Abstract: This paper presents the Finite Element Method (FEM) for analyzing the failure pattern of rectangular slab with various edge conditions. Non-Linear static analysis is carried out using ANSYS 15 Software. Using SOLID65 solid elements, the compressive crushing of concrete is facilitated using plasticity algorithm, while the concrete cracking in tension zone is accommodated by the nonlinear material model. Smeared reinforcement is used and introduced as a percentage of steel embedded in concrete slab. The behavior of the analyzed concrete slab has been observed in terms of the crack pattern and displacement for various loading and boundary conditions. The finite element results are also compared with the experimental data. One of the other objectives of the present study is to show how similar the crack path found by ANSYS program to those observed for the yield line analysis. The smeared reinforcement method is found to be more practical especially for the layered elements like concrete slabs. The value of this method is that it does not require explicit modeling of the rebar, and thus a much coarser mesh can be defined.
Abstract: Strength and deformability characteristics of a liquefiable sand deposit including the development of earthquake-induced shear stress and shear strain as well as soil softening via the progressive degradation of shear modulus were studied via shaking table experiments. To do so, a model of a liquefiable sand deposit was constructed and densely instrumented where accelerations, pressures, and displacements at different locations were continuously monitored. Furthermore, the confinement effects on the strength and deformation characteristics of the liquefiable sand deposit due to an external surcharge by placing a heavy concrete slab (i.e. the model of an actual structural rigid pavement) on the ground surface were examined. The results indicate that as the number of seismic-loading cycles increases, the sand deposit softens progressively as large shear strains take place in different sand elements. Liquefaction state is reached after the combined effects of the progressive degradation of the initial shear modulus associated with the continuous decrease in the mean principal stress, and the buildup of the excess of pore pressure takes place in the sand deposit. Finally, the confinement effects given by a concrete slab placed on the surface of the sand deposit resulted in a favorable increasing in the initial shear modulus, an increase in the mean principal stress and a decrease in the softening rate (i.e. the decreasing rate in shear modulus) of the sand, thus making the onset of liquefaction to take place at a later stage. This is, only after the sand deposit having a concrete slab experienced a higher number of seismic loading cycles liquefaction took place, in contrast to an ordinary sand deposit having no concrete slab.
Abstract: In this paper, we investigate theoretically the waves propagation in a lossless double-negative grounded slab (DNG). This study is performed by the Transverse Resonance Method (TRM). The proper or improper nature of real and complex modes is observed. They are highly dependent on metamaterial parameters, i.e. ɛr-negative, µr-negative, or both. Numerical results provided that only the proper complex modes (i.e., leaky modes) exist in DNG slab, and only the improper complex modes exist in single-negative grounded slab.
Abstract: In this study, static and dynamic responses of a typical
reinforced concrete solid slab, designed to British Standard (BS 8110:
1997) and under self and live loadings for dance halls are reported.
Linear perturbation analysis using finite element method was
employed for modal, impulse loading and frequency response
analyses of the slab under the aforementioned loading condition.
Results from the static and dynamic analyses, comprising of the slab
fundamental frequencies and mode shapes, dynamic amplification
factor, maximum deflection, stress distributions among other
valuable outcomes are presented and discussed. These were gauged
with the limiting provisions in the design code with a view of
justifying valid optimization objective function for the structure that
can ensure both adequate strength and economical section for large
clear span slabs. This is necessary owing to the continued increase in
cost of erecting building structures and the squeeze on public finance
globally.
Abstract: Damages from noise and vibration are increasing
every year, most of which are noises between floors in deteriorated
building caused by floor impact sound. In this study, the concrete slab
measured vibration impact sound for evaluation floor vibration of
deteriorated buildings that fails to satisfy with the minimum thickness.
In this experimental study, the vibration scale by impact sound was
calibrated and compared with ISO and AIJ standard for vibration. The
results show that vibration in slab with thickness used in existing
building reach human perception levels.
Abstract: The modern energy-efficient houses are often founded on a thermal insulation (TI) layer placed under the building’s RC foundation slab.The purpose of the paper is to identify the potential problems of the buildings founded on TI layer from the seismic point of view. The two main goals of the study were to assess the seismic behavior of such buildings, and to search for the critical structural parameters affecting the response of the superstructure as well as of the extruded polystyrene (XPS) layer. As a test building a multi-storeyed RC frame structure with and without the XPS layer under the foundation slab has been investigated utilizing nonlinear dynamic (time-history) and static (pushover) analyses. The structural response has been investigated with reference to the following performance parameters: i) Building’s lateral roof displacements, ii) Edge compressive and shear strains of the XPS, iii) Horizontal accelerations of the superstructure, iv) Plastic hinge patterns of the superstructure, v) Part of the foundation in compression, and vi) Deformations of the underlying soil and vertical displacements of the foundation slab (i.e. identifying the potential uplift). The results have shown that in the case of higher and stiff structures lying on firm soil the use of XPS under the foundation slab might induce amplified structural peak responses compared to the building models without XPS under the foundation slab. The analysis has revealed that the superstructure as well as the XPS response is substantially affected by the stiffness of the foundation slab.
Abstract: A mathematical heat transfer model for the prediction of transient heating of the slab in a direct-fired walking beam type reheating furnace has been developed by considering the nongray thermal radiation with given furnace environments. The furnace is modeled as radiating nongray medium with carbon dioxide and water with five-zoned gas temperature and the furnace wall is considered as a constant temperature lower than furnace gas one. The slabs are moving with constant velocity depending on the residence time through the non-firing, charging, preheating, heating, and final soaking zones. Radiative heat flux obtained by considering the radiative heat exchange inside the furnace as well as convective one from the surrounding hot gases are introduced as boundary condition of the transient heat conduction within the slab. After validating thermal radiation model adopted in this work, thermal fields in both model and real reheating furnace are investigated in terms of radiative heat flux in the furnace and temperature inside the slab. The results show that the slab in the furnace can be more heated with higher slab emissivity and residence time.
Abstract: The tremendous loss of life that resulted in the aftermath of recent earthquakes in developing countries is mostly due to the collapse of non-engineered and semi-engineered building structures. Such structures are used as houses, schools, primary healthcare centers and government offices. These building are classified structurally into two categories viz. non-engineered and semi-engineered. Non-engineered structures include: adobe, unreinforced masonry (URM) and wood buildings. Semi-engineered buildings are mostly low-rise (up to 3 story) light concrete frame structures or masonry bearing walls with reinforced concrete slab. This paper presents an overview of the typical damage observed in non-engineered structures and their most likely causes in the past earthquakes with specific emphasis on the performance of such structures in the 2005 Kashmir earthquake. It is demonstrated that seismic performance of these structures can be improved from life-safety viewpoint by adopting simple low-cost modifications to the existing construction practices. Incorporation of some of these practices in the reconstruction efforts after the 2005 Kashmir earthquake are examined in the last section for mitigating seismic risk hazard.
Abstract: To calculate the temperature distribution of the slab in
a hot rolled reheating furnace a mathematical model has been
developed by considering the thermal radiation in the furnace and
transient conduction in the slab. The furnace is modeled as radiating
medium with spatially varying temperature. Radiative heat flux within
the furnace including the effect of furnace walls, combustion gases,
skid beams and buttons is calculated using the FVM and is applied as
the boundary condition of the transient conduction equation of the
slab. After determining the slab emissivity by comparison between
simulation and experimental work, variation of heating characteristics
in the slab is investigated in the case of changing furnace temperature
with various time and the slab residence time is optimized with this
evaluation.
Abstract: In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoff's hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a slab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. On these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degree s of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.
Abstract: We derive simple sets of equations to describe the microwave response of a thin film of magnetized hydrogen plasma in the presence of carbon nanotubes, which were grown by ironcatalyzed high-pressure disproportionation (HiPco). By considering the interference effects due to multiple reflections between thin plasma film interfaces, we present the effects of the continuously changing external magnetic field and plasma parameters on the reflected power, absorbed power, and transmitted power in the system. The simulation results show that the interference effects play an important role in the reflectance, transmittance and absorptance of microwave radiation at the magnetized plasma slab. As a consequence, the interference effects lead to a sinusoidal variation of the reflected intensity and can greatly reduce the amount of reflection power, but the absorption power increases.
Abstract: A theoretical study of the rigidities of slabs with
circular voids oriented in the longitudinal and in the transverse
direction is discussed. Equations are presented for predicting the
bending and torsional rigidities of the voided slabs. This paper
summarizes the results of an extensive literature search and initial
review of the current methods of analyzing voided slab. The various
methods of calculating the equivalent plate parameters, which are
necessary for two-dimensional analysis, are also reviewed. Static
deflections on voided slabs are shown to be in good agreement with
proposed equation.
Abstract: Reinforced concrete stair slabs with mid landings i.e.
Dog-legged shaped are conventionally designed as per specifications
of standard codes of practices which guide about the effective span
according to the varying support conditions. Presently, the behavior
of such slabs has been investigated using Finite Element method. A
single flight stair slab with landings on both sides and supported at
ends on wall, and a multi flight stair slab with landings and six
different support arrangements have been analyzed. The results
obtained for stresses, strains and deflections are used to describe the
behavior of such stair slabs, including locations of critical moments
and deflections. Values of critical moments obtained by F.E. analysis
have also have been compared with that obtained from conventional
analysis. Analytical results show that the moments are also critical
near the kinks i.e. junction of mid-landing and inclined waist slab.
This change in the behavior of dog-legged stair slab may be due to
continuity of the material in transverse direction in two landings
adjoining the waist slab, hence additional stiffness achieved. This
change in the behavior is generally not taken care of in conventional
method of design.