Abstract: Sweep frequency response analysis has been turning
out a powerful tool for investigation of mechanical as well as
electrical integration of transformers. In this paper various aspect of
practical application of SFRA has been studied. Open circuit and
short circuit measurement were done on different phases of high
voltage and low voltage winding. A case study was presented for the
transformer of rating 31.5 MVA for various frequency ranges. A
clear picture was presented for sub- frequency ranges for HV as well
as LV winding. The main motive of work is to investigate high
voltage short circuit response. The theoretical concept about SFRA
responses is validated with expert system software results.
Abstract: Introduction: Whole-Body Vibration (WBV) uses
high frequency mechanical stimuli generated by a vibration plate and
transmitted through bone, muscle and connective tissues to the whole
body. Research has shown that long-term vibration-plate training
improves neuromuscular facilitation, especially in afferent neural
pathways, responsible for the conduction of vibration and
proprioceptive stimuli, muscle function, balance and proprioception.
Some researchers suggest that the vibration stimulus briefly inhibits
the conduction of afferent signals from proprioceptors and can
interfere with the maintenance of body balance. The aim of this study
was to evaluate the influence of a single set of exercises associated
with whole-body vibration on the joint position sense and body
balance. Material and methods: The study enrolled 55 people aged
19-24 years. These individuals were randomly divided into a test
group (30 persons) and a control group (25 persons). Both groups
performed the same set of exercises on a vibration plate. The
following vibration parameters: frequency of 20Hz and amplitude of
3mm, were used in the test group. The control group performed
exercises on the vibration plate while it was off. All participants were
instructed to perform six dynamic exercises lasting 30 seconds each
with a 60-second period of rest between them. The exercises involved
large muscle groups of the trunk, pelvis and lower limbs.
Measurements were carried out before and immediately after
exercise. Joint position sense (JPS) was measured in the knee joint
for the starting position at 45° in an open kinematic chain. JPS error
was measured using a digital inclinometer. Balance was assessed in a
standing position with both feet on the ground with the eyes open and
closed (each test lasting 30 sec). Balance was assessed using Matscan
with FootMat 7.0 SAM software. The surface of the ellipse of
confidence and front-back as well as right-left swing were measured
to assess balance. Statistical analysis was performed using Statistica
10.0 PL software. Results: There were no significant differences
between the groups, both before and after the exercise (p> 0.05). JPS
did not change in both the test (10.7° vs. 8.4°) and control groups
(9.0° vs. 8.4°). No significant differences were shown in any of the
test parameters during balance tests with the eyes open or closed in
both the test and control groups (p> 0.05). Conclusions: 1.
Deterioration in proprioception or balance was not observed
immediately after the vibration stimulus. This suggests that vibrationinduced
blockage of proprioceptive stimuli conduction can have only
a short-lasting effect that occurs only as long as a vibration stimulus
is present. 2. Short-term use of vibration in treatment does not impair
proprioception and seems to be safe for patients with proprioceptive
impairment. 3. These results need to be supplemented with an
assessment of proprioception during the application of vibration
stimuli. Additionally, the impact of vibration parameters used in the
exercises should be evaluated.
Abstract: In this study, static and dynamic responses of a typical
reinforced concrete solid slab, designed to British Standard (BS 8110:
1997) and under self and live loadings for dance halls are reported.
Linear perturbation analysis using finite element method was
employed for modal, impulse loading and frequency response
analyses of the slab under the aforementioned loading condition.
Results from the static and dynamic analyses, comprising of the slab
fundamental frequencies and mode shapes, dynamic amplification
factor, maximum deflection, stress distributions among other
valuable outcomes are presented and discussed. These were gauged
with the limiting provisions in the design code with a view of
justifying valid optimization objective function for the structure that
can ensure both adequate strength and economical section for large
clear span slabs. This is necessary owing to the continued increase in
cost of erecting building structures and the squeeze on public finance
globally.
Abstract: Radio Frequency Identification (RFID) has become a
key technology in the emerging concept of Internet of Things (IoT).
Naturally, business applications would require the deployment of
various RFID systems developed by different vendors that use
different data formats and structures. This heterogeneity poses a
challenge in developing real-life IoT systems with RFID, as
integration is becoming very complex and challenging. Semantic
integration is a key approach to deal with this challenge. To do so,
ontology for RFID systems need to be developed in order to
annotated semantically RFID systems, and hence, facilitate their
integration. Accordingly, in this paper, we propose ontology for
RFID systems. The proposed ontology can be used to semantically
enrich RFID systems, and hence, improve their usage and reasoning.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: Pure nickel coatings have been successfully
electrodeposited on copper substrates by the pulse plating technique.
The influence of current density, duty cycle and pulse frequency on
the surface morphology, crystal orientation, and microhardness was
determined. It was found that the crystallite size of the deposit
increases with increasing current density and duty cycle. The crystal
orientation progressively changed from a random texture at 1 A/dm2
to (200) texture at 10 A/dm2. Increasing pulse frequency resulted in
increased texture coefficient and peak intensity of (111) reflection.
An increase in duty cycle resulted in considerable increase in texture
coefficient and peak intensity of (311) reflection. Coatings obtained
at high current densities and duty cycle present a mixed morphology
of small and large grains. Maximum microhardness of 193 Hv was
achieved at 4 A/dm2, 10 Hz and duty cycle of 50%. Nickel coatings
with (200) texture are ductile while (111) texture improves the
microhardness of the coatings.
Abstract: Fires is one of the main types of disturbances that
shape ecosystems in the Mediterranean region. However nowadays,
climate alterations towards higher temperatures result on increased
levels of fire intensity, frequency and spread as well as difficulties for
natural regeneration to occur. Thasos Island is one of the Greek
islands that has experienced those problems. Since 1984, a series of
wildfires led to the reduction of forest cover from 61.6% to almost
20%. The negative impacts were devastating in many different
aspects for the island. The absence of plant cover, post-wildfire
precipitation and steep slopes were the major factors that induced
severe soil erosion and intense floods. That also resulted to serious
economic problems to the local communities and the inability of the
burnt areas to regenerate naturally. Despite the substantial amount of
published work regarding Thasos wildfires, there is no information
related to post-wildfire effects on factors such as soil erosion. More
research related to post-fire effects should help to an overall
assessment of the negative impacts of wildfires on land degradation
through processes such as soil erosion and flooding.
Abstract: Hypertension is a common condition causing cardio
and cerebrovascular complications. Portugal has one of the highest
mortality rates from stroke and a high prevalence of hypertension.
Systolic Blood Pressure (SBP) is an important risk factor for
cardiovascular events (myocardial infarction and stroke) and
premature mortality, particularly in the elderly population. The
present study aims to estimate the prevalence of hypertension in a
Portuguese population living in a coastal city and to identify some of
its determinants (namely gender, age, the body mass index and
physical activity frequency). A total of 91 adults who attended three pharmacies of a coastal
city in the center of Portugal, between May and August of 2013 were
evaluated. Attendants who reported to have diabetes or taking
antihypertensive drugs in the 2 previous weeks were excluded from
the study. Sociodemographic factors, BMI, habits of exercise and BP
were assessed. Hypertension was defined as blood pressure ≥140/90
mmHg. The majority of the studied population was constituted by women
(75.8%), with a mean age of 54.2±1.6 years old, married or living in
civil union and that had completed secondary school or had higher
education (40%). They presented a mean BMI of 26.2±4.76 Kg/m2.,
and were sedentary. The mean BP was 127.0±17.77mmHg- 74.69 ±
9.53. In this population we found 4.3% of people with hypertension
and 16.1% with normal high blood pressure. Men exhibit a tendency to present higher systolic blood pressure
values than women. Of all the factors considered, SBP values also
tended to be higher with age and higher BMI values.
Despite the fact that the mean values of SBP did not present values
higher than 140 mmHg we must be concerned because the studied
population is undiagnosed for hypertension. Although this is a preliminary study, it might be a prelude to the
upcoming research about the underlying factors responsible for the
occurrence of SBP.
Abstract: Graphene, a single-atom sheet, has been considered as
the most promising material for making future nanoelectromechanical
systems as well as purely electrical switching with graphene
transistors. Graphene-based devices have advantages in scaled-up
device fabrication due to the recent progress in large area graphene
growth and lithographic patterning of graphene nanostructures. Here
we investigated its mechanical responses of circular graphene
nanoflake under the nanoindentation using classical molecular
dynamics simulations. A correlation between the load and the
indentation depth was constructed. The nanoindented force in this
work was applied to the center point of the circular graphene nanoflake
and then, the resonance frequency could be tuned by a nanoindented
depth. We found the hardening or the softening of the graphene
nanoflake during its nanoindented-deflections, and such properties
were recognized by the shift of the resonance frequency. The
calculated mechanical parameters in the force-vs-deflection plot were
in good agreement with previous experimental and theoretical works.
This proposed schematics can detect the pressure via the deflection
change or/and the resonance frequency shift, and also have great
potential for versatile applications in nanoelectromechanical systems.
Abstract: The growth in the demand of electrical energy is
leading to load on the Power system which increases the occurrence
of frequent oscillations in the system. The reason for the oscillations
is due to the lack of damping torque which is required to dominate
the disturbances of Power system. By using FACT devices, such as
Unified Power Flow Controller (UPFC) can control power flow,
reduce sub-synchronous resonances and increase transient stability.
Hence, UPFC is used to damp the oscillations occurred in Power
system. This research focuses on adapting the neuro fuzzy controller
for the UPFC design by connecting the infinite bus (SMIB - Single
machine Infinite Bus) to a linearized model of synchronous machine
(Heffron-Phillips) in the power system. This model gains the
capability to improve the transient stability and to damp the
oscillations of the system.
Abstract: In this paper, a comparative performance analysis of
mostly used four nonlinearity cancellation techniques used to realize
the passive resistor by MOS transistors, is presented. The comparison
is done by using an integrator circuit which is employing sequentially
Op-amp, OTRA and ICCII as active element. All of the circuits are
implemented by MOS-C realization and simulated by PSPICE
program using 0.35μm process TSMC MOSIS model parameters.
With MOS-C realization, the circuits became electronically tunable
and fully integrable which is very important in IC design. The output
waveforms, frequency responses, THD analysis results and features
of the nonlinearity cancellation techniques are also given.
Abstract: Spectrum handover is a significant topic in the
cognitive radio networks to assure an efficient data transmission in
the cognitive radio user’s communications. This paper proposes a
comparison between three spectrum handover models: VIKOR, SAW
and MEW. Four evaluation metrics are used. These metrics are,
accumulative average of failed handover, accumulative average of
handover performed, accumulative average of transmission
bandwidth and, accumulative average of the transmission delay. As a difference with related work, the performance of the three
spectrum handover models was validated with captured data of
spectrum occupancy in experiments performed at the GSM frequency
band (824 MHz - 849 MHz). These data represent the actual behavior
of the licensed users for this wireless frequency band. The results of the comparison show that VIKOR Algorithm
provides a 15.8% performance improvement compared to SAW
Algorithm and, it is 12.1% better than the MEW Algorithm.
Abstract: This paper develops a multiple channel assignment
model, which allows to take advantage of spectrum opportunities in
cognitive radio networks in the most efficient way. The developed
scheme allows making several assignments of available and
frequency adjacent channel, which require a bigger bandwidth, under
an equality environment. The hybrid assignment model it is made by
two algorithms, one that makes the ranking and selects available
frequency channels and the other one in charge of establishing the
Max-Min Fairness for not restrict the spectrum opportunities for all
the other secondary users, who also claim to make transmissions.
Measurements made were done for average bandwidth, average
delay, as well as fairness computation for several channel
assignments. Reached results were evaluated with experimental
spectrum occupational data from captured GSM frequency band. The
developed model shows evidence of improvement in spectrum
opportunity use and a wider average transmission bandwidth for each
secondary user, maintaining equality criteria in channel assignment.
Abstract: The aim of this study is to identify the suitability of
Virtual Learning Environment (VLE) in welding simulator
application towards Computer-Based Training (CBT) in developing
skills upon new students at the Advanced Technology Training
Center (ADTEC) Batu Pahat, Johor, Malaysia and GIATMARA,
Batu Pahat, Johor, Malaysia. The significance of the study is to create
a computer-based skills development approach in welding technology
among new students in ADTEC and GIATMARA as well as to
cultivate the elements of general skills among them. This study is
also important in elevating the number of individual knowledge
workers (K-workers) working in manufacturing industry in order to
achieve a national vision which is to be an industrial nation in the
year of 2020. The design of the study is a survey type of research
which using questionnaires as the instruments and some 136 students
from ADTEC and GIATMARA were interviewed. Descriptive
analysis is used to identify the frequency and mean values. The
findings of the study show that the welding technology has developed
skills in the students because of the application of VLE simulated at a
high level and the respondents agreed that the skills could be
embedded through the application of the VLE simulator. In summary,
the VLE simulator is suitable in welding skills development training
in terms of exposing new students with the relevant characteristics of
welding skills and at the same time spurring the students’ interest
towards learning more about the skills.
Abstract: This study, tries to suggest a design method based on
displacement using finite difference numerical modeling in
reinforcing soil retaining wall with steel strip. In this case, dynamic
loading characteristics such as duration, frequency, peak ground
acceleration, geometrical characteristics of reinforced soil structure
and type of the site are considered to correct the pseudo static method
and finally introduce the pseudo static coefficient as a function of
seismic performance level and peak ground acceleration. For this
purpose, the influence of dynamic loading characteristics,
reinforcement length, height of reinforced system and type of the site
are investigated on seismic behavior of reinforcing soil retaining wall
with steel strip. Numerical results illustrate that the seismic response
of this type of wall is highly dependent to cumulative absolute
velocity, maximum acceleration, and height and reinforcement length
so that the reinforcement length can be introduced as the main factor
in shape of failure. Considering the loading parameters, geometric parameters of the
wall and type of the site showed that the used method in this study
leads to efficient designs in comparison with other methods, which
are usually based on limit-equilibrium concept. The outputs show the
over-estimation of equilibrium design methods in comparison with
proposed displacement based methods here.
Abstract: This article presents the main results of a numerical
investigation on the uncertainty of dynamic response of structures
with statistically correlated random damping Gamma distributed. A
computational method based on a Linear Statistical Model (LSM) is
implemented to predict second order statistics for the response of a
typical industrial building structure. The significance of random
damping with correlated parameters and its implications on the
sensitivity of structural peak response in the neighborhood of a
resonant frequency are discussed in light of considerable ranges of
damping uncertainties and correlation coefficients. The results are
compared to those generated using Monte Carlo simulation
techniques. The numerical results obtained show the importance of
damping uncertainty and statistical correlation of damping
coefficients when obtaining accurate probabilistic estimates of
dynamic response of structures. Furthermore, the effectiveness of the
LSM model to efficiently predict uncertainty propagation for
structural dynamic problems with correlated damping parameters is
demonstrated.
Abstract: Dead wood and habitat tree such as fallen logs, snags,
stumps and cracks and loos bark etc. are regarded as an important
ecological component of forests on which many forest dwelling
species depend on presence of them within forest ecosystems.
Meanwhile its relation to management history in Caspian forest has
gone unreported. The aim of research was to compare the amounts of
dead wood and habitat trees in the forests with historically different
intensities of management, including: forests with the long term
implication of management (PS), the short term implication of
management (NS) which were compared with semi virgin forest
(GS). The number of 405 individual dead and habitat trees were
recorded and measured at 109 sampling locations. ANOVA revealed
volume of dead tree in the form and decay classes significantly differ
within sites and dead volume in the semi virgin forest significantly
higher than managed sites. Comparing the amount of dead and
habitat tree in three sites showed that, dead tree volume related with
management history and significantly differ in three study sites.
Meanwhile, frequency of habitat trees was significantly different
within sites. The highest amount of habitat trees including cavities,
cracks and loose bark and fork split trees was recorded in virgin site
and lowest recorded in the sites with the long term implication of
management. It can be concluded that forest management cause
reduction of the amount of dead and habitat tree specially in a large
size, thus managing this forest according to ecological sustainable
principles require a commitment to maintaining stand structure that
allow, continued generation of dead trees in a full range of size.
Abstract: Objectives: To determine the nutritional status and
risk factors associated with women practicing geophagia in QwaQwa,
South Africa. Materials and Methods: An observational epidemiological study
design was adopted which included an exposed (geophagia) and nonexposed
(control) group. A food frequency questionnaire, anthropometric measurements and blood sampling were applied to
determine nutritional status of participants. Logistic regression
analysis was performed in order to identify factors that were likely to
be associated with the practice of geophagia. Results: The mean total energy intake for the geophagia group (G)
and control group (C) were 10324.31 ± 2755.00 kJ and 10763.94 ±
2556.30 kJ respectively. Both groups fell within the overweight
category according to the mean Body Mass Index (BMI) of each
group (G= 25.59 kg/m2; C= 25.14 kg/m2). The mean serum iron
levels of the geophagia group (6.929 μmol/l) were significantly lower
than that of the control group (13.75 μmol/l) (p = 0.000). Serum
transferrin (G=3.23g/l; C=2.7054g/l) and serum transferrin saturation
(G=8.05%; C=18.74%) levels also differed significantly between
groups (p=0.00). Factors that were associated with the practice of
geophagia included haemoglobin (Odds ratio (OR):14.50), serumiron
(OR: 9.80), serum-ferritin (OR: 3.75), serum-transferrin (OR:
6.92) and transferrin saturation (OR: 14.50). A significant negative
association (p=0.014) was found between women who were wageearners
and those who were not wage-earners and the practice of
geophagia (OR: 0.143; CI: 0.027; 0.755). These findings seem to
indicate that a permanent income may decrease the likelihood of
practising geophagia. Key Findings: Geophagia was confirmed to be a risk factor for
iron deficiency in this community. The significantly strong
association between geophagia and iron deficiency emphasizes the
importance of identifying the practice of geophagia in women,
especially during their child bearing years.
Abstract: Current study established for EEG signal analysis in
patients with language disorder. Language disorder can be defined as
meaningful delay in the use or understanding of spoken or written
language. The disorder can include the content or meaning of
language, its form, or its use. Here we applied Z-score, power
spectrum, and coherence methods to discriminate the language
disorder data from healthy ones. Power spectrum of each channel in
alpha, beta, gamma, delta, and theta frequency bands was measured.
In addition, intra hemispheric Z-score obtained by scoring algorithm.
Obtained results showed high Z-score and power spectrum in
posterior regions. Therefore, we can conclude that peoples with
language disorder have high brain activity in frontal region of brain
in comparison with healthy peoples. Results showed that high coherence correlates with irregularities
in the ERP and is often found during complex task, whereas low
coherence is often found in pathological conditions. The results of the
Z-score analysis of the brain dynamics showed higher Z-score peak
frequency in delta, theta and beta sub bands of Language Disorder
patients. In this analysis there were activity signs in both hemispheres
and the left-dominant hemisphere was more active than the right.
Abstract: The Radio Frequency Identification (RFID) technology
has a diverse base of applications, but it is also prone to security
threats. There are different types of security attacks which limit the
range of the RFID applications. For example, deploying the RFID
networks in insecure environments could make the RFID system
vulnerable to many types of attacks such as spoofing attack, location
traceability attack, physical attack and many more. Therefore, security
is often an important requirement for RFID systems. In this paper,
RFID mutual authentication protocol is implemented based on mobile
agent technology and timestamp, which are used to provide strong
authentication and integrity assurances to both the RFID readers and
their corresponding RFID tags. The integration of mobile agent
technology and timestamp provides promising results towards
achieving this goal and towards reducing the security threats in RFID
systems.