Abstract: This research focuses on the optimization of glazed
surfaces and the assessment of possible solar gains in industrial
buildings. Existing window rating methods for single windows were
evaluated and a new method for a simple analysis of energy gains and
losses by single windows was introduced. Furthermore extensive
transient building simulations were carried out to appraise the
performance of low cost polycarbonate multi-cell sheets in
interaction with typical buildings for industrial applications. Mainly
energy saving potential was determined by optimizing the orientation
and area of such glazing systems in dependency on their thermal
qualities. Moreover the impact on critical aspects such as summer
overheating and daylight illumination was considered to ensure the
user comfort and avoid additional energy demand for lighting or
cooling. Hereby the simulated heating demand could be reduced by
up to 1/3 compared to traditional architecture of industrial halls using
mainly skylights.
Abstract: Novel bio-based polymer electrolyte was synthesized
with LiClO4 as the main source of charge carrier. Initially,
polyurethane-LiClO4 polymer electrolytes were synthesized via
prepolymerization method with different NCO/OH ratios and labelled
them as PU1, PU2, PU3 and PU4. Fourier transform infrared (FTIR)
analysis indicates the co-ordination between Li+ ion and polyurethane
in PU1. Differential scanning calorimetry (DSC) analysis indicates
PU1 has the highest glass transition temperature (Tg) corresponds to
the most abundant urethane group which is the hard segment in PU1.
Scanning electron microscopy (SEM) shows the good miscibility
between lithium salt and the polymer. The study found that PU1
possessed the greatest ionic conductivity and the lowest activation
energy, Ea. All the polyurethanes exhibited linear Arrhenius
variations indicating ion transport via simple lithium ion hopping in
polyurethane. This research proves the NCO content in polyurethane
plays an important role in affecting the ionic conductivity of this
polymer electrolyte.
Abstract: The effect of trucks on the level of service is
determined by considering passenger car equivalents (PCE) of trucks.
The current version of Highway Capacity Manual (HCM) uses a
single PCE value for all tucks combined. However, the composition
of truck traffic varies from location to location; therefore, a single
PCE value for all trucks may not correctly represent the impact of
truck traffic at specific locations. Consequently, present study
developed separate PCE values for single-unit and combination
trucks to replace the single value provided in the HCM on different
freeways. Site specific PCE values, were developed using concept of
spatial lagging headways (that is the distance between rear bumpers
of two vehicles in a traffic stream) measured from field traffic data.
The study used data from four locations on a single urban freeway
and three different rural freeways in Indiana. Three-stage-leastsquares
(3SLS) regression techniques were used to generate models
that predicted lagging headways for passenger cars, single unit trucks
(SUT), and combination trucks (CT). The estimated PCE values for
single-unit and combination truck for basic urban freeways (level
terrain) were: 1.35 and 1.60, respectively. For rural freeways the
estimated PCE values for single-unit and combination truck were:
1.30 and 1.45, respectively. As expected, traffic variables such as
vehicle flow rates and speed have significant impacts on vehicle
headways. Study results revealed that the use of separate PCE values
for different truck classes can have significant influence on the LOS
estimation.
Abstract: Theoretical optimization of a copper-water negative
inclination heat pipe with internal composite wick structure had been
performed, regarding a new introduced parameter: the ratio between
the coarse mesh wraps and the fine mesh wraps of the composite
wick. Since in many cases, the design of a heat pipe matches specific
thermal requirements and physical limitations, this work
demonstrates the optimization of a 1m length, 8mm internal diameter
heat pipe without an adiabatic section, at a negative inclination angle
of -10º. The optimization is based on a new introduced parameter, LR:
the ratio between the coarse mesh wraps and the fine mesh wraps.
Abstract: In the present work, the effects of additives, including
contents of the added antioxidants and type of the selected metallic
stearates (either calcium stearate (CaSt) or zinc stearate (ZnSt)), on
the thermal stabilities of carbon black (CB)/high density polyethylene
(HDPE) compounds were studied. The results showed that the AO
contents played a key role in the thermal stabilities of the CB/HDPE
compounds — the higher the AO content, the higher the thermal
stabilities. Although the CaSt-containing compounds were slightly
superior to those with ZnSt in terms of the thermal stabilities, the
remaining solid residue of CaSt after heated to the temperature of 600
°C (mainly calcium carbonate (CaCO3) as characterized by the X-ray
diffraction (XRD) technique) seemed to catalyze the decomposition
of CB in the HDPE-based compounds. Hence, the quantification of
CB in the CaSt-containing compounds with a muffle furnace gave an
inaccurate CB content — much lower than actual value. However,
this phenomenon was negligible in the ZnSt-containing system.
Abstract: OEE has been used in many industries as measure of
performance. However due to limitations of original OEE, it has been
modified by various researchers. OEE for mining application is
special version of classic equation, carries these limitation over. In
this paper it has been aimed to modify the OEE for mining
application by introducing the weights to the elements of it and
termed as Mine Production index (MPi). As a special application of
new index MPishovel has been developed by authors. This can be used
for evaluating the shovel effectiveness. Based on analysis, utilization
followed by performance and availability were ranked in this order.
To check the applicability of this index, a case study was done on
four electrical and one hydraulic shovel in a Swedish mine. The
results shows that MPishovel can evaluate production effectiveness of
shovels and can determine effectiveness values in optimistic view
compared to OEE. MPi with calculation not only give the
effectiveness but also can predict which elements should be focused
for improving the productivity.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: The majority of contemporary insulation materials
commonly used in the building industry is made from non-renewable
raw materials; furthermore, their production often brings high energy
costs. A long-term trend as far as sustainable development is
concerned has been the reduction of energy and material demands of
building material production. One of the solutions is the possibility of
using easily renewable natural raw material sources which are
considerably more ecological and their production is mostly less
energy-consuming compared to the production of normal insulations
(mineral wool, polystyrene). The paper describes the results of
research focused on the development of thermal and acoustic
insulation materials based on natural fibres intended for floor
constructions. Given the characteristic open porosity of natural fibre
materials, the hygrothermal behaviour of the developed materials was
studied. Especially the influence of relative humidity and temperature
on thermal insulation properties was observed.
Abstract: The effect of Zn2+, Mg2+, and Ba2+ on Saccharomyces
pastorianus performance was evaluated in this study at independent
and three variable combinations. After 96 h of fermentation, high
wort fermentability (%F) = 29.53 was obtained in medium containing
900:4 ppm Mg2+ + Ba2+. Increased ethanol yield 7.35 %(v/v) and
7.13 %(v/v) were obtained in media containing 900:4 ppm Mg2+ +
Ba2+ and 12:900 ppm Zn2+ + Mg2+. Decrease %F = 22.54 and ethanol
yield 6.18 % (v/v) was obtained in medium containing 12:4 ppm Zn2+
+ Ba2+. In media containing the individual ions, increased %F =
27.94 and 26.03 were recorded for media containing 700 ppm Mg2+
and 2 ppm Ba2+ , with ethanol yield of 7.88% (v/v) and 7.62% (v/v)
respectively. Reduced %F and ethanol yield was observed for 10 ppm
Zn2+ and 4 ppm Ba2+ media. The impact of Ba2+ at 1 and 2 ppm was
significant.
Abstract: The paper deals with current issues in research of
advanced methods to increase reliability of traditional timber
structural elements. It analyses the issue of strengthening of bent
timber beams, such as ceiling beams in old (historical) buildings with
additional concrete slab in combination with externally bonded fibre -
reinforced polymer. The paper describes experimental testing of
composite timber-concrete beam with FRP reinforcement and
compares results with FEM analysis.
Abstract: This paper presents a hybrid three phase rectifier for
high power factor application. This rectifier is composed by zero
voltage transition (ZVT) and zero current transition (ZCT) boost
converter with three phase diode bridge rectifier, in parallel with a six
pulse three phase pulse width modulation (PWM) controlled rectifier.
The proposed topology is capable of high power factor with DC
output voltage regulation by providing sinusoidal input. Also, it
increases the overall efficiency of the new hybrid rectifier to 94.56%
and the total harmonic distortion of the hybrid structure varies from
0% to 16% at nominal output power. This topology was simulated in
MATLAB/SIMULINK environment and the output waveforms
presented with experimental result.
Abstract: The objective of the study was to select the survival of
probiotic strains when exposed to acidic and bile salts condition. Four
probiotic strains Lactobacillus casei subsp. rhamnosus TISTR 047,
Lactobacillus casei TISTR 1500, Lactobacillus acidophilus TISTR
1338 and Lactobacillus plantarum TISTR 1465 were cultured in
MRS broth and incubated at 35ºC for 15 hours before being inoculated
into acidic condition 5 M HCl, pH 2 for 2 hours and bile salt 0.3%,
pH 5.8 for 8 hour. The survived probiotics were counted in MRS agar.
Among four stains, Lactobacillus casei subsp. rhamnosus TISTR 047
was the highest tolerance specie. Lactobacillus casei subsp.
rhamnosus TISTR 047 reduced 6.74±0.07 log CFU/ml after growing
in acid and 5.52±0.05 log CFU/ml after growing in bile salt. Then,
double emulsion of microorganisms was chosen to encapsulate before
spray drying. Spray drying was done with the inlet temperature 170ºC
and outlet temperature 80ºC. The results showed that the survival of
encapsulated Lactobacillus casei subsp. rhamnosus TISTR 047 after
spray drying decreased from 9.63 ± 0.32 to 8.31 ± 0.11 log CFU/ml
comparing with non-encapsulated, 9.63 ± 0.32 to 4.06 ± 0.08 log
CFU/ml. Therefore, Lactobacillus casei subsp. rhamnosus TISTR 047
would be able to survive in gastrointestinal and spray drying condition.
Abstract: Persea declinata (Bl.) Kosterm is a member of the
Lauraceae family, widely distributed in Southeast Asia. It is from the
same genus with avocado (Persea americana Mill), which is widely
consumed as food and for medicinal purposes. In the present study,
we examined the anticancer properties of Persea declinata (Bl.)
Kosterm bark methanolic crude extract (PDM). PDM exhibited a
potent antiproliferative effect in MCF-7 human breast cancer cells,
with an IC50 value of 16.68 .g/mL after 48h of treatment. We
observed that PDM caused cell cycle arrest and subsequent apoptosis
in MCF-7 cells, as exhibited by increased population at G0/G1 phase,
higher lactate dehydrogenase (LDH) release, and DNA
fragmentation. Mechanistic studies showed that PDM caused
significant elevation in ROS production, leading to perturbation of
mitochondrial membrane potential, cell permeability, and activation
of caspases-3/7. On the other hand, real-time PCR and Western blot
analysis showed that PDM treatment increased the expression of the
proapoptotic molecule, Bax, but decreased the expression of
prosurvival proteins, Bcl-2 and Bcl-xL, in a dose-dependent manner.
These findings imply that PDM could inhibit proliferation in MCF-7
cells via cell cycle arrest and apoptosis induction, indicating its
potential as a therapeutic agent worthy of further development.
Abstract: The manufacturing technology of band cotton is very
delicate and depends to choice of certain parameters such as torsion
of warp yarn.
The fabric elasticity is achieved without the use of any elastic
material, chemical expansion, artificial or synthetic and it’s capable
of creating pressures useful for therapeutic treatments.
Before use, the band is subjected to treatments of specific
preparation for obtaining certain elasticity, however, during its
treatment, there are some regression parameters. The dependence of
manufacturing parameters on the quality of the chemical treatment
was confirmed.
The aim of this work is to improve the properties of the fabric
through the development of manufacturing technology appropriately.
Finally for the treatment of the strip pancake 100% cotton, a
treatment method is recommended.
Abstract: This article presents summary on preparation and
characterization of zinc, copper, cadmium and cobalt chromite
nanocrystals, embedded in an amorphous silica matrix. The
ZnCr2O4/SiO2, CuCr2O4/SiO2, CdCr2O4/SiO2 and CoCr2O4/SiO2
nanocomposites were prepared by a conventional sol-gel method
under acid catalysis. Final heat treatment of the samples was carried
out at temperatures in the range of 900−1200 ◦C to adjust the
phase composition and the crystallite size, respectively. The resulting
samples were characterized by Powder X-ray diffraction (PXRD),
High Resolution Transmission Electron Microscopy (HRTEM),
Raman/FTIR spectroscopy and magnetic measurements. Formation
of the spinel phase was confirmed in all samples. The average size of
the nanocrystals was determined from the PXRD data and by direct
particle size observation on HRTEM; both results were correlated.
The mean particle size (reviewed by HRTEM) was in the range from
∼4 to 46 nm. The results showed that the sol-gel method can be
effectively used for preparation of the spinel chromite nanoparticles
embedded in the silica matrix and the particle size is driven by the
type of the cation A2+ in the spinel structure and the temperature
of the final heat treatment. Magnetic properties of the nanocrystals
were found to be just moderately modified in comparison to the bulk
phases.
Abstract: Load Forecasting plays a key role in making today's
and future's Smart Energy Grids sustainable and reliable. Accurate
power consumption prediction allows utilities to organize in advance
their resources or to execute Demand Response strategies more
effectively, which enables several features such as higher
sustainability, better quality of service, and affordable electricity
tariffs. It is easy yet effective to apply Load Forecasting at larger
geographic scale, i.e. Smart Micro Grids, wherein the lower available
grid flexibility makes accurate prediction more critical in Demand
Response applications. This paper analyses the application of
short-term load forecasting in a concrete scenario, proposed within the
EU-funded GreenCom project, which collect load data from single
loads and households belonging to a Smart Micro Grid. Three
short-term load forecasting techniques, i.e. linear regression, artificial
neural networks, and radial basis function network, are considered,
compared, and evaluated through absolute forecast errors and training
time. The influence of weather conditions in Load Forecasting is also
evaluated. A new definition of Gain is introduced in this paper, which
innovatively serves as an indicator of short-term prediction
capabilities of time spam consistency. Two models, 24- and
1-hour-ahead forecasting, are built to comprehensively compare these
three techniques.
Abstract: Artemisia species, which are medically beneficial, are
widespread in temperate regions of both Northern and Southern
hemispheres among which Iran is located. About 35 species of
Artemisia are indigenous in Iran among them some are widespread in
all or most provinces, yet some are restricted to some specific
regions. In this review paper, initially, GC-Mass results of some
experiments done in different provinces of Iran are mentioned among
them some compounds are common among species, some others are
mostly restricted to other species; after that, medical advantages
based on some researches on species of this genus are reviewed;
different qualities such as anti-leishmania, anti-bacteria, antiviral as
well as anti-proliferative could be mentioned.
Abstract: Nonalcoholic fatty liver disease (NAFLD) has
increased in conjunction with obesity. The accuracy of risk factors
for detecting NAFLD in obese adolescents has not undergone a
formal evaluation. The aim of this study was to evaluate predictors of
NAFLD among Egyptian female obese adolescents. The study
included 162 obese female adolescents. All were subjected to
anthropometry, biochemical analysis and abdominal ultrasongraphic
assessment. Metabolic syndrome (MS) was diagnosed according to
the IDF criteria. Significant association between presence of MS and
NAFLD was observed. Obese adolescents with NAFLD had
significantly higher levels of ALT, triglycerides, fasting glucose,
insulin, blood pressure and HOMA-IR, whereas decreased HDL-C
levels as compared with obese cases without NAFLD. Receiver–
operating characteristic (ROC) curve analysis shows that ALT is a
sensitive predictor for NAFLD, confirming that ALT can be used as a
marker of NAFLD.
Abstract: Due to reduced stiffness, research on second
generation titanium alloys for implant applications, like the
metastable β-titanium alloy Ti-15Mo, become more and more
important in the recent years. The machinability of these alloys is
generally poor leading to problems during implant production and
comparably large production costs. Therefore, in the present study,
Ti-15Mo was alloyed with 0.8 wt.-% of the rare earth metals
lanthanum (Ti-15Mo+0.8La) and neodymium (Ti-15Mo+0.8Nd) to
improve its machinability. Their microstructure consisted of a
titanium matrix and micrometer-size particles of the rare earth metals
and two of their oxides. The particles stabilized the microstructure as
grain growth was minimized. As especially the ductility might be
affected by the precipitates, the behavior of Ti-15Mo+0.8La and Ti-
15Mo+0.8Nd was investigated during static and dynamic
deformation at elevated temperature to develop a processing route.
The resulting mechanical properties (static strength and ductility)
were similar in all investigated alloys.
Abstract: In the present work, the effect of load and sliding
distance on the performance tribology of commercially used
aluminium-silicon engine block and piston was evaluated at ambient
conditions with humidity of 80% under dry sliding conditions using a
pin-on-disc with two different loads of 5N and 20N yielding applied
pressure of 0.30MPa and 1.4MPa, respectively, at sliding velocity of
0.29ms-1 and with varying sliding distance ranging from 260m-
4200m. Factors and conditions that had significant effect were
identified. The results showed that the load and the sliding distance
affect the wear rate of the alloys and the wear rate increased with
increasing load for both the alloys. Wear rate also increases almost
linearly at low loads and increase to a maximum then attain a plateau
with increasing sliding distance. For both applied loads the piston
alloy showed the better performance due to higher Ni and Mg
content. The worn surface and wear debris was characterized by
optical microscope, SEM and EDX analyzer. The worn surface was
characterized by surface with shallow grooves at loads while the
groove width and depth increased as the loads increases. Oxidative
wear was found to be the predominant mechanisms in the dry sliding
of Al-Si alloys at low loads.