Abstract: The aim of this paper is to compare the effectiveness and electrochemical behavior of typical oilfield corrosion inhibitors with previous oilfield corrosion inhibitors under the same electrochemical techniques to control preferential weld corrosion of X65 pipeline steel in artificial seawater saturated with carbon dioxide at a pressure of one bar. A secondary aim is to investigate the conditions under which current reversal takes place. A flow channel apparatus was used in the laboratory to simulate the actual condition that occurs in marine pipelines. Different samples from the parent metal, the weld metal and the heat affected zone in the pipeline steel were galvanically coupled. The galvanic currents flowing between the weld regions were recorded using zero-resistance ammeters and tested under static and flowing conditions in both inhibited and uninhibited media. The results show that a current reversal took place when 30ppm of both green oilfield inhibitors were present, resulting in accelerated weld corrosion.
Abstract: The main objective of this research is to synthesize silk fibroin fiber for indoor air particulate removal. Silk cocoons were de-gummed using 0.5 wt % Na2CO3 alkaline solutions at 90 Ó╣ìC for 60 mins, washed with distilled water, and dried at 80 Ó╣ìC for 3 hrs in a vacuum oven. Two sets of experiment were conducted to investigate the impacts of initial particulate matter (PM) concentration and that of air flow rate on the removal efficiency. Rice bran collected from a local rice mill in Ubonratchathani province was used as indoor air contaminant in this work. The morphology and physical properties of silk fibroin (SF) fiber were measured. The SEM revealed the deposition of PM on the used fiber. The PM removal efficiencies of 72.29 ± 3.03 % and 39.33 ± 1.99 % were obtained of PM10 and PM2.5, respectively, when using the initial PM concentration at 0.040 mg/m3 and 0.020 mg/m3 of PM10 and PM2.5, respectively, with the air flow rate of 5 L/min.
Abstract: The acid rain causes change in pH level of soil it is
directly influence on root and leaf growth. Yield of the crop was
reduced if acidity of soil is more. Acid rain seeps into the earth and
poisons plants and trees by dissolving toxic substances in the soil,
such as aluminum, which get absorbed by the roots. In present
investigation, effect of acid rain on crop Vigna radiata was studied.
The effect of acid rain on change in soil fertility was detected in
which pH of control sample was 6.5 and pH of 1% H2SO4 and 1%
HNO3 were 3.5. Nitrogen nitrate in soil was high in 1% HNO3 treated
soil & Control sample. Ammonium nitrogen in soil was low in 1%
HNO3 & H2SO4 treated soil. Ammonium nitrogen was medium in
control and other samples. The effect of acid rain on seed
germination on 3rd day of germination control sample growth was
6.1cm with plumule 0.001% HNO3 & 0.001% H2SO4 was 5.5cm
with plumule and 8cm with plumule. On 10th day fungal growth was
observed in 1% and 0.1% H2SO4 concentrations when all plants were
dead. The effect of acid rain on crop productivity was investigated on
3rd day roots were developed in plants. On 12th day Vigna radiata
showed more growth in 0.1% HNO3 and 0.1% H2SO4 treated plants
as compare to control plants. On 20th day development of
discoloration of plant pigments were observed on acid treated plants
leaves. On 34th day Vigna radiata showed flower in 0.1% HNO3,
0.01% HNO3 and 0.01% H2SO4treated plants and no flowers were
observed on control plants. On 42th day 0.1% HNO3, 0.01% HNO
and 0.01% H2SO4 treated Vigna radiata variety and control plants
were showed seeds on plants. In Vigna radiate variety 0.1%, 0.01%
HNO3, 0.01% H2SO4treated plants were dead on 46th day and fungal
growth was observed. The toxicological study was carried out on
Vigna radiata plants exposed to 1% HNO3 cells were damaged more
than 1% H2SO4. Leaf sections exposed to 0.001% HNO3 & H2SO4
showed less damaged of cells and pigmentation observed in entire
slide when compare with control plant.
Abstract: Our work is part of the heterogeneous data
integration, with the definition of a structural and semantic mediation
model. Our aim is to propose architecture for the heterogeneous
sources metadata mediation, represented by XML, RDF and RuleML
models, providing to the user the metadata transparency. This, by
including data structures, of natures fundamentally different, and
allowing the decomposition of a query involving multiple sources, to
queries specific to these sources, then recompose the result.
Abstract: This study examines the design and construction of AC Electronics load surge protection in order to carry electric surge load arisen from faults in low voltage electricity system (single phase/220V) by using the principle of electronics load clamping voltage during induction period so that electric voltage could go through to safe load and continue to work. The qualification of the designed device could prevent both transient over voltage and voltage swell. Both will work in cooperation, resulting in the ability to improve and modify the quality of electrical power in Thailand electricity distribution system more effective than the past and help increase the lifetime of electric appliances, electric devices, and electricity protection equipments.
Abstract: Graph rewriting-based visual model processing is a
widely used technique for model transformation. Visual model
transformations often need to follow an algorithm that requires a
strict control over the execution sequence of the transformation steps.
Therefore, in Visual Model Processors (VMPs) the execution order
of the transformation steps is crucial. This paper presents the visual
control flow support of Visual Modeling and Transformation System
(VMTS), which facilitates composing complex model
transformations of simple transformation steps and executing them.
The VMTS Visual Control Flow Language (VCFL) uses stereotyped
activity diagrams to specify control flow structures and OCL
constraints to choose between different control flow branches. This
paper introduces VCFL, discusses its termination properties and
provides an algorithm to support the termination analysis of VCFL
transformations.
Abstract: Vibration characteristics of subcooled flow boiling on
thin and long structures such as a heating rod were recently
investigated by the author. The results show that the intensity of the
subcooled boiling-induced vibration (SBIV) was influenced strongly
by the conditions of the subcooling temperature, linear power density
and flow velocity. Implosive bubble formation and collapse are the
main nature of subcooled boiling, and their behaviors are the only
sources to originate from SBIV. Therefore, in order to explain the
phenomenon of SBIV, it is essential to obtain reliable information
about bubble behavior in subcooled boiling conditions. This was
investigated at different conditions of coolant subcooling
temperatures of 25 to 75°C, coolant flow velocities of 0.16 to
0.53m/s, and linear power densities of 100 to 600 W/cm. High speed
photography at 13,500 frames per second was performed at these
conditions. The results show that even at the highest subcooling
condition, the absolute majority of bubbles collapse very close to the
surface after detaching from the heating surface. Based on these
observations, a simple model of surface tension and momentum
change is introduced to offer a rough quantitative estimate of the
force exerted on the heating surface during the bubble ebullition. The
formation of a typical bubble in subcooled boiling is predicted to
exert an excitation force in the order of 10-4 N.
Abstract: This paper presents an experimental investigation using Acoustic Emission (AE) technology to monitor sand transportation in multiphase flow. The investigations were undertaken on three-phase (air-water-sand) flow in a horizontal pipe where the superficial gas velocity (VSG) had a range of between 0.2msˉ¹ to 2.0msˉ¹ and superficial liquid velocity (VSL) had a range of between 0.2msˉ¹ to 1.0msˉ¹. The experimental findings clearly show a correlation exists between AE energy levels, sand concentration, superficial gas velocity (VSG), and superficial liquid velocity (VSL).
Abstract: The understanding of the system level of biological behavior and phenomenon variously needs some elements such as gene sequence, protein structure, gene functions and metabolic pathways. Challenging problems are representing, learning and reasoning about these biochemical reactions, gene and protein structure, genotype and relation between the phenotype, and expression system on those interactions. The goal of our work is to understand the behaviors of the interactions networks and to model their evolution in time and in space. We propose in this study an ontological meta-model for the knowledge representation of the genetic regulatory networks. Ontology in artificial intelligence means the fundamental categories and relations that provide a framework for knowledge models. Domain ontology's are now commonly used to enable heterogeneous information resources, such as knowledge-based systems, to communicate with each other. The interest of our model is to represent the spatial, temporal and spatio-temporal knowledge. We validated our propositions in the genetic regulatory network of the Aarbidosis thaliana flower
Abstract: An effort to find out the smaller size of cuttings for propagation of Morus alba was made in experimental area Department of Forestry, Range Management and Wildlife, University of Agriculture, Faisalabad, Pakistan. Different size of cuttings i.e. 2", 4", 6" and 8" were planted in polythene tubes of 3.5"x7". The effort was also made to compare the performance of cuttings in open air and in polythene low tunnel. Root length, number of root branches, root diameter and root fresh and dry weight were found maximum in two inches cuttings while minimum in four inches cuttings. Root growth was found maximum in open air as compared to under polythene sheet.
Abstract: The antioxidant compounds are needed for the food, beverages, and pharmaceuticals industry. For this purpose, an appropriate method is required to measure the antioxidant properties in various types of samples. Spectrophotometric method usually used has some weaknesses, including the high price, long sample preparation time, and less sensitivity. Among the alternative methods developed to overcome these weaknesses is antioxidant biosensor based on superoxide dismutase (SOD) enzyme. Therefore, this study was carried out to measure the SOD activity originating from Deinococcus radiodurans and to determine its kinetics properties. Carbon paste electrode modified with ferrocene and immobilized SOD exhibited anode and cathode current peak at potential of +400 and +300mv respectively, in both pure SOD and SOD of D. radiodurans. This indicated that the current generated was from superoxide catalytic dismutation reaction by SOD. Optimum conditions for SOD activity was at pH 9 and temperature of 27.50C for D. radiodurans SOD, and pH 11 and temperature of 200C for pure SOD. Dismutation reaction kinetics of superoxide catalyzed by SOD followed the Lineweaver-Burk kinetics with D. radiodurans SOD KMapp value was smaller than pure SOD. The result showed that D. radiodurans SOD had higher enzyme-substrate affinity and specificity than pure SOD. It concluded that D. radiodurans SOD had a great potential as biological recognition component for antioxidant biosensor.
Abstract: Global temperature had increased by about 0.5oC over
the past century, increasing temperature leads to a loss or a decrease
of soil organic matter (SOM). Whereas soil organic matter in many
tropical soils is less stable than that of temperate soils, and it will be
easily affected by climate change. Therefore, conservation of soil
organic matter is urgent issue nowadays. This paper presents the
effect of different doses (5%, 15%) of Ca-type zeolite in conjunction
with organic manure, applied to soil samples from Philippines,
Paraguay and Japan, on the decomposition resistance of soil organic
matter under high temperature. Results showed that a remain or
slightly increase the C/N ratio of soil. There are an increase in
percent of humic acid (PQ) that extracted with Na4P2O7. A decrease
of percent of free humus (fH) after incubation was determined. A
larger the relative color intensity (RF) value and a lower the color
coefficient (6logK) value following increasing zeolite rates leading
to a higher degrees of humification. The increase in the aromatic
condensation of humic acid (HA) after incubation, as indicates by the
decrease of H/C and O/C ratios of HA. This finding indicates that the
use of zeolite could be beneficial with respect to SOM conservation
under global warming condition.
Abstract: This study investigated the effect of oxygen and
micro-cracking on the flotation of low grade nickel sulphide ore. The
ore treated contained serpentine minerals which have a history of
being difficult to process efficiently. The use of oxygen as a bubbling
gas has been noted to be effective because it increases the pulp
potential. The desired effect of micro cracking the ore is that the
nickel sulphide minerals will become activated and this activation
will render these minerals more susceptible to react with potassium
amyl xanthate collectors, resulting in a higher recovery of nickel and
hinder the recovery of other undesired minerals contained in the ore.
Higher nickel recoveries were obtained when pure oxygen was used
as a bubbling gas rather than the conventional air. Microwave
cracking favored the recovery of nickel.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9
Abstract: A modified Genetic Algorithm (GA) based optimal selection of parameters for Automatic Generation Control (AGC) of multi-area electric energy systems is proposed in this paper. Simulations on multi-area reheat thermal system with and without consideration of nonlinearity like governor dead band followed by 1% step load perturbation is performed to exemplify the optimum parameter search. In this proposed method, a modified Genetic Algorithm is proposed where one point crossover with modification is employed. Positional dependency in respect of crossing site helps to maintain diversity of search point as well as exploitation of already known optimum value. This makes a trade-off between exploration and exploitation of search space to find global optimum in less number of generations. The proposed GA along with decomposition technique as developed has been used to obtain the optimum megawatt frequency control of multi-area electric energy systems. Time-domain simulations are conducted with trapezoidal integration along with decomposition technique. The superiority of the proposed method over existing one is verified from simulations and comparisons.
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: Due to the low heavy metal concentrations, the
bottom ash from a 32 MW municipal district heating plant was
determined to be a potential forest fertilizer as such. However,
additional Ca would be needed, because its Ca concentration of 1.9-
% (d.w.) was lower than the statutory Finnish minimum limit value
of 6.0-% (d.w.) for Ca in forest fertilizer. Due to the elevated As
concentration (53.0 mg/kg; d.w.) in the fly ash from the 32 MW
municipal district heating plant, and Cr concentration (620 mg/kg;
d.w.) in the ash fraction (i.e. mixture of the bottom ash and fly ash)
from the 6 MW municipal district heating plant, which exceed the
limit values of 30 mg/kg (d.w.) and 300 mg/kg (d.w.) for As and Cr,
respectively, these residues are not suitable as forest fertilizers.
Although these ash fractions cannot be used as a forest fertilizer as
such, they can be used for the landscaping of landfills or in industrial
and other areas that are closed to the public. However, an
environmental permit is then needed.
Abstract: In today-s modern world, the number of vehicles is
increasing on the road. This causes more people to choose walking
instead of traveling using vehicles. Thus, proper planning of
pedestrians- paths is important to ensure the safety of pedestrians in a
walking area. Crowd dynamics study the pedestrians- behavior and
modeling pedestrians- movement to ensure safety in their walking paths.
To date, many models have been designed to ease pedestrians-
movement. The Social Force Model is widely used among researchers
as it is simpler and provides better simulation results. We will discuss
the problem regarding the ritual of circumambulating the Ka-aba
(Tawaf) where the entrances to this area are usually congested which
worsens during the Hajj season. We will use the computer simulation
model SimWalk which is based on the Social Force Model to simulate
the movement of pilgrims in the Tawaf area. We will first discuss the
effect of uni and bi-directional flows at the gates. We will then restrict
certain gates to the area as the entrances only and others as exits only.
From the simulations, we will study the effect of the distance of other
entrances from the beginning line and their effects on the duration of
pilgrims circumambulate Ka-aba. We will distribute the pilgrims at the
different entrances evenly so that the congestion at the entrances can be
reduced. We would also discuss the various locations and designs of
barriers at the exits and its effect on the time taken for the pilgrims to
exit the Tawaf area.
Abstract: This paper presents and discusses the numerical simulations of transient laminar natural convection cooling of high Prandtl number fluids in cubical cavities, in which the six walls of the cavity are subjected to a step change in temperature. The effect of the fluid Prandtl number on the heat transfer coefficient is studied for three different fluids (Golden Syrup, Glycerin and Glycerin-water solution 50%). The simulations are performed at two different Rayleigh numbers (5·106 and 5·107) and six different Prandtl numbers (3 · 105 ≥Pr≥ 50). Heat conduction through the cavity glass walls is also considered. The propsed correlations of the averaged heat transfer coefficient (N u) showed that it is dependant on the initial Ra and almost independent on P r. The instantaneous flow patterns, temperature contours and time evolution of volume averaged temperature and heat transfer coefficient are presented and analyzed.