Abstract: The unsteady wake of an EPPLER 361 airfoil in
pitching motion has been investigated in a subsonic wind tunnel by
hot-wire anemometry. The airfoil was given the pitching motion
about the one-quarter chord axis at reduced frequency of 0182.
Streamwise mean velocity profiles (wake profiles) were investigated
at several vertically aligned points behind the airfoil at one-quarter
chord downstream distance from trailing edge. Oscillation amplitude
and mean angle of attack were varied to determine the effects on
wake profiles. When the maximum dynamic angle of attack was
below the static stall angle of attack, weak effects on wake were
found by increasing oscillation amplitude and mean angle of attack.
But, for higher angles of attack strong unsteady effects were
appeared on the wake.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: In this paper, we analyze the problem of quasiballistic electron transport in ultra small of mercury -cadmiumtelluride (Hg0.8Cd0.2Te -MCT) n+-n- n+ devices from hydrodynamic point view. From our study, we note that, when the size of the active layer is low than 0.1μm and for low bias application( ( ≥ 9mV), the quasi-ballistic transport has an important effect.
Abstract: Texture classification is a trendy and a catchy
technology in the field of texture analysis. Textures, the repeated
patterns, have different frequency components along different
orientations. Our work is based on Texture Classification and its
applications. It finds its applications in various fields like Medical
Image Classification, Computer Vision, Remote Sensing,
Agricultural Field, and Textile Industry. Weed control has a major
effect on agriculture. A large amount of herbicide has been used for
controlling weeds in agriculture fields, lawns, golf courses, sport
fields, etc. Random spraying of herbicides does not meet the exact
requirement of the field. Certain areas in field have more weed
patches than estimated. So, we need a visual system that can
discriminate weeds from the field image which will reduce or even
eliminate the amount of herbicide used. This would allow farmers to
not use any herbicides or only apply them where they are needed. A
machine vision precision automated weed control system could
reduce the usage of chemicals in crop fields. In this paper, an
intelligent system for automatic weeding strategy Multi Resolution
Combined Statistical & spatial Frequency is used to discriminate the
weeds from the crops and to classify them as narrow, little and broad
weeds.
Abstract: Computer animation is a widely adopted technique used to specify the movement of various objects on screen. The key issue of this technique is the specification of motion. Motion Control Methods are such methods which are used to specify the actions of objects. This paper discusses the various types of motion control methods with special focus on behavioral animation. A behavioral model is also proposed which takes into account the emotions and perceptions of an actor which in turn generate its behavior. This model makes use of an expert system to generate tasks for the actors which specify the actions to be performed in the virtual environment.
Abstract: The fluorescent pseudomonad strain R81 is a root
colonizing rhizobacteria which promotes the growth of many plants
by various mechanisms. Its broth containing siderophore (ironchelating
compound) and 2,4- diacetyl phloroglucinol (DAPG) is
used for preparing bioinoculant formulations for agronomical
applications. Glycerol was found to be the best carbon source for
improved biomass production. Splitting of nitrogen source to NH4Cl
and urea had a stabilizing effect on pH during batch cultivation. Ltryptophan
at 0.5 % in the medium increased the siderophore
production to 850 mg/l. During batch cultivation of the strain in a
bioreactor, a maximum of 4 g/l of dry cell mass, 1.8 g/l of
siderophore and 20 mg/l of DAPG was achieved when glycerol was
15 g/l and C/N ratio was maintained at 12.5. In case of intermittent
feeding of fresh medium during fed-batch cultivation, the dry cell
mass was increased to 25 g/l with improved production of DAPG to
70 mg/l.
Abstract: This paper presents a new high speed simulation methodology to solve the long simulation time problem of CMOS image sensor matrix. Generally, for integrating the pixel matrix in SOC and simulating the system performance, designers try to model the pixel in various modeling languages such as VHDL-AMS, SystemC or Matlab. We introduce a new alternative method based on spice model in cadence design platform to achieve accuracy and reduce simulation time. The simulation results indicate that the pixel output voltage maximum error is at 0.7812% and time consumption reduces from 2.2 days to 13 minutes achieving about 240X speed-up for the 256x256 pixel matrix.
Abstract: Dengue fever has become a major concern for health
authorities all over the world particularly in the tropical countries.
These countries, in particular are experiencing the most worrying
outbreak of dengue fever (DF) and dengue haemorrhagic fever
(DHF). The DF and DHF epidemics, thus, have become the main
causes of hospital admissions and deaths in Malaysia. This paper,
therefore, attempts to examine the environmental factors that may
influence the recent dengue outbreak. The aim of this study is twofold,
firstly is to establish a statistical model to describe the
relationship between the number of dengue cases and a range of
explanatory variables and secondly, to identify the lag operator for
explanatory variables which affect the dengue incidence the most.
The explanatory variables involved include the level of cloud cover,
percentage of relative humidity, amount of rainfall, maximum
temperature, minimum temperature and wind speed. The Poisson and
Negative Binomial regression analyses were used in this study. The
results of the analyses on the 915 observations (daily data taken from
July 2006 to Dec 2008), reveal that the climatic factors comprising of
daily temperature and wind speed were found to significantly
influence the incidence of dengue fever after 2 and 3 weeks of their
occurrences. The effect of humidity, on the other hand, appears to be
significant only after 2 weeks.
Abstract: Technical laboratories are typically considered as
highly hazardous places in the polytechnic institution when
addressing the problems of high incidences and fatality rates. In
conjunction with several topics covered in the technical curricular,
safety and health precaution should be highlighted in order to
connect to few key ideas of being safe. Therefore the assessment of
safety awareness in terms of safety and health about hazardous and
risks at laboratories is needed and has to be incorporated with
technical education and other training programmes. The purpose of
this study was to determine the efficacy of technical laboratory safety
in one of the polytechnics in northern region. The study examined
three related issues that were; the availability of safety material and
equipment, safety practice adopted by technical teachers and
administrator-s safety attitudes in enforcing safety to the students. A
model of efficacy technical laboratory was developed to test the
linear relationship between existing safety material and equipment,
teachers- safety practice and administrators- attitude in enforcing
safety and to identify which of technical laboratory safety issues was
the most pertinent factor to realize safety in technical laboratory.
This was done by analyzing survey-based data sets particularly those
obtained from samples of 210 students in the polytechnic. The
Pearson Correlation was used to measure the association between the
variables and to test the research hypotheses. The result of the study
has found that there was a significant correlation between existing
safety material and equipment, safety practice adopted by teacher
and administrator-s attitude. There was also a significant relationship
between technical laboratory safety and safety practice adopted by
teacher and between technical laboratory safety and administrator
attitude. Hence, safety practice adopted by teacher and administrator
attitude is vital in realizing technical laboratory safety.
Abstract: Space Vector Modulation (SVM) is an optimum Pulse Width Modulation (PWM) technique for an inverter used in a variable frequency drive applications. It is computationally rigorous and hence limits the inverter switching frequency. Increase in switching frequency can be achieved using Neural Network (NN) based SVM, implemented on application specific chips. This paper proposes a neural network based SVM technique for a Voltage Source Inverter (VSI). The network proposed is independent of switching frequency. Different architectures are investigated keeping the total number of neurons constant. The performance of the inverter is compared for various switching frequencies for different architectures of NN based SVM. From the results obtained, the network with minimum resource and appropriate word length is identified. The bit precision required for this application is identified. The network with 8-bit precision is implemented in the IC XCV 400 and the results are presented. The performance of NN based general purpose SVM with higher bit precision is discussed.
Abstract: In this paper, many techniques for blind identification of moving average (MA) process are presented. These methods utilize third- and fourth-order cumulants of the noisy observations of the system output. The system is driven by an independent and identically distributed (i.i.d) non-Gaussian sequence that is not observed. Two nonlinear optimization algorithms, namely the Gradient Descent and the Gauss-Newton algorithms are exposed. An algorithm based on the joint-diagonalization of the fourth-order cumulant matrices (FOSI) is also considered, as well as an improved version of the classical C(q, 0, k) algorithm based on the choice of the Best 1-D Slice of fourth-order cumulants. To illustrate the effectiveness of our methods, various simulation examples are presented.
Abstract: We developed a GPS-based navigation device for the
blind, with audio guidance in Thai language. The device is composed
of simple and inexpensive hardware components. Its user interface is
quite simple. It determines optimal routes to various landmarks in our
university campus by using heuristic search for the next waypoints.
We tested the device and made note of its limitations and possible
extensions.
Abstract: This paper addresses integration issues in supply
chain, and tries to investigate how different aspects of integration are
linked with some product features. Integration in this study is
interpreted as "internal", "upstream" (supply), and "downstream"
(demand). Two features of product innovative and quality are
considered. To examine the relationships between supply chain
integrations – as mentioned above, and product features, this research
follows the survey method in automotive industry.The results imply
that supply chain upstream integration has a higher impact on product
quality, comparing to internal and supply chain downstream
integrations. It is also found that the influence of supply chain
downstream integration on product innovation is greater than other
variables. In brief, this study mainly tackles the importance of
specific level of supply chain integrations and its effects on two
product features.
Abstract: This study assessed the effects of climate change on
Thai soybeans under simulation situations. Our study is focused on
temperature variability and effects on growth, yield, and genetic
changes in 2 generations of Chiang Mai 60 cultivars. In the
experiment, soybeans were exposed to 3 levels of air temperature for
8 h day-1 in an open top chamber for 2 cropping periods. Air
temperature levels in each treatment were controlled at 30-33°C (±
2.3) for LT-treatment, 33-36°C ( ± 2.4) for AT-treatment, and 36-40
°C ( ± 3.2) for HT-treatment, respectively. Positive effects of high
temperature became obvious at the maturing stage when yield
significantly increased in both cropping periods. Results in growth
indicated that shoot length at the pre-maturing stage
(V3-R3) was more positively affected by high temperature than at the
maturing stage. However, the positive effect on growth under high
temperature was not found in the 2nd cropping period. Finally, genetic
changes were examined in phenotype characteristics by the AFLPs
technique. The results showed that the high temperature factor clearly
caused genetic change in the soybeans and showed more alteration in
the 2nd cropping period.
Abstract: The paper describes the workings for four models of
CONWIP systems used till date; the basic CONWIP system, the
hybrid CONWIP system, the multi-product CONWIP system, and the
parallel CONWIP system. The final novel model is introduced in this
paper in a general form. These models may be adopted for analysis
for both simulation studies and implementation on the shop floor. For
each model, input parameters of interest are highlighted and their
impacts on several system performance measures are addressed.
Abstract: Life is beautiful. But, it is decided by genes, environment and the individual and shattered by the natural and / or the invited problems. Most of the global rural helpless masses are struggling for their survival since; they are neglected in all aspects of life including health. Amidst a countless number of miserable diseases in man, diabetes is becoming a dreaded killer and ramifying the entire globe in a jet speed. Diabetes control continues as a Herculean task to the scientific community and the modern society in the 21st century also. T2DM is not pertaining to any age and it can develop even during the childhood. This multifactorial disease abruptly changes the activities of certain vital biomarkers in the present rural T2DM cases. A remarkable variation in the levels of biomarkers like AST, ALT, GGT, ALP, LDH, HbA1C, C- peptide, fasting sugar, post-prandial sugar, sodium, potassium, BUN, creatinine and insulin show the rampant nature of T2DM in this physically active rural agrarian community.
Abstract: Mobile Ad Hoc network is an infrastructure less
network which operates with the coordination of each node. Each node
believes to help another node, by forwarding its data to/from another
node. Unlike a wired network, nodes in an ad hoc network are resource
(i.e. battery, bandwidth computational capability and so on)
constrained. Such dependability of one node to another and limited
resources of nodes can result in non cooperation by any node to
accumulate its resources. Such non cooperation is known as selfish
behavior.
This paper discusses the performance analysis of very well known
MANET single-path (i.e. AODV) and multi-path (i.e. AOMDV)
routing protocol, in the presence of selfish behaviors. Along with
existing selfish behaviors, a new variation is also studied. Extensive
simulations were carried out using ns-2 and the study concluded that
the multi-path protocol (i.e. AOMDV) with link disjoint configuration
outperforms the other two configurations.
Abstract: Aluminum alloy has an extensive range of industrial application due to its consistent mechanical properties and structural integrity. The heat treatment by precipitation technique affected the Magnesium, Silicon Manganese and copper crystals dissolved in the Aluminum alloy. The crystals dislocated to precipitate on the crystal’s boundaries of the Aluminum alloy when given a thermal energy increased its hardness. In this project various times and temperature were varied to find out the best combination of these variables to increase the precipitation of the metals on the Aluminum crystal’s boundaries which will lead to get the highest hardness. These specimens are then tested for their hardness and tensile strength. It is noticed that when the temperature increases, the precipitation increases and consequently the hardness increases. A threshold temperature value (264C0) of Aluminum alloy should not be reached due to the occurrence of recrystalization which causes the crystal to grow. This recrystalization process affected the ductility of the alloy and decrease hardness. In addition, and while increasing the temperature the alloy’s mechanical properties will decrease. The mechanical properties, namely tensile and hardness properties are investigated according to standard procedures. In this research, different temperature and time have been applied to increase hardening.The highest hardness at 100°c in 6 hours equals to 207.31 HBR, while at the same temperature and time the lowest elongation equals to 146.5.
Abstract: If an unsteady heat transfer or heat impulse happens in
part of the cryogenic pipeline system of large space environment
simulation equipment while running in vacuum environment, it will
lead to abnormal flow of the cryogenic fluid in the pipeline. When the
situation gets worse, the cryogenic fluid in the pipeline will have phase
change and a gas block which results in the malfunction of the
cryogenic pipeline system. Referring to the structural parameter of a
typical cryogenic pipeline system and the basic equation, an analytical
model and a calculation model for cryogenic pipeline system can be
built. The various factors which influence the thermal resistance of a
cryogenic pipeline system can be analyzed and calculated by using the
qualitative analysis relation deduced for thermal resistance of pipeline.
The research conclusion could provide theoretical support for the
design and operation of a cryogenic pipeline system