Abstract: Liquid storage tanks have become widespread during the recent decades due to their extensive usage. Analysis of liquid containing tanks is known to be complex due to hydrodynamic force exerted on tank which makes the analysis a complex one. The objective of this research is to carry out analysis of liquid domain along with structural interaction for various geometries of circular tanks considering seismic effects. An attempt has been made to determine hydrodynamic pressure distribution on the tank wall considering impulsive and convective components of liquid mass. To get a better picture, a comparative study of Draft IS 1893 Part 2, ACI 350.3 and Eurocode 8 for Circular Shaped Tank has been performed. Further, the differences in the magnitude of shear and moment at base as obtained from static (IS 3370 IV) and dynamic (Draft IS 1892 Part 2) analysis of ground supported circular tank highlight the need for us to mature from the old code to a newer code, which is more accurate and reliable.
Abstract: In this paper, an attempt has been made to analyze the effect of wall window orientation on Daylight Illuminance Ratio (DIR) and energy saving in a building known as “SODHA BERS COMPLEX (SBC)” at Varanasi, UP, India. The building has been designed incorporating all passive concepts for thermal comfort as well daylighting concepts to maximize the use of natural daylighting for the occupants in the day to day activities. The annual average DIR and the energy saving has been estimated by using the DIR model for wall window with different orientations under clear sky condition. It has been found that for south oriented window the energy saving per square meter is more compared to the other orientations due to the higher level of solar insolation for the south window in northern hemisphere whereas energy saving potential is minimum for north oriented wall window. The energy saving potential was 26%, 81% and 51% higher for east, south and west oriented window in comparison to north oriented window. The average annual DIR has same trends of variation as the annual energy saving and it is maximum for south oriented window and minimum for north oriented window.
Abstract: The effectiveness of microchannels in enhancing heat
transfer has been demonstrated in the semiconductor industry. In
order to tap the microscale heat transfer effects into macro
geometries, overcoming the cost and technological constraints,
microscale passages were created in macro geometries machined
using conventional fabrication methods. A cylindrical insert was
placed within a pipe, and geometrical profiles were created on the
outer surface of the insert to enhance heat transfer under steady-state
single-phase liquid flow conditions. However, while heat transfer
coefficient values of above 10 kW/m2·K were achieved, the heat
transfer enhancement was accompanied by undesirable pressure drop
increment. Therefore, this study aims to address the high pressure
drop issue using Constructal theory, a universal design law for both
animate and inanimate systems. Two designs based on Constructal theory were developed to study
the effectiveness of Constructal features in reducing the pressure drop
increment as compared to parallel channels, which are commonly
found in microchannel fabrication. The hydrodynamic and heat
transfer performance for the Tree insert and Constructal fin (Cfin)
insert were studied using experimental methods, and the underlying
mechanisms were substantiated by numerical results. In technical
terms, the objective is to achieve at least comparable increment in
both heat transfer coefficient and pressure drop, if not higher
increment in the former parameter. Results show that the Tree insert improved the heat transfer
performance by more than 16 percent at low flow rates, as compared
to the Tree-parallel insert. However, the heat transfer enhancement
reduced to less than 5 percent at high Reynolds numbers. On the
other hand, the pressure drop increment stayed almost constant at 20
percent. This suggests that the Tree insert has better heat transfer
performance in the low Reynolds number region. More importantly,
the Cfin insert displayed improved heat transfer performance along
with favourable hydrodynamic performance, as compared to Cfinparallel
insert, at all flow rates in this study. At 2 L/min, the
enhancement of heat transfer was more than 30 percent, with 20
percent pressure drop increment, as compared to Cfin-parallel insert.
Furthermore, comparable increment in both heat transfer coefficient
and pressure drop was observed at 8 L/min. In other words, the Cfin
insert successfully achieved the objective of this study. Analysis of the results suggests that bifurcation of flows is
effective in reducing the increment in pressure drop relative to heat
transfer enhancement. Optimising the geometries of the Constructal
fins is therefore the potential future study in achieving a bigger stride
in energy efficiency at much lower costs.
Abstract: The objective of this research is to mitigate and prevent
the alkali silica reactivity (ASR) in highway construction projects.
ASR is a deleterious reaction initiated when the silica content of the
aggregate reacts with alkali hydroxides in cement in the presence of
relatively high moisture content. The ASR results in the formation of
an expansive white colored gel-like material which forms the
destructive tensile stresses inside hardened concrete. In this research, different types of local aggregates available in the
State of Arkansas were mixed and mortar bars were poured according
to the ASTM specifications. Mortar bars expansion was measured
versus time and aggregates with potential ASR problems were
detected. Different types of supplementary cementitious materials
(SCMs) were used in remixing mortar bars with highly reactive
aggregates. Length changes for remixed bars proved that different
types of SCMs can be successfully used in reducing the expansive
effect of ASR. SCMs percentage by weight is highly dependent on
the SCM type. The result of this study will help avoiding future
losses due to ASR cracking in construction project and reduce the
maintenance, repair, and replacement budgets required for highways
network.
Abstract: Digital technologies offer many opportunities in the
design and implementation of brand communication and advertising.
Augmented reality (AR) is an innovative technology in marketing
communication that focuses on the fact that virtual interaction with a
product ad offers additional value to consumers. AR enables
consumers to obtain (almost) real product experiences by the way of
virtual information even before the purchase of a certain product.
Aim of AR applications in relation with advertising is in-depth
examination of product characteristics to enhance product knowledge
as well as brand knowledge. Interactive design of advertising
provides observers with an intense examination of a specific
advertising message and therefore leads to better brand knowledge.
The elaboration likelihood model and the central route to persuasion
strongly support this argumentation. Nevertheless, AR in brand
communication is still in an initial stage and therefore scientific
findings about the impact of AR on information processing and brand
attitude are rare. The aim of this paper is to empirically investigate
the potential of AR applications in combination with traditional print
advertising. To that effect an experimental design with different
levels of interactivity is built to measure the impact of interactivity of
an ad on different variables o advertising effectiveness.
Abstract: Device-to-device (D2D) communication is considered a
promising technique to provide wireless peer-to-peer communication
services. Due to increasing demand on mobile services, available
spectrum for radio frequency (RF) based communications becomes
scarce. Recently, visible light communications (VLC) has evolved
as a high speed wireless data transmission technology for indoor
environments with abundant available bandwidth. In this paper,
a novel VLC based D2D communication that provides wireless
peer-to-peer communication is proposed. Potential low operating
power devices for an efficient D2D communication over increasing
distance of separation between devices is analyzed. Optical repeaters
(OR) are also proposed to enhance the performance in an environment
where direct D2D communications yield degraded performance.
Simulation results show that VLC plays an important role in
providing efficient D2D communication up to a distance of 1 m
between devices. It is also found that the OR significantly improves
the coverage distance up to 3.5 m.
Abstract: The aim of this article is to identify the measures
companies undertake in order to adapt to the environment as well as
discussing their diversity and effectiveness. The research methods
used in the study include an in-depth analysis of the literature and a
case study, which helps to illustrate the issue in question. Referring to
the concept of agility, which is firmly embedded in the theory of
strategic management and has been developed with the aim of
adapting to the environment and its changes, the paper first examines
different types of adaptation measures for companies. Then the issue
under discussion is illustrated with the example of the company
Hortimex. This company is an eminent representative of the world’s
leading manufacturers of food additives and ingredients. The
company was established in 1988 and is a family business, which in
practice means that it conducts business in a responsible manner,
observing the law and respecting the interests of society and the
environment. The company’s mission is to develop a market in
Poland for the products and solutions offered by their partners and to
share their knowledge of additives in food production and
consumption.
Abstract: This research provides a technical account of
estimating Transition Probability using Time-homogeneous Markov
Jump Process applying by South African HIV/AIDS data from the
Statistics South Africa. It employs Maximum Likelihood Estimator
(MLE) model to explore the possible influence of Transition
Probability of mortality cases in which case the data was based on
actual Statistics South Africa. This was conducted via an integrated
demographic and epidemiological model of South African HIV/AIDS
epidemic. The model was fitted to age-specific HIV prevalence data
and recorded death data using MLE model. Though the previous
model results suggest HIV in South Africa has declined and AIDS
mortality rates have declined since 2002 – 2013, in contrast, our
results differ evidently with the generally accepted HIV models
(Spectrum/EPP and ASSA2008) in South Africa. However, there is
the need for supplementary research to be conducted to enhance the
demographic parameters in the model and as well apply it to each of
the nine (9) provinces of South Africa.
Abstract: The tribological test with Pin-On-Disc configuration
measures friction and wear properties in dry or lubricated sliding
surfaces of a variety of materials and coatings. Polymeric matrix
composites loaded with mineral filler were used, 1%, 3%, 10%, 30%,
and 50% mass percentage of filler, to reduce the material cost by
using mineral tailings. Using a pin-on-disc tribometer to quantify
coefficient of friction and wear resistance of the specimens. The
parameters known to performing the test were 300 rpm rotation,
normal load of 16N and duration of 33.5 minutes. The composite
with 10% mineral filler performed better, considering that the wear
resistance was good when compared to the other compositions and an
average low coefficient of friction, in the order of μ ≤ 0.15.
Abstract: Historic paths in today's cities are facing the pressure
of the urban development due to the rapid urban growth. Every new
development is tearing the old urban fabric and the socio-economic
character of the historic paths. Furthermore, in some cases historic
paths suffer from negligence and decay. Kom El Dekka historic path
was one of those deteriorated paths in the city of Alexandria, Egypt,
in spite of its high heritage and socio-economic value. Therefore,
there was a need to develop urban regeneration strategies as a part of
a wider sustainable development vision, to handle the situation and
revitalize the path as a livable space in the heart of the city. This
study aims to develop a comprehensive assessment methodology to
evaluate the different values of the path and to create community-oriented
and economic-based analysis methodology for its socio-economic
values. These analysis and assessments provide strategies
for any regeneration action plan for Kom El Dekka historic path.
Abstract: Effect of Zn addition on the microstructure and
mechanical properties of Mg-Zn alloys with Zn contents from 6 to 10
weight percent was investigated in this study. Through calculation of
phase equilibria of Mg-Zn alloys, carried out by using FactSage® and
FTLite database, solution treatment temperature was decided as
temperatures from 300 to 400oC, where supersaturated solid solution
can be obtained. Solid solution treatment of Mg-Zn alloys was
successfully conducted at 380oC and supersaturated microstructure
with all beta phase resolved into matrix was obtained. After solution
treatment, hot rolling was successfully conducted by reduction of
60%. Compression and tension tests were carried out at room
temperature on the samples as-cast, solution treated, hot-rolled and
recrystallized after rolling. After solid solution treatment, each alloy
was annealed at temperatures of 180 and 200oC for time intervals from
1 min to 48 hrs and hardness of each condition was measured by
micro-Vickers method. Peak aging conditions were deduced as at the
temperature of 200oC for 10 hrs. By addition of Zn by 10 weight
percent, hardness and strength were enhanced.
Abstract: The Flexible AC Transmission System (FACTS)
technology is a new advanced solution that increases the reliability
and provides more flexibility, controllability, and stability of a power
system. The Unified Power Flow Controller (UPFC), as the most
versatile FACTS device for regulating power flow, is able to control
respectively transmission line real power, reactive power, and node
voltage. The main purpose of this paper is to analyze the effect of the
UPFC on the load flow, the power losses, and the voltage stability
using NEPLAN software modules, Newton-Raphson load flow is
used for the power flow analysis and the modal analysis is used for
the study of the voltage stability. The simulation was carried out on
the IEEE 14-bus test system.
Abstract: Autologous Chondrocyte Implantation (ACI) is used worldwide since 1998 to treat cartilage defect. GEL based ACI is a new tissue-engineering technique to treat full thickness cartilage defect with fibrin and thrombin as scaffold for chondrocytes. Purpose of this study is to see safety and efficacy of gel based ACI for knee cartilage defect in multiple centres with different surgeons. Gel-based Autologous Chondrocyte Implantation (GACI) has shown effectiveness in treating isolated cartilage defect of knee joint. Long term results are still needed to be studied. This study was followed-up up to two years and showed benefit to patients. All enrolled patients with a mean age of 28.5 years had an average defect size of3 square centimeters, and were grade IV as per ICRS grading. All patients were followed up several times and at several intervals at 6th week, 8th week, 11th week, 17th week, 29th week, 57th week after surgery. The outcomes were measured based on the IKDC (subjective and objective) and MOCART scores.
Abstract: Community living adjacent to forests and Protected
Areas, especially in South Asian countries, have a common practice
in extracting resources for their living and livelihoods. This
extraction of resources, because the way it is done, destroys the biophysical
features of the area. Deforestation, wildlife poaching, illegal
logging, unauthorized hill cutting etc. are some of the serious issues
of concern for the sustainability of the natural resources that has a
direct impact on environment and climate as a whole. To ensure
community involvement in conservation initiatives of the state,
community based forest management, commonly known as Comanagement,
has been in practice in 6 South Asian countries. These
are -India, Nepal, Sri Lanka, Pakistan, Bhutan and Bangladesh.
Involving community in forestry management was initiated first in
Bangladesh in 1979 and reached as an effective co-management
approach through a several paradigm shifts. This idea of Comanagement
has been institutionalized through a Government Order
(GO) by the Ministry of Environment and Forests, Government of
Bangladesh on November 23, 2009. This GO clearly defines the
structure and functions of Co-management and its different bodies.
Bangladesh Forest Department has been working in association with
community to conserve and manage the Forests and Protected areas
of Bangladesh following this legal document. Demographically
young people constitute the largest segment of population in
Bangladesh. This group, if properly sensitized, can produce valuable
impacts on the conservation initiatives, both by community and
government. This study traced the major factors that motivate
community youths to work effectively with different tiers of comanagement
organizations in conservation of forests and Protected
Areas of Bangladesh. For the purpose of this study, 3 FGDs were
conducted with 30 youths from the community living around the
Protected Areas of Cox’s bazar, South East corner of Bangladesh,
who are actively involved in Co-management organizations. KII were
conducted with 5 key officials of Forest Department stationed at
Cox’s Bazar. 2 FGDs were conducted with the representatives of 7
Co-management organizations working in Cox’s Bazar region and
approaches of different community outreach activities conducted for
forest conservation by 3 private organizations and Projects have been
reviewed. Also secondary literatures were reviewed for the history
and evolution of Co-management in Bangladesh and six South Asian
countries. This study found that innovative community outreach
activities that are financed by public and private sectors involving
youths and community as a whole have played a pivotal role in
conservation of forests and Protected Areas of the region. This
approach can be replicated in other regions of Bangladesh as well as
other countries of South Asia where Co-Management exists in
practice.
Abstract: HMS Industrial Networks AB has been recognized as
one of the most innovative companies in the industrial
communication industry worldwide. The creation of their Anybus
innovation during the 1990s contributed considerably to the
company’s success. From inception, HMS’ employees were
innovating for the purpose of creating new business (the creation
phase). After the Anybus innovation, they began the process of
internationalization (the commercialization phase), which in turn led
them to concentrate on cost reduction, product quality, delivery
precision, operational efficiency, and increasing growth (the growth
phase). As a result of this transformation, performing new radical
innovations have become more complicated. The purpose of our research was to explore the dynamics of
innovation at HMS from the aspect of key actors, activities, and
events, over the three phases, in order to understand what led to the
creation of their Anybus innovation, and why it has become
increasingly challenging for HMS to create new radical innovations
for the future. Our research methodology was based on a longitudinal,
retrospective study from the inception of HMS in 1988 to 2014, a
single case study inspired by the grounded theory approach. We
conducted 47 interviews and collected 1 024 historical documents for
our research. Our analysis has revealed that HMS’ success in creating the
Anybus, and developing a successful business around the innovation,
was based on three main capabilities – cultivating customer relations
on different managerial and organizational levels, inspiring business
relations, and balancing complementary human assets for the purpose
of business creation. The success of HMS has turned the management’s attention away
from past activities of key actors, of their behavior, and how they
influenced and stimulated the creation of radical innovations.
Nowadays, they are rhetorically focusing on creativity and
innovation. All the while, their real actions put emphasis on growth,
cost reduction, product quality, delivery precision, operational
efficiency, and moneymaking. In the process of becoming an
international company, HMS gradually refocused. In so doing they
became profitable and successful, but they also forgot what made
them innovative in the first place. Fortunately, HMS’ management
has come to realize that this is the case and they are now in search of
recapturing innovation once again. Our analysis indicates that HMS’ management is facing several
barriers to innovation related path dependency and other lock-in
phenomena. HMS’ management has been captured, trapped in their
mindset and actions, by the success of the past. But now their future has to be secured, and they have come to realize that moneymaking is
not everything. In recent years, HMS’ management have begun to
search for innovation once more, in order to recapture their past
capabilities for creating radical innovations. In order to unlock their
managerial perceptions of customer needs and their counter-innovation
driven activities and events, to utilize the full potential of
their employees and capture the innovation opportunity for the future.
Abstract: The rapid growth of the human population and the
environmental degradation associated with increased consumption of
resources raises concerns on sustainability. Social sustainability
constitutes one of the three dimensions of sustainability together with
environmental and economic dimensions. Even though there is not an
agreement on what social sustainability consists of, it is a well known
fact that it necessitates user participation. The fore, this study aims to
observe and analyze the role of user participation on social
sustainability. In this paper, the links between user participation and indicators of
social sustainability have been searched. In order to achieve this, first
of all a literature review on social sustainability has been done;
accordingly, the information obtained from researches has been used
in the evaluation of the projects conducted in the developing
countries considering user participation. These examples are taken as
role models with pros and cons for the development of the checklist
for the evaluation of the case studies. Furthermore, a case study over
the post earthquake residential settlements in Turkey have been
conducted. The case study projects are selected considering different building
scales (differing number of residential units), scale of the problem
(post-earthquake settlements, rehabilitation of shanty dwellings) and
the variety of users (differing socio-economic dimensions). Decisionmaking,
design, building and usage processes of the selected projects
and actors of these processes have been investigated in the context of
social sustainability. The cases include: New Gourna Village by
Hassan Fathy, Quinta Monroy dwelling units conducted in Chile by
Alejandro Aravena and Beyköy and Beriköy projects in Turkey
aiming to solve the problem of housing which have appeared after the
earthquake happened in 1999 have been investigated. Results of the
study possible links between social sustainability indicators and user
participation and links between user participation and the
peculiarities of place. Results are compared and discussed in order to find possible
solutions to form social sustainability through user participation.
Results show that social sustainability issues depend on communities'
characteristics, socio-economic conditions and user profile but user
participation has positive effects on some social sustainability
indicators like user satisfaction, a sense of belonging and social
stability.
Abstract: Sentiment analysis (SA) has received growing
attention in Arabic language research. However, few studies have yet
to directly apply SA to Arabic due to lack of a publicly available
dataset for this language. This paper partially bridges this gap due to
its focus on one of the Arabic dialects which is the Saudi dialect. This
paper presents annotated data set of 4700 for Saudi dialect sentiment
analysis with (K= 0.807). Our next work is to extend this corpus and
creation a large-scale lexicon for Saudi dialect from the corpus.
Abstract: The exploitation of flow pulsation in micro- and
mini-channels is a potentially useful technique for enhancing cooling
of high-end photonics and electronics systems. It is thought that
pulsation alters the thickness of the hydrodynamic and thermal
boundary layers, and hence affects the overall thermal resistance
of the heat sink. Although the fluid mechanics and heat transfer
are inextricably linked, it can be useful to decouple the parameters
to better understand the mechanisms underlying any heat transfer
enhancement. Using two-dimensional, two-component particle image
velocimetry, the current work intends to characterize the heat transfer
mechanisms in pulsating flow with a mean Reynolds number of
48 by experimentally quantifying the hydrodynamics of a generic
liquid-cooled channel geometry. Flows circulated through the test
section by a gear pump are modulated using a controller to achieve
sinusoidal flow pulsations with Womersley numbers of 7.45 and
2.36 and an amplitude ratio of 0.75. It is found that the transient
characteristics of the measured velocity profiles are dependent on the
speed of oscillation, in accordance with the analytical solution for
flow in a rectangular channel. A large velocity overshoot is observed
close to the wall at high frequencies, resulting from the interaction
of near-wall viscous stresses and inertial effects of the main fluid
body. The steep velocity gradients at the wall are indicative of
augmented heat transfer, although the local flow reversal may reduce
the upstream temperature difference in heat transfer applications.
While unsteady effects remain evident at the lower frequency, the
annular effect subsides and retreats from the wall. The shear rate at
the wall is increased during the accelerating half-cycle and decreased
during deceleration compared to steady flow, suggesting that the flow
may experience both enhanced and diminished heat transfer during
a single period. Hence, the thickness of the hydrodynamic boundary
layer is reduced for positively moving flow during one half of the
pulsation cycle at the investigated frequencies. It is expected that the
size of the thermal boundary layer is similarly reduced during the
cycle, leading to intervals of heat transfer enhancement.
Abstract: In general, it is desirable to finish the weld quickly,
before a large volume of surrounding metal heats up and expands.
The welding process used, type, welding current and speed of travel,
thus, affect the degree of shrinkage and distortion of a weldment. The
use of mechanized welding equipment reduces welding time, metal
affected zone and consequently distortion. This article helps to define
what weld distortion is and then provide a practical understanding of
the causes of distortion, effects of shrinkage in butt joint welded
assemblies using TI6AL4VA and Aluminium AA2024 alloy sheet.
The beam offset position to the joint interface towards titanium and
aluminium side. The factors affecting distortion during welding is
also given. Test results reveal that welding speed is the significant
parameter to decide the extent of distortion. Also welding from Al
side reduces the distortion while Ti side increases the distortion.
Abstract: Sisal leaves were subjected to enzymatic retting
method to extract the sisal fibre. A portion of the fibre was pretreated
with alkali (NaOH), and further treated with benzoyl chloride
and silane treatment reagents. Both the treated and untreated Sisal
fibre composites were used to fabricate the composite by hand lay-up
technique using unsaturated polyester resin. Tensile, flexural, water
absorption, density, thickness swelling and chemical resistant tests
were conducted and evaluated on the composites. Results obtained
for all the parameters showed an increase in the treated fibre
compared to untreated fibre. FT-IR spectra results ascertained the
inclusion of benzoyl and silane groups on the fibre surface. Scanning
electron microscopy (SEM) result obtained showed variation in the
morphology of the treated and untreated fibre. Chemical modification
was found to improve adhesion of the fibre to the matrix, as well as
physico-mechanical properties of the composites.