Abstract: Geosynthetics have proved to be suitable for
reinforced soil retaining walls. Based on the increasing uses of
geosynthetic reinforced soil systems in the regions, which bear
frequent earthquakes, the study of dynamic behavior of structures
seems necessary. Determining the reinforcement forces is; therefore,
one of the most important and main points of discussions in
designing retaining walls, by which we prevent from conservative
planning. Thus, this paper intended to investigate the effects of such
parameters as wall height, acceleration type, vertical spacing of
reinforcement, type of reinforcement and soil type on forces and
deformation through numerical modeling of the geosynthetic
reinforced soil retaining walls (GRSRW) under dynamic loading with
finite difference method by using FLAC. The findings indicate rather
positive results with each parameter.
Abstract: One of the efficient factors in comprehensive
development of an area is to provide water sources and on the other
hand the appropriate management of them. Population growth and
nourishment security for such a population necessitate the
achievement of constant development besides the reforming of
traditional management in order to increase the profit of sources; In
this case, the constant exploitation of sources for the next generations
will be considered in this program. The achievement of this
development without the consideration and possibility of water
development will be too difficult. Zayanderood basin with 41500
areas in square kilometers contains 7 sub-basins and 20 units of
hydrologic. In this basin area, from the entire environment
descending, just a small part will enter into the river currents and the
rest will be out of efficient usage by various ways. The most
important surface current of this basin is Zayanderood River with
403 kilometers length which is originated from east slopes of Zagros
mount and after draining of this basin area it will enter into
Gaavkhooni pond. The existence of various sources and
consumptions of water in Zayanderood basin, water transfer of the
other basin areas into this basin, of course the contradiction between
the upper and lower beneficiaries, the existence of worthwhile
natural ecosystems such as Gaavkhooni swamp in this basin area and
finally, the drought condition and lack of water in this area all
necessitate the existence of comprehensive management of water
sources in this central basin area of Iran as this method is a kind of
management which considers the development and the management
of water sources as an equilibrant way to increase the economical
and social benefits. In this study, it is tried to survey the network of
surface water sources of basin in upper and lower sections; at the
most, according to the difficulties and deficiencies of an efficient
management of water sources in this basin area, besides the
difficulties of water draining and the destructive phenomenon of
flood-water, the appropriate guidelines according to the region
conditions are presented in order to prevent the deviation of water in
upper sections and development of regions in lower sections of
Zayanderood dam.
Abstract: Single crystals of Magnesium alloys such as Mg-1Al,
Mg-1Zn-0.5Y, Mg-3Li, and AZ31 alloys were successfully fabricated in this study by employing the modified Bridgman method. Single
crystals of pure Mg were also made in this study. To determine the exact orientation of crystals, Laue back-reflection method and pole figure measurement were carried out on each single crystal. Dimensions of single crystals were 10 mm in diameter and 120 mm in
length. Hardness and compression tests were conducted and the results
revealed that hardness and the strength strongly depended on the
orientation. The closer to basal one the orientation was, the higher hardness and compressive strength were. The effect of alloying was
not higher than that of orientation. After compressive deformation of single crystals, the orientation of the crystals was found to rotate and to be parallel to the basal orientation.
Abstract: Question answering (QA) aims at retrieving precise information from a large collection of documents. Most of the Question Answering systems composed of three main modules: question processing, document processing and answer processing. Question processing module plays an important role in QA systems to reformulate questions. Moreover answer processing module is an emerging topic in QA systems, where these systems are often required to rank and validate candidate answers. These techniques aiming at finding short and precise answers are often based on the semantic relations and co-occurrence keywords. This paper discussed about a new model for question answering which improved two main modules, question processing and answer processing which both affect on the evaluation of the system operations. There are two important components which are the bases of the question processing. First component is question classification that specifies types of question and answer. Second one is reformulation which converts the user's question into an understandable question by QA system in a specific domain. The objective of an Answer Validation task is thus to judge the correctness of an answer returned by a QA system, according to the text snippet given to support it. For validating answers we apply candidate answer filtering, candidate answer ranking and also it has a final validation section by user voting. Also this paper described new architecture of question and answer processing modules with modeling, implementing and evaluating the system. The system differs from most question answering systems in its answer validation model. This module makes it more suitable to find exact answer. Results show that, from total 50 asked questions, evaluation of the model, show 92% improving the decision of the system.
Abstract: Since its independence in 1962, Algeria has struggled
to establish an educational system tailored to the needs of the
population it may address. Considering the historical connection with
France, Algeria has always looked at the French language as a
cultural imperative until late in the seventies. After the Arabization
policy of 1971 and the socioeconomic changes taking place
worldwide, the use of English as a communicating vehicle started to
gain more space within globalized Algeria. Consequently, disparities
in the use of French started to fade away at the cross-roads leaving
more space to the teaching of English as a second foreign language.
Moreover, the introduction of the Bologna Process and the
European Credit Transfer System in Higher Education has
necessitated some innovations in the design and development of new
curricula adapted to the socioeconomic market. In this paper, I will
try to highlight the important historical dimensions Algeria has taken
towards the implementation of an English language methodology and
to the status it acquired from second foreign language, to first foreign
language to “the language of knowledge and sciences". I will also
propose new pedagogical perspectives for a better treatment of the
English language in order to encourage independent and autonomous
learning.
Abstract: This work investigated the steady state and dynamic
simulation of a fixed bed industrial naphtha reforming reactors. The
performance of the reactor was investigated using a heterogeneous
model. For process simulation, the differential equations are solved
using the 4th order Runge-Kutta method .The models were validated
against measured process data of an existing naphtha reforming plant.
The results of simulation in terms of components yields and
temperature of the outlet were in good agreement with empirical data.
The simple model displays a useful tool for dynamic simulation,
optimization and control of naphtha reforming.
Abstract: In this article, biomechanical aspects of hen-s eggshell as a natural ceramic structure are studied. The images, taken by a scanning electron microscope (SEM), are used to investigate the microscopic aspects of the egg. It is observed that eggshell has a three-layered microstructure with different morphological and structural characteristics. Studies on the eggshell membrane (ESM) as a prosperous tissue suggest that it is placed to prevent the penetration of microorganisms into the egg. Finally, numerical models of the egg are presented to study the stress distribution and its deformation under different loading conditions. The effects of two different types of loading (hydrostatic and point loadings) on two different shell models (with constant and variable thicknesses) are investigated in detail.
Abstract: In this paper fatigue crack initiation and propagation in notched plate under constant amplitude loading through tensile residual stress field of 2024 T351 Al-alloy plate were investigated. Residual stress field was generated by plastic deformation using finite element method (FEM) where isotropic hardening in Von Mises model was applied. Simulation of fatigue behavior was made on AFGROW code. It was shown that the fatigue crack initiation and propagation were affected by level of residual stress filed. In this investigation, the presence of tensile residual stresses at notch (hole) reduces considerably the total fatigue life. It was shown that the decreasing in stress reduces the fatigue crack growth rates.
Abstract: Over the course of the past century, the global
automotive industry-s stance towards safety has evolved from one of
contempt to one nearing reverence. A suspension system that
provides safe handling and cornering capabilities can, with the help
of an efficient braking system, improve safety to a large extent. The
aim of this research is to propose a new automotive brake rotor
design and to compare it with automotive vented disk rotor. Static
structural and transient thermal analysis have been carried out on the
vented disk rotor and proposed rotor designs to evaluate and compare
their performance. Finite element analysis was employed for both
static structural and transient thermal analysis. Structural analysis
was carried out to study the stress and deformation pattern of the
rotors under extreme loads. Time varying temperature load was
applied on the rotors and the temperature distribution was analysed
considering cooling parameters (convection and radiation). This
dissertation illustrates the use of Finite Element Methods to examine
models, concluding with a comparative study of the proposed rotor
design and the conventional vented disk rotor for structural stability
and thermal efficiency.
Abstract: The electric power industry is currently undergoing an unprecedented reform. One of the most exciting and potentially profitable recent developments is increasing usage of artificial intelligence techniques. The intention of this paper is to give an overview of using neural network (NN) techniques in power systems. According to the growth rate of NNs application in some power system subjects, this paper introduce a brief overview in fault diagnosis, security assessment, load forecasting, economic dispatch and harmonic analyzing. Advantages and disadvantages of using NNs in above mentioned subjects and the main challenges in these fields have been explained, too.
Abstract: This paper presents the results of thermo-mechanical
characterization of Glass/Epoxy composite specimens using Infrared
Thermography technique. The specimens used for the study were
fabricated in-house with three different lay-up sequences and tested
on a servo hydraulic machine under uni-axial loading. Infrared
Camera was used for on-line monitoring surface temperature changes
of composite specimens during tensile deformation.
Experimental results showed that thermomechanical
characteristics of each type of specimens were distinct. Temperature
was found to be decreasing linearly with increasing tensile stress in
the elastic region due to thermo-elastic effect. Yield point could be
observed by monitoring the change in temperature profile during
tensile testing and this value could be correlated with the results
obtained from stress-strain response. The extent of prior plastic
deformation in the post-yield region influenced the slopes of
temperature response during tensile loading. Partial unloading and
reloading of specimens post-yield results in change in slope in elastic
and plastic regions of composite specimens.
Abstract: The neural stimulation has been gaining much interest in neuromodulation research and clinical trials. For efficiency, there is a need for variable electrical stimulation such as current and voltage stimuli as well as wireless framework. In this regard, we develop the wireless neural stimulator capable of voltage and current stimuli. The system consists of ZigBee which is a wireless communication module and stimulus generator. The stimulus generator with 8-bits resolution enable both mono-polar and bi-polar waveform in voltage (-3.3~3.3V) and current(-330~330µA) stimulus mode which is controllable. The experimental results suggest that the proposed neural stimulator can play a role as an effective approach for neuromodulation.
Abstract: In this work, we present a reliable framework to solve boundary value problems with particular significance in solid mechanics. These problems are used as mathematical models in deformation of beams. The algorithm rests mainly on a relatively new technique, the Variational Iteration Method. Some examples are given to confirm the efficiency and the accuracy of the method.
Abstract: This study deals with the experimental investigation
and theoretical modeling of Semi crystalline polymeric materials with
a rubbery amorphous phase (HDPE) subjected to a uniaxial cyclic
tests with various maximum strain levels, even at large deformation.
Each cycle is loaded in tension up to certain maximum strain and
then unloaded down to zero stress with N number of cycles. This
work is focuses on the measure of the volume strain due to the
phenomena of damage during this kind of tests. On the basis of
thermodynamics of relaxation processes, a constitutive model for
large strain deformation has been developed, taking into account the
damage effect, to predict the complex elasto-viscoelastic-viscoplastic
behavior of material. A direct comparison between the model
predictions and the experimental data show that the model accurately
captures the material response. The model is also capable of
predicting the influence damage causing volume variation.
Abstract: The paper evaluates the ongoing reform of VAT in the Czech Republic in terms of impacts on individual households. The main objective is to analyse the impact of given changes on individual households. The adopted method is based on the data related to household consumption by individual household quintiles; obtained data are subjected to micro-simulation examining. Results are discussed in terms of vertical tax justice. Results of the analysis reveal that VAT behaves regressively and a sole consolidation of rates at a higher level only increases the regression of this tax in the Czech Republic.
Abstract: This paper gives an overview of a deep drawing
process by pressurized liquid medium separated from the sheet by a
rubber diaphragm. Hydroforming deep drawing processing of sheet
metal parts provides a number of advantages over conventional
techniques. It generally increases the depth to diameter ratio possible
in cup drawing and minimizes the thickness variation of the drawn
cup. To explore the deformation mechanism, analytical and
numerical simulations are used for analyzing the drawing process of
an AA6061-T4 blank. The effects of key process parameters such as
coefficient of friction, initial thickness of the blank and radius
between cup wall and flange are investigated analytically and
numerically. The simulated results were in good agreement with the
results of the analytical model. According to finite element
simulations, the hydroforming deep drawing method provides a more
uniform thickness distribution compared to conventional deep
drawing and decreases the risk of tearing during the process.
Abstract: Flow through micro and mini channels requires relatively
high driving pressure due to the large fluid pressure drop
through these channels. Consequently the forces acting on the walls of
the channel due to the fluid pressure are also large. Due to these forces
there are displacement fields set up in the solid substrate containing
the channels. If the movement of the substrate is constrained at some
points, then stress fields are established in the substrate. On the other
hand, if the deformation of the channel shape is sufficiently large
then its effect on the fluid flow is important to be calculated. Such
coupled fluid-solid systems form a class of problems known as fluidstructure
interactions. In the present work a co-located finite volume
discretization procedure on unstructured meshes is described for
solving fluid-structure interaction type of problems. A linear elastic
solid is assumed for which the effect of the channel deformation
on the flow is neglected. Thus the governing equations for the
fluid and the solid are decoupled and are solved separately. The
procedure is validated by solving two benchmark problems, one from
fluid mechanics and another from solid mechanics. A fluid-structure
interaction problem of flow through a U-shaped channel embedded
in a plate is solved.
Abstract: Titanium alloys like Ti-6Al-2Sn-4Zr-6Mo (Ti-
6246) are widely used in aerospace applications. Component
manufacturing, however, is difficult and expensive as their
machinability is extremely poor. A thorough understanding of the
chip formation process is needed to improve related metal cutting
operations.In the current study, orthogonal cutting experiments have
been performed and theresulting chips were analyzed by optical
microscopy and scanning electron microscopy.Chips from aTi-
6246ingot were produced at different cutting speeds and cutting
depths. During the experiments, depending of the cutting conditions,
continuous or segmented chips were formed. Narrow, highly
deformed and grain oriented zones, the so-called shear zone,
separated individual segments. Different material properties have
been measured in the shear zones and the segments.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: terrorism and extremism are among the most
dangerous and difficult to forecast the phenomena of our time, which
are becoming more diverse forms and rampant. Terrorist attacks often
produce mass casualties, involve the destruction of material and
spiritual values, beyond the recovery times, sow hatred among
nations, provoke war, mistrust and hatred between the social and
national groups, which sometimes can not be overcome within a
generation. Currently, the countries of Central Asia are a topical issue
– the threat of terrorism and religious extremism, which grow not
only in our area, but throughout the world. Of course, in each of the
terrorist threat is assessed differently. In our country the problem of
terrorism should not be acutely. Thus, after independence and
sovereignty of Kazakhstan has chosen the path of democracy,
progress and free economy. With the policy of the President of
Kazakhstan Nursultan Nazarbayev and well-organized political and
economic reforms, there has been economic growth and rising living
standards, socio-political stability, ensured civil peace and accord in
society [1].