Abstract: The present work is a numerical simulation of
nanofluids flow in a double pipe heat exchanger provided with
porous baffles. The hot nanofluid flows in the inner cylinder, whereas
the cold nanofluid circulates in the annular gap. The Darcy-
Brinkman-Forchheimer model is adopted to describe the flow in the
porous regions, and the governing equations with the appropriate
boundary conditions are solved by the finite volume method. The
results reveal that the addition of metallic nanoparticles enhances the
rate of heat transfer in comparison to conventional fluids but this
augmentation is accompanied by an increase in pressure drop. The
highest heat exchanger performances are obtained when
nanoparticles are added only to the cold fluid.
Abstract: The aim of this study was to investigate the influence
of reaction temperature and wheat straw moisture content on the
pyrolysis product yields, in the temperature range of 475-575 °C.
Samples of straw with moisture contents from 1.5 wt % to 15.0 wt %
were fed to a bench scale Pyrolysis Centrifuge Reactor (PCR). The
experimental results show that the changes in straw moisture content
have no significant effect on the distribution of pyrolysis product
yields. The maximum bio-oil yields approximately 60 (wt %, on dry
ash free feedstock basis) was observed around 525 °C - 550 °C for all
straw moisture levels. The water content in the wet straw bio-oil was
the highest. The heating value of bio-oil and solid char were
measured and the percentages of its energy distribution were
calculated. The energy distributions of bio-oil, char and gas were 56-
69 % 24-33 %, and 2-19 %, respectively.
Abstract: The paper evaluates several hundred one-day-ahead
VaR forecasting models in the time period between the years 2004
and 2009 on data from six world stock indices - DJI, GSPC, IXIC,
FTSE, GDAXI and N225. The models model mean using the ARMA
processes with up to two lags and variance with one of GARCH,
EGARCH or TARCH processes with up to two lags. The models are
estimated on the data from the in-sample period and their forecasting
accuracy is evaluated on the out-of-sample data, which are more
volatile. The main aim of the paper is to test whether a model
estimated on data with lower volatility can be used in periods with
higher volatility. The evaluation is based on the conditional coverage
test and is performed on each stock index separately. The primary
result of the paper is that the volatility is best modelled using a
GARCH process and that an ARMA process pattern cannot be found
in analyzed time series.
Abstract: In this paper, the construction of fast algorithms for the computation of Periodic Walsh Piecewise-Linear PWL transform and the Periodic Haar Piecewise-Linear PHL transform will be presented. Algorithms for the computation of the inverse transforms are also proposed. The matrix equation of the PWL and PHL transforms are introduced. Comparison of the computational requirements for the periodic piecewise-linear transforms and other orthogonal transforms shows that the periodic piecewise-linear transforms require less number of operations than some orthogonal transforms such as the Fourier, Walsh and the Discrete Cosine transforms.
Abstract: In the present work, the performance of the particle
swarm optimization and the genetic algorithm compared as a typical
geometry design problem. The design maximizes the heat transfer
rate from a given fin volume. The analysis presumes that a linear
temperature distribution along the fin. The fin profile generated using
the B-spline curves and controlled by the change of control point
coordinates. An inverse method applied to find the appropriate fin
geometry yield the linear temperature distribution along the fin
corresponds to optimum design. The numbers of the populations, the
count of iterations and time to convergence measure efficiency.
Results show that the particle swarm optimization is most efficient
for geometry optimization.
Abstract: An automated wood recognition system is designed to
classify tropical wood species.The wood features are extracted based
on two feature extractors: Basic Grey Level Aura Matrix (BGLAM)
technique and statistical properties of pores distribution (SPPD)
technique. Due to the nonlinearity of the tropical wood species
separation boundaries, a pre classification stage is proposed which
consists ofKmeans clusteringand kernel discriminant analysis (KDA).
Finally, Linear Discriminant Analysis (LDA) classifier and KNearest
Neighbour (KNN) are implemented for comparison purposes.
The study involves comparison of the system with and without pre
classification using KNN classifier and LDA classifier.The results
show that the inclusion of the pre classification stage has improved
the accuracy of both the LDA and KNN classifiers by more than
12%.
Abstract: We investigate properties of convective solutions of the
Boussinesq thermal convection in a moderately rotating spherical
shell allowing the inner and outer sphere rotation due to the viscous
torque of the fluid. The ratio of the inner and outer radii of the
spheres, the Prandtl number and the Taylor number are fixed to 0.4,
1 and 5002, respectively. The inertial moments of the inner and outer
spheres are fixed to about 0.22 and 100, respectively. The Rayleigh
number is varied from 2.6 × 104 to 3.4 × 104. In this parameter
range, convective solutions transit from equatorially symmetric quasiperiodic
ones to equatorially asymmetric chaotic ones as the Rayleigh
number is increased. The transition route in the system allowing
rotation of both the spheres is different from that in the co-rotating
system, which means the inner and outer spheres rotate with the
same constant angular velocity: the convective solutions transit as
equatorially symmetric quasi-periodic solution → equatorially symmetric
chaotic solution → equatorially asymmetric chaotic solution
in the system allowing both the spheres rotation, while equatorially
symmetric quasi-periodic solution → equatorially asymmetric quasiperiodic
solution → equatorially asymmetric chaotic solution in the
co-rotating system.
Abstract: This paper presents an evaluation for a wavelet-based
digital watermarking technique used in estimating the quality of
video sequences transmitted over Additive White Gaussian Noise
(AWGN) channel in terms of a classical objective metric, such as
Peak Signal-to-Noise Ratio (PSNR) without the need of the original
video. In this method, a watermark is embedded into the Discrete
Wavelet Transform (DWT) domain of the original video frames
using a quantization method. The degradation of the extracted
watermark can be used to estimate the video quality in terms of
PSNR with good accuracy. We calculated PSNR for video frames
contaminated with AWGN and compared the values with those
estimated using the Watermarking-DWT based approach. It is found
that the calculated and estimated quality measures of the video
frames are highly correlated, suggesting that this method can provide
a good quality measure for video frames transmitted over AWGN
channel without the need of the original video.
Abstract: This work addresses the problem of optimizing
completely batch water-using network with multiple contaminants
where the flow change caused by mass transfer is taken into
consideration for the first time. A mathematical technique for
optimizing water-using network is proposed based on
source-tank-sink superstructure. The task is to obtain the freshwater
usage, recycle assignments among water-using units, wastewater
discharge and a steady water-using network configuration by
following steps. Firstly, operating sequences of water-using units are
determined by time constraints. Next, superstructure is simplified by
eliminating the reuse and recycle from water-using units with
maximum concentration of key contaminants. Then, the non-linear
programming model is solved by GAMS (General Algebra Model
System) for minimum freshwater usage, maximum water recycle and
minimum wastewater discharge. Finally, numbers of operating periods
are calculated to acquire the steady network configuration. A case
study is solved to illustrate the applicability of the proposed approach.
Abstract: In this paper a three dimensional thermal model of a
power toroidal transformer is proposed for both steady-state or
transient conditions. The influence of electric current and ambient
temperature on the temperature distribution, has been investigated.
To validate the three dimensional thermal model, some experimental
tests have been done. There is a good correlation between
experimental and simulation results.
Abstract: Polyphenolics and sugar are the components of many
fruit juices. In this work, the performance of ultra-filtration (UF) for
separating phenolic compounds from apple juice was studied by
performing batch experiments in a membrane module with an area of
0.1 m2 and fitted with a regenerated cellulose membrane of 1 kDa
MWCO. The effects of various operating conditions: transmembrane
pressure (3, 4, 5 bar), temperature (30, 35, 40 ºC), pH (2, 3, 4, 5),
feed concentration (3, 5, 7, 10, 15 ºBrix for apple juice) and feed flow
rate (1, 1.5, 1.8 L/min) on the performance were determined.
The optimum operating conditions were: transmembrane pressure
4 bar, temperature 30 ºC, feed flow rate 1 – 1.8 L/min, pH 3 and 10
Brix (apple juice). After performing ultrafiltration under these
conditions, the concentration of polyphenolics in retentate was
increased by a factor of up to 2.7 with up to 70% recovered in the
permeate and with approx. 20% of the sugar in that stream..
Application of diafiltration (addition of water to the concentrate) can
regain the flux by a factor of 1.5, which has been decreased due to
fouling. The material balance performed on the process has shown
the amount of deposits on the membrane and the extent of fouling in
the system. In conclusion, ultrafiltration has been demonstrated as a
potential technology to separate the polyphenolics and sugars from
their mixtures and can be applied to remove sugars from fruit juice.
Abstract: Commercially available lipases (Candida antarctica lipase B, Novozyme 435, Thermomyces lanuginosus lipase, and Lipozyme TL IM), as well as sol-gel immobilized lipases, have been screened for their ability to acylate regioselectively xylitol, sorbitol, and mannitol with a phenolic ester in a binary mixture of t-butanol and dimethylsulfoxide. HPLC and MALDI-TOF MS analysis revealed the exclusive formation of monoesters for all studied sugar alcohols. The lipases immobilized by the sol-gel entrapment method proved to be efficient catalysts, leading to high conversions (up to 60%) in the investigated acylation reactions. From a sequence of silane precursors with different nonhydrolyzable groups in their structure, the presence of octyl and i-butyl group was most beneficial for the catalytic activity of sol-gel entrapped lipases in the studied process.
Abstract: Compression algorithms reduce the redundancy in
data representation to decrease the storage required for that data.
Lossless compression researchers have developed highly
sophisticated approaches, such as Huffman encoding, arithmetic
encoding, the Lempel-Ziv (LZ) family, Dynamic Markov
Compression (DMC), Prediction by Partial Matching (PPM), and
Burrows-Wheeler Transform (BWT) based algorithms.
Decompression is also required to retrieve the original data by
lossless means. A compression scheme for text files coupled with
the principle of dynamic decompression, which decompresses only
the section of the compressed text file required by the user instead of
decompressing the entire text file. Dynamic decompressed files offer
better disk space utilization due to higher compression ratios
compared to most of the currently available text file formats.
Abstract: In H.264/AVC video encoding, rate-distortion
optimization for mode selection plays a significant role to achieve
outstanding performance in compression efficiency and video quality.
However, this mode selection process also makes the encoding
process extremely complex, especially in the computation of the ratedistortion
cost function, which includes the computations of the sum
of squared difference (SSD) between the original and reconstructed
image blocks and context-based entropy coding of the block. In this
paper, a transform-domain rate-distortion optimization accelerator
based on fast SSD (FSSD) and VLC-based rate estimation algorithm
is proposed. This algorithm could significantly simplify the hardware
architecture for the rate-distortion cost computation with only
ignorable performance degradation. An efficient hardware structure
for implementing the proposed transform-domain rate-distortion
optimization accelerator is also proposed. Simulation results
demonstrated that the proposed algorithm reduces about 47% of total
encoding time with negligible degradation of coding performance.
The proposed method can be easily applied to many mobile video
application areas such as a digital camera and a DMB (Digital
Multimedia Broadcasting) phone.
Abstract: Wireless LAN technologies have picked up
momentum in the recent years due to their ease of deployment, cost
and availability. The era of wireless LAN has also given rise to
unique applications like VOIP, IPTV and unified messaging.
However, these real-time applications are very sensitive to network
and handoff latencies. To successfully support these applications,
seamless roaming during the movement of mobile station has become
crucial. Nowadays, centralized architecture models support roaming
in WLANs. They have the ability to manage, control and
troubleshoot large scale WLAN deployments. This model is managed
by Control and Provision of Wireless Access Point protocol
(CAPWAP). This paper covers the CAPWAP architectural solution
along with its proposals that have emerged. Based on the literature
survey conducted in this paper, we found that the proposed
algorithms to reduce roaming latency in CAPWAP architecture do
not support seamless roaming. Additionally, they are not sufficient
during the initial period of the network. This paper also suggests
important design consideration for mobility support in future
centralized IEEE 802.11 networks.
Abstract: In this paper, a joint source-channel coding (JSCC) scheme for time-varying channels is presented. The proposed scheme uses hierarchical framework for both source encoder and transmission via QAM modulation. Hierarchical joint source channel codes with hierarchical QAM constellations are designed to track the channel variations which yields to a higher throughput by adapting certain parameters of the receiver to the channel variation. We consider the problem of still image transmission over time-varying channels with channel state information (CSI) available at 1) receiver only and 2) both transmitter and receiver being informed about the state of the channel. We describe an algorithm that optimizes hierarchical source codebooks by minimizing the distortion due to source quantizer and channel impairments. Simulation results, based on image representation, show that, the proposed hierarchical system outperforms the conventional schemes based on a single-modulator and channel optimized source coding.
Abstract: This article presents a computationally tractable probabilistic model for the relation between the complex wavelet coefficients of two images of the same scene. The two images are acquisitioned at distinct moments of times, or from distinct viewpoints, or by distinct sensors. By means of the introduced probabilistic model, we argue that the similarity between the two images is controlled not by the values of the wavelet coefficients, which can be altered by many factors, but by the nature of the wavelet coefficients, that we model with the help of hidden state variables. We integrate this probabilistic framework in the construction of a new image registration algorithm. This algorithm has sub-pixel accuracy and is robust to noise and to other variations like local illumination changes. We present the performance of our algorithm on various image types.
Abstract: Korea Train eXpress (KTX) is now being operated,
which allows Korea being one of the countries that operates the
high-speed rail system. The high-speed rail has its advantage of short
time transportation of population and materials, which lead to many
researches performed in this matter. In the case of high speed classical
trackbed system, the maintenance and usability of gravel ballast
system is costly. Recently, the concrete trackbed structure has been
introduced as a replacement of classical trackbed system. In this case,
the sleeper plays a critical role. Current study investigated to develop
the track sleepers readily applicable to the top of the asphalt trackbed,
as part of the trcakbed study utilizing the asphalt material. Among
many possible shapes and design of sleepers, current study proposed
two types of wide-sleepers according to the shear-key installation
method. The structural behavior analysis and safety evaluation on each
case was conducted using Korean design standard.
Abstract: This paper describes an efficient and practical method
for economic dispatch problem in one and two area electrical power
systems with considering the constraint of the tie transmission line
capacity constraint. Direct search method (DSM) is used with some
equality and inequality constraints of the production units with any
kind of fuel cost function. By this method, it is possible to use several
inequality constraints without having difficulty for complex cost
functions or in the case of unavailability of the cost function
derivative. To minimize the number of total iterations in searching,
process multi-level convergence is incorporated in the DSM.
Enhanced direct search method (EDSM) for two area power system
will be investigated. The initial calculation step size that causes less
iterations and then less calculation time is presented. Effect of the
transmission tie line capacity, between areas, on economic dispatch
problem and on total generation cost will be studied; line
compensation and active power with reactive power dispatch are
proposed to overcome the high generation costs for this multi-area
system.
Abstract: This paper presents a comparison of average outgoing
quality limit of the MCSP-2-C plan with MCSP-C when MCSP-2-C
has been developed from MCSP-C. The parameters used in MCSP-2-
C are: i (the clearance number), c (the acceptance number), m (the
number of conforming units to be found before allowing c nonconforming
units in the sampling inspection), f1 and f2 (the sampling
frequency at level 1 and 2, respectively). The average outgoing
quality limit (AOQL) values from two plans were compared and we
found that for all sets of i, r, and c values, MCSP-2-C gives higher
values than MCSP-C. For all sets of i, r, and c values, the average
outgoing quality values of MCSP-C and MCSP-2-C are similar when
p is low or high but is difference when p is moderate.