Abstract: The textile industry produces highly coloured
effluents containing polar and non-polar compounds. The textile mill
run by the Assam Polyester Co-operative Society Limited (APOL) is
situated at Rangia, about 55 km from Guwahati (26011' N, 91047' E)
in the northern bank of the river Brahmaputra, Assam (India). This
unit was commissioned in June 1988 and started commercial
production in November 1988. The installed capacity of the weaving
unit was 8000 m/day and that of the processing unit was 20,000
m/day. The mill has its own dyeing unit with a capacity of 1500-2000
kg/day. The western side of the mill consists of vast agricultural land
and the far northern and southern side of the mill has scattered human
population. The eastern side of the mill has a major road for
thoroughfare. The mill releases its effluents into the agricultural land
in the western side of the mill. The present study was undertaken to
assess the impact of the textile mill on surface soil quality in and
around the mill with particular reference to Cr, Mn, Ni and Zn.
Surface soil samples, collected along different directions at 200, 500
and 1000 m were digested and the metals were estimated with
Atomic Absorption Spectrophotometer. The metals were found in the
range of: Cr 50.9 – 105.0 mg kg-1, Mn 19.2- 78.6 mg kg-1, Ni 41.9 –
50.6 mg kg-1 and Zn 187.8 – 1095.8 mg kg-1. The study reveals
enrichment of Cr, Mn, Ni and Zn in the soil near the textile mill.
Abstract: The cup method is applied for the measurement of water vapor transport properties of porous materials worldwide. However, in practical applications the experimental results are often used without taking into account some secondary effects which can play an important role under specific conditions. In this paper, the effect of temperature on water vapor transport properties of cellular concrete is studied, together with the influence of sample thickness. At first, the bulk density, matrix density, total open porosity and sorption and desorption isotherms are measured for material characterization purposes. Then, the steady state cup method is used for determination of water vapor transport properties, whereas the measurements are performed at several temperatures and for three different sample thicknesses.
Abstract: Free Hemoglobin promotes the accumulation of
hydroxyl radicals by the heme iron, which can react with endogenous
hydrogen peroxide to produce free radicals which may cause severe
oxidative cell damage. Haptoglobin binds to Hemoglobin strongly
and Haptoglobin-Hemoglobin binding is irreversible. Peroxidase
activity of Haptoglobin(2-2)-Hemoglobin complex was assayed by
following increase of absorption of produced tetraguaiacol as the
second substrate of Haptoglobin-Hemoglobin complex at 470 nm and
42°C by UV-Vis spectrophotometer. The results have shown that
peroxidase activity of Haptoglobin(2-2)-Hemoglobin complex is
modulated via homotropic effect of hydrogen peroxide as allostric
substrate. On the other hand antioxidant property of Haptoglobin(2-
2)-Hemoglobin was increased via heterotropic effect of the two drugs
(especially ampicillin) on peroxidase activity of the complex. Both
drugs also have mild effect on quality of homotropic property of
peroxidase activity of Haptoglobin(2-2)-Hemoglobin complex.
Therefore, in vitro studies show that the two drugs may help Hp-Hb
complex to remove hydrogen peroxide from serum at pathologic
temperature ature (42 C).
Abstract: Durian husk (DH), a fruit waste, was studied for its ability to remove Basic blue 3 (BB3) from aqueous solutions. Batch kinetic studies were carried out to study the sorption characteristics under various experimental conditions. The optimum pH for the dye removal occurred in the pH range of 3-10. Sorption was found to be concentration and agitation dependent. The kinetics of dye sorption fitted a pseudo-second order rate expression. Both Langmuir and Freundlich models appeared to provide reasonable fittings for the sorption data of BB3 on durian husk. Maximum sorption capacity calculated from the Langmuir model is 49.50 mg g-1.
Abstract: The Iranian bentonite was first characterized by
Scanning Electron Microscopy (SEM), Inductively Coupled Plasma
mass spectrometry (ICP-MS), X-ray fluorescence (XRF), X-ray
Diffraction (XRD) and BET. The bentonite was then treated
thermally between 150°C-250°C at 15min, 45min and 90min and
also was activated chemically with different concentration of
sulphuric acid (3N, 5N and 10N). Although the results of thermal
activated-bentonite didn-t show any considerable changes in specific
surface area and Cation Exchange Capacity (CEC), but the results of
chemical treated bentonite demonstrated that such properties have
been improved by acid activation process.
Abstract: Photo-crosslinked rice starch-based biodegradable
films were prepared by casting film-solution on leveled trays and
ultra violet (UV) irradiation was applied for 10 minute. The effect of
the content (3%, 6% and 9 wt. %)of photosensitiser (sodium
benzoate) on mechanical properties, water vapor permeability (WVP)
and structural properties of rice starch films were investigated. The
tensile strength increased while elongation at break and water
resistance properties of rice starch films decreased with addition and
increasing content of photosensitiser. The % crystallinity of rice
starch films were decreased when the content of photosensitiser
increased and UV were applied. The results showed that the
carboxylate group band of sodium benzoate was found in the FTIR
spectrum of rice starch films and found that incorporation of 6% of
photosensitiser into the films showed a higher absorption band of
resulted films. This result pointed out the highest interaction between
starch molecules was occurred.
Abstract: As application of re-activation of backside on power
device Insulated Gate Bipolar Transistor (IGBT), laser annealing was
employed to irradiate amorphous silicon substrate, and resistivities
were measured using four point probe measurement. For annealing
the amorphous silicon two lasers were used at wavelength of visible
green (532 nm) together with Infrared (793 nm). While the green
laser efficiently increased temperature at top surface the Infrared
laser reached more deep inside and was effective for melting the
top surface. A finite element method was employed to evaluate time
dependent thermal distribution in silicon substrate.
Abstract: In this study, we sought to investigate the mercury
removal efficiency of manganese oxides from natural gas. The
fundamental studies on mercury removal with manganese oxides
sorbents were carried out in a laboratory scale fixed bed reactor at 30
°C with a mixture of methane (20%) and nitrogen gas laden with 4.8
ppb of elemental mercury. Manganese oxides with varying surface
area and crystalline phase were prepared by conventional precipitation
method in this study. The effects of surface area, crystallinity and
other metal oxides on mercury removal efficiency were investigated.
Effect of Ag impregnation on mercury removal efficiency was also
investigated. Ag supported on metal oxide such titania and zirconia as
reference materials were also used in this study for comparison. The
characteristics of mercury removal reaction with manganese oxide
was investigated using a temperature programmed desorption (TPD)
technique.
Manganese oxides showed very high Hg removal activity (about
73-93% Hg removal) for first time use. Surface area of the manganese
oxide samples decreased after heat-treatment and resulted in complete
loss of Hg removal ability for repeated use after Hg desorption in the
case of amorphous MnO2, and 75% loss of the initial Hg removal
activity for the crystalline MnO2. Mercury desorption efficiency of
crystalline MnO2 was very low (37%) for first time use and high (98%)
after second time use. Residual potassium content in MnO2 may have
some effect on the thermal stability of the adsorbed Hg species.
Desorption of Hg from manganese oxides occurs at much higher
temperatures (with a peak at 400 °C) than Ag/TiO2 or Ag/ZrO2.
Mercury may be captured on manganese oxides in the form of mercury
manganese oxide.
Abstract: Thermoplastic starch, polylactic acid glycerol and
maleic anhydride (MA) were compounded with natural
montmorillonite (MMT) through a twin screw extruder to investigate
the effects of different loading of MMT on structure, thermal and
absorption behavior of the nanocomposites. X-ray diffraction analysis
(XRD) showed that sample with MMT loading 4phr exhibited
exfoliated structure while sample that contained MMT 8 phr
exhibited intercalated structure. FESEM images showed big lump
when MMT loading was at 8 phr. The thermal properties were
characterized by using differential scanning calorimeter (DSC). The
results showed that MMT increased melting temperature and
crystallization temperature of matrix but reduction in glass transition
temperature was observed Meanwhile the addition of MMT has
improved the water barrier property. The nanosize MMT particle is
also able to block a tortuous pathway for water to enter the starch
chain, thus reducing the water uptake and improved the physical
barrier of nanocomposite.
Abstract: In a transcutanious inductive coupling of a biomedical
implant, a new formula is given for the study of the Radio Frequency
power attenuation by the biological tissue. The loss of the signal
power is related to its interaction with the biological tissue and the
composition of this one. A confrontation with the practical
measurements done with a synthetic muscle into a Faraday cage,
allowed a checking of the obtained theoretical results. The
supply/data transfer systems used in the case of biomedical implants,
can be well dimensioned by taking in account this type of power
attenuation.
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: Ammonia nitrogen is one of the most hazardous
water pollutants, discharging into water receptors through industrial
effluents. Negative environmental impacts of such chemical species
in hydrosphere include accelerated eutrophication, water toxicity and
harming the aquatics. Natural zeolite clinoptilolite has very high
selectivity & capacity for ammonium cation sorption. It occurs in
high abundances and rich mines of this zeolite exist in different parts
of Iran and thus are available more cheaply and with different sizing.
The aim of this study is to investigate ammonia nitrogen removal
over this natural sorbent from real samples of high polluted
wastewater discharging from a fertilizer producing plant. The
experimental results showed that this natural sorbent without even
any pre treatment system & with the same particle size available in
Iranian markets has still high capability & selectivity in ammonia
nitrogen removal both in batch and continuous tests.
Abstract: Activated carbon was prepared from agricultural waste “almond (Prunus amygdalus) nut shells" by chemical activation with phosphoric acid as an activating agent at 450 °C for 24 hr soaking time. The physical and chemical properties were analyzed. The adsorption of chromium VI from aqueous solution on almond nut shell activated carbon (ASAC) was investigated. The adsorption process parameters pH, agitation speed, agitation time, adsorbent dose were optimized. 98% of Cr VI was sorbed at pH 2 and stirring speed 200 rpm.. Surface structure showed that ASAC has a spongy type structure showing large number of pores
Abstract: This research aimed at investigating the Cr (III), Cd
(II) and Pb (II) removal efficiencies by using the newly synthesized
metal oxides/ polyethersulfone (PES), Al2O3/PES and ZrO2/PES,
membranes from synthetic wastewater and exploring fouling
mechanisms. A Comparative study between the removal efficiencies
of Cr (III), Cd (II) and Pb (II) from synthetic and natural wastewater
by using adsorption onto agricultural by products and the newly
synthesized Al2O3/PES and ZrO2/PES membranes was conducted to
assess the advantages and limitations of using the metal oxides/PES
membranes for heavy metals removal. The results showed that about
99 % and 88 % removal efficiencies were achieved by the tested
membranes for Pb (II) and Cr (III), respectively.
Abstract: The resource-based view of the firm regards
knowledge as one of the most important organizational assets and a
key strategic resource that contributes unique value to organizations.
The acquisition, absorption and internalization of external
knowledge are central to an organization-s innovative capabilities.
This ability to evaluate, acquire and integrate new knowledge from
its environment is referred to as a firm-s absorptive capacity (AC).
This research in progress paper explores the link between interorganizational
Social Networks (SNs) and a firm-s Absorptive
Capacity (AC). Based on an in-depth literature survey of both
concepts, four propositions are proposed that explain the link
between AC and SNs. These propositions suggest that SNs are key
to a firm-s AC. A qualitative research method is proposed to test the
set of propositions in the next stage of this research.
Abstract: Nonspecific protein adsorption generally occurs on
any solid surfaces and usually has adverse consequences. Adsorption
of proteins onto a solid surface is believed to be the initial and
controlling step in biofouling. Surfaces modified with end-tethered
poly(ethylene glycol) (PEG) have been shown to be protein-resistant
to some degree. In this study, the adsorption of β-casein and
lysozyme was performed on 6 different types of surfaces where PEG
was tethered onto stainless steel by polyethylene imine (PEI) through
either OH or NHS end groups. Protein adsorption was also performed
on the bare stainless steel surface as a control. The adsorption was
conducted at 23 °C and pH 7.2. In situ QCM-D was used to
determine PEG adsorption kinetics, plateau PEG chain densities,
protein adsorption kinetics and plateau protein adsorbed quantities.
PEG grafting density was the highest for a NHS coupled chain,
around 0.5 chains / nm2. Interestingly, lysozyme which has smaller
size than β-casein, appeared to adsorb much less mass than that of β-
casein. Overall, the surface with high PEG grafting density exhibited
a good protein rejection.
Abstract: In this work, effects of catalysts (TiO2, and Nb2O5) were investigated on the hydrogen desorption of Mg(BH4)2. LiBH4 and MgCl2 with 2:1 molar ratio were mixed by using ball milling to prepare Mg(BH4)2. The desorption behaviors were measured by thermo-volumetric apparatus. The hydrogen desorption capacity of the mixed sample milled for 2 h was 4.78 wt% with a 2-step released. The first step occurred at 214 °C and the second step appeared at 374 °C. The addition of 16 wt% Nb2O5 decreased the desorption temperature in the second step about 66 °C and increased the hydrogen desorption capacity to 4.86 wt% hydrogen. The addition of TiO2 also improved the desorption temperature in the second step and the hydrogen desorption capacity. It decreased the desorption temperature about 71°C and showed a high amount of hydrogen, 5.27 wt%, released from the mixed sample. The hydrogen absorption after desorption of Mg(BH4)2 was also studied under 9.5 MPa and 350 °C for 12 h.
Abstract: The increments of aromatic structures are widely used to monitor the degree of humification. Compost derived from mix manures mixed with agricultural wastes was studied. The compost collected at day 0, 7, 14, 21, 28, 35, 49, 77, 91, 105, and 119 was divided into 3 stages, initial stage at day 0, thermophilic stage during day 1-48, and mature stage during day 49-119. The change of highest absorptions at wavelength range between 210-235 nm during day 0- 49 implied that small molecules such as nitrates and carboxylic occurred faster than the aromatic molecules that were found at wavelength around 280 nm. The ratio of electron-transfer band at wavelength 253 nm by the benzonoid band at wavelength 230 nm (E253/E230) also gradually increased during the fermenting period indicating the presence of O-containing functional groups. This was in agreement with the shift change from aliphatic to aromatic structures as shown by the relationship with C/N and H/C ratios (r = - 0.631 and -0.717, p< 0.05) since both were decreasing. Although the amounts of humic acid (HA) were not different much during the humification process, the UV spectral deconvolution showed better qualitative characteristics to help in determining the compost quality. From this study, the compost should be used at day 49 and should not be kept longer than 3 months otherwise the quality of HA would decline regardless of the amounts of HA that might be rising. This implied that other processes, such as mineralization had an influence on the humification process changing HA-s structure and its qualities.
Abstract: In situ observation of absorption spectral change of
heptil viologen cation radical (HV+.) was performed by slab optical
waveguide (SOWG) spectroscopy utilizing indium-tin-oxide (ITO)
electrodes. Synchronizing with electrochemical techniques, we
observed the adsorption process of HV+.on the ITO electrode. In this
study, we carried out the ITO-SOWG observations using KBr aqueous
solution containing different concentration of HV to investigate the
concentration dependent spectral change. A few specific absorption
bands, which indicated HV+.existed as both monomer and dimer on
ITO electrode surface with a monolayer or a few layers deposition,
were observed in UV-visible region. The change in the peak position
of the absorption spectra from adsorption species of HV+. were
correlated with the concentration of HV as well as the electrode
potential.
Abstract: Nowadays, fluidized bed plays an important part in industry. The design of this kind of reactor requires knowing the interfacial area between two phases and this interfacial area leads to calculate the solid holdup in the bed. Consequently achieving interfacial area between gas and solid in the bed experimentally is so significant. On interfacial area measurement in fluidized bed with gas has been worked, but light transmission technique has been used less. Therefore, in the current research the possibility of using of this technique and its accuracy are investigated. Measuring, a fluidized bed was designed and the problems were averted as far as possible. By using fine solid with equal shape and diameter and installing an optical system, the absorption of light during the time of fluidization has been measured. Results indicate that this method that its validity has been proved in the gas-liquid system, by different reasons have less application in gas-solid system. One important reason could be non-uniformity in such systems.