Abstract: This paper presents the variation of the dynamic
characteristics of a spindle with the change of bearing preload. The
correlations between the variation of bearing preload and fundamental
modal parameters were first examined by conducting vibration tests on
physical spindle units. Experimental measurements show that the
dynamic compliance and damping ratio associated with the
dominating modes were affected to vary with variation of the bearing
preload. When the bearing preload was slightly deviated from a
standard value, the modal frequency and damping ability also vary to
different extent, which further enable the spindle to perform with
different compliance. For the spindle used in this study, a standard
preload value set on bearings would enable the spindle to behave a
higher stiffness as compared with others with a preload variation. This
characteristic can be served as a reference to examine the variation of
bearing preload of spindle in assemblage or operation.
Abstract: We used high-precision Global Positioning System
(GPS) to geodetically constrain the motion of stations in the
Darjiling-Sikkim Himalayan (DSH) wedge and examine the
deformation at the Indian-Tibetan plate boundary using IGS
(International GPS Service) fiducial stations. High-precision GPS
based displacement and velocity field was measured in the DSH
between 1997 and 2009. To obtain additional insight north of the
Indo-Tibetan border and in the Darjiling-Sikkim-Tibet (DaSiT)
wedge, published velocities from four stations J037, XIGA, J029 and
YADO were also included in the analysis. India-fixed velocities or
the back-slip was computed relative to the pole of rotation of the
Indian Plate (Latitude 52.97 ± 0.22º, Longitude - 0.30 ± 3.76º, and
Angular Velocity 0.500 ± 0.008º/ Myr) in the DaSiT wedge.
Dislocation modelling was carried out with the back-slip to model the
best possible solution of a finite rectangular dislocation or the
causative fault based on dislocation theory that produced the
observed back-slip using a forward modelling approach. To find the
best possible solution, three different models were attempted. First,
slip along a single thrust fault, then two thrust faults and in finally,
three thrust faults were modelled to simulate the back-slip in the
DaSiT wedge. The three-fault case bests the measured displacements
and is taken as the best possible solution.
Abstract: Analysis of real life problems often results in linear
systems of equations for which solutions are sought. The method to
employ depends, to some extent, on the properties of the coefficient
matrix. It is not always feasible to solve linear systems of equations
by direct methods, as such the need to use an iterative method
becomes imperative. Before an iterative method can be employed
to solve a linear system of equations there must be a guaranty that
the process of solution will converge. This guaranty, which must
be determined apriori, involve the use of some criterion expressible
in terms of the entries of the coefficient matrix. It is, therefore,
logical that the convergence criterion should depend implicitly on the
algebraic structure of such a method. However, in deference to this
view is the practice of conducting convergence analysis for Gauss-
Seidel iteration on a criterion formulated based on the algebraic
structure of Jacobi iteration. To remedy this anomaly, the Gauss-
Seidel iteration was studied for its algebraic structure and contrary
to the usual assumption, it was discovered that some property of the
iteration matrix of Gauss-Seidel method is only diagonally dominant
in its first row while the other rows do not satisfy diagonal dominance.
With the aid of this structure we herein fashion out an improved
version of Gauss-Seidel iteration with the prospect of enhancing
convergence and robustness of the method. A numerical section is
included to demonstrate the validity of the theoretical results obtained
for the improved Gauss-Seidel method.
Abstract: Lead (Pb) poisoning is one of the most common and
preventable environmental health problems. There are different
sources of environmental pollution with lead as lead alkyl additives
in petrol and manufacturing processes. Pb in the atmosphere can be
deposited in urban soils, and may then be re-suspended to re-enter the
atmosphere. This could increase human exposure to Pb and cause
long-term health effects. Thus, monitoring Pb pollution is considered
one of the major tasks in controlling pollution. Scalp hair can be
utilized for the determination of lead (Pb) concentration. It provides a
lasting record of metal intakes of weeks or even months, and for most
metals, their accumulation in hair reflects their accumulation in the
whole body. This work was conducted to investigate the
concentration of lead in male scalp hair of Cairo (residential-traffic
and residential-industrial) and rural residents after twenty years of
phasing out of leaded gasoline. Results indicated that the mean
concentration of lead in hair of residential-traffic (9.7552 μg/g ±0.71)
and residential-industrial (12.3288 μg/g ±1.13) was significantly
higher than that in rural residents (4.7327 μg/g ±0.67). The mean
concentration of lead in hair of resident’s industrial areas was the
highest among Cairo residents and not the traffic areas as it was
before phasing out of leaded gasoline. Twenty years of phasing out of
leaded gasoline in Cairo has greatly improved the lead pollution
among residents of traffic areas, but industrial areas residents were
still suffering from lead pollution, which needs more efforts to
control the sources of lead pollution.
Abstract: It is known that residual welding deformations give
negative effect to processability and operational quality of welded
structures, complicating their assembly and reducing strength.
Therefore, selection of optimal technology, ensuring minimum
welding deformations, is one of the main goals in developing a
technology for manufacturing of welded structures.
Through years, JSC SSTC has been developing a theory for
estimation of welding deformations and practical activities for
reducing and compensating such deformations during welding
process. During long time a methodology was used, based on analytic
dependence. This methodology allowed defining volumetric changes
of metal due to welding heating and subsequent cooling. However,
dependences for definition of structures deformations, arising as a
result of volumetric changes of metal in the weld area, allowed
performing calculations only for simple structures, such as units, flat
sections and sections with small curvature. In case of complex 3D
structures, estimations on the base of analytic dependences gave
significant errors.
To eliminate this shortage, it was suggested to use finite elements
method for resolving of deformation problem. Here, one shall first
calculate volumes of longitudinal and transversal shortenings of
welding joints using method of analytic dependences and further,
with obtained shortenings, calculate forces, which action is
equivalent to the action of active welding stresses. Further, a finiteelements
model of the structure is developed and equivalent forces
are added to this model. Having results of calculations, an optimal
sequence of assembly and welding is selected and special measures to
reduce and compensate welding deformations are developed and
taken.
Abstract: This study aims to examine the role of career
advancement and job security as predictors of employee commitment
to their organization. Data was collected from 580 frontline
employees attached to two departments of 29 luxury hotels in
Peninsular Malaysia. Statistical results using Partial Least Squares
technique provided support for the proposed hypotheses. In view of
the findings, theoretical and practical implications are discussed.
Abstract: This paper proposes a cooperative Alamouti space time
transmission scheme with low relay complexity for the cooperative
communication systems. In the proposed scheme, the source node
combines the data symbols to construct the Alamouti-coded form at
the destination node, while the conventional scheme performs the
corresponding operations at the relay nodes. In simulation results,
it is shown that the proposed scheme achieves the second order
cooperative diversity while maintaining the same bit error rate (BER)
performance as that of the conventional scheme.
Abstract: Enzyme activity was evaluated in the intestine of
juvenile dourado (Salminus brasiliensis) fed with diets containing 0,
10 or 20% of lyophilized bovine colostrum (LBC) inclusion for either
30 or 60 days. The intestinal enzymes acid and alkaline phosphatase
(ACP and ALP, respectively), non-specific esterase (NSE), lipase
(LIP), dipeptidyl aminopeptidase IV (DAP IV) and leucine
aminopeptidase (LAP) were studied using histochemistry in four
intestinal segments (S1, S2, S3 and posterior intestine). Weak
proteolitic activity was observed in all intestinal segments for DAP
IV and LAP. The activity of NSE and LIP was also weak in all
intestines, except for the moderate activity of NSE in the S2 of 20%
LBC group after 30 days and in the S1 of 0% LBC group after 60
days. The ACP was detected only in the S2 and S3 of the 10% LBC
group after 30 days. Moderate and strong staining was observed in
the first three intestinal segments for ALP and weak activity in the
posterior intestine. The activity of DAP IV, LAP and ALP were also
present in the cytoplasm of the enterocytes. In the present results,
bovine colostrum feeding did not cause alterations in activity of
intestinal enzymes.
Abstract: Electronic market place plays an important
intermediary role for connecting dealers and retail customers. The
main aim of this paper is to design a value co-creation model in
used-car auctions. More specifically, the study has been designed in
order to describe the process of value co-creation in used-car auctions,
to explore the co-created values in used-car auctions, and finally
conclude the paper indicating the future research directions. Our
analysis shows that economic values as well as non-economic values
are co-created in used-car auctions. In addition, this paper contributes
to the academic society broadening the view of value co-creation in
service science.
Abstract: This paper presents the application of finite dynamic
programming, specifically the "Markov Chain" model, as part of the
decision making process of a company in the cosmetics sector located
in the vicinity of Bogota DC. The objective of this process was to
decide whether the company should completely reconstruct its
wastewater treatment plant or instead optimize the plant through the
addition of equipment. The goal of both of these options was to make
the required improvements in order to comply with parameters
established by national legislation regarding the treatment of waste
before it is released into the environment. This technique will allow
the company to select the best option and implement a solution for
the processing of waste to minimize environmental damage and the
acquisition and implementation costs.
Abstract: Because of high thermal efficiency and low CO2
emission, diesel engines are being used widely in many industrial
fields although it makes many PM and NOx which give both human
health and environment a negative effect. NOx regulations for diesel
engines, however, are being strengthened and it is impossible to meet
the emission standard without NOx reduction devices such as SCR
(Selective Catalytic Reduction), LNC (Lean NOx Catalyst), and LNT
(Lean NOx Trap). Among the NOx reduction devices, urea-SCR
system is known as the most stable and efficient method to solve the
problem of NOx emission. But this device has some issues associated
with the ammonia slip phenomenon which is occurred by shortage of
evaporation and thermolysis time, and that makes it difficult to achieve
uniform distribution of the injected urea in front of monolith.
Therefore, this study has focused on the mixing enhancement between
urea and exhaust gases to enhance the efficiency of the SCR catalyst
equipped in catalytic muffler by changing inlet gas temperature and
spray conditions to improve the spray uniformity of the urea water
solution. Finally, it can be found that various parameters such as inlet
gas temperature and injector and injection angles significantly affect
the evaporation and mixing of the urea water solution with exhaust
gases, and therefore, optimization of these parameters are required.
Abstract: Second line antiretroviral therapy (ART) regimen is
used when patients fail their first line regimen. There are many
factors such as non-adherence, drug resistance as well as virological
and immunological failure that lead to second line highly active
antiretroviral therapy (HAART) regimen treatment failure. This study
was aimed at determining predictor factors to treatment failure with
second line HAART and analyzing median survival time.
An observational, retrospective study was conducted in Sungai
Buloh Hospital (HSB) to assess current status of HIV patients treated
with second line HAART regimen. Convenience sampling was used
and 104 patients were included based on the study’s inclusion and
exclusion criteria. Data was collected for six months i.e. from July
until December 2013. Data was then analysed using SPSS version 18.
Kaplan-Meier and Cox regression analyses were used to measure
median survival times and predictor factors for treatment failure.
The study population consisted mainly of male subjects, aged 30-
45 years, who were heterosexual, and had HIV infection for less than
6 years. The most common second line HAART regimen given was
lopinavir/ritonavir (LPV/r)-based combination. Kaplan-Meier
analysis showed that patients on LPV/r demonstrated longer median
survival times than patients on indinavir/ritonavir (IDV/r) based
combination (p
Abstract: Artificial Neural Networks (ANN) trained using backpropagation
(BP) algorithm are commonly used for modeling
material behavior associated with non-linear, complex or unknown
interactions among the material constituents. Despite multidisciplinary
applications of back-propagation neural networks
(BPNN), the BP algorithm possesses the inherent drawback of
getting trapped in local minima and slowly converging to a global
optimum. The paper present a hybrid artificial neural networks and
genetic algorithm approach for modeling slump of ready mix
concrete based on its design mix constituents. Genetic algorithms
(GA) global search is employed for evolving the initial weights and
biases for training of neural networks, which are further fine tuned
using the BP algorithm. The study showed that, hybrid ANN-GA
model provided consistent predictions in comparison to commonly
used BPNN model. In comparison to BPNN model, the hybrid ANNGA
model was able to reach the desired performance goal quickly.
Apart from the modeling slump of ready mix concrete, the synaptic
weights of neural networks were harnessed for analyzing the relative
importance of concrete design mix constituents on the slump value.
The sand and water constituents of the concrete design mix were
found to exhibit maximum importance on the concrete slump value.
Abstract: Fibrin degradation is an important part in prevention
or treatment of intravascular thrombosis and cardiovascular diseases.
Plasmin like fibrinolytic enzymes has given new hope to patient with
cardiovascular diseases by treating fibrin aggregation related diseases
with traditional plasminogen activator which have many side effects.
Various researches involving wide range of sources for production of
fibrinolytic proteases, from bacteria, fungi, insects and fermented
foods. But few have looked into endophytic fungi as a potential
source. Sixteen (16) endophytic fungi were isolated from Hibiscus sp.
leaves from six different locations in Shah Alam, Selangor. Only two
endophytic fungi, FH3 and S13 showed positive fibrinolytic protease
activities. FH3 produced 5.78cm and S13 produced 4.48cm on Skim
Milk Agar after 4 days of incubation at 27°C. Fibrinolytic activity
was observed; 3.87cm and 1.82cm diameter clear zone on fibrin plate
of FH3 and S13 respectively. 18srRNA was done for identification of
the isolated fungi with positive fibrinolytic protease. S13 had the
highest similarity (100%) to that of Penicillium citrinum strain TG2
and FH3 had the highest similarity (99%) to that of Fusarium sp.
FW2PhC1, Fusarium sp. 13002, Fusarium sp. 08006, Fusarium
equiseti strain Salicorn 8 and Fungal sp. FCASAn-2. Media
composition variation showed the effects of carbon nitrogen on
protein concentration, where the decrement of 50% of media
composition caused drastic decrease in protease of FH3 from 1.081 to
0.056 and also S13 from 2.946 to 0.198.
Abstract: This paper presents circular polar coordinates
transformation of periodic fuzzy membership function. The purpose
is identification of domain of periodic membership functions in
consequent part of IF-THEN rules. Proposed methods in this paper
remove complicatedness concerning domain of periodic membership
function from defuzzification in fuzzy approximate reasoning.
Defuzzification on circular polar coordinates is also proposed.
Abstract: This paper presents the design and analysis of Liquid
Crystal (LC) based tunable reflectarray antenna with different design
configurations within X-band frequency range. The effect of LC
volume used for unit cell element on frequency tunability and
reflection loss performance has been investigated. Moreover different
slot embedded patch element configurations have been proposed for
LC based tunable reflectarray antenna design with enhanced
performance. The detailed fabrication and measurement procedure
for different LC based unit cells has been presented. The waveguide
scattering parameter measured results demonstrated that by using the
circular slot embedded patch elements, the frequency tunability and
dynamic phase range can be increased from 180MHz to 200MHz and
120° to 124° respectively. Furthermore the circular slot embedded
patch element can be designed at 10GHz resonant frequency with a
patch volume of 2.71mm3 as compared to 3.47mm3 required for
rectangular patch without slot.
Abstract: There is an essential need for obtaining the mathematical representation of fish body undulations, which can be used for designing and building new innovative types of marine propulsion systems with less environmental impact. This research work presents a case study to derive the mathematical model for fish body movement. Observation and capturing image methods were used in this study in order to obtain a mathematical representation of Clariasbatrachus fish (catfish). An experiment was conducted by using an aquarium with dimension 0.609 m x 0.304 m x 0.304 m, and a 0.5 m ruler was attached at the base of the aquarium. Progressive Scan Monochrome Camera was positioned at 1.8 m above the base of the aquarium to provide swimming sequences. Seven points were marked on the fish body using white marker to indicate the fish movement and measuring the amplitude of undulation. Images from video recordings (20 frames/s) were analyzed frame by frame using local coordinate system, with time interval 0.05 s. The amplitudes of undulations were obtained for image analysis from each point that has been marked on fish body. A graph of amplitude of undulations versus time was plotted by using computer to derive a mathematical fit. The function for the graph is polynomial with nine orders.
Abstract: As Malaysia aims to be a developed country by year 2020; the construction industry has since been identified as a major catalyst for the country to attain the status. It is one of the sectors that contribute to most environmental pollutions. It is, therefore, important for the industry to implement sustainable construction practices to reduce the negative impacts that it has on the environment. However, most Malaysian developers have placed much focus on market demand and economic factors; neglecting the need for attention on environmental issues. The practice of sustainable construction is deemed to be an obstacle to achieve short-term economic goals due to the higher cost incurred in the operations. Hence, choices need to be made and a balance needs to be struck in weighing the long-term environmental benefits against immediate economic factors. This paper discusses the challenges faced by Malaysian developers in adopting sustainable practices in the construction industry and the cause of these challenges. It also looks into the achievements and breakthroughs that developers in Malaysia have achieved so far. The paper aims explores the long-term benefits of sustainable practices that would potentially raise awareness on the feasibility and economic potential of sustainable construction.
Abstract: Image segmentation process based on mathematical morphology has been studied in the paper. It has been established from the first principles of the morphological process, the entire segmentation is although a nonlinear signal processing task, the constituent wise, the intermediate steps are linear, bilinear and conformal transformation and they give rise to a non linear affect in a cumulative manner.
Abstract: A theoretical study has been presented to describe the boundary layer flow and heat transfer on an exponentially shrinking sheet with a variable wall temperature and suction, in the presence of magnetic field. The governing nonlinear partial differential equations are converted into ordinary differential equations by similarity transformation, which are then solved numerically using the shooting method. Results for the skin friction coefficient, local Nusselt number, velocity profiles as well as temperature profiles are presented through graphs and tables for several sets of values of the parameters. The effects of the governing parameters on the flow and heat transfer characteristics are thoroughly examined.