensioning procedure for all its components will be explained in
detail, such as the input filter, the current and voltage controllers.
This active power filter is simulated using OrCAD program showing
the validity of the theoretical study.
Abstract: In this paper, we present a new method for
incorporating global shift invariance in support vector machines.
Unlike other approaches which incorporate a feature extraction stage,
we first scale the image and then classify it by using the modified
support vector machines classifier. Shift invariance is achieved by
replacing dot products between patterns used by the SVM classifier
with the maximum cross-correlation value between them. Unlike the
normal approach, in which the patterns are treated as vectors, in our
approach the patterns are treated as matrices (or images). Crosscorrelation
is computed by using computationally efficient
techniques such as the fast Fourier transform. The method has been
tested on the ORL face database. The tests indicate that this method
can improve the recognition rate of an SVM classifier.
Abstract: To realize the vision of ubiquitous computing, it is
important to develop a context-aware infrastructure which can help
ubiquitous agents, services, and devices become aware of their
contexts because such computational entities need to adapt themselves
to changing situations. A context-aware infrastructure manages the
context model representing contextual information and provides
appropriate information. In this paper, we introduce Context-Aware
Middleware for URC System (hereafter CAMUS) as a context-aware
infrastructure for a network-based intelligent robot system and discuss
the ontology-based context modeling and reasoning approach which is
used in that infrastructure.
Abstract: The automatic discrimination of seismic signals is an important practical goal for the earth-science observatories due to the large amount of information that they receive continuously. An essential discrimination task is to allocate the incoming signal to a group associated with the kind of physical phenomena producing it. In this paper, we present new techniques for seismic signals classification: local, regional and global discrimination. These techniques were tested on seismic signals from the data base of the National Geophysical Institute of the Centre National pour la Recherche Scientifique et Technique (Morocco) by using the Moroccan software for seismic signals analysis.
Abstract: This paper introduces application of multi degree of freedom fuzzy(MDOFF) controller in permanent magnet (PM)drive system. The drive system model is developed for FO control. Simulation of the system is carried out to predict the performance at NL and under load,. The results indicate that application of MDOFF controller is effective for sensorless PM drive system.
Abstract: This paper describes the challenges on the requirements engineering for developing an enterprise applications in higher
education environment. The development activities include software implementation, maintenance, and enhancement and support for online
transaction processing and overnight batch processing.
Generally, an enterprise application for higher education environment
may include Student Information System (SIS), HR/Payroll system,
Financial Systems etc. By the way, there are so many challenges in
requirement engineering phases in order to provide two distinctive
services that are production processing support and systems
development.
Abstract: Since large power transformers are the most
expensive and strategically important components of any power
generator and transmission system, their reliability is crucially
important for the energy system operation. Also, Circuit breakers are
very important elements in the power transmission line so monitoring
the events gives a knowledgebase to determine time to the next
maintenance. This paper deals with the introduction of the
comparative method of the state estimation of transformers and
Circuit breakers using continuous monitoring of voltage, current.
This paper gives details a new method based on wavelet to apparatus
insulation monitoring. In this paper to insulation monitoring of
transformer, a new method based on wavelet transformation and
neutral point analysis is proposed. Using the EMTP tools, fault in
transformer winding and the detailed transformer winding model
were simulated. The current of neutral point of winding was analyzed
by wavelet transformation. It is shown that the neutral current of the
transformer winding has useful information about fault in insulation
of the transformer.
Abstract: A novel concept to balance and tradeoff between
make-to-stock and make-to-order has been hybrid MTS/MTO production context. One of the most important decisions involved in
the hybrid MTS/MTO environment is determining whether a product
is manufactured to stock, to order, or hybrid MTS/MTO strategy. In this paper, a model based on analytic network process is developed to tackle the addressed decision. Since the regarded decision deals with
the uncertainty and ambiguity of data as well as experts- and
managers- linguistic judgments, the proposed model is equipped with
fuzzy sets theory. An important attribute of the model is its generality due to diverse decision factors which are elicited from the
literature and developed by the authors. Finally, the model is validated by applying to a real case study to reveal how the proposed
model can actually be implemented.
Abstract: A spanning tree of a connected graph is a tree which
consists the set of vertices and some or perhaps all of the edges from
the connected graph. In this paper, a model for spanning tree
transformation of connected graphs into single-row networks, namely
Spanning Tree of Connected Graph Modeling (STCGM) will be
introduced. Path-Growing Tree-Forming algorithm applied with
Vertex-Prioritized is contained in the model to produce the spanning
tree from the connected graph. Paths are produced by Path-Growing
and they are combined into a spanning tree by Tree-Forming. The
spanning tree that is produced from the connected graph is then
transformed into single-row network using Tree Sequence Modeling
(TSM). Finally, the single-row routing problem is solved using a
method called Enhanced Simulated Annealing for Single-Row
Routing (ESSR).
Abstract: Heavy rainfall greatly affects the aerodynamic performance of the aircraft. There are many accidents of aircraft caused by aerodynamic efficiency degradation by heavy rain.
In this Paper we have studied the heavy rain effects on the aerodynamic efficiency of cambered NACA 64-210 and symmetric
NACA 0012 airfoils. Our results show significant increase in drag and decrease in lift. We used preprocessing software gridgen for creation of geometry and mesh, used fluent as solver and techplot as postprocessor. Discrete phase modeling called DPM is used to model the rain particles using two phase flow approach. The rain particles are assumed to be inert.
Both airfoils showed significant decrease in lift and increase in drag in simulated rain environment. The most significant difference between these two airfoils was the NACA 64-210 more sensitivity than NACA 0012 to liquid water content (LWC). We believe that the results showed in this paper will be useful for the designer of the commercial aircrafts and UAVs, and will be helpful for training of the pilots to control the airplanes in heavy rain.
Abstract: Nano MgO has been synthesized by hydration and
dehydration method by modifies the commercial MgO. The prepared
MgO had been investigated as a heterogeneous base catalyst for
transesterification process for biodiesel production using palm oil.
TGA, FT-IR and XRD results obtained from this study lie each other
and proved in the formation of nano MgO from decomposition of
Mg(OH)2. This study proved that the prepared nano MgO was a
better base transesterification catalyst compared to commercial MgO.
The nano MgO calcined at 600ºC had gives the highest conversion of
51.3% of palm oil to biodiesel.
Abstract: In a state-of-the-art industrial production line of
photovoltaic products the handling and automation processes are of
particular importance and implication. While processing a fully
functional crystalline solar cell an as-cut photovoltaic wafer is subject
to numerous repeated handling steps. With respect to stronger
requirements in productivity and decreasing rejections due to defects
the mechanical stress on the thin wafers has to be reduced to a
minimum as the fragility increases by decreasing wafer thicknesses.
In relation to the increasing wafer fragility, researches at the
Fraunhofer Institutes IPA and CSP showed a negative correlation
between multiple handling processes and the wafer integrity. Recent
work therefore focused on the analysis and optimization of the dry
wafer stack separation process with compressed air. The achievement
of a wafer sensitive process capability and a high production
throughput rate is the basic motivation in this research.
Abstract: Methanol-to-olefins (MTO) coupled with
transformation of coal or natural gas to methanol gives an interesting
and promising way to produce ethylene and propylene. To investigate
solid concentration in gas-solid fluidized bed for methanol-to-olefins
process catalyzed by SAPO-34, a cold model experiment system is
established in this paper. The system comprises a gas distributor in a
300mm internal diameter and 5000mm height acrylic column, the
fiber optic probe system and series of cyclones. The experiments are
carried out at ambient conditions and under different superficial gas
velocity ranging from 0.3930m/s to 0.7860m/s and different initial bed
height ranging from 600mm to 1200mm. The effects of radial
distance, axial distance, superficial gas velocity, initial bed height on
solid concentration in the bed are discussed. The effects of distributor
shape and porosity on solid concentration are also discussed. The
time-averaged solid concentration profiles under different conditions
are obtained.