Abstract: The software industry has been considered a critical
infrastructure for any nation. Several studies have indicated that
national competitiveness increasingly depends upon Information and
Communication Technology (ICT), and software is one of the major
components of ICT, important for both large and small enterprises.
Even though there has been strong growth in the software industry in
Thailand, the industry has faced many challenges and problems that
need to be resolved. For example, the amount of pirated software has
been rising, and Thailand still has a large gap in the digital divide.
Additionally, the adoption among SMEs has been slow. This paper
investigates various issues in the software industry in Thailand, using
information acquired through analysis of secondary sources,
observation, and focus groups. The results of this study can be used
as “lessons learned" for the development of the software industry in
any developing country.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: In this paper, based on the past project cost and time
performance, a model for forecasting project cost performance is
developed. This study presents a probabilistic project control concept
to assure an acceptable forecast of project cost performance. In this
concept project activities are classified into sub-groups entitled
control accounts. Then obtain the Stochastic S-Curve (SS-Curve), for
each sub-group and the project SS-Curve is obtained by summing
sub-groups- SS-Curves. In this model, project cost uncertainties are
considered through Beta distribution functions of the project
activities costs required to complete the project at every selected time
sections through project accomplishment, which are extracted from a
variety of sources. Based on this model, after a percentage of the
project progress, the project performance is measured via Earned
Value Management to adjust the primary cost probability distribution
functions. Then, accordingly the future project cost performance is
predicted by using the Monte-Carlo simulation method.
Abstract: This paper and its companion (Part 2) deal with
modeling and optimization of two NP-hard problems in production
planning of flexible manufacturing system (FMS), part type selection
problem and loading problem. The part type selection problem and
the loading problem are strongly related and heavily influence the
system-s efficiency and productivity. The complexity of the problems
is harder when flexibilities of operations such as the possibility of
operation processed on alternative machines with alternative tools are
considered. These problems have been modeled and solved
simultaneously by using real coded genetic algorithms (RCGA)
which uses an array of real numbers as chromosome representation.
These real numbers can be converted into part type sequence and
machines that are used to process the part types. This first part of the
papers focuses on the modeling of the problems and discussing how
the novel chromosome representation can be applied to solve the
problems. The second part will discuss the effectiveness of the
RCGA to solve various test bed problems.
Abstract: The paper presents an optimization study based on
genetic algorithms (GA-s) for a radio-frequency applicator used in
heating dielectric band products. The weakly coupled electro-thermal
problem is analyzed using 2D-FEM. The design variables in the
optimization process are: the voltage of a supplementary “guard"
electrode and six geometric parameters of the applicator. Two
objective functions are used: temperature uniformity and total active
power absorbed by the dielectric. Both mono-objective and multiobjective
formulations are implemented in GA optimization.
Abstract: Rotation or tilt present in an image capture by digital
means can be detected and corrected using Artificial Neural Network
(ANN) for application with a Face Recognition System (FRS). Principal
Component Analysis (PCA) features of faces at different angles
are used to train an ANN which detects the rotation for an input image
and corrected using a set of operations implemented using another
system based on ANN. The work also deals with the recognition
of human faces with features from the foreheads, eyes, nose and
mouths as decision support entities of the system configured using
a Generalized Feed Forward Artificial Neural Network (GFFANN).
These features are combined to provide a reinforced decision for
verification of a person-s identity despite illumination variations. The
complete system performing facial image rotation detection, correction
and recognition using re-enforced decision support provides a
success rate in the higher 90s.
Abstract: Image restoration involves elimination of noise. Filtering techniques were adopted so far to restore images since last five decades. In this paper, we consider the problem of image restoration degraded by a blur function and corrupted by random noise. A method for reducing additive noise in images by explicit analysis of local image statistics is introduced and compared to other noise reduction methods. The proposed method, which makes use of an a priori noise model, has been evaluated on various types of images. Bayesian based algorithms and technique of image processing have been described and substantiated with experimentation using MATLAB.
Abstract: Physiological activity of the pineal gland with specific
responses in the reproductive territory may be interpreted by
monitoring the process parameters used in poultry practice in
different age batches of laying hens. As biological material were
used 105 laying hens, clinically healthy, belonging to ALBO SL-
2000 hybrid, raised on ground, from which blood samples were taken
at the age of 12 and 28 weeks. The haematological examinations
were concerned to obtain the total number of erythrocytes and
leukocytes and the main erythrocyte constant (RBC, PCV, MCV,
MCH, MCHC and WBC). The results allow the interpretation of the
reproductive status through the dynamics of the presented values.
Abstract: This article proposes modeling, simulation and
kinematic and workspace analysis of a spatial cable suspended robot
as incompletely Restrained Positioning Mechanism (IRPM). These
types of robots have six cables equal to the number of degrees of
freedom. After modeling, the kinds of workspace are defined then an
statically reachable combined workspace for different geometric
structures of fixed and moving platform is obtained. This workspace
is defined as the situations of reference point of the moving platform
(center of mass) which under external forces such as weight and with
ignorance of inertial effects, the moving platform should be in static
equilibrium under conditions that length of all cables must not be
exceeded from the maximum value and all of cables must be at
tension (they must have non-negative tension forces). Then the effect
of various parameters such as the size of moving platform, the size of
fixed platform, geometric configuration of robots, magnitude of
applied forces and moments to moving platform on workspace of
these robots with different geometric configuration are investigated.
Obtained results should be effective in employing these robots under
different conditions of applied wrench for increasing the workspace
volume.
Abstract: Recently research on human wayfinding has focused
mainly on mental representations rather than processes of
wayfinding. The objective of this paper is to demonstrate the
rationality behind applying multi-agent simulation paradigm to the
modeling of rescuer team wayfinding in order to develop
computational theory of perceptual wayfinding in crisis situations
using image schemata and affordances, which explains how people
find a specific destination in an unfamiliar building such as a
hospital. The hypothesis of this paper is that successful navigation is
possible if the agents are able to make the correct decision through
well-defined cues in critical cases, so the design of the building
signage is evaluated through the multi-agent-based simulation. In
addition, a special case of wayfinding in a building, finding one-s
way through three hospitals, is used to demonstrate the model.
Thereby, total rescue time for rescue operation during building fire is
computed. This paper discuses the computed rescue time for various
signage localization and provides experimental result for
optimization of building signage design. Therefore the most
appropriate signage design resulted in the shortest total rescue time in
various situations.
Abstract: In this paper a numerical algorithm is described for solving the boundary value problem associated with axisymmetric, inviscid, incompressible, rotational (and irrotational) flow in order to obtain duct wall shapes from prescribed wall velocity distributions. The governing equations are formulated in terms of the stream function ψ (x,y)and the function φ (x,y)as independent variables where for irrotational flow φ (x,y)can be recognized as the velocity potential function, for rotational flow φ (x,y)ceases being the velocity potential function but does remain orthogonal to the stream lines. A numerical method based on the finite difference scheme on a uniform mesh is employed. The technique described is capable of tackling the so-called inverse problem where the velocity wall distributions are prescribed from which the duct wall shape is calculated, as well as the direct problem where the velocity distribution on the duct walls are calculated from prescribed duct geometries. The two different cases as outlined in this paper are in fact boundary value problems with Neumann and Dirichlet boundary conditions respectively. Even though both approaches are discussed, only numerical results for the case of the Dirichlet boundary conditions are given. A downstream condition is prescribed such that cylindrical flow, that is flow which is independent of the axial coordinate, exists.
Abstract: Sesame is one of the oldest and most important oil
crops as main crop and second crop agriculture. This study was
carried out to determine the effects of different inter- and intra-row
spacings on the yield and yield components on second crop sesame;
was set up in Antalya West Mediterranean Agricultural Research
Institue in 2009. Muganlı 57 sesame cultivar was used as plant
material. The field experiment was set up in a split plot design and
row spacings (30, 40, 50, 60 and 70 cm) were assigned to the main
plots and and intra-row spacings (5, 10, 20 and 30 cm) were assigned
to the subplots. Seed yield, oil ratio, oil yield, protein ratio and
protein yield were investigated. In general, wided inter row spacings
and intra-row spacings, resulted in decreased seed yield, oil yield and
protein yield. The highest seed yield, oil yield and protein yield
(respectively, 1115.0 kg ha-1, 551.3 kg ha-1, 224.7 kg ha-1) were
obtained from 30x5 cm plant density while the lowest seed yield, oil
yield and protein yield (respectively, 677.0 kg ha-1, 327.0 kg ha-1,
130.0 kg ha-1) were recorded from 70x30 cm plant density. As a
result, in terms of oil yield for second crop sesame agriculture, 30 cm
row spacing, and 5 cm intra row spacing are the most suitable plant
densities.
Abstract: the intension in this work is to investigate the effect of
different bending manifold pipes on engine performance for different
engine speed. Power, Torque, and BSFC were calculated and
presented to show the effect of varying bending pipes angles on them
for all cases considered. A special program used to carry out the
calculations. A simulation model for 4-cylinders spark ignition
engine with turbocharger has been built and calculated. The analysis
of the results shows that for 120o angle the torque increases about
40% at 3000 rpm and 25% at 4000 rpm without changing in fuel
consumption. For 90o angle the increment in torque is about 10 %.
For the same bending angle the increment in brake power is around
40% at 3000 rpm and 25% at 4000 rpm. The increment in fuel
consumption is about 12% for 60o and 30% for 90o between (6000-
7000) rpm.
Abstract: The automatic transmission (AT) is one of the most
important components of many automobile transmission systems. The
shift quality has a significant influence on the ride comfort of the
vehicle. During the AT shift process, the joint elements such as the
clutch and bands engage or disengage, linking sets of gears to create a
fixed gear ratio. Since these ratios differ between gears in a fixed gear
ratio transmission, the motion of the vehicle could change suddenly
during the shift process if the joint elements are engaged or disengaged
inappropriately, additionally impacting the entire transmission system
and increasing the temperature of connect elements.The objective was
to establish a system model for an AT powertrain using
Matlab/Simulink. This paper further analyses the effect of varying
hydraulic pressure and the associated impact on shift quality during
both engagment and disengagement of the joint elements, proving that
shift quality improvements could be achieved with appropriate
hydraulic pressure control.
Abstract: This research focuses on the effect of weight
percentage variation and size variation of MgFeSi added,
gating system design and reaction chamber design on inmold
process. By using inmold process, well-known problem of
fading is avoided because the liquid iron reacts with
magnesium in the mold and not, as usual, in the ladle. During
the pouring operation, liquid metal passes through the
chamber containing the magnesium, where the reaction of the
metal with magnesium proceeds in the absence of atmospheric
oxygen [1].In this paper, the results of microstructural
characteristic of ductile iron on this parameters are mentioned.
The mechanisms of the inmold process are also described [2].
The data obtained from this research will assist in producing
the vehicle parts and other machinery parts for different
industrial zones and government industries and in transferring
the technology to all industrial zones in Myanmar. Therefore,
the inmold technology offers many advantages over traditional
treatment methods both from a technical and environmental,
as well as an economical point of view. The main objective of
this research is to produce ductile iron castings in all industrial
sectors in Myanmar more easily with lower costs. It will also
assist the sharing of knowledge and experience related to the
ductile iron production.
Abstract: Validity is an overriding consideration in language testing. If a test score is intended for a particular purpose, this must be supported through empirical evidence. This article addresses the validity of a multiple-choice achievement test (MCT). The test is administered at the end of each semester to decide about students' mastery of a course in general English. To provide empirical evidence pertaining to the validity of this test, two criterion measures were used. In so doing, a Cloze test and a C-test which are reported to gauge general English proficiency were utilized. The results of analyses show that there is a statistically significant correlation among participants' scores on the MCT, Cloze, and Ctest. Drawing on the findings of the study, it can be cautiously deduced that these tests measure the same underlying trait. However, allowing for the limitations of using criterion measures to validate tests, we cannot make any absolute claim as to the validity of this MCT test.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: Aldehydes as secondary lipid oxidation products are highly specific to the oxidative degradation of particular polyunsaturated fatty acids present in foods. Gas chromatographic analysis of those volatile compounds has been widely used for monitoring of the deterioration of food products. Developed static headspace gas chromatography method using flame ionization detector (SHS GC FID) was applied to monitor the aldehydes present in processed foods such as bakery, meat and confectionary products.
Five selected aldehydes were determined in samples without any sample preparation, except grinding for bakery and meat products. SHS–GC analysis allows the separation of propanal, pentanal, hexanal, heptanal and octanal, within 15min. Aldehydes were quantified in fresh and stored samples, and the obtained range of aldehydes in crackers was 1.62±0.05 – 9.95±0.05mg/kg, in sausages 6.62±0.46 – 39.16±0.39mg/kg; and in cocoa spread cream 0.48±0.01 – 1.13±0.02mg/kg. Referring to the obtained results, the following can be concluded, proposed method is suitable for different types of samples, content of aldehydes varies depending on the type of a sample, and differs in fresh and stored samples of the same type.
Abstract: To offer a large variety of products while maintaining
low costs, high speed, and high quality in a mass customization
product development environment, platform based product
development has much benefit and usefulness in many industry fields.
This paper proposes a product configuration strategy by similarity
measure, incorporating the knowledge engineering principles such as
product information model, ontology engineering, and formal concept
analysis.
Abstract: This paper presents a comparative analysis of a new
unsupervised PCA-based technique for steel plates texture segmentation
towards defect detection. The proposed scheme called Variance
Based Component Analysis or VBCA employs PCA for feature
extraction, applies a feature reduction algorithm based on variance of
eigenpictures and classifies the pixels as defective and normal. While
the classic PCA uses a clusterer like Kmeans for pixel clustering,
VBCA employs thresholding and some post processing operations to
label pixels as defective and normal. The experimental results show
that proposed algorithm called VBCA is 12.46% more accurate and
78.85% faster than the classic PCA.