Abstract: The purpose of this article is to study the effects of
plants cover on overland flow and, therefore, its influences on the
amount of eroded and transported soil. In this investigation, all the
experiments were conducted in the LEGHYD laboratory using a
rainfall simulator and a soil tray. The experiments were conducted
using an experimental plot (soil tray) which is 2m long, 0.5 m wide
and 0.15 m deep. The soil used is an agricultural sandy soil (62,08%
coarse sand, 19,14% fine sand, 11,57% silt and 7,21% clay). Plastic
rods (4 mm in diameter) were used to simulate the plants at different
densities: 0 stem/m2 (bared soil), 126 stems/m², 203 stems/m², 461
stems/m² and 2500 stems/m²). The used rainfall intensity is 73mm/h
and the soil tray slope is fixed to 3°. The results have shown that the
overland flow velocities decreased with increasing stems density, and
the density cover has a great effect on sediment concentration.
Darcy–Weisbach and Manning friction coefficients of overland flow
increased when the stems density increased. Froude and Reynolds
numbers decreased with increasing stems density and, consequently,
the flow regime of all treatments was laminar and subcritical. From
these findings, we conclude that increasing the plants cover can
efficiently reduce soil loss and avoid denuding the roots plants.
Abstract: The hydrodynamics behavior of fluid flow in microconverging
plates is investigated analytically. Effects of Knudsen number () on the microchannel hydrodynamics behavior and the
coefficient of friction are investigated. It is found that as increases the slip in the hydrodynamic boundary condition increases.
Also, the coefficient of friction decreases as increases.
Abstract: In this article the investigation about installation heat
recovery steam generation (HRSG) on the exhaust of turbo generators of phases 2&3 at South Pars Gas Complex is presented.
The temperature of exhaust gas is approximately 665 degree centigrade, Installation of heat recovery boiler was simulated in
ThermoFlow 17.0.2 software, based on test operation data and the
equipments site operation conditions in Pars exclusive economical energy area, the affect of installation HRSG package on the available
gas turbine and its operation parameters, ambient temperature, the
exhaust temperatures steam flow rate were investigated. Base on the results recommended HRSG package should have the capacity for 98
ton per hour high pressure steam generation this refinery, by use of
exhaust of three gas turbines for each package in operation condition of each refinery at 30 degree centigrade. Besides saving energy this
project will be an Environment-Friendly project. The Payback Period
is estimated approximately 1.8 year, with considering Clean Development Mechanism.
Abstract: The emerging Semantic Web has been attracted many
researchers and developers. New applications have been developed on top of Semantic Web and many supporting tools introduced to improve its software development process. Metadata modeling is one of development process where supporting tools exists. The existing
tools are lack of readability and easiness for a domain knowledge expert to graphically models a problem in semantic model. In this paper, a metadata modeling tool called RDFGraph is proposed. This
tool is meant to solve those problems. RDFGraph is also designed to work with modern database management systems that support RDF and to improve the performance of the query execution process. The
testing result shows that the rules used in RDFGraph follows the W3C standard and the graphical model produced in this tool is properly translated and correct.
Abstract: Although White LED lighting systems powered by solar cells have presented for many years, they are not widely used in today application because of their cost and low energy conversion efficiency. The proposed system use the dc power generated by fixed solar cells module to energize White LED light sources that are operated by directly connected White LED with current limitation resistors, resulting in much more power consumption. This paper presents the use of white LED as a general lighting application powered by tracking solar cells module and using pulse to apply the electrical power to the White LED. These systems resulted in high efficiency power conversion, low power consumption, and long light of the white LED.
Abstract: In this paper an ant colony optimization algorithm is
developed to solve the permutation flow shop scheduling problem. In
the permutation flow shop scheduling problem which has been vastly
studied in the literature, there are a set of m machines and a set of n
jobs. All the jobs are processed on all the machines and the sequence
of jobs being processed is the same on all the machines. Here this
problem is optimized considering two criteria, makespan and total
flow time. Then the results are compared with the ones obtained by
previously developed algorithms. Finally it is visible that our
proposed approach performs best among all other algorithms in the
literature.
Abstract: The world of wireless telecommunications is rapidly evolving. Technologies under research and development promise to deliver more services to more users in less time. This paper presents the emerging technologies helping wireless systems grow from where we are today into our visions of the future. This paper will cover the applications and characteristics of emerging wireless technologies: Wireless Local Area Networks (WiFi-802.11n), Wireless Personal Area Networks (ZigBee) and Wireless Metropolitan Area Networks (WiMAX). The purpose of this paper is to explain the impending 802.11n standard and how it will enable WLANs to support emerging media-rich applications. The paper will also detail how 802.11n compares with existing WLAN standards and offer strategies for users considering higher-bandwidth alternatives. The emerging IEEE 802.15.4 (ZigBee) standard aims to provide low data rate wireless communications with high-precision ranging and localization, by employing UWB technologies for a low-power and low cost solution. WiMAX (Worldwide Interoperability for Microwave Access) is a standard for wireless data transmission covering a range similar to cellular phone towers. With high performance in both distance and throughput, WiMAX technology could be a boon to current Internet providers seeking to become the leader of next generation wireless Internet access. This paper also explores how these emerging technologies differ from one another.
Abstract: This work deals with aspects of support vector machine learning for large-scale data mining tasks. Based on a decomposition algorithm for support vector machine training that can be run in serial as well as shared memory parallel mode we introduce a transformation of the training data that allows for the usage of an expensive generalized kernel without additional costs. We present experiments for the Gaussian kernel, but usage of other kernel functions is possible, too. In order to further speed up the decomposition algorithm we analyze the critical problem of working set selection for large training data sets. In addition, we analyze the influence of the working set sizes onto the scalability of the parallel decomposition scheme. Our tests and conclusions led to several modifications of the algorithm and the improvement of overall support vector machine learning performance. Our method allows for using extensive parameter search methods to optimize classification accuracy.
Abstract: This paper presents a systematic approach for designing Unified Power Flow Controller (UPFC) based supplementary damping controllers for damping low frequency oscillations in a single-machine infinite-bus power system. Detailed investigations have been carried out considering the four alternatives UPFC based damping controller namely modulating index of series inverter (mB), modulating index of shunt inverter (mE), phase angle of series inverter (δB ) and phase angle of the shunt inverter (δE ). The design problem of the proposed controllers is formulated as an optimization problem and Real- Coded Genetic Algorithm (RCGA) is employed to optimize damping controller parameters. Simulation results are presented and compared with a conventional method of tuning the damping controller parameters to show the effectiveness and robustness of the proposed design approach.
Abstract: Magetan area is going to be the object of this research
which is located in East Java, Indonesia. The data were obtained
from 270 civil servants working at the Magetan District government.
The data were analyzed using the Structural Equation Modeling with
Partial Least Square program. The research showed the following
findings: (1) job motivation variable has a positive and significant
effect on organizational citizenship behavior (OCB); (2) work
environment has positive and significant effect on OCB; (3)
leadership variable has positive and significant effect on OCB; (4)
job motivation variable has no significant effect on job satisfaction;
(5) work environment variable has no significant effect on job
satisfaction; (6) leadership variable has no significant effect on job
satisfaction; (7) OCB is positively and significantly associated with
job satisfaction; (8) job satisfaction variable is positively and
significantly correlated with quality of public service at the Magetan
District government.
Abstract: In this paper we propose new method for
simultaneous generating multiple quantiles corresponding to given
probability levels from data streams and massive data sets. This
method provides a basis for development of single-pass low-storage
quantile estimation algorithms, which differ in complexity, storage
requirement and accuracy. We demonstrate that such algorithms may
perform well even for heavy-tailed data.
Abstract: The electrochemical coagulation of a kaolin
suspension was investigated at the currents of 0.06, 0.12, 0.22, 0.44,
0.85 A (corresponding to 0.68, 1.36, 2.50, 5.00, 9.66 mA·cm-2,
respectively) for the contact time of 5, 10, 20, 30, and 50 min. The
TSS removal efficiency at currents of 0.06 A, 0.12 A and 0.22 A
increased with the amount of iron generated by the sacrificial anode,
while the removal efficiencies did not increase proportionally with
the amount of iron generated at the currents of 0.44 and 0.85 A,
where electroflotation was clearly observed. Zeta potential
measurement illustrated the presence of the highly positive charged
particles created by sorption of highly charged polymeric metal
hydroxyl species onto the negative surface charged kaolin particles at
both low and high applied currents. The disappearance of the
individual peaks after certain contact times indicated the attraction
between these positive and negative charged particles causing
agglomeration. It was concluded that charge neutralization of the
individual species was not the only mechanism operating in the
electrocoagulation process at any current level, but electrostatic
attraction was likely to co-operate or mainly operate.
Abstract: The development of Artificial Neural Networks
(ANNs) is usually a slow process in which the human expert has to
test several architectures until he finds the one that achieves best
results to solve a certain problem. This work presents a new
technique that uses Genetic Programming (GP) for automatically
generating ANNs. To do this, the GP algorithm had to be changed in
order to work with graph structures, so ANNs can be developed. This
technique also allows the obtaining of simplified networks that solve
the problem with a small group of neurons. In order to measure the
performance of the system and to compare the results with other
ANN development methods by means of Evolutionary Computation
(EC) techniques, several tests were performed with problems based
on some of the most used test databases. The results of those
comparisons show that the system achieves good results comparable
with the already existing techniques and, in most of the cases, they
worked better than those techniques.
Abstract: Arc welding is an important joining process widely used in many industrial applications including production of automobile, ships structures and metal tanks. In welding process, the moving electrode causes highly non-uniform temperature distribution that leads to residual stresses and different deviations, especially buckling distortions in thin plates. In order to control the deviations and increase the quality of welded plates, a fixture can be used as a practical and low cost method with high efficiency. In this study, a coupled thermo-mechanical finite element model is coded in the software ANSYS to simulate the behavior of thin plates located by a 3-2-1 positioning system during the welding process. Computational results are compared with recent similar works to validate the finite element models. The agreement between the result of proposed model and other reported data proves that finite element modeling can accurately predict the behavior of welded thin plates.
Abstract: This paper proposes a novel methodology for enabling
debugging and tracing of production web applications without
affecting its normal flow and functionality. This method of debugging
enables developers and maintenance engineers to replace a set of
existing resources such as images, server side scripts, cascading
style sheets with another set of resources per web session. The new
resources will only be active in the debug session and other sessions
will not be affected. This methodology will help developers in tracing
defects, especially those that appear only in production environments
and in exploring the behaviour of the system. A realization of the
proposed methodology has been implemented in Java.
Abstract: In this paper an algorithm for fast wavelength calibration of Optical Spectrum Analyzers (OSAs) using low power reference gas spectra is proposed. In existing OSAs a reference spectrum with low noise for precise detection of the reference extreme values is needed. To generate this spectrum costly hardware with high optical power is necessary. With this new wavelength calibration algorithm it is possible to use a noisy reference spectrum and therefore hardware costs can be cut. With this algorithm the reference spectrum is filtered and the key information is extracted by segmenting and finding the local minima and maxima. Afterwards slope and offset of a linear correction function for best matching the measured and theoretical spectra are found by correlating the measured with the stored minima. With this algorithm a reliable wavelength referencing of an OSA can be implemented on a microcontroller with a calculation time of less than one second.
Abstract: This paper presents a procedure for modeling and tuning the parameters of Thyristor Controlled Series Compensation (TCSC) controller in a multi-machine power system to improve transient stability. First a simple transfer function model of TCSC controller for stability improvement is developed and the parameters of the proposed controller are optimally tuned. Genetic algorithm (GA) is employed for the optimization of the parameter-constrained nonlinear optimization problem implemented in a simulation environment. By minimizing an objective function in which the oscillatory rotor angle deviations of the generators are involved, transient stability performance of the system is improved. The proposed TCSC controller is tested on a multi-machine system and the simulation results are presented. The nonlinear simulation results validate the effectiveness of proposed approach for transient stability improvement in a multimachine power system installed with a TCSC. The simulation results also show that the proposed TCSC controller is also effective in damping low frequency oscillations.
Abstract: Customarily, the LMTD correction factor, FT, is used
to screen alternative designs for a heat exchanger. Designs with
unacceptably low FT values are discarded. In this paper, authors have
proposed a more fundamental criterion, based on feasibility of a
multipass exchanger as the only criteria, followed by economic
optimization. This criterion, coupled with asymptotic energy targets,
provide the complete optimization space in a heat exchanger network
(HEN), where cost-optimization of HEN can be performed with only
Heat Recovery Approach temperature (HRAT) and number-of-shells
as variables.
Abstract: The common practice of operating S-rotor is in an
open environment; however there are times when the rotor is
installed in a bounded environment and there might be changes in the
performance of the rotor. This paper presents the changes in the
performance of S-rotor when operated in bounded flows. The
investigation was conducted experimentally to compare the
performance of the rotors in bounded environment against open
environment. Three different rotors models were designed, fabricated
and subjected to experimental measurements. All of the three models
were having 600 mm height and 300 mm Diameter. They were tested
in three different flow environments; namely: partially bounded
environment, fully bounded environment and open environment.
Rotors were found to have better starting up capabilities when
operated in bounded environment. Apart from that, all rotors manage
to achieve higher Power and Torque Coefficients at a higher Tip
Speed Ratio as compared to the open environment.
Abstract: The lack of security obstructs a large scale de- ployment of the multicast communication model. There- fore, a host of research works have been achieved in order to deal with several issues relating to securing the multicast, such as confidentiality, authentication, non-repudiation, in- tegrity and access control. Many applications require au- thenticating the source of the received traffic, such as broadcasting stock quotes and videoconferencing and hence source authentication is a required component in the whole multicast security architecture. In this paper, we propose a new and efficient source au- thentication protocol which guarantees non-repudiation for multicast flows, and tolerates packet loss. We have simu- lated our protocol using NS-2, and the simulation results show that the protocol allows to achieve improvements over protocols fitting into the same category.