Abstract: In this study, in order to clarify wind-induced
phenomena, especially vertical mixing of density stratification in a
closed water area with floating-leaved plants, we conducted hydraulic
experiments on wind flow characteristics, wind wave characteristics,
entrainment phenomena and turbulent structure by using a wind tunnel
test tank and simulated floating-leaved plants. From the experimental
results of wind flow and wind wave characteristics, we quantified the
impact of the occupancy rate of the plants on their resistance
characteristics. From the experimental results of entrainment
phenomena, we defined the parameter that could explain the
magnitude of mixing between the density stratifications, and
quantified the impact of the occupancy rate on vertical mixing
between stratifications. From the experimental results of the turbulent
structure of the upper layer, we clarified the differences in small-scale
turbulence components at each occupancy rate and quantified the
impact of the occupancy rate on the turbulence characteristics. For a
summary of this study, we theoretically quantified wind-induced
entrainment phenomena in a closed water area with luxuriant growth
of floating-leaved plants. The results indicated that the impact of
luxuriant growth of floating-leaved plants in a closed water body
could be seen in the difference in small-scale fluid characteristics, and
these characteristics could be expressed using the small-scale
turbulent components.
Abstract: A high performance clarification system has been
discussed for advanced aqueous reprocessing of FBR spent fuel.
Dissolver residue gives the cause of troubles on the plant operation of
reprocessing. In this study, the new clarification system based on the
hybrid of centrifuge and filtration was proposed to get the high
separation ability of the component of whole insoluble sludge. The
clarification tests of simulated solid species were carried out to
evaluate the clarification performance using small-scale test apparatus
of centrifuge and filter unit. The density effect of solid species on the
collection efficiency was mainly evaluated in the centrifugal
clarification test. In the filtration test using ceramic filter with pore
size of 0.2μm, on the other hand, permeability and filtration rate
were evaluated in addition to the filtration efficiency. As results, it was
evaluated that the collection efficiency of solid species on the new
clarification system was estimated as nearly 100%. In conclusion, the
high clarification performance of dissolver liquor can be achieved by
the hybrid of the centrifuge and filtration system.
Abstract: Reasonably priced and well-constructed housing must
be an integral and element supporting a healthy society. The absence
of housing everyone in society can afford negatively affects the
people's health, education, ability to get jobs, develop their
community. Without access to decent housing, economic
development, integration of immigrants and inclusiveness, the society
is negatively impacted. Canada has a sterling record in creating
housing compared to many other nations around the globe. Canadian
housing gets support from a mature and responsive mortgage network
and a top-quality construction industry as well as safe and excellent
quality building materials that are readily available. Yet 1.7 million
Canadian households occupy substandard abodes. During the past
hundred years, Canada's government has made a wide variety of
attempts to provide decent residential facilities every Canadian can
afford. Despite these laudable efforts, today Canada is left with
housing that is inadequate for many Canadians. People who own their
housing are given all kinds of privileges and perks, while people with
relatively low incomes who rent their apartments or houses are
discriminated against.
To help solve these problems, zoning that is based on an
"inclusionary" philosophy is tool developed to help provide people
the affordable residences that they need. No, thirty years after its
introduction, this type of zoning has been shown effective in helping
build and provide Canadians with a houses or apartments they can
afford to pay for. Using this form of zoning can have different results
+depending on where and how it is used. After examining Canadian
affordable housing and four American cases where this type of
zoning was enforced in the USA, this makes various
recommendations for expanding Canadians' access to housing they
can afford.
Abstract: This paper presents an evaluation of the wind potential in the area of the Lagoon of Venice (Italy). A full anemometric campaign of 2 year measurements, performed by the "Osservatorio Bioclimatologico dell'Ospedale al Mare di Venezia" has been analyzed to obtain the Weibull wind speed distribution and the main wind directions. The annual energy outputs of two candidate horizontal-axis wind turbines (“Aventa AV-7 LoWind" and “Gaia Wind 133-11kW") have been estimated on the basis of the computed Weibull wind distribution, registering a better performance of the former turbine, due to a higher ratio between rotor swept area and rated power of the electric generator, determining a lower cut-in wind speed.
Abstract: The present study has been taken to explore the
screening of in vitro antimicrobial activities of D-galactose-binding
sponge lectin (HOL-30). HOL-30 was purified from the marine
demosponge Halichondria okadai by affinity chromatography. The
molecular mass of the lectin was determined to be 30 kDa with a
single polypeptide by SDS-PAGE under non-reducing and reducing
conditions. HOL-30 agglutinated trypsinized and glutaraldehydefixed
rabbit and human erythrocytes with preference for type O
erythrocytes. The lectin was subjected to evaluation for inhibition of
microbial growth by the disc diffusion method against eleven human
pathogenic gram-positive and gram-negative bacteria. The lectin
exhibited strong antibacterial activity against gram-positive bacteria,
such as Bacillus megaterium and Bacillus subtilis. However, it did
not affect against gram-negative bacteria such as Salmonella typhi
and Escherichia coli. The largest zone of inhibition was recorded of
Bacillus megaterium (12 in diameter) and Bacillus subtilis (10 mm in
diameter) at a concentration of the lectin (250 μg/disc). On the other
hand, the antifungal activity of the lectin was investigated against six
phytopathogenic fungi based on food poisoning technique. The lectin
has shown maximum inhibition (22.83%) of mycelial growth of
Botrydiplodia theobromae at a concentration of 100 μg/mL media.
These findings indicate that the lectin may be of importance to
clinical microbiology and have therapeutic applications.
Abstract: REY area has been located in Tehran Province and several archaeological ruins of this area indicate that the settlement in this area has been started since several thousand years ago. In this paper, the main investigation items consist of analysis of oil components and groundwater quality inside the wells. By finding the contents of oil in the well, it is possible to find out the pollution source by comparing the oil contents of well with other oil products that are used inside and outside of the oil farm. Investigation items consist of analysis of BTEX (Benzene, Toluene, Ethyl-benzene, Xylene), Gas chromatographic distillation characteristics, Water content, Density, Sulfur content, Lead content, Atmospheric distillation, MTBE(Methyl tertiary butyl ether). Analysis of polluting oil components showed that except MW(Monitoring Well)10 and MW 15 that oil with slightly heavy components was detected in them; with a high possibility the polluting oil is light oil.
Abstract: One of the vital developmental tasks that an
individual faces during adolescence is choosing a career. Arriving at
a career decision is difficult and anxious for many adolescents in the
tertiary level. The main purpose of this study is to determine the
factors relating to career indecision among freshmen college students
as basis for the formulation of a comprehensive career counseling
program for the psychological well-being of freshmen university
students. The subjects were purposively selected. The Slovin-s
formula was used in determining the sample size, using a 0.05
margin of error in getting the total number of samples per college and
per major. The researcher made use of descriptive correlational study
in determining significant factors relating to career indecision.
Multiple Regression Analysis indicated that career thoughts, career
decisions and vocational identity as factors related to career
indecision.
Abstract: Natural gas is the most popular fossil fuel in the
current era and future as well. Natural gas is existed in underground
reservoirs so it may contain many of non-hydrocarbon components
for instance, hydrogen sulfide, nitrogen and water vapor. These
impurities are undesirable compounds and cause several technical
problems for example, corrosion and environment pollution.
Therefore, these impurities should be reduce or removed from natural
gas stream. Khurmala dome is located in southwest Erbil-Kurdistan
region. The Kurdistan region government has paid great attention for
this dome to provide the fuel for Kurdistan region. However, the
Khurmala associated natural gas is currently flaring at the field.
Moreover, nowadays there is a plan to recover and trade this gas and
to use it either as feedstock to power station or to sell it in global
market. However, the laboratory analysis has showed that the
Khurmala sour gas has huge quantities of H2S about (5.3%) and CO2
about (4.4%). Indeed, Khurmala gas sweetening process has been
removed in previous study by using Aspen HYSYS. However,
Khurmala sweet gas still contents some quintets of water about 23
ppm in sweet gas stream. This amount of water should be removed or
reduced. Indeed, water content in natural gas cause several technical
problems such as hydrates and corrosion. Therefore, this study aims
to simulate the prospective Khurmala gas dehydration process by
using Aspen HYSYS V. 7.3 program. Moreover, the simulation
process succeeded in reducing the water content to less than 0.1ppm.
In addition, the simulation work is also achieved process
optimization by using several desiccant types for example, TEG and
DEG and it also study the relationship between absorbents type and
its circulation rate with HCs losses from glycol regenerator tower.
Abstract: A design of communication area for infrared
electronic-toll-collection systems to provide an extended
communication interval in the vehicle traveling direction and
regular boundary between contiguous traffic lanes is proposed.
By utilizing two typical low-cost commercial infrared LEDs with
different half-intensity angles Φ1/2 = 22◦ and 10◦, the radiation
pattern of the emitter is designed to properly adjust the spatial
distribution of the signal power. The aforementioned purpose
can be achieved with an LED array in a three-piece structure
with appropriate mounting angles. With this emitter, the influence
of the mounting parameters, including the mounting height and
mounting angles of the on-board unit and road-side unit, on the
system performance in terms of the received signal strength and
communication area are investigated. The results reveal that, for
our emitter proposed in this paper, the ideal ”long-and-narrow”
characteristic of the communication area is very little affected by
these mounting parameters. An optimum mounting configuration is
also suggested.
Abstract: A two-dimensional numerical simulation of the contribution
of both inertial and aerodynamic forces on the blade loads of
a Vertical-Axis Wind Turbine (VAWT) is presented. After describing
the computational model and the relative validation procedure, a
complete campaign of simulations - based on full RANS unsteady
calculations - is proposed for a three-bladed rotor architecture characterized
by a NACA 0021 airfoil. For each analyzed angular velocity,
the combined effect of pressure and viscous forces acting on every
rotor blade are compared to the corresponding centrifugal forces,
due to the revolution of the turbine, thus achieving a preliminary
estimation of the correlation between overall rotor efficiency and
structural blade loads.
Abstract: This article describes the aspects of the formation of
the national idea and national identity through the prism of gender
control and its contradistinction to the obsolete, Soviet component.
The role of females in ethnic and national projects is considered from
the point of view of Dr. Nira Yuval-Davis: as biological reproducers
of the ethnic communities- members; as reproducers of the boarders
of ethnic/national groups; as central participants in the ideological
reproduction of community and transducers of its culture; as symbols
in ideology, reproduction and transformation of ethnic/national
categories; and as participants of national, economical, political and
military combats. The society of the transitional type uses the
symbolic resources of the formation of gender component in the
national project. The gender patterns act like cultural codes,
executing the important ideological function in formation of the
national female- image, i.e. the discussion on hijab - it-s not just the
discussion on control over the female body, it-s the discussion on the
metaphor of social order.
Abstract: This paper examines and compares several of the most common real time methods. These methods are CORE, YSM, MASCOT, JSD, DARTS, RTSAD, ADARTS, CODARTS, HOOD, HRT-HOOD, ROOM, UML, UML-RT. The methods are compared using attributes like i) usability, ii) compositionality and iii) proper RT notations available. Finally some comparison results are given and discussed.
Abstract: In this paper, genetic algorithm (GA) is proposed for
the design of an optimization algorithm to achieve the bandwidth
allocation of ATM network. In Broadband ISDN, the ATM is a highbandwidth;
fast packet switching and multiplexing technique. Using
ATM it can be flexibly reconfigure the network and reassign the
bandwidth to meet the requirements of all types of services. By
dynamically routing the traffic and adjusting the bandwidth
assignment, the average packet delay of the whole network can be
reduced to a minimum. M/M/1 model can be used to analyze the
performance.
Abstract: Attachment of the circulating monocytes to the
endothelium is the earliest detectable events during formation of
atherosclerosis. The adhesion molecules, chemokines and matrix
proteases genes were identified to be expressed in atherogenesis.
Expressions of these genes may influence structural integrity of the
luminal endothelium. The aim of this study is to relate changes in the
ultrastructural morphology of the aortic luminal surface and gene
expressions of the endothelial surface, chemokine and MMP-12 in
normal and hypercholesterolemic rabbits. Luminal endothelial
surface from rabbit aortic tissue was examined by scanning electron
microscopy (SEM) using low vacuum mode to ascertain
ultrastructural changes in development of atherosclerotic lesion. Gene
expression of adhesion molecules, MCP-1 and MMP-12 were studied
by Real-time PCR. Ultrastructural observations of the aortic luminal
surface exhibited changes from normal regular smooth intact
endothelium to irregular luminal surface including marked globular
appearance and ruptures of the membrane layer. Real-time PCR
demonstrated differentially expressed of studied genes in
atherosclerotic tissues. The appearance of ultrastructural changes in
aortic tissue of hypercholesterolemic rabbits is suggested to have
relation with underlying changes of endothelial surface molecules,
chemokine and MMP-12 gene expressions.
Abstract: In-vitro mouse co-culture of E14 embryonic stem cells
(ESCs) and OP9 stromal cells can recapitulate the earliest stages of
haematopoietic development, not accessible in human embryos,
supporting both haemogenic precursors and their primitive
haematopoietic progeny. 1α, 25-Dihydroxy-vitamin D3 (VD3) has
been demonstrated to be a powerful differentiation inducer for a wide
variety of neoplastic cells, and could enhance early differentiation of
ESCs into blood cells in E14/OP9 co-culture. This study aims to
ascertain whether VD3 is key in promoting differentiation and
suppressing proliferation, by separately investigating the effects of
VD3 on the proliferation phase of the E14 cell line and on stromal
OP9 cells.The results showed that VD3 inhibited the proliferation of
the cells in a dose-dependent manner, quantitatively by decreased cell
number, and qualitatively by alkaline-phosphatase staining that
revealed significant differences between VD3-treated and untreated
cells, characterised by decreased enzyme expression (colourless
cells). Propidium-iodide cell-cycle analyses showed no significant
percentage change in VD3-treated E14 and OP9 cells within their G
and S-phases, compared to the untreated controls, despite the
increased percentage of G-phase compared to the S-phase in a dosedependent
manner. These results with E14 and OP9 cells indicate that
adequate VD3 concentration enhances cellular differentiation and
inhibits proliferation. The results also suggest that if E14 and OP9
cells were co-cultured andVD3-treated, there would be furtherenhanced
differentiation of ESCs into blood cells.
Abstract: This paper describes new computer vision algorithms
that have been developed to track moving objects as part of a
long-term study into the design of (semi-)autonomous vehicles. We
present the results of a study to exploit variable kernels for tracking in
video sequences. The basis of our work is the mean shift
object-tracking algorithm; for a moving target, it is usual to define a
rectangular target window in an initial frame, and then process the data
within that window to separate the tracked object from the background
by the mean shift segmentation algorithm. Rather than use the
standard, Epanechnikov kernel, we have used a kernel weighted by the
Chamfer distance transform to improve the accuracy of target
representation and localization, minimising the distance between the
two distributions in RGB color space using the Bhattacharyya
coefficient. Experimental results show the improved tracking
capability and versatility of the algorithm in comparison with results
using the standard kernel. These algorithms are incorporated as part of
a robot test-bed architecture which has been used to demonstrate their
effectiveness.
Abstract: Model-based approaches have been applied successfully
to a wide range of tasks such as specification, simulation, testing, and
diagnosis. But one bottleneck often prevents the introduction of these
ideas: Manual modeling is a non-trivial, time-consuming task.
Automatically deriving models by observing and analyzing running
systems is one possible way to amend this bottleneck. To
derive a model automatically, some a-priori knowledge about the
model structure–i.e. about the system–must exist. Such a model
formalism would be used as follows: (i) By observing the network
traffic, a model of the long-term system behavior could be generated
automatically, (ii) Test vectors can be generated from the model,
(iii) While the system is running, the model could be used to diagnose
non-normal system behavior.
The main contribution of this paper is the introduction of a model
formalism called 'probabilistic regression automaton' suitable for the
tasks mentioned above.
Abstract: In this paper, all-optical signal processors that perform
both microwave mixing and bandpass filtering in a radio-over-fiber
(RoF) link are presented. The key device is a Mach-Zehnder
modulator (MZM) which performs all-optical microwave mixing. An
up-converted microwave signal is obtained and other unwanted
frequency components are suppressed at the end of the fiber span.
Abstract: Based on Traub-s methods for solving nonlinear
equation f(x) = 0, we develop two families of third-order
methods for solving system of nonlinear equations F(x) = 0. The
families include well-known existing methods as special cases.
The stability is corroborated by numerical results. Comparison
with well-known methods shows that the present methods are
robust. These higher order methods may be very useful in the
numerical applications requiring high precision in their computations
because these methods yield a clear reduction in number of iterations.
Abstract: The main goal of this paper is to establish a
methodology for testing and optimizing GPRS performance over
Libya GSM network as well as to propose a suitable optimization
technique to improve performance. Some measurements of
download, upload, throughput, round-trip time, reliability, handover,
security enhancement and packet loss over a GPRS access network
were carried out. Measured values are compared to the theoretical
values that could be calculated beforehand. This data should be
processed and delivered by the server across the wireless network to
the client. The client on the fly takes those pieces of the data and
process immediately. Also, we illustrate the results by describing the
main parameters that affect the quality of service. Finally, Libya-s
two mobile operators, Libyana Mobile Phone and Al-Madar al-
Jadeed Company are selected as a case study to validate our
methodology.