Abstract: In this research, a questionnaire survey was conducted
to measure nap, drowsiness and fatigue of drivers who work for long
shifts, to discuss about the work environment and health conditions for
taxi and bus drivers who work at night-time. The questionnaire sheet
used for this research was organized into the following categories:
tension/tiredness, drowsiness while driving, and the nap situation
during night-time work. The number of taxi drivers was 127 and the
number of bus drivers was 40. Concerning the results of a comparison
of nap hours of taxi and bus drivers, the taxi drivers’ nap hours are
overwhelmingly shorter, and also the frequency of drivers who
experience drowsiness is higher. The burden on bus drivers does not
change because of the system of a two-driver rotation shift. In
particular, the working environment of the taxi driver may lead to
greater fatigue accumulation than the bus driver’s environment.
Abstract: The microstrip antennas area has seen some inventive
work in recent years and is now one of the most dynamic fields of
antenna theory. A novel and simple wideband monopole antenna is
presented printed on a single dielectric substrate which is fed by a 50
ohm microstrip line having a low-profile antenna structure with two
parallel s-shaped meandered line of same size. This antenna is fed by
a coaxial feeding tube. In this research, S–form microstrip patch antenna is designed from
measuring the prototypes of the proposed antenna one available
bands with 10db return loss bandwidths of about GPS application
(GPS L2 1490 MHz) and covering the 1400 to 1580 MHz frequency
band at 1.5 GHz, the simulated results for main parameters such as
return loss, impedance bandwidth, radiation patterns, and gains are
also discussed herein. The modeling study shows that such antennas,
in simplicity design and supply, can satisfy GPS application. Two
parallel slots are incorporated to disturb the surface flow path,
introducing local inductive effect. This antenna is fed by a coaxial
feeding tube.
Abstract: The purpose of this study is to determine the
relationship of anxiety level between male and female undergraduates
at a private university in Malaysia. Convenient sampling method used
in this study in which the students were selected based on the
grouping assigned by the faculty. There were 214 undergraduates
who registered the probability courses had participated in this study.
Mathematics Anxiety Rating Scale (MARS) was the instrument used
in study which used to determine students’ anxiety level towards
probability. Reliability and validity of instrument was done before the
major study was conducted. In the major study, students were given
briefing about the study conducted. Participation of this study was
voluntary. Students were given consent form to determine whether
they agree to participate in the study. Duration of two weeks was
given for students to complete the given online questionnaire. The
data collected will be analyzed using Statistical Package for the
Social Sciences (SPSS) to determine the level of anxiety. There were
three anxiety level, i.e., low, average and high. Students’ anxiety
level was determined based on their scores obtained compared with
the mean and standard deviation. If the scores obtained were below
mean and standard deviation, the anxiety level was low. If the scores
were at below and above the mean and between one standard
deviation, the anxiety level was average. If the scores were above the
mean and greater than one standard deviation, the anxiety level was
high. Results showed that both of genders were having average
anxiety level. Among low, average and high anxiety level, frequency
of males were found to be higher as compared to females. Hence, the
mean values obtained for males (M = 3.62) was higher than females
(M = 3.42). In order to be significant of anxiety level among the
gender, the p-value should be less than .05. The p-value obtained in
this study was .117. However, this value was greater than .05. Thus,
there was no significant difference of anxiety level among the gender.
In other words, there was no relationship of anxiety level with the
gender.
Abstract: This research aims to identify traditional Mon cuisines
as well as gather and classify traditional cuisines of Mon
communities in Bangkok. The studying of this research is used by
methodology of the quantitative research. Using the questionnaire as
the method in collecting information from sampling totally amount of
450 persons analyzed via frequency, percentage and mean value. The
results showed that a variety of traditional Mon cuisines of Bangkok
could split into 6 categories of meat diet with 54 items and 6
categories of desserts with 19 items.
Abstract: This study utilizes a frequency domain approach over
the period of 1996 to 2013 to examine the causal relationship between
governance and economic growth in ten Asian countries, which have
different levels of democracy; classified as “Free”, “Partly Free”, and
“Not Free” countries. The empirical results show that there is no
Granger causality running from governance to economic growth in
“Not Free” countries and “Partly Free” countries with the exception of
Singapore. As for “Free” countries such as South Korea and Taiwan,
there is a one-way causality running from governance to economic
growth. The findings of this study indicate that policy makers in South
Korea, Taiwan, and Singapore could use governance index to improve
their predictions of the future economic growth.
Abstract: EEG correlates of mathematical and trait anxiety level
were studied in 52 healthy Russian-speakers during execution of
error-recognition tasks with lexical, arithmetic and algebraic
conditions. Event-related spectral perturbations were used as a
measure of brain activity. The ERSP plots revealed alpha/beta
desynchronizations within a 500-3000 ms interval after task onset
and slow-wave synchronization within an interval of 150-350 ms.
Amplitudes of these intervals reflected the accuracy of error
recognition, and were differently associated with the three conditions.
The correlates of anxiety were found in theta (4-8 Hz) and beta2 (16-
20 Hz) frequency bands. In theta band the effects of mathematical
anxiety were stronger expressed in lexical, than in arithmetic and
algebraic condition. The mathematical anxiety effects in theta band
were associated with differences between anterior and posterior
cortical areas, whereas the effects of trait anxiety were associated
with inter-hemispherical differences. In beta1 and beta2 bands effects
of trait and mathematical anxiety were directed oppositely. The trait
anxiety was associated with increase of amplitude of
desynchronization, whereas the mathematical anxiety was associated
with decrease of this amplitude. The effect of mathematical anxiety
in beta2 band was insignificant for lexical condition but was the
strongest in algebraic condition. EEG correlates of anxiety in theta
band could be interpreted as indexes of task emotionality, whereas
the reaction in beta2 band is related to tension of intellectual
resources.
Abstract: This paper presents a state-of-the-art survey of the
operations research models developed for internal audit planning.
Two alternative approaches have been followed in the literature for
audit planning: (1) identifying the optimal audit frequency; and (2)
determining the optimal audit resource allocation. The first approach
identifies the elapsed time between two successive audits, which can
be presented as the optimal number of audits in a given planning
horizon, or the optimal number of transactions after which an audit
should be performed. It also includes the optimal audit schedule. The
second approach determines the optimal allocation of audit frequency
among all auditable units in the firm. In our review, we discuss both
the deterministic and probabilistic models developed for audit
planning. In addition, game theory models are reviewed to find the
optimal auditing strategy based on the interactions between the
auditors and the clients.
Abstract: This paper describes a novel sensor device, a pressure
pulse wave meter, which uses a bidirectional condenser microphone.
The microphone work as a microphone as well as a sensor with high
gain over a wide frequency range; they are also highly reliable and
economic. Currently aging is becoming a serious social issue in Japan causing
increased medical expenses in the country. Hence, it is important for
elderly citizens to check health condition at home, and to care the
health conditions through daily monitoring. Given this circumstances,
we developed a novel pressure pulse wave meter based on a
bidirectional condenser microphone: this device is used as a measuring
instrument of health conditions.
Abstract: Acoustic properties of polymeric liquids are high
sensitive to free gas traces in the form of fine bubbles. Their presence
is typical for such liquids because of chemical reactions, small
wettability of solid boundaries, trapping of air in technological
operations, etc. Liquid temperature influences essentially its
rheological properties, which may have an impact on the bubble
pulsations and sound propagation in the system. The target of the
paper is modeling of the liquid temperature effect on single bubble
dynamics and sound dispersion and attenuation in polymeric solution
with spherical gas bubbles. The basic sources of attenuation (heat
exchange between gas in microbubbles and surrounding liquid,
rheological and acoustic losses) are taken into account. It is supposed
that in the studied temperature range the interface mass transfer has a
minor effect on bubble dynamics. The results of the study indicate
that temperature raise yields enhancement of bubble pulsations and
increase in sound attenuation in the near-resonance range and may
have a strong impact on sound dispersion in the liquid-bubble
mixture at frequencies close to the resonance frequency of bubbles.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: While choosing insulating oil, characteristic features
such as thermal cooling, endurance, efficiency and being
environment-friendly should be considered. Mineral oils are referred
as petroleum-based oil. In this study, vegetable oils investigated as an
alternative insulating liquid to mineral oil. Dissipation factor,
breakdown voltage, relative dielectric constant and resistivity
changes with the frequency and voltage of mineral, rapeseed and nut
oils were measured. Experimental studies were performed according
to ASTM D924 and IEC 60156 standards.
Abstract: An Acoustic Micro-Energy Harvester (AMEH) is
developed to convert wasted acoustical energy into useful electrical
energy. AMEH is mathematically modeled using Lumped Element
Modelling (LEM) and Euler-Bernoulli beam (EBB) modelling. An
experiment is designed to validate the mathematical model and assess
the feasibility of AMEH. Comparison of theoretical and experimental
data on critical parameter value such as Mm, Cms, dm and Ceb showed
the variances are within 1% to 6%, which is reasonably acceptable.
Then, AMEH undergoes bandwidth tuning for performance
optimization. The AMEH successfully produces 0.9V/(m/s^2) and
1.79μW/(m^2/s^4) at 60Hz and 400kΩ resistive load which only
show variances about 7% compared to theoretical data. At 1g and
60Hz resonance frequency, the averaged power output is about
2.2mW which fulfilled a range of wireless sensors and
communication peripherals power requirements. Finally, the design
for AMEH is assessed, validated and deemed as a feasible design.
Abstract: The legality of some countries or agencies’ acts to spy
on personal phone calls of the public became a hot topic to many
social groups’ talks. It is believed that this act is considered an
invasion to someone’s privacy. Such act may be justified if it is
singling out specific cases but to spy without limits is very
unacceptable. This paper discusses the needs for not only a simple
and light weight technique to secure mobile voice calls but also a
technique that is independent from any encryption standard or library.
It then presents and tests one encrypting algorithm that is based of
Frequency scrambling technique to show fair and delay-free process
that can be used to protect phone calls from such spying acts.
Abstract: In this study, three robust predicting methods, namely artificial neural network (ANN), adaptive neuro fuzzy inference system (ANFIS) and support vector machine (SVM) were used for computing the resonant frequency of A-shaped compact microstrip antennas (ACMAs) operating at UHF band. Firstly, the resonant frequencies of 144 ACMAs with various dimensions and electrical parameters were simulated with the help of IE3D™ based on method of moment (MoM). The ANN, ANFIS and SVM models for computing the resonant frequency were then built by considering the simulation data. 124 simulated ACMAs were utilized for training and the remaining 20 ACMAs were used for testing the ANN, ANFIS and SVM models. The performance of the ANN, ANFIS and SVM models are compared in the training and test process. The average percentage errors (APE) regarding the computed resonant frequencies for training of the ANN, ANFIS and SVM were obtained as 0.457%, 0.399% and 0.600%, respectively. The constructed models were then tested and APE values as 0.601% for ANN, 0.744% for ANFIS and 0.623% for SVM were achieved. The results obtained here show that ANN, ANFIS and SVM methods can be successfully applied to compute the resonant frequency of ACMAs, since they are useful and versatile methods that yield accurate results.
Abstract: Obesity and osteoporosis are the two diseases whose
increasing prevalence and high impact on the global morbidity and
mortality, during the two recent decades, have gained a status of
major health threats worldwide. Obesity purports to affect the bone
metabolism through complex mechanisms. Debated data on the
connection between the bone mineral density and fracture prevalence
in the obese patients are widely presented in literature. There is
evidence that the correlation of weight and fracture risk is sitespecific.
This study is aimed at determining the connection between
the bone mineral density (BMD) and trabecular bone score (TBS)
parameters in Ukrainian women suffering from obesity. We
examined 1025 40-89-year-old women, divided them into the groups
according to their body mass index: Group A included 360 women
with obesity whose BMI was ≥30 kg/m2, and Group B – 665 women
with no obesity and BMI of
Abstract: We investigate experimentally and theoretically the
dynamics of a capacitive resonator under mixed frequency excitation
of two AC harmonic signals. The resonator is composed of a proof
mass suspended by two cantilever beams. Experimental
measurements are conducted using a laser Doppler Vibrometer to
reveal the interesting dynamics of the system when subjected to twosource
excitation. A nonlinear single-degree-of-freedom model is
used for the theoretical investigation. The results reveal combination
resonances of additive and subtractive type, which are shown to be
promising to increase the bandwidth of the resonator near primary
resonance frequency. Our results also demonstrate the ability to shift
the combination resonances to much lower or much higher frequency
ranges. We also demonstrate the dynamic pull-in instability under
mixed frequency excitation.
Abstract: Nowadays, the use of renewable energy sources has been increasingly great because of the cost increase and public demand for clean energy sources. One of the fastest growing sources is wind energy. In this paper, Wind Diesel Hybrid System (WDHS) comprising a Diesel Generator (DG), a Wind Turbine Generator (WTG), the Consumer Load, a Battery-based Energy Storage System (BESS), and a Dump Load (DL) is used. Voltage is controlled by Diesel Generator; the frequency is controlled by BESS and DL. The BESS elimination is an efficient way to reduce maintenance cost and increase the dynamic response. Simulation results with graphs for the frequency of Power System, active power, and the battery power are presented for load changes. The controlling parameters are optimized by using Imperialist Competitive Algorithm (ICA). The simulation results for the BESS/no BESS cases are compared. Results show that in no BESS case, the frequency control is more optimal than the BESS case by using ICA.
Abstract: This paper shows the connection between emoticons and politeness in written computer-mediated communication. It studies if there are some differences in the use of emoticon between Czech and English written tweets. The assumptions about the use of emoticons were based on the use of greetings and thanks in real, faceto-face situations. The first assumption, that welcome greeting phrase would be accompanied by positive emoticon, was correct. But for the farewell greeting are both positive and negative emoticons possible. The results show lower frequency of negative emoticons in this context. There were also quite often found both positive and negative emoticon in the same tweet. The expression of gratitude is associated with positive emotions. The results show that emoticons accompany polite phrases of greeting and thanks very often both in Czech and English. The use of emoticons with studied polite phrases shows that emoticons have become an integral part of these phrases.
Abstract: This study was aimed to investigate the machining
stability of a spindle tool with different preloaded amount. To this end,
the vibration tests were conducted on the spindle unit with different
preload to assess the dynamic characteristics and machining stability
of the milling machine. Current results demonstrate that the tool tip
frequency response characteristics and the machining stabilities in X
and Y direction are affected to change due to the different preload of
spindle bearings. As found from the results, a high preloaded spindle
tool shows higher limited cutting depth at mid position, while a spindle
with low preload shows a higher limited depth. This indicates that the
machining stability of a milling machine is affected to vary by the
spindle unit when it was assembled with different bearing preload.
Abstract: This article proposes a new method for application in
communication circuit systems that increase efficiency, PAE, output
power and gain in the circuit. The proposed method is based on a
combination of switching class-E and class-J and has been termed
class-EJ. This method was investigated using both theory and
simulation to confirm ∼72% PAE and output power of >39dBm. The
combination and design of the proposed power amplifier accrues gain
of over 15dB in the 2.9 to 3.5GHz frequency bandwidth. This circuit
was designed using MOSFET and high power transistors. The loadand
source-pull method achieved the best input and output networks
using lumped elements. The proposed technique was investigated for
fundamental and second harmonics having desirable amplitudes for
the output signal.