Abstract: Face and facial expressions play essential roles in
interpersonal communication. Most of the current works on the facial
expression recognition attempt to recognize a small set of the
prototypic expressions such as happy, surprise, anger, sad, disgust
and fear. However the most of the human emotions are
communicated by changes in one or two of discrete features. In this
paper, we develop a facial expressions synthesis system, based on the
facial characteristic points (FCP's) tracking in the frontal image
sequences. Selected FCP's are automatically tracked using a crosscorrelation
based optical flow. The proposed synthesis system uses a
simple deformable facial features model with a few set of control
points that can be tracked in original facial image sequences.
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: Single crystals of Magnesium alloys such as pure Mg,
Mg-1Zn-0.5Y, Mg-0.1Y, and Mg-0.1Ce alloys were successfully
fabricated in this study by employing the modified Bridgman method.
To determine the exact orientation of crystals, pole figure
measurement using X-ray diffraction were carried out on each single
crystal. Hardness and compression tests were conducted followed by
subsequent recrysatllization annealing. Recrystallization kinetics of
Mg alloy single crystals has been investigated. Fabricated single
crystals were cut into rectangular shaped specimen and solution
treated at 400oC for 24 hrs, and then deformed in compression mode
by 30% reduction. Annealing treatment for recrystallization has been
conducted on these cold-rolled plates at temperatures of 300oC for
various times from 1 to 20 mins. The microstructure observation and
hardness measurement conducted on the recrystallized specimens
revealed that static recrystallization of ternary alloy single crystal was
very slow, while recrystallization behavior of binary alloy single
crystals appeared to be very fast.
Abstract: Bumpers play an important role in preventing the
impact energy from being transferred to the automobile and
passengers. Saving the impact energy in the bumper to be released in
the environment reduces the damages of the automobile and
passengers.
The goal of this paper is to design a bumper with minimum weight
by employing the Glass Material Thermoplastic (GMT) materials.
This bumper either absorbs the impact energy with its deformation or
transfers it perpendicular to the impact direction.
To reach this aim, a mechanism is designed to convert about 80%
of the kinetic impact energy to the spring potential energy and
release it to the environment in the low impact velocity according to
American standard1. In addition, since the residual kinetic energy
will be damped with the infinitesimal elastic deformation of the
bumper elements, the passengers will not sense any impact. It should
be noted that in this paper, modeling, solving and result-s analysis
are done in CATIA, LS-DYNA and ANSYS V8.0 software
respectively.
Abstract: Using strength Pulse Electrical Field (PEF) in food
industries is a non-thermal process that can deactivate
microorganisms and increase penetration in plant and animals tissues
without serious impact on food taste and quality. In this paper designing and fabricating of a PEF generator has been presented. Pulse generation methods have been surveyed and the best of them
selected. The equipment by controller set can generate square pulse with adjustable parameters such as amplitude 1-5kV, frequency 0.1-10Hz, pulse width 10-100s, and duty cycle 0-100%. Setting the number of pulses, and presenting the output voltage and current
waveforms on the oscilloscope screen are another advantages of this
equipment. Finally, some food samples were tested that yielded the satisfactory results. PEF applying had considerable effects on potato, banana and purple cabbage. It caused increase Brix factor from 0.05
to 0.15 in potato solution. It is also so effective in extraction color material from purple cabbage. In the last experiment effects of PEF
voltages on color extraction of saffron scum were surveyed (about 6% increasing yield).
Abstract: Overloading is a technique to accommodate more
number of users than the spreading factor N. This is a bandwidth
efficient scheme to increase the number users in a fixed bandwidth.
One of the efficient schemes to overload a CDMA system is to use
two sets of orthogonal signal waveforms (O/O). The first set is
assigned to the N users and the second set is assigned to the
additional M users. An iterative interference cancellation technique is
used to cancel interference between the two sets of users. In this
paper, the performance of an overloading scheme in which the first N
users are assigned Walsh-Hadamard orthogonal codes and extra users
are assigned the same WH codes but overlaid by a fixed (quasi) bent
sequence [11] is evaluated. This particular scheme is called Quasi-
Orthogonal Sequence (QOS) O/O scheme, which is a part of
cdma2000 standard [12] to provide overloading in the downlink
using single user detector. QOS scheme are balance O/O scheme,
where the correlation between any set-1 and set-2 users are
equalized. The allowable overload of this scheme is investigated in
the uplink on an AWGN and Rayleigh fading channels, so that the
uncoded performance with iterative multistage interference
cancellation detector remains close to the single user bound. It is
shown that this scheme provides 19% and 11% overloading with
SDIC technique for N= 16 and 64 respectively, with an SNR
degradation of less than 0.35 dB as compared to single user bound at
a BER of 0.00001. But on a Rayleigh fading channel, the channel
overloading is 45% (29 extra users) at a BER of 0.0005, with an SNR
degradation of about 1 dB as compared to single user performance
for N=64. This is a significant amount of channel overloading on a
Rayleigh fading channel.
Abstract: In accordance with environmental impacts contended in Kyoto Protocol, the study aims to explore the different administrative and non-administrative measurements that industrial countries, such as America, German, Japan, Korea, Holland and British take to face with the increasing Global Warming phenomena. By large, these measurements consist of versatile dimensions, including of education and advocating, economical instruments, research developments and instances, restricted instruments, voluntary contacts, exchangeable permit for carbon-release and public investments. The results of discussion for the study are as follows: both economical impacts as well as reformations for nations that are affected via Kyoto Protocol, and human testifying for variables of global surroundings in the age of Kyoto Protocol.
Abstract: Circular knitting machine makes the fabric with more than two knitting tools. Variation of yarn tension between different knitting tools causes different loop length of stitches duration knitting process. In this research, a new intelligent method is applied to control loop length of stitches in various tools based on ideal shape of stitches and real angle of stitches direction while different loop length of stitches causes stitches deformation and deviation those of angle. To measure deviation of stitch direction against variation of tensions, image processing technique was applied to pictures of different fabrics with constant front light. After that, the rate of deformation is translated to needed compensation of loop length cam degree to cure stitches deformation. A fuzzy control algorithm was applied to loop length modification in knitting tools. The presented method was experienced for different knitted fabrics of various structures and yarns. The results show that presented method is useable for control of loop length variation between different knitting tools based on stitch deformation for various knitted fabrics with different fabric structures, densities and yarn types.
Abstract: The tensile properties of Mg-3%Al nanocrystalline
alloys were investigated at different test environment. Bulk
nanocrystalline samples of these alloy was successfully prepared by
mechanical alloying (MA) followed by cold compaction, sintering,
and hot extrusion process. The crystal size of the consolidated milled
sample was calculated by X-Ray line profile analysis. The
deformation mechanism and microstructural characteristic at
different test condition was discussed extensively. At room
temperature, relatively lower value of activation volume (AV) and
higher value of strain rate sensitivity (SRS) suggests that new rate
controlling mechanism accommodating plastic flow in the present
nanocrystalline sample. The deformation behavior and the
microstructural character of the present samples were discussed in
details.
Abstract: Constant amplitude fatigue crack growth (FCG) tests
were performed on dissimilar metal welded plates of Type 316L
Stainless Steel (SS) and IS 2062 Grade A Carbon steel (CS). The
plates were welded by TIG welding using SS E309 as electrode. FCG
tests were carried on the Side Edge Notch Tension (SENT)
specimens of 5 mm thickness, with crack initiator (notch) at base
metal region (BM), weld metal region (WM) and heat affected zones
(HAZ). The tests were performed at a test frequency of 10 Hz and at
load ratios (R) of 0.1 & 0.6. FCG rate was found to increase with
stress ratio for weld metals and base metals, where as in case of
HAZ, FCG rates were almost equal at high ΔK. FCG rate of HAZ of
stainless steel was found to be lowest at low and high ΔK. At
intermediate ΔK, WM showed the lowest FCG rate. CS showed
higher crack growth rate at all ΔK. However, the scatter band of data
was found to be narrow. Fracture toughness (Kc) was found to vary
in different locations of weldments. Kc was found lowest for the
weldment and highest for HAZ of stainless steel. A novel method of
characterizing the FCG behavior using an Infrared thermography
(IRT) camera was attempted. By monitoring the temperature rise at
the fast moving crack tip region, the amount of plastic deformation
was estimated.
Abstract: DC-DC converters are widely used in regulated switched mode power supplies and in DC motor drive applications. There are several sources of unwanted nonlinearity in practical power converters. In addition, their operation is characterized by switching that gives birth to a variety of nonlinear dynamics. DC-DC buck and boost converters controlled by pulse-width modulation (PWM) have been simulated. The voltage waveforms and attractors obtained from the circuit simulation have been studied. With the onset of instability, the phenomenon of subharmonic oscillations, quasi-periodicity, bifurcations, and chaos have been observed. This paper is mainly motivated by potential contributions of chaos theory in the design, analysis and control of power converters, in particular and power electronics circuits, in general.
Abstract: Aluminum/Copper clad sheet has been fabricated using
asymmetric extrusion method, which caused severe shear deformation
between Al and Cu plate to easily bond to each other. Interfacial
microstructure and mechanical properties of Al/Cu clad were studied
by scanning electron microscope equipped with energy dispersive
X-ray detector, micro-hardness, and tension tests. The asymmetric
extrusion bonding was very effective to provide a good interface for
atoms diffusion during subsequent annealing. The strength of bonding
was higher with the increasing extrusion ratio.
Abstract: The frontal area in the brain is known to be involved in
behavioral judgement. Because a Kanji character can be discriminated
visually and linguistically from other characters, in Kanji character
discrimination, we hypothesized that frontal event-related potential
(ERP) waveforms reflect two discrimination processes in separate
time periods: one based on visual analysis and the other based
on lexcical access. To examine this hypothesis, we recorded ERPs
while performing a Kanji lexical decision task. In this task, either a
known Kanji character, an unknown Kanji character or a symbol was
presented and the subject had to report if the presented character was
a known Kanji character for the subject or not. The same response
was required for unknown Kanji trials and symbol trials. As a preprocessing
of signals, we examined the performance of a method
using independent component analysis for artifact rejection and found
it was effective. Therefore we used it. In the ERP results, there
were two time periods in which the frontal ERP wavefoms were
significantly different betweeen the unknown Kanji trials and the
symbol trials: around 170ms and around 300ms after stimulus onset.
This result supported our hypothesis. In addition, the result suggests
that Kanji character lexical access may be fully completed by around
260ms after stimulus onset.
Abstract: Kazakhstan attaches the great importance to
cooperation with European countries within the framework of
multilateral security organizations such as NATO. Cooperation of
Kazakhstan with the NATO is a prominent aspect of strengthening of
regional security of republic. It covers a wide spectrum of areas, such
as reform of sector of defense and security, military operative
compatibility of armed forces of NATO member-countries and
Kazakhstan, civil emergency planning and scientific cooperation. The
cooperation between Kazakhstan and NATO is based on the mutual
interests of neighboring republics in the region so that the existing
forms of cooperation between Kazakhstan and NATO will not be
negatively perceived both in Asia as well as among CIS countries.
Kazakhstan tailors its participation in the PfP programme through an
annual Individual Partnership Programme, selecting those activities
that will help achieve the goals it has set in the IPAP. Level of
cooperation within the limits of PfP essentially differs on each
republic. Cooperation with Kazakhstan progressed most of all since
has been signed IPAP from the NATO
Abstract: This paper discusses a new model of Islamic code of
ethics for directors. Several corporate scandals and local (example
Transmile and Megan Media) and overseas corporate (example
Parmalat and Enron) collapses show that the current corporate
governance and regulatory reform are unable to prevent these events
from recurring. Arguably, the code of ethics for directors is under
research and the current code of ethics only concentrates on binding
the work of the employee of the organization as a whole, without
specifically putting direct attention to the directors, the group of
people responsible for the performance of the company. This study
used a semi-structured interview survey of well-known Islamic
scholars such as the Mufti to develop the model. It is expected that
the outcome of the research is a comprehensive model of code of
ethics based on the Islamic principles that can be applied and used by
the company to construct a code of ethics for their directors.
Abstract: The results from experimental research of deformation
by upsetting and die forging of lead specimens wit controlled impact
are presented. Laboratory setup for conducting the investigations,
which uses cold rocket engine operated with compressed air, is
described. The results show that when using controlled impact is
achieving greater plastic deformation and consumes less impact
energy than at ordinary impact deformation process.
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The analysis is carried out using Hamilton's principle. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of free-free and clamped-clamped boundary conditions.
Abstract: When the characteristic length of an elastic solid is
down to the nanometer level, its deformation behavior becomes size
dependent. Surface energy /surface stress have recently been applied
to explain such dependency. In this paper, the effect of
strain-independent surface stress on the deformation of an isotropic
elastic solid containing a nanosized elliptical hole is studied by the
finite element method. Two loading cases are considered, in the first
case, hoop stress along the rim of the elliptical hole induced by pure
surface stress is studied, in the second case, hoop stress around the
elliptical opening under combined remote tension and surface stress is
investigated. It has been shown that positive surface stress induces
compressive hoop stress along the hole, and negative surface stress has
opposite effect, maximum hoop stress occurs near the major semi-axes
of the ellipse. Under combined loading of remote tension and surface
stress, stress concentration around the hole can be either intensified or
weakened depending on the sign of the surface stress.
Abstract: The paper discuses the effect of initial stresses on the reflection coefficients of plane waves in a dissipative medium. Basic governing equations are formulated in context of Biot's incremental deformation theory. These governing equations are solved analytically to obtain the dimensional phase velocities of plane waves propagating in plane of symmetry. Closed-form expressions for the reflection coefficients of P and SV waves- incident at the free surface of an initially stressed dissipative medium are obtained. Numerical computations, using these expressions, are carried out for a particular model. Computations made with the results predicted in presence and absence of the initial stresses and the results have been shown graphically. The study shows that the presence of compressive initial stresses increases the velocity of longitudinal wave (P-wave) but diminishes that of transverse wave (SV-wave). Also the numerical results presented indicate that initial stresses and dissipation might affect the reflection coefficients significantly.
Abstract: The governing differential equations of laminated
plate utilizing trigonometric shear deformation theory are derived
using energy approach. The governing differential equations
discretized by different radial basis functions are used to predict the
free vibration behavior of symmetric laminated composite plates.
Effect of orthotropy and span to thickness ratio on frequency
parameter of simply supported laminated plate is presented.
Numerical results show the accuracy and good convergence of radial
basis functions.