Abstract: This paper proposes a novel frequency offset (FO) estimator for orthogonal frequency division multiplexing. Simplicity is most significant feature of this algorithm and can be repeated to achieve acceptable accuracy. Also fractional and integer part of FO is estimated jointly with use of the same algorithm. To do so, instead of using conventional algorithms that usually use correlation function, we use DFT of received signal. Therefore, complexity will be reduced and we can do synchronization procedure by the same hardware that is used to demodulate OFDM symbol. Finally, computer simulation shows that the accuracy of this method is better than other conventional methods.
Abstract: This paper proposes a low power SRAM based on
five transistor SRAM cell. Proposed SRAM uses novel word-line
decoding such that, during read/write operation, only selected cell
connected to bit-line whereas, in conventional SRAM (CV-SRAM),
all cells in selected row connected to their bit-lines, which in turn
develops differential voltages across all bit-lines, and this makes
energy consumption on unselected bit-lines. In proposed SRAM
memory array divided into two halves and this causes data-line
capacitance to reduce. Also proposed SRAM uses one bit-line and
thus has lower bit-line leakage compared to CV-SRAM.
Furthermore, the proposed SRAM incurs no area overhead, and has
comparable read/write performance versus the CV-SRAM.
Simulation results in standard 0.25μm CMOS technology shows in
worst case proposed SRAM has 80% smaller dynamic energy
consumption in each cycle compared to CV-SRAM. Besides, energy
consumption in each cycle of proposed SRAM and CV-SRAM
investigated analytically, the results of which are in good agreement
with the simulation results.
Abstract: To reduce the carbon dioxide emission into the
atmosphere, adsorption is believed to be one of the most attractive
methods for post-combustion treatment of flue gas. In this work,
activated carbon (AC) was modified by polyethylenimine (PEI) via
impregnation in order to enhance CO2 adsorption capacity. The
adsorbents were produced at 0.04, 0.16, 0.22, 0.25, and 0.28 wt%
PEI/AC. The adsorption was carried out at a temperature range from
30 °C to 75 °C and five different gas pressures up to 1 atm. TG-DTA,
FT-IR, UV-visible spectrometer, and BET were used to characterize
the adsorbents. Effects of PEI loading on the AC for the CO2
adsorption were investigated. Effectiveness of the adsorbents on the
CO2 adsorption including CO2 adsorption capacity and adsorption
temperature was also investigated. Adsorption capacities of CO2 were
enhanced with the increase in the amount of PEI from 0.04 to 0.22
wt% PEI before the capacities decreased onwards from0.25 wt% PEI
at 30 °C. The 0.22 wt% PEI/AC showed higher adsorption capacity
than the AC for adsorption at 50 °C to 75 °C.
Abstract: This paper presents a wrap-around view system with 4
smart cameras module and remote motion mobile robot control equipped with smart camera module system. The two-level scheme for
remote motion control with smart-pad(IPAD) is introduced on this
paper. In the low-level, the wrap-around view system is controlled or operated to keep the reference points lying around top view image
plane. On the higher level, a robot image based motion controller is utilized to drive the mobile platform to reach the desired position or
track the desired motion planning through image feature feedback. The
design wrap-around view system equipped on presents such advantages as follows: 1) a satisfactory solution for the FOV and affine
problem; 2) free of any complex and constraint with robot pose. The performance of the wrap-around view equipped on mobile robot
remote control is proven by experimental results.
Abstract: Due to the environmental and price issues of current
energy crisis, scientists and technologists around the globe are
intensively searching for new environmentally less-impact form of
clean energy that will reduce the high dependency on fossil fuel.
Particularly hydrogen can be produced from biomass via thermochemical
processes including pyrolysis and gasification due to the
economic advantage and can be further enhanced through in-situ
carbon dioxide removal using calcium oxide. This work focuses on
the synthesis and development of the flowsheet for the enhanced
biomass gasification process in PETRONAS-s iCON process
simulation software. This hydrogen prediction model is conducted at
operating temperature between 600 to 1000oC at atmospheric
pressure. Effects of temperature, steam-to-biomass ratio and
adsorbent-to-biomass ratio were studied and 0.85 mol fraction of
hydrogen is predicted in the product gas. Comparisons of the results
are also made with experimental data from literature. The
preliminary economic potential of developed system is RM 12.57 x
106 which equivalent to USD 3.77 x 106 annually shows economic
viability of this process.
Abstract: This paper illustrates the use of a combined neural
network model for classification of electrocardiogram (ECG) beats.
We present a trainable neural network ensemble approach to develop
customized electrocardiogram beat classifier in an effort to further
improve the performance of ECG processing and to offer
individualized health care.
We process a three stage technique for detection of premature
ventricular contraction (PVC) from normal beats and other heart
diseases. This method includes a denoising, a feature extraction and a
classification. At first we investigate the application of stationary
wavelet transform (SWT) for noise reduction of the
electrocardiogram (ECG) signals. Then feature extraction module
extracts 10 ECG morphological features and one timing interval
feature. Then a number of multilayer perceptrons (MLPs) neural
networks with different topologies are designed.
The performance of the different combination methods as well as
the efficiency of the whole system is presented. Among them,
Stacked Generalization as a proposed trainable combined neural
network model possesses the highest recognition rate of around 95%.
Therefore, this network proves to be a suitable candidate in ECG
signal diagnosis systems. ECG samples attributing to the different
ECG beat types were extracted from the MIT-BIH arrhythmia
database for the study.
Abstract: In this study, the designed dual stage membrane
bioreactor (MBR) system was conceptualized for the treatment of
cyanide and heavy metals in electroplating wastewater. The design
consisted of a primary treatment stage to reduce the impact of
fluctuations and the secondary treatment stage to remove the residual
cyanide and heavy metal contaminants in the wastewater under
alkaline pH conditions. The primary treatment stage contained
hydrolyzed Citrus sinensis (C. sinensis) pomace and the secondary
treatment stage contained active Aspergillus awamori (A. awamori)
biomass, supplemented solely with C. sinensis pomace extract from
the hydrolysis process. An average of 76.37%, 95.37%, 93.26 and
94.76% and 99.55%, 99.91%, 99.92% and 99.92% degradation
efficiency for total cyanide (T-CN), including the sorption of nickel
(Ni), zinc (Zn) and copper (Cu) were observed after the first and
second treatment stages, respectively. Furthermore, cyanide
conversion by-products degradation was 99.81% and 99.75 for both
formate (CHOO-) and ammonium (NH4
+) after the second treatment
stage. After the first, second and third regeneration cycles of the C.
sinensis pomace in the first treatment stage, Ni, Zn and Cu removal
achieved was 99.13%, 99.12% and 99.04% (first regeneration cycle),
98.94%, 98.92% and 98.41% (second regeneration cycle) and 98.46
%, 98.44% and 97.91% (third regeneration cycle), respectively.
There was relatively insignificant standard deviation detected in all
the measured parameters in the system which indicated
reproducibility of the remediation efficiency in this continuous
system.
Abstract: Fixed-bed slow pyrolysis experiments of rice husk
have been conducted to determine the effect of pyrolysis
temperature, heating rate, particle size and reactor length on the
pyrolysis product yields. Pyrolysis experiments were performed at
pyrolysis temperature between 400 and 600°C with a constant
heating rate of 60°C/min and particle sizes of 0.60-1.18 mm. The
optimum process conditions for maximum liquid yield from the rice
husk pyrolysis in a fixed bed reactor were also identified. The highest
liquid yield was obtained at a pyrolysis temperature of 500°C,
particle size of
1.18-1.80 mm, with a heating rate of 60°C/min in a 300 mm length
reactor. The obtained yield of, liquid, gas and solid were found be in
the range of 22.57-31.78 %, 27.75-42.26 % and 34.17-42.52 % (all
weight basics) respectively at different pyrolysis conditions. The
results indicate that the effects of pyrolysis temperature and particle
size on the pyrolysis yield are more significant than that of heating
rate and reactor length. The functional groups and chemical
compositions present in the liquid obtained at optimum conditions
were identified by Fourier Transform-Infrared (FT-IR) spectroscopy
and Gas Chromatography/ Mass Spectroscopy (GC/MS) analysis
respectively.
Abstract: Unlike its conventional counterpart, Islamic principles
forbid Islamic banks to take any interest-related income and thus
makes deposits from depositors as an important source of fund for its
operational and financing. Consequently, the risk of deposit
withdrawal by depositors is an important aspect that should be wellmanaged
in Islamic banking. This paper aims to investigate factors
that influence depositors- withdrawal behavior in Islamic banks,
particularly in Malaysia, using the framework of theory of reasoned
action. A total of 368 respondents from Klang valley are involved in
the analysis. The paper finds that all the constructs variable i.e.
normative beliefs, subjective norms, behavioral beliefs, and attitude
towards behavior are perceived to be distinct by the respondents. In
addition, the structural equation model is able to verify the structural
relationships between subjective norms, attitude towards behavior
and behavioral intention. Subjective norms gives more influence to
depositors- decision on deposit withdrawal compared to attitude
towards behavior.
Abstract: We developed a non-contact method for the in-situ
monitoring of the thermal forming of glass and Si foils to optimize
the manufacture of mirrors for high-resolution space x-ray
telescopes. Their construction requires precise and light-weight
segmented optics with angular resolution better than 5 arcsec. We
used 75x25 mm Desag D263 glass foils 0.75 mm thick and 0.6 mm
thick Si foils. The glass foils were shaped by free slumping on a
frame at viscosities in the range of 109.3-1012 dPa·s, the Si foils by
forced slumping above 1000°C. Using a Nikon D80 digital camera,
we took snapshots of a foil-s shape every 5 min during its isothermal
heat treatment. The obtained results we can use for computer
simulations. By comparing the measured and simulated data, we can
more precisely define material properties of the foils and optimize
the forming technology.
Abstract: How to effectively allocate system resource to process
the Client request by Gateway servers is a challenging problem. In
this paper, we propose an improved scheme for autonomous
performance of Gateway servers under highly dynamic traffic loads.
We devise a methodology to calculate Queue Length and Waiting
Time utilizing Gateway Server information to reduce response time
variance in presence of bursty traffic. The most widespread
contemplation is performance, because Gateway Servers must offer
cost-effective and high-availability services in the elongated period,
thus they have to be scaled to meet the expected load. Performance
measurements can be the base for performance modeling and
prediction. With the help of performance models, the performance
metrics (like buffer estimation, waiting time) can be determined at
the development process. This paper describes the possible queue
models those can be applied in the estimation of queue length to
estimate the final value of the memory size. Both simulation and
experimental studies using synthesized workloads and analysis of
real-world Gateway Servers demonstrate the effectiveness of the
proposed system.
Abstract: An attempt has been made to determine the strength
and impact properties of Cr-Mo steel weld and base materials by
varying the current during manual metal arc welding. Toughness over
a temperature range from -32 to 100°C of base, heat affected zone
(HAZ) and weld zones at three current settings are made. It is
observed that the deterioration in notch toughness at any zone with
the temperature decreases. The values of notch toughness for all
zones at -32°C are almost same for any current settings. The values
of notch toughness at HAZ area are higher than that of weld area due
to the coarsening of ferrite grain of HAZ occurs with higher heat
input. From microhardness and microstructure result, it can be
concluded that large inclusion content in weld deposit is the cause of
lower notch toughness value.
Abstract: Design and land use are closely linked to the
energy efficiency levels for an urban area. The current city
planning practice does not involve an effective land useenergy
evaluation in its 'blueprint' urban plans. The study
proposed an appraisal method that can be embedded in GIS
programs using five planning criteria as how far a planner can
give away from the planning principles (criteria) for the most
energy output s/he can obtain. The case of Balcova, a district
in the Izmir Metropolitan area, is used conformingly for
evaluating the proposed master plan and the geothermal
energy (heating only) use for the concern district.
If the land use design were proposed accordingly at-most
energy efficiency (a 30% obtained), mainly increasing the
density around the geothermal wells and also proposing more
mixed use zones, we could have 17% distortion (infidelity to
the main planning principles) from the original plan. The
proposed method can be an effective tool for planners as
simulation media, of which calculations can be made by GIS
ready tools, to evaluate efficiency levels for different plan
proposals, letting to know how much energy saving causes
how much deviation from the other planning ideals. Lower
energy uses can be possible for different land use proposals
for various policy trials.
Abstract: Environmental aspects plays a central role in environmental management system (EMS) because it is the basis for the identification of an organization-s environmental targets. The
existing methods for the assessment of environmental aspects are grouped into three categories: risk assessment-based (RA-based),
LCA-based and criterion-based methods. To combine the benefits of
these three categories of research, this study proposes an integrated framework, combining RA-, LCA- and criterion-based methods. The
integrated framework incorporates LCA techniques for the identification of the causal linkage for aspect, pathway, receptor and
impact, uses fuzzy logic to assess aspects, considers fuzzy conditions,
in likelihood assessment, and employs a new multi-criteria decision analysis method - multi-criteria and multi-connection comprehensive
assessment (MMCA) - to estimate significant aspects in EMS. The proposed model is verified, using a real case study and the results show
that this method successfully prioritizes the environmental aspects.
Abstract: Deoxygenation of beef fat for the production of hydrogenated biodiesel is investigated in a high pressure continuous flow fixed bed reactor over palladium-supported mesoporous titania catalyst synthesized via a combined single-step sol-gel process with surfactant-assisted templating method (SATM). The catalyst possessed a mesoporous charactheristic with high surface area and narrow pore size distribution. The main products of all Pd/TiO2 catalysts are n-heptadecane (n-C17) and n-pentadecane (n-C15) resulting from decarbonylation reaction. Pd/TiO2 catalyst synthesized via a combined single-step sol-gel process with SATM (SSSG) gave higher activity and selectivity to the desired products when compared to IWI/SG-TiO2 and IWI/P25-TiO2, respectively. SSSG catalyst gave the average conversion up to 80-90 % and 80 % for the selectivity in diesel range hydrocarbons. This result may cause by the higher surface area and the ability in dispersion of palladium ion in mesoporous of TiO2 during sol-gel process.
Abstract: Testing accounts for the major percentage of technical
contribution in the software development process. Typically, it
consumes more than 50 percent of the total cost of developing a
piece of software. The selection of software tests is a very important
activity within this process to ensure the software reliability
requirements are met. Generally tests are run to achieve maximum
coverage of the software code and very little attention is given to the
achieved reliability of the software. Using an existing methodology,
this paper describes how to use Bayesian Belief Networks (BBNs) to
select unit tests based on their contribution to the reliability of the
module under consideration. In particular the work examines how the
approach can enhance test-first development by assessing the quality
of test suites resulting from this development methodology and
providing insight into additional tests that can significantly reduce
the achieved reliability. In this way the method can produce an
optimal selection of inputs and the order in which the tests are
executed to maximize the software reliability. To illustrate this
approach, a belief network is constructed for a modern software
system incorporating the expert opinion, expressed through
probabilities of the relative quality of the elements of the software,
and the potential effectiveness of the software tests. The steps
involved in constructing the Bayesian Network are explained as is a
method to allow for the test suite resulting from test-driven
development.
Abstract: Information and Communication Technologies (ICT) are increasing in importance everyday, especially since the 90’s (last decade of birth for the Millennials generation). While social interactions involving the Millennials generation have been studied, a lack of investigation remains regarding the use of the ICT by this generation as well as the impact on outcomes in education and professional training. Observing and interviewing students preparing a MSc, we aimed at characterizing the interaction students-ICT during the courses. We found that up to 50% of the students (mainly female) could use ICT during courses at a rate of 0.84 occurrence/minutes for some of them, and they thought this involvement did not disturb learning, even was helpful. As recent researches show that multitasking leads people think they are much better than they actually are, further observations with assessments are needed to conclude whether or not the use ICT by students during the courses is a real strength.
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: The state-of-the-art Bag of Words model in Content-
Based Image Retrieval has been used for years but the relevance
feedback strategies for this model are not fully investigated. Inspired
from text retrieval, the Bag of Words model has the ability to use the
wealth of knowledge and practices available in text retrieval. We
study and experiment the relevance feedback model in text retrieval
for adapting it to image retrieval. The experiments show that the
techniques from text retrieval give good results for image retrieval
and that further improvements is possible.
Abstract: The selection of parents and breeding strategies for
the successful maize hybrid production will be facilitated by
heterotic groupings of parental lines and determination of combining
abilities of them. Fourteen maize inbred lines, used in maize breeding
programs in Iran, were crossed in a diallel mating design. The 91 F1
hybrids and the 14 parental lines were studied during two years at
four locations of Iran for investigation of combining ability of
gentypes for grain yield and to determine heterotic patterns among
germplasm sources, using both, the Griffing-s method and the biplot
approach for diallel analysis. The graphical representation offered by
biplot analysis allowed a rapid and effective overview of general
combining ability (GCA) and specific combining ability (SCA)
effects of the inbred lines, their performance in crosses, as well as
grouping patterns of similar genotypes. GCA and SCA effects were
significant for grain yield (GY). Based on significant positive GCA
effects, the lines derived from LSC could be used as parent in crosses
to increase GY. The maximum best- parent heterosis values and
highest SCA effects resulted from crosses B73 × MO17 and A679 ×
MO17 for GY. The best heterotic patterns were LSC × RYD, which
would be potentially useful in maize breeding programs to obtain
high-yielding hybrids in the same climate of Iran.