Abstract: Polymeric composites are being increasingly used as
repair material for repairing critical infrastructures such as building,
bridge, pressure vessel, piping and pipeline. Technique in repairing
damaged pipes is one of the major concerns of pipeline owners.
Considerable researches have been carried out on the repair of
corroded pipes using composite materials. This article attempts a
short review of the subject matter to provide insight into various
techniques used in repairing corroded pipes, focusing on a wide range
of composite repair systems. These systems including pre-cured
layered, flexible wet lay-up, pre-impregnated, split composite sleeve
and flexible tape systems. Both advantages and limitations of these
repair systems were highlighted. Critical technical aspects have been
discussed through the current standards and practices. Research gaps
and future study scopes in achieving more effective design
philosophy are also presented.
Abstract: This experimental study consists of a characterization
of epoxy grout where an amount of 2% of graphene nanoplatelets
particles were added to commercial epoxy resin to evaluate their
behavior regarding neat epoxy resin. Compressive tests, tensile tests
and flexural tests were conducted to study the effect of graphene
nanoplatelets on neat epoxy resin. By comparing graphene-based and
neat epoxy grout, there is no significant increase of strength due to
weak interface in the graphene nanoplatelets/epoxy composites.
From this experiment, the tension and flexural strength of graphenebased
epoxy grouts is slightly lower than ones of neat epoxy grout.
Nevertheless, the addition of graphene has produced more consistent
results according to a smaller standard deviation of strength.
Furthermore, the graphene has also improved the ductility of the
grout, hence reducing its brittle behaviour. This shows that the
performance of graphene-based grout is reliably predictable and able
to minimise sudden rupture. This is important since repair design of
damaged pipeline is of deterministic nature.
Abstract: Issues relating to the destructive phenomena that can
damage people and goods have returned to the centre of debate in
Italy with the increase in catastrophic episodes in recent years in a
country which is highly vulnerable to hydrological risk.
Environmental factors and geological and geomorphological
territorial characteristics play an important role in determining the
level of vulnerability and the natural tendency to risk. However, a
territory has also been subjected to the requirements of and
transformations of society and this brings other relevant factors. The
reasons for the increase in destructive phenomena are often to be
found in the territorial development models adopted. Stewardship of
the landscape and management of risk are related issues. This study aims to summarize the most relevant elements about
this connection and at the same time to clarify the role of
environmental risk assessment as a tool to aid in the sustainable
management of landscape. Finally, the study reflects on how regional
and urban planners deal with environmental risk and which aspects
should be monitored in order to adopt responsible and useful
interventions.
Abstract: The major environmental risk of soil pollution is the
contamination of groundwater by infiltration of organic and inorganic
pollutants which can cause a serious menace. To prevent this risk and
to protect the groundwater, we proceeded in this study to test the
reliability of a biosolid as barrier to prevent the migration of very
dangerous pollutants as ‘Cadmium’ through the different soil layers. In this study, we tried to highlight the effect of several parameters
such as: turbidity (different cycle of Hydration/Dehydration),
rainfall, effect of initial Cd(II) concentration and the type of soil.
These parameters allow us to find the most effective manner to
integrate this barrier in the soil. From the results obtained, we found a
significant effect of the barrier. Indeed, the recorded passing
quantities are lowest for the highest rainfall; we noted also that the
barrier has a better affinity towards higher concentrations; the most
retained amounts of cadmium has been in the top layer of the two
types of soil tested, while the lowest amounts of cadmium are
recorded in the bottom layers of soils.
Abstract: Hard coatings are widely used in cutting and forming
tool industries. Titanium Nitride (TiN) possesses good hardness,
strength, and corrosion resistance. The coating properties are
influenced by many process parameters. The coatings were deposited
on steel substrate by changing the process parameters such as
substrate temperature, nitrogen flow rate and target power in a D.C
planer magnetron sputtering. The structure of coatings were analysed
using XRD. The hardness of coatings was found using Micro
hardness tester. From the experimental data, a regression model was
developed and the optimum response was determined using Response
Surface Methodology (RSM).
Abstract: Rapid developments in technology in the present age
have made it necessary for communities to follow technological
developments and adapt themselves to these developments. One of
the fields that are most rapidly affected by these developments is
undoubtedly education. Determination of the attitudes of preservice
teachers, who live in an age of technology and get ready to raise
future individuals, is of paramount importance both educationally and
professionally. The purpose of this study was to analyze attitudes of
preservice teachers towards technology and some variables that
predict these attitudes (gender, daily duration of internet use, and the
number of technical devices owned). 329 preservice teachers
attending the education faculty of a large university in central Turkey
participated, on a volunteer basis, in this study, where relational
survey model was used as the research method. Research findings
reveal that preservice teachers’ attitudes towards technology are
positive and at the same time, the attitudes of male preservice
teachers towards technology are more positive than their female
counterparts. As a result of the stepwise multiple regression analysis
where factors predicting preservice teachers’ attitudes towards
technology, it was found that duration of daily internet use was the
strongest predictor of attitudes towards technology.
Abstract: Companies face increasing challenges in research due
to higher costs and risks. The intensifying technology complexity and
interdisciplinarity require unique know-how. Therefore, companies
need to decide whether research shall be conducted internally or
externally with partners. On the other hand, research institutes meet
increasing efforts to achieve good financing and to maintain high
research reputation. Therefore, relevant research topics need to be
identified and specialization of competency is necessary. However,
additional competences for solving interdisciplinary research projects
are also often required. Secured financing can be achieved by
bonding industry partners as well as public fundings. The realization
of faster and better research drives companies and research institutes
to cooperate in organized research networks, which are managed by
an administrative organization. For an effective and efficient
cooperation, necessary processes, roles, tools and a set of rules need
to be determined. Goal of this paper is to show the state-of-art
research and to propose a governance framework for organized
research networks.
Abstract: The need to protect our cultural heritage was stressed
on revitalization of historical city centers in communities. The main
aim of this research is to attract finance and activities to the historical
city centers through the citizens and municipalities participation
while cities expanded their boundaries toward suburban areas. Today
the main problems which facing to the most historical city centers, is
loss of their centrality through effect of urbanization on any point of
the cities which is the most important issue on neglect and
abandonment of the historical central area by decentralizing living,
commerce and public areas. This article evaluate the ways in which
city center revitalization can be effect on vitality and viability of the
central area in case of Naghshe Jahan square which situated at the
center of Isfahan city, Iran. Constructed between 1598 and 1629, it is
now an important historical site, and one of UNESCO's World
Heritage Sites.
Abstract: This first-attempt study revealed that decolorized
intermediates of azo dyes could act as redox mediators to assist
wastewater (WW) decolorization due to enhancement of
electron-transport phenomena. Electrochemical impedance spectra
indicated that hydroxyl and amino-substituent(s) were functional
group(s) as redox-mediator(s). As azo dyes are usually multiple
benzene-rings structured, their derived decolorized intermediates are
likely to play roles of electron shuttles due to lower barrier of energy
gap for electron shuttling. According to cyclic voltammetric profiles,
redox mediating characteristics of decolorized intermediates of azo
dyes (e.g., RBu171, RR198, RR141, RBk5) were clearly disclosed.
With supplementation of biodecolorized metabolites of RR141 and
198, decolorization performance of could be evidently augmented.
This study also suggested the optimal modes of microbial fuel cell
(MFC)-assisted WW decolorization would be plug-flow or batch
mode of operation with no mix. Single chamber-MFCs would be more
favourable than double chamber MFCs due to non-mixing contacting
reactor scheme for operation.
Abstract: River Hindon is an important river catering the
demand of highly populated rural and industrial cluster of western
Uttar Pradesh, India. Water quality of river Hindon is deteriorating at
an alarming rate due to various industrial, municipal and agricultural
activities. The present study aimed at identifying the pollution
sources and quantifying the degree to which these sources are
responsible for the deteriorating water quality of the river. Various
water quality parameters, like pH, temperature, electrical
conductivity, total dissolved solids, total hardness, calcium, chloride,
nitrate, sulphate, biological oxygen demand, chemical oxygen
demand, and total alkalinity were assessed. Water quality data
obtained from eight study sites for one year has been subjected to the
two multivariate techniques, namely, principal component analysis
and cluster analysis. Principal component analysis was applied with
the aim to find out spatial variability and to identify the sources
responsible for the water quality of the river. Three Varifactors were
obtained after varimax rotation of initial principal components using
principal component analysis. Cluster analysis was carried out to
classify sampling stations of certain similarity, which grouped eight
different sites into two clusters. The study reveals that the
anthropogenic influence (municipal, industrial, waste water and
agricultural runoff) was the major source of river water pollution.
Thus, this study illustrates the utility of multivariate statistical
techniques for analysis and elucidation of multifaceted data sets,
recognition of pollution sources/factors and understanding
temporal/spatial variations in water quality for effective river water
quality management.
Abstract: Over the last two decades, externally bonded fiber
reinforced polymer (FRP) composites bonded to concrete substrates
has become a popular method for strengthening reinforced concrete
(RC) highway and railway bridges. Such structures are exposed to
severe cyclic loading throughout their lifetime often resulting in
fatigue damage to structural components and a reduction in the
service life of the structure. Since experimental and numerical results
on the fatigue performance of FRP-to-concrete joints are still limited,
the current research focuses on assessing the fatigue performance of
externally bonded FRP-to-concrete joints using a direct shear test.
Some early results indicate that the stress ratio and the applied cyclic
stress level have a direct influence on the fatigue life of the externally
bonded FRP. In addition, a calibrated finite element model is
developed to provide further insight into the influence of certain
parameters such as: concrete strength, FRP thickness, number of
cycles, frequency, and stiffness on the fatigue life of the FRP-toconcrete
joints.
Abstract: In the present work, forming limit diagrams and strain
distribution profile diagrams for extra deep drawing steel at room and
elevated temperatures have been determined experimentally by
conducting stretch forming experiments by using designed and
fabricated warm stretchforming tooling setup. With the help of
forming Limit Diagrams (FLDs) and strain, distribution profile
diagrams the formability of Extra Deep Drawing steel has been
analyzed and co-related with mechanical properties like strain
hardening COEFFICIENT (n) and normal anisotropy (r−). Mechanical
properties of EDD steel from room temperature to 4500C were
determined and discussed the impact of temperature on the properties
like work hardening exponent (n) anisotropy (r-) and strength
coefficient of the material. In addition, the fractured surfaces after
stretching have undergone the some metallurgical investigations and
attempt has been made to co-relate with the formability of EDD steel
sheets. They are co-related and good agreement with FLDs at various
temperatures.
Abstract: Fluctuations of Schottky diode parameters in a
structure of the mixer are investigated. These fluctuations are
manifested in two ways. At the first, they lead to fluctuations in the
transfer factor that is lead to the amplitude fluctuations in the signal
of intermediate frequency. On the basis of the measurement data of
1/f noise of the diode at forward current, the estimation of a spectrum
of relative fluctuations in transfer factor of the mixer is executed.
Current dependence of the spectrum of relative fluctuations in
transfer factor of the mixer and dependence of the spectrum of
relative fluctuations in transfer factor of the mixer on the amplitude
of the heterodyne signal are investigated. At the second, fluctuations
in parameters of the diode lead to occurrence of 1/f noise in the
output signal of the mixer. This noise limits the sensitivity of the
mixer to the value of received signal.
Abstract: Sewage sludge is a biomass resource that can create a
solid fuel and electricity. Utilizing sewage sludge as a renewable
energy can contribute to the reduction of greenhouse gases. In Japan,
the "National Plan for the Promotion of Biomass Utilization" and the
“Priority Plan for Social Infrastructure Development" were approved
at cabinet meetings in December 2010 and August 2012, respectively,
to promote the energy utilization of sewage sludge. This study
investigated costs and greenhouse gas emission in different sewage
sludge treatments with technologies for energy from sewage sludge.
Expenses were estimated based on capital costs and O&M costs
including energy consumption of solid fuel plants and biogas power
generation plants for sewage sludge. Results showed that the cost of
sludge digestion treatment with solid fuel technologies was 8% lower
than landfill disposal. The greenhouse gas emission of sludge
digestion treatment with solid fuel technologies was also 6,390t as
CO2 smaller than landfill disposal. Biogas power generation reduced
the electricity of a wastewater treatment plant by 30% and the cost by
5%.
Abstract: This article developed an ion thruster optic system
sputter erosion depth numerical 3D model by IFE-PIC (Immersed
Finite Element-Particle-in-Cell) and Mont Carlo method, and
calculated the downstream surface sputter erosion rate of accelerator
grid; compared with LIPS-200 life test data. The results of the
numerical model are in reasonable agreement with the measured data.
Finally, we predicted the lifetime of the 20cm diameter ion thruster via
the erosion data obtained with the model. The ultimate result
demonstrated that under normal operating condition, the erosion rate
of the grooves wears on the downstream surface of the accelerator grid
is 34.6μm⁄1000h, which means the conservative lifetime until
structural failure occurring on the accelerator grid is 11500 hours.
Abstract: English like any other language is rich by means of arbitrary, conventional, symbols which lend it to lot of inconsistencies in spelling, phonology, syntax, and morphology. The research examines the irregularities prevalent in the structure and meaning of some ‘er’ lexical items in English and its implication to vocabulary acquisition. It centers its investigation on the derivational suffix ‘er’, which changes the grammatical category of word. English language poses many challenges to Second Language Learners because of its irregularities, exceptions, and rules. One of the meaning of –er derivational suffix is someone or somebody who does something. This rule often confuses the learners when they meet with the exceptions in normal discourse. The need to investigate instances of such inconsistencies in the formation of –er words and the meanings given to such words by the students motivated this study. For this purpose, some senior secondary two (SS2) students in six randomly selected schools in the metropolis were provided a large number of alphabetically selected ‘er’ suffix ending words, The researcher opts for a test technique, which requires them to provide the meaning of the selected words with- er. The marking of the test was scored on the scale of 1-0, where correct formation of –er word and meaning is scored one while wrong formation and meaning is scored zero. The number of wrong and correct formations of –er words meaning were calculated using percentage. The result of this research shows that a large number of students made wrong generalization of the meaning of the selected -er ending words. This shows how enormous the inconsistencies are in English language and how are affect the learning of English. Findings from the study revealed that though students mastered the basic morphological rules but the errors are generally committed on those vocabulary items that are not frequently in use. The study arrives at this conclusion from the survey of their textbook and their spoken activities. Therefore, the researcher recommends that there should be effective reappraisal of language teaching through implementation of the designed curriculum to reflect on modern strategies of teaching language, identification, and incorporation of the exceptions in rigorous communicative activities in language teaching, language course books and tutorials, training and retraining of teachers on the strategies that conform to the new pedagogy.
Abstract: By using a fixed point theorem of a sum operator, the
existence and uniqueness of positive solution for a class of
boundary value problem of nonlinear fractional differential equation
is studied. An iterative scheme is constructed to approximate it.
Finally, an example is given to illustrate the main result.
Abstract: Small-size and low-power sensors with sensing, signal
processing and wireless communication capabilities is suitable for the
wireless sensor networks. Due to the limited resources and battery
constraints, complex routing algorithms used for the ad-hoc networks
cannot be employed in sensor networks. In this paper, we propose
node-disjoint multi-path hexagon-based routing algorithms in wireless
sensor networks. We suggest the details of the algorithm and compare
it with other works. Simulation results show that the proposed scheme
achieves better performance in terms of efficiency and message
delivery ratio.
Abstract: A Friction stir welding tool is a critical component to
the success of the process. The tool typically consists of a rotating
round shoulder and a threaded cylindrical pin that heats the work
piece, mostly by friction, and moves the softened alloy around it to
form the joint. In this research work, an attempt has been made to
investigate the relationship between FSW variables mainly tool
profile, rotating speed, welding speed and the mechanical properties
(tensile strength, yield strength, percentage elongation, and micro
hardness) of friction stir welded aluminum alloy 5083 joints. From
the experimental details, it can be assessed that the joint produced by
using Triflute profile tool has contribute superior mechanical and
structural properties as compared to Tapered unthreaded & Threaded
tool for 1000rpm.
Abstract: In this paper, a prototype PEM fuel cell vehicle
integrated with a 1 kW air-blowing proton exchange membrane fuel
cell (PEMFC) stack as a main power sources has been developed for
a lightweight cruising vehicle. The test vehicle is equipped with a
PEM fuel cell system that provides electric power to a brushed DC
motor. This vehicle was designed to compete with industrial
lightweight vehicle with the target of consuming least amount of
energy and high performance. Individual variations in driving style
have a significant impact on vehicle energy efficiency and it is well
established from the literature. The primary aim of this study was to
assesses the power and fuel consumption of a hydrogen fuel cell
vehicle operating at three difference driving technique (i.e. 25 km/h
constant speed, 22-28 km/h speed range, 20-30 km/h speed range).
The goal is to develop the best driving strategy to maximize
performance and minimize fuel consumption for the vehicle system.
The relationship between power demand and hydrogen consumption
has also been discussed. All the techniques can be evaluated and
compared on broadly similar terms. Automatic intelligent controller
for driving prototype fuel cell vehicle on different obstacle while
maintaining all systems at maximum efficiency was used. The result
showed that 25 km/h constant speed was identified for optimal
driving with less fuel consumption.