Abstract: In many applications, magnetic suspension systems
are required to operate over large variations in air gap. As a result,
the nonlinearities inherent in most types of suspensions have a
significant impact on performance. Specifically, it may be difficult to
design a linear controller which gives satisfactory performance,
stability, and disturbance rejection over a wide range of operating
points. in this paper an optimal controller based on discontinuous
mathematical model of the system for an electromagnetic suspension
system which is applied in magnetic trains has been designed .
Simulations show that the new controller can adapt well to the
variance of suspension mass and gap, and keep its dynamic
performance, thus it is superior to the classic controller.
Abstract: A dead leg is a typical subsea production system
component. CFD is required to model heat transfer within the dead
leg. Unfortunately its solution is time demanding and thus not
suitable for fast prediction or repeated simulations. Therefore there is
a need to create a thermal FEA model, mimicking the heat flows and
temperatures seen in CFD cool down simulations.
This paper describes the conventional way of tuning and a new
automated way using parametric model order reduction (PMOR)
together with an optimization algorithm. The tuned FE analyses
replicate the steady state CFD parameters within a maximum error in
heat flow of 6 % and 3 % using manual and PMOR method
respectively. During cool down, the relative error of the tuned FEA
models with respect to temperature is below 5% comparing to the
CFD. In addition, the PMOR method obtained the correct FEA setup
five times faster than the manually tuned FEA.
Abstract: In the world of Peer-to-Peer (P2P) networking
different protocols have been developed to make the resource sharing
or information retrieval more efficient. The SemPeer protocol is a
new layer on Gnutella that transforms the connections of the nodes
based on semantic information to make information retrieval more
efficient. However, this transformation causes high clustering in the
network that decreases the number of nodes reached, therefore the
probability of finding a document is also decreased. In this paper we
describe a mathematical model for the Gnutella and SemPeer
protocols that captures clustering-related issues, followed by a
proposition to modify the SemPeer protocol to achieve moderate
clustering. This modification is a sort of link management for the
individual nodes that allows the SemPeer protocol to be more
efficient, because the probability of a successful query in the P2P
network is reasonably increased. For the validation of the models, we
evaluated a series of simulations that supported our results.
Abstract: This paper proposes a solution to the motion planning
and control problem of a point-mass robot which is required to move
safely to a designated target in a priori known workspace cluttered
with fixed elliptical obstacles of arbitrary position and sizes. A
tailored and unique algorithm for target convergence and obstacle
avoidance is proposed that will work for any number of fixed
obstacles. The control laws proposed in this paper also ensures that
the equilibrium point of the given system is asymptotically stable.
Computer simulations with the proposed technique and applications
to a planar (RP) manipulator will be presented.
Abstract: A new topology of unified power quality conditioner
(UPQC) is proposed for different power quality (PQ) improvement in
a three-phase four-wire (3P-4W) distribution system. For neutral
current mitigation, a star-hexagon transformer is connected in shunt
near the load along with three-leg voltage source inverters (VSIs)
based UPQC. For the mitigation of source neutral current, the uses of
passive elements are advantageous over the active compensation due
to ruggedness and less complexity of control. In addition to this, by
connecting a star-hexagon transformer for neutral current mitigation
the over all rating of the UPQC is reduced. The performance of the
proposed topology of 3P-4W UPQC is evaluated for power-factor
correction, load balancing, neutral current mitigation and mitigation
of voltage and currents harmonics. A simple control algorithm based
on Unit Vector Template (UVT) technique is used as a control
strategy of UPQC for mitigation of different PQ problems. In this
control scheme, the current/voltage control is applied over the
fundamental supply currents/voltages instead of fast changing APFs
currents/voltages, thereby reducing the computational delay.
Moreover, no extra control is required for neutral source current
compensation; hence the numbers of current sensors are reduced. The
performance of the proposed topology of UPQC is analyzed through
simulations results using MATLAB software with its Simulink and
Power System Block set toolboxes.
Abstract: We apply a particle tracking technique to track the motion of individual pathogenic Leptospira. We observe and capture images of motile Leptospira by means of CCD and darkfield microscope. Image processing, statistical theories and simulations are used for data analysis. Based on trajectory patterns, mean square displacement, and power spectral density characteristics, we found that the motion modes are most likely to be directed motion mode (70%) and the rest are either normal diffusion or unidentified mode. Our findings may support the fact that why leptospires are very well efficient toward targeting internal tissues as a result of increase in virulence factor.
Abstract: A two-dimensional numerical simulation of crossflow
around four cylinders in an in-line rectangular configuration is
studied by using the lattice Boltzmann method (LBM). Special
attention is paid to the effect of the spacing between the cylinders.
The Reynolds number ( Re ) is chosen to be e 100 R = and the
spacing ratio L / D is set at 0.5, 1.5, 2.5, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0
and 10.0. Results show that, as in the case of four cylinders in an inline
rectangular configuration , flow fields show four different
features depending on the spacing (single square cylinder, stable
shielding flow, wiggling shielding flow and a vortex shedding flow)
are observed in this study. The effects of spacing ratio on physical
quantities such as mean drag coefficient, Strouhal number and rootmean-
square value of the drag and lift coefficients are also presented.
There is more than one shedding frequency at small spacing ratios.
The mean drag coefficients for downstream cylinders are less than
that of the single cylinder for all spacing ratios. The present results
using the LBM are compared with some existing experimental data
and numerical studies. The comparison shows that the LBM can
capture the characteristics of the bluff body flow reasonably well and
is a good tool for bluff body flow studies.
Abstract: The construction of a civil structure inside a urban
area inevitably modifies the outdoor microclimate at the building
site. Wind speed, wind direction, air pollution, driving rain, radiation
and daylight are some of the main physical aspects that are subjected
to the major changes. The quantitative amount of these modifications
depends on the shape, size and orientation of the building and on its
interaction with the surrounding environment.The flow field over a
flat roof model building has been numerically investigated in order to
determine two-dimensional CFD guidelines for the calculation of the
turbulent flow over a structure immersed in an atmospheric boundary
layer. To this purpose, a complete validation campaign has been
performed through a systematic comparison of numerical simulations
with wind tunnel experimental data.Several turbulence models and
spatial node distributions have been tested for five different vertical
positions, respectively from the upstream leading edge to the
downstream bottom edge of the analyzed model. Flow field
characteristics in the neighborhood of the building model have been
numerically investigated, allowing a quantification of the capabilities
of the CFD code to predict the flow separation and the extension of
the recirculation regions.The proposed calculations have allowed the
development of a preliminary procedure to be used as a guidance in
selecting the appropriate grid configuration and corresponding
turbulence model for the prediction of the flow field over a twodimensional
roof architecture dominated by flow separation.
Abstract: This paper gives an overview of a deep drawing
process by pressurized liquid medium separated from the sheet by a
rubber diaphragm. Hydroforming deep drawing processing of sheet
metal parts provides a number of advantages over conventional
techniques. It generally increases the depth to diameter ratio possible
in cup drawing and minimizes the thickness variation of the drawn
cup. To explore the deformation mechanism, analytical and
numerical simulations are used for analyzing the drawing process of
an AA6061-T4 blank. The effects of key process parameters such as
coefficient of friction, initial thickness of the blank and radius
between cup wall and flange are investigated analytically and
numerically. The simulated results were in good agreement with the
results of the analytical model. According to finite element
simulations, the hydroforming deep drawing method provides a more
uniform thickness distribution compared to conventional deep
drawing and decreases the risk of tearing during the process.
Abstract: Electromagnetic flow meter by measuring the varying of magnetic flux, which is related to the velocity of conductive flow, can measure the rate of fluids very carefully and precisely. Electromagnetic flow meter operation is based on famous Faraday's second Law. In these equipments, the constant magnetostatic field is produced by electromagnet (winding around the tube) outside of pipe and inducting voltage that is due to conductive liquid flow is measured by electrodes located on two end side of the pipe wall. In this research, we consider to 2-dimensional mathematical model that can be solved by numerical finite difference (FD) solution approach to calculate induction potential between electrodes. The fundamental concept to design the electromagnetic flow meter, exciting winding and simulations are come out by using MATLAB and PDE-Tool software. In the last stage, simulations results will be shown for improvement and accuracy of technical provision.
Abstract: In this paper, an intelligent automatic parking control method is proposed. First, the dynamical equation of the rear parking control is derived. Then a fuzzy logic control is proposed to perform the parking planning process. Further, a rear neural network is proposed for the steering control. Through the simulations and experiments, the intelligent auto-parking mode controllers have been shown to achieve the demanded goals with satisfactory control performance and to guarantee the system robustness under parametric variations and external disturbances. To improve some shortcomings and limitations in conventional parking mode control and further to reduce consumption time and prime cost.
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: In this paper back-propagation artificial neural
network (BPANN) is employed to predict the limiting drawing ratio
(LDR) of the deep drawing process. To prepare a training set for
BPANN, some finite element simulations were carried out. die and
punch radius, die arc radius, friction coefficient, thickness, yield
strength of sheet and strain hardening exponent were used as the
input data and the LDR as the specified output used in the training of
neural network. As a result of the specified parameters, the program
will be able to estimate the LDR for any new given condition.
Comparing FEM and BPANN results, an acceptable correlation was
found.
Abstract: This paper describes about dynamic reconfiguration to
miniaturize arithmetic circuits in general-purpose processor. Dynamic
reconfiguration is a technique to realize required functions by
changing hardware construction during operation. The proposed
arithmetic circuit performs floating-point arithmetic which is
frequently used in science and technology. The data format is
floating-point based on IEEE754. The proposed circuit is designed
using VHDL, and verified the correct operation by simulations and
experiments.
Abstract: In this paper we present our results on the performance analysis of a multi-product manufacturing line. We study the influence of external perturbations, intermediate buffer content and the number of manufacturing stages on the production tracking error of each machine in the multi-product line operated under a surplusbased production control policy. Starting by the analysis of a single machine with multiple production stages (one for each product type), we provide bounds on the production error of each stage. Then, we extend our analysis to a line of multi-stage machines, where similarly, bounds on each production tracking error for each product type, as well as buffer content are obtained. Details on performance of the closed-loop flow line model are illustrated in numerical simulations.
Abstract: Restoration of endodontically treated teeth is a
common problem in dentistry, related to the fractures occurring in
such teeth and to concentration of forces little information regarding
variation of basic preparation guidelines in stress distribution has
been available. To date, there is still no agreement in the literature
about which material or technique can optimally restore
endodontically treated teeth. The aim of the present study was to
evaluate the influence of the core height and restoration materials on
corono-radicular restored upper first premolar. The first step of the
study was to achieve 3D models in order to analyze teeth, dowel and
core restorations and overlying full ceramic crowns. The FEM model
was obtained by importing the solid model into ANSYS finite
element analysis software. An occlusal load of 100 N was conducted,
and stresses occurring in the restorations, and teeth structures were
calculated. Numerical simulations provide a biomechanical
explanation for stress distribution in prosthetic restored teeth. Within
the limitations of the present study, it was found that the core height
has no important influence on the stress generated in coronoradicular
restored premolars. It can be drawn that the cervical regions
of the teeth and restorations were subjected to the highest stress
concentrations.
Abstract: This paper discusses a systematic design of a Σ-Δ fractional-N Phase-Locked Loop based on HDL behavioral modeling. The proposed design consists in describing the mixed behavior of this PLL architecture starting from the specifications of each building block. The HDL models of critical PLL blocks have been described in VHDL-AMS to predict the different specifications of the PLL. The effect of different noise sources has been efficiently introduced to study the PLL system performances. The obtained results are compared with transistor-level simulations to validate the effectiveness of the proposed models for wireless applications in the frequency range around 2.45 GHz.
Abstract: In this paper, novel statistical sampling based equalization techniques and CNN based detection are proposed to increase the spectral efficiency of multiuser communication systems over fading channels. Multiuser communication combined with selective fading can result in interferences which severely deteriorate the quality of service in wireless data transmission (e.g. CDMA in mobile communication). The paper introduces new equalization methods to combat interferences by minimizing the Bit Error Rate (BER) as a function of the equalizer coefficients. This provides higher performance than the traditional Minimum Mean Square Error equalization. Since the calculation of BER as a function of the equalizer coefficients is of exponential complexity, statistical sampling methods are proposed to approximate the gradient which yields fast equalization and superior performance to the traditional algorithms. Efficient estimation of the gradient is achieved by using stratified sampling and the Li-Silvester bounds. A simple mechanism is derived to identify the dominant samples in real-time, for the sake of efficient estimation. The equalizer weights are adapted recursively by minimizing the estimated BER. The near-optimal performance of the new algorithms is also demonstrated by extensive simulations. The paper has also developed a (Cellular Neural Network) CNN based approach to detection. In this case fast quadratic optimization has been carried out by t, whereas the task of equalizer is to ensure the required template structure (sparseness) for the CNN. The performance of the method has also been analyzed by simulations.
Abstract: Climate change has profound consequences for the agriculture of south-eastern Australia and its climate-induced water shortage in the Murray-Darling Basin. Post Keynesian Economics (PKE) macro-dynamics, along with Kaleckian investment and growth theory, are used to develop an ecological-economic system dynamics model of this complex nonlinear river basin system. The Murray- Darling Basin Simulation Model (MDB-SM) uses the principles of PKE to incorporate the fundamental uncertainty of economic behaviors of farmers regarding the investments they make and the climate change they face, particularly as regards water ecosystem services. MDB-SM provides a framework for macroeconomic policies, especially for long-term fiscal policy and for policy directed at the sustainability of agricultural water, as measured by socio-economic well-being considerations, which include sustainable consumption and investment in the river basin. The model can also reproduce other ecological and economic aspects and, for certain parameters and initial values, exhibit endogenous business cycles and ecological sustainability with realistic characteristics. Most importantly, MDBSM provides a platform for the analysis of alternative economic policy scenarios. These results reveal the importance of understanding water ecosystem adaptation under climate change by integrating a PKE macroeconomic analytical framework with the system dynamics modelling approach. Once parameterised and supplied with historical initial values, MDB-SM should prove to be a practical tool to provide alternative long-term policy simulations of agricultural water and socio-economic well-being.
Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.