Abstract: A comparison of activity and stability of the as-formed
Pt/C, Pt-Co and Pt-Pd/C electrocatalysts, prepared by a combined
approach of impregnation and seeding, was performed. According to
the activity test in a single Proton Exchange Membrane (PEM) fuel
cell, the Oxygen Reduction Reaction (ORR) activity of the Pt-M/C
electrocatalyst was slightly lower than that of Pt/C. The j0.9 V and
E10 mA/cm2 of the as-prepared electrocatalysts increased in the order of
Pt/C > Pt-Co/C > Pt-Pd/C. However, in the medium-to-high current
density region, Pt-Pd/C exhibited the best performance. With regard to
their stability in a 0.5 M H2SO4 electrolyte solution, the
electrochemical surface area decreased as the number of rounds of
repetitive potential cycling increased due to the dissolution of the
metals within the catalyst structure. For long-term measurement, Pt-
Pd/C was the most stable than the other three electrocatalysts.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: Currently, continuous two-phase decanter process
used for olive oil production is the more internationally widespread.
The wastewaters generated from this industry (OMW) are a real
environmental problem because of its high organic load. Among
proposed treatments for these wastewaters, advanced oxidation
technologies (Fenton, ozone, photoFenton, etc.) are the most
favourable. The direct application of these processes is somewhat
expensive. Therefore, the application of a previous stage based on a
flocculation-sedimentation operation is of high importance. In this
research five commercial flocculants (three cationic, and two anionic)
have been used to achieve the separation of phases (liquid clarifiedsludge).
For each flocculant, different concentrations (0-1000 mg/L)
have been studied. In these experiments, sludge volume formed and
the final water quality were determined. The final removal
percentages of total phenols (11.3-25.1%), COD (5.6-20.4%), total
carbon (2.3-26.5%), total organic carbon (1.50-23.8%), total nitrogen
(1.45-24.8%), and turbidity (27.9-61.4%) were determined. The
variation on electric conductivity reduction percentage (1-8%) was
also determined. Finally, the best flocculants with highest removal
percentages have been determined (QG2001 and Flocudex CS49).
Abstract: Evidence shows that start-ups success is positively
correlated with the launch of the first product. However, new ventures
are seldom able to acquire abundant resources for new product
development (NPD), which means that entrepreneurs may depend on
personal creativity instead of physical investments to achieve and
accelerate innovation speed. This study accentuates the role of
entrepreneurial bricolage, which defined as making do by applying
combinations of the resources at hand to new problems and
opportunities, in the relations of creative self-efficacy and innovation
speed. This study uses the multiple regression analysis to test the
hypotheses in a sample of 203 start-ups operating in various creative
markets in Taiwan. Results reveal that creative self-efficacy is
positively and directly associated with innovation speed, whereas
entrepreneurial bricolage plays a full mediator. These findings offer
important theoretical and practical implications.
Abstract: Haynes 25 alloy (also known as L-605 alloy) is cobalt
based super alloy which has widely applications such as aerospace
industry, turbine and furnace parts, power generators and heat
exchangers and petroleum refining components due to its excellent
characteristics. However, the workability of this alloy is more
difficult compared to normal steels or even stainless. In present work,
an experimental investigation was performed under cryogenic
cooling to determine cutting tool wear patterns and obtain optimal
cutting parameters in turning of cobalt based superalloy Haynes 25.
In experiments, uncoated carbide tool was used and cutting speed (V)
and feed rate (f) were considered as test parameters. Tool wear
(VBmax) were measured for process performance indicators.
Analysis of variance (ANOVA) was performed to determine the
importance of machining parameters.
Abstract: Amoxicillin is an antibiotic which is widely used to
treat various infections in both human beings and animals. However,
when amoxicillin is released into the environment, it is a major
problem. Amoxicillin causes bacterial resistance to these drugs and
failure of treatment with antibiotics. Liquid membrane is of great
interest as a promising method for the separation and recovery of the
target ions from aqueous solutions due to the use of carriers for the
transport mechanism, resulting in highly selectivity and rapid
transportation of the desired metal ions. The simultaneous processes
of extraction and stripping in a single unit operation of liquid
membrane system are very interesting. Therefore, it is practical to
apply liquid membrane, particularly the HFSLM for industrial
applications as HFSLM is proved to be a separation process with
lower capital and operating costs, low energy and extractant with
long life time, high selectivity and high fluxes compared with solid
membranes. It is a simple design amenable to scaling up for industrial
applications. The extraction and recovery for (Amoxicillin) through
the hollow fiber supported liquid membrane (HFSLM) using
aliquat336 as a carrier were explored with the experimental data. The
important variables affecting on transport of amoxicillin viz.
extractant concentration and operating time were investigated. The
highest AMOX- extraction percentages of 85.35 and Amoxicillin
stripping of 80.04 were achieved with the best condition at 6 mmol/L
[aliquat336] and operating time 100 min. The extraction reaction
order (n) and the extraction reaction rate constant (kf) were found to
be 1.00 and 0.0344 min-1, respectively.
Abstract: Construction projects are information intensive in
nature and involve many activities that are related to each other.
Wireless technologies can be used to improve the accuracy and
timeliness of data collected from construction sites and shares it with
appropriate parties. Nonetheless, the construction industry tends to be
conservative and shows hesitation to adopt new technologies. A main
concern for owners, contractors or any person in charge on a job site
is the cost of the technology in question. Wireless technologies are
not cheap. There are a lot of expenses to be taken into consideration,
and a study should be completed to make sure that the importance
and savings resulting from the usage of this technology is worth the
expenses. This research attempts to assess the effectiveness of using
the appropriate wireless technologies based on criteria such as
performance, reliability, and risk. The assessment is based on a utility
function model that breaks down the selection issue into alternatives
attribute. Then the attributes are assigned weights and single
attributes are measured. Finally, single attribute are combined to
develop one single aggregate utility index for each alternative.
Abstract: We used live E. coli containing synthetic genetic
oscillators to study how the degree of synchrony between the genetic
circuits of sister cells changes with temperature. We found that both
the mean and the variability of the degree of synchrony between the
fluorescence signals from sister cells are affected by temperature.
Also, while most pairs of sister cells were found to be highly
synchronous in each condition, the number of asynchronous pairs
increased with increasing temperature, which was found to be due to
disruptions in the oscillations. Finally we provide evidence that these
disruptions tend to affect multiple generations as opposed to
individual cells. These findings provide insight in how to design
more robust synthetic circuits and in how cell division can affect their
dynamics.
Abstract: In this work new macroporous Ni electrodes modified
with Au nanoparticles for hydrogen production have been developed.
The supporting macroporous Ni electrodes have been obtained by
means of the electrodeposition at high current densities. Then, the Au
nanoparticles were synthesized and added to the electrode surface.
The electrocatalytic behaviour of the developed electrocatalysts was
studied by means of pseudo-steady-state polarization curves,
electrochemical impedance spectroscopy (EIS) and hydrogen
discharge curves. The size of the Au synthetized nanoparticles shows
a monomodal distribution, with a very sharp band between 10 and 50
nm. The characteristic parameters d10, d50 and d90 were 14, 20 and
31 nm respectively. From Tafel polarization data has been concluded
that the Au nanoparticles improve the catalytic activity of the
developed electrodes towards the HER respect to the macroporous Ni
electrodes. EIS permits to obtain the electrochemically active area by
means of the roughness factor value. All the developed electrodes
show roughness factor values in the same order of magnitude. From
the activation energy results it can be concluded that the Au
nanoparticles improve the intrinsic catalytic activity of the
macroporous Ni electrodes.
Abstract: In this paper, the cable model of dendrites have been
considered. The dendrites are cylindrical cables of various segments
having variable length and reducing radius from start point at synapse
and end points. For a particular event signal being received by a
neuron in response only some dendrite are active at a particular
instance. Initial current signals with different current flows in
dendrite are assumed. Due to overlapping and coupling of active
dendrite, they induce currents in the dendrite segments of each other
at a particular instance. But how these currents are induced in the
various segments of active dendrites due to coupling between these
dendrites, It is not presented in the literature. Here the paper presents
a model for induced currents in active dendrite segments due to
mutual coupling at the starting instance of an activity in dendrite. The
model is as discussed further.
Abstract: Mustard leaves are rich in folates, vitamin A, K and
B-complex. Mustard greens are low in calories and fats and rich in
dietary fiber. They are rich in potassium, manganese, iron, copper,
calcium, magnesium and low in sodium. It is very rich in antioxidants
and Phytonutrients. For the optimization of process variables
(moisture content and mustard leave powder), the experiments were
conducted according to central composite Face Centered Composite
design of RSM. The mustard leaves powder was replaced with
composite flour (a combination of rice, chickpea and corn in the ratio
of 70:15:15). The extrudate was extruded in a twin screw extruder at
a barrel temperature of 120°C. The independent variables were
mustard leaves powder (2-10 %) and moisture content (12-20 %).
Responses analyzed were bulk density, water solubility index, water
absorption index, lateral expansion, antioxidant activity, total
phenolic content, and overall acceptability. The optimum conditions
obtained were 7.19 g mustard leaves powder in 100g premix having
16.8% moisture content (w.b).
Abstract: This study aims at developing a novel cold asphalt
concrete binder course mixture by using Ordinary Portland Cement
(OPC) as a replacement for conventional mineral filler (0%-100%)
with new by-product material (LJMU-A2) used as a supplementary
cementitious material. With this purpose, cold asphalt concrete binder
course mixtures with cationic emulsions were studied by means of
stiffness modulus whereas water sensitivity was assessed by
measuring the stiffness modulus ratio before and after sample
conditioning.
The results indicate that a substantial enhancement in the stiffness
modulus and a considerable improvement of water sensitivity
resistance is achieved by adding LJMU-A2 to the cold asphalt
mixtures as a supplementary cementitious material. Moreover, the
addition of LJMU-A2 to those mixtures leads to a stiffness modulus
after 2-day curing compared to that obtained with Portland cement,
which occurs after 7-day curing.
Abstract: The goal of the paper is to highlight the effect of the
building design and epicentral distance on the storey lateral
displacements, for several reinforced concrete buildings (6, 9 and 12
stories). These structures are subjected to seismic accelerations from
the Boumerdes earthquake (Algeria, May 21st, Mw = 6.8). Using the
response spectrum method (modal spectral approach), the analysis is
performed in both longitudinal and transverse directions. The
building design is expressed through the fundamental period and
epicentral distance is used to represent the earthquake effect variation
on storey lateral displacements and interstory drift for the considered
buildings.
Abstract: Cyberspace has become a more viable arena for
budding artists to share musical acts through digital forms. The
increasing relevance of online communities has attracted scholars
from various fields demonstrating its influence on social capital. This
paper extends this understanding of social capital among Filipino
music artists belonging to the SoundCloud Philippines Facebook
Group.
The study makes use of various qualitative data obtained from
key-informant interviews and participant observation of online and
physical encounters, analyzed using the case study approach.
Soundcloud Philippines has over seven-hundred members and is
composed of Filipino singers, instrumentalists, composers, arrangers,
producers, multimedia artists and event managers. Group interactions
are a mix of online encounters based on Facebook and SoundCloud
and physical encounters through meet-ups and events. Benefits
reaped from the community are informational, technical,
instrumental, promotional, motivational and social support. Under the
guidance of online group administrators, collaborative activities such
as music productions, concerts and events transpire. Most conflicts
and problems arising are resolved peacefully. Social capital in
SoundCloud Philippines is mobilized through recognition, respect
and reciprocity.
Abstract: This paper presents Carrier Sense Multiple Access
(CSMA) communication models based on SoC design methodology.
Such a model can be used to support the modeling of the complex
wireless communication systems. Therefore, the use of such
communication model is an important technique in the construction
of high-performance communication. SystemC has been chosen
because it provides a homogeneous design flow for complex designs
(i.e. SoC and IP-based design). We use a swarm system to validate
CSMA designed model and to show how advantages of incorporating
communication early in the design process. The wireless
communication created through the modeling of CSMA protocol that
can be used to achieve communication between all the agents and to
coordinate access to the shared medium (channel).
Abstract: Interstitial free steels possess better formability and
have many applications in automotive industries. Forming limit
diagrams (FLDs) indicate the formability of materials which can be
determined by experimental and finite element (FE) simulations.
FLDs were determined experimentally by LDH test, utilizing optical
strain measurement system for measuring the strains in different
width specimens and by FE simulations in Interstitial Free (IF) and
Interstitial Free High Strength (IFHS) steels. In this study, the
experimental and FE simulated FLDs are compared and also the
stress based FLDs were investigated.
Abstract: The Chair of Thermal Engineering at Poznan
University of Technology has been conducted research works on the
possibilities of using carbon nanostructures in energy and mechanics
applications for a couple of years. Those studies have provided results in a form of co-operation with foreign research centres, numerous publications and patent
applications.
Authors of this paper have studied the influence of multi-walled
carbon nanostructures on changes in static friction arising when steel
surfaces were moved. Tests were made using the original test stand
consisting of automatically controlled inclined plane driven by
precise stepper motors. Computer program created in the LabView
environment was responsible for monitoring of the stand operation,
accuracy of measurements and archiving the obtained results. Such a
solution enabled to obtain high accuracy and repeatability of all
conducted experiments.
Tests and analysis of the obtained results allowed us to determine
how additional layers of carbon nanostructures influenced on changes
of static friction coefficients. At the same time, we analyzed the
potential possibilities of applying nanostructures under consideration
in mechanics.
Abstract: Market is an important factor for start-ups to look into
during decision-making in product development and related areas.
Emerging country markets are more uncertain in terms of information
availability and institutional supports. The literature review of market
uncertainty reveals the need for identifying factors representing the
market uncertainty. This paper identifies factors for market
uncertainty using Exploratory Factor Analysis (EFA) and confirmed
the number of factor retention using an alternative factor retention
criterion ‘Parallel Analysis’. 500 entrepreneurs, engaged in start-ups
from all over India participated in the study. This paper concludes
with the factor structure of ‘market uncertainty’ having dimensions of
uncertainty in industry orientation, uncertainty in customer
orientation and uncertainty in marketing orientation.
Abstract: This paper presents an application of Artificial Neural
Network (ANN) algorithm for improving power system voltage
stability. The training data is obtained by solving several normal and
abnormal conditions using the Linear Programming technique. The
selected objective function gives minimum deviation of the reactive
power control variables, which leads to the maximization of
minimum Eigen value of load flow Jacobian. The considered reactive
power control variables are switchable VAR compensators, OLTC
transformers and excitation of generators. The method has been
implemented on a modified IEEE 30-bus test system. The results
obtain from the test clearly show that the trained neural network is
capable of improving the voltage stability in power system with a
high level of precision and speed.
Abstract: In this paper, the actuality of the study, and the role of
subjective well-being problem in modern psychology and the
comprehending of subjective well-being by current students is
defined. The purpose of this research is to educe peculiarities of
comprehending of subjective well-being by students with various
levels of emotional intelligence. Methods of research are adapted
Russian-Language questionnaire of K. Riff 'The scales of
psychological well-being'; emotional intelligence questionnaire of D.
V. Lusin. The research involved 72 students from different
universities and disciplines aged between 18 and 24. Analyzing the
results of the studies, it can be concluded that the understanding of
happiness in different groups of students with high and low levels of
overall emotional intelligence is different, as well as differentiated by
gender. Students with a higher level of happiness possess more
capacity and higher need to control their emotions, to cause and
maintain the desired emotions and control something undesirable.