Abstract: The transient analysis of a queuing system with fixed-size batch Poisson arrivals and a single server with exponential service times is presented. The focus of the paper is on the use of the functions that arise in the analysis of the transient behaviour of the queuing system. These functions are shown to be a generalization of the modified Bessel functions of the first kind, with the batch size B as the generalizing parameter. Results for the case of single-packet arrivals are obtained first. The similarities between the two families of functions are then used to obtain results for the general case of batch arrival queue with a batch size larger than one.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: This paper presents the results of an experimental study on the performance of a triboelectric separator of plastic mixtures used for recycling. The separator consists of four cylindrical electrodes. The principle behind the separation technique is based on the difference in the Coulomb force acting on the plastic particles after triboelectric charging. The separation of mixtures of acrylonitrile butadiene styrene (ABS) and polystyrene (PS) using this method was studied. The effects of the triboelectric charging time and applied voltage on the separation efficiency were investigated. The experimental results confirm that it is possible to obtain a high purity and recovery rate for the initial compositions considered in this study.
Abstract: The Yazd-Ardakan basin in Central Iran has two separated aquifers. The shallow unconfined aquifer is supplies 40 Qanats. The deep saturated confined aquifer is the main water storage. Due to over-withdrawal, water table has been decreasing during last 25 years. Recent study shows that the shortage of the aquifer is about 16 meters and land subsidence is 0.5 - 1.2 meters. Long deep cracks are found just above the aquifer and devour the irrigation water and floods. Although the most cracks direction is NW-SE and could be compared to the main direction of YA basin, there is no direct evidence for relation between land subsidence and the huge cracks. Large-scale water pumping has been decreased the water pressure in aquifer. The pressure decline disturbed the balance and increased the pressure of overlying sediments. So porosity decreased and compaction started. Then, sediments compaction developed and made land subsidence and some huge cracks slowly.
Abstract: Due to their high power-to-weight ratio and low cost,
pneumatic actuators are attractive for robotics and automation
applications; however, achieving fast and accurate control of their
position have been known as a complex control problem. A
methodology for obtaining high position accuracy with a linear
pneumatic actuator is presented. During experimentation with a
number of PID classical control approaches over many operations of
the pneumatic system, the need for frequent manual re-tuning of the
controller could not be eliminated. The reason for this problem is
thermal and energy losses inside the cylinder body due to the
complex friction forces developed by the piston displacements.
Although PD controllers performed very well over short periods, it
was necessary in our research project to introduce some form of
automatic gain-scheduling to achieve good long-term performance.
We chose a fuzzy logic system to do this, which proved to be an
easily designed and robust approach. Since the PD approach showed
very good behaviour in terms of position accuracy and settling time,
it was incorporated into a modified form of the 1st order Tagaki-
Sugeno fuzzy method to build an overall controller. This fuzzy gainscheduler
uses an input variable which automatically changes the PD
gain values of the controller according to the frequency of repeated
system operations. Performance of the new controller was
significantly improved and the need for manual re-tuning was
eliminated without a decrease in performance. The performance of
the controller operating with the above method is going to be tested
through a high-speed web network (GRID) for research purposes.
Abstract: There is need to explore emerging technologies based on carbon nanotube electronics as the MOS technology is approaching its limits. As MOS devices scale to the nano ranges, increased short channel effects and process variations considerably effect device and circuit designs. As a promising new transistor, the Carbon Nanotube Field Effect Transistor(CNTFET) avoids most of the fundamental limitations of the Traditional MOSFET devices. In this paper we present the analysis and comparision of a Carbon Nanotube FET(CNTFET) based 10(A current mirror with MOSFET for 32nm technology node. The comparision shows the superiority of the former in terms of 97% increase in output resistance,24% decrease in power dissipation and 40% decrease in minimum voltage required for constant saturation current. Furthermore the effect on performance of current mirror due to change in chirality vector of CNT has also been investigated. The circuit simulations are carried out using HSPICE model.
Abstract: Delay-Tolerant Networks (DTNs) are sparse, wireless
networks where disconnections are common due to host mobility and
low node density. The Message Ferrying (MF) scheme is a mobilityassisted
paradigm to improve connectivity in DTN-like networks. A
ferry or message ferry is a special node in the network which has
a per-determined route in the deployed area and relays messages
between mobile hosts (MHs) which are intermittently connected.
Increased contact opportunities among mobile hosts and the ferry
improve the performance of the network, both in terms of message
delivery ratio and average end-end delay. However, due to the inherent
mobility of mobile hosts and pre-determined periodicity of the
message ferry, mobile hosts may often -miss- contact opportunities
with a ferry. In this paper, we propose the combination of stationary
ferry access points (FAPs) with MF routing to increase contact
opportunities between mobile hosts and the MF and consequently
improve the performance of the DTN. We also propose several
placement models for deploying FAPs on MF routes. We evaluate the
performance of the FAP placement models through comprehensive
simulation. Our findings show that FAPs do improve the performance
of MF-assisted DTNs and symmetric placement of FAPs outperforms
other placement strategies.
Abstract: Pentachlorophenol (PCP) is a polychlorinated
aromatic compound that is widespread in industrial effluents and is
considered to be a serious pollutant. Among the variety of industrial
effluents encountered, effluents from tanning industry are very
important and have a serious pollution potential. PCP is also formed
unintentionally in effluents of paper and pulp industries. It is highly
persistent in soils and is lethal to a wide variety of beneficial
microorganisms and insects, human beings and animals. The natural
processes that breakdown toxic chemicals in the environment have
become the focus of much attention to develop safe and environmentfriendly
deactivation technologies. Microbes and plants are among
the most important biological agents that remove and degrade waste
materials to enable their recycling in the environment. The present
investigation was carried out with the aim of developing a microbial
system for bioremediation of PCP polluted soils. A number of plant
species were evaluated for their ability to tolerate different
concentrations of pentachlorophenol (PCP) in the soil. The
experiment was conducted for 30 days under pot culture conditions.
The toxic effect of PCP on plants was studied by monitoring seed
germination, plant growth and biomass. As the concentration of PCP
was increased to 50 ppm, the inhibition of seed germination, plant
growth and biomass was also increased. Although PCP had a
negative effect on all plant species tested, maize and groundnut
showed the maximum tolerance to PCP. Other tolerating crops
included wheat, safflower, sunflower, and soybean. From the
rhizosphere soil of the tolerant seedlings, as many as twenty seven
PCP tolerant bacteria were isolated. From soybean, 8; sunflower, 3;
safflower 8; maize 2; groundnut and wheat, 3 each isolates were
made. They were screened for their PCP degradation potentials.
HPLC analyses of PCP degradation revealed that the isolate MAZ-2
degraded PCP completely. The isolate MAZ-1 was the next best
isolate with 90 per cent PCP degradation. These strains hold promise
to be used in the bioremediation of PCP polluted soils.
Abstract: The new semi-experimental method for simulation of
the turbine flow meters rotation in the transitional flow has been
developed. The method is based on the experimentally established
exponential low of changing of dimensionless relative turbine gas
meter rotation frequency and meter inertia time constant. For
experimental evaluation of the meter time constant special facility
has been developed. The facility ensures instant switching of turbine
meter under test from one channel to the other channel with different
flow rate and measuring the meter response. The developed method
can be used for evaluation and predication of the turbine meters
response and dynamic error in the transitional flow with any arbitrary
law of flow rate changing. The examples of the method application
are presented.
Abstract: In this paper, a parametric experimental study for producing paving blocks using fine and coarse waste glass is presented. Some of the physical and mechanical properties of paving blocks having various levels of fine glass (FG) and coarse glass (CG) replacements with fine aggregate (FA) are investigated. The test results show that the replacement of FG by FA at level of 20% by weight has a significant effect on the compressive strength, flexural strength, splitting tensile strength and abrasion resistance of the paving blocks as compared with the control sample because of puzzolanic nature of FG. The compressive strength, flexural strength, splitting tensile strength and abrasion resistance of the paving block samples in the FG replacement level of 20% are 69%, 90%, 47% and 15 % higher as compared with the control sample respectively. It is reported in the earlier works the replacement of FG by FA at level of 20% by weight suppress the alkali-silica reaction (ASR) in the concrete. The test results show that the FG at level of 20% has a potential to be used in the production of paving blocks. The beneficial effect on these properties of CG replacement with FA is little as compared with FG.
Abstract: In the paper a detailed analysis of the dynamic
response of a cooling tower shell to mining tremors originated from
two main regions of mining activity in Poland (Upper Silesian Coal
Basin and Legnica-Glogow Copper District) was presented. The
representative time histories registered in the both regions were used
as ground motion data in calculations of the dynamic response of the
structure. It was proved that the dynamic response of the shell is
strongly dependent not only on the level of vibration amplitudes but
on the dominant frequency range of the mining shock typical for the
mining region as well. Also a vertical component of vibrations
occurred to have considerable influence on the total dynamic
response of the shell. Finally, it turned out that non-uniformity of
kinematic excitation resulting from spatial variety of ground motion
plays a significant role in dynamic analysis of large-dimensional
shells under mining shocks.
Abstract: An implementation of current-mode multiphase sinusoidal oscillators is presented. Using CFTA-based lossy integrators, odd and odd/even phase systems can be realized with following advantages. The condition of oscillation and frequency of oscillation can be orthogonally tuned. The high output impedances facilitate easy driving an external load without additional current buffers. The proposed MSOs provide odd or even phase signals that are equally spaced in phase and equal amplitude. The circuit requires one CFTA, one resistor and one grounded capacitor per phase without additional current amplifier. The results of PSPICE simulations using CMOS CFTA are included to verify theory.
Abstract: This paper considers the integration of assembly
operations and product structure to Cellular Manufacturing System
(CMS) design so that to correct the drawbacks of previous researches
in the literature. For this purpose, a new mathematical model is
developed which dedicates machining and assembly operations to
manufacturing cells while the objective function is to minimize the
intercellular movements resulting due to both of them. A
linearization method is applied to achieve optimum solution through
solving aforementioned nonlinear model by common programming
language such as Lingo. Then, using different examples and
comparing the results, the importance of integrating assembly
considerations is demonstrated.
Abstract: Due to the increasing penetration of wind energy, it is
necessary to possess design tools that are able to simulate the impact
of these installations in utility grids. In order to provide a net
contribution to this issue a detailed wind park model has been
developed and is briefly presented. However, the computational costs
associated with the performance of such a detailed model in
describing the behavior of a wind park composed by a considerable
number of units may render its practical application very difficult. To
overcome this problem integral manifolds theory has been applied to
reduce the order of the detailed wind park model, and therefore
create the conditions for the development of a dynamic equivalent
which is able to retain the relevant dynamics with respect to the
existing a.c. system. In this paper integral manifold method has been
introduced for order reduction. Simulation results of the proposed
method represents that integral manifold method results fit the
detailed model results with a higher precision than singular
perturbation method.
Abstract: In this paper, the problem of estimating the optimal
radio capacity of a single-cell spread spectrum (SS) multiple-inputmultiple-
output (MIMO) system operating in a Rayleigh fading environment
is examined. The optimisation between the radio capacity
and the theoretically achievable average channel capacity (in the
sense of information theory) per user of a MIMO single-cell SS system
operating in a Rayleigh fading environment is presented. Then,
the spectral efficiency is estimated in terms of the achievable average
channel capacity per user, during the operation over a broadcast
time-varying link, and leads to a simple novel-closed form expression
for the optimal radio capacity value based on the maximization
of the achieved spectral efficiency. Numerical results are presented to
illustrate the proposed analysis.
Abstract: Chicken feathers were used as biosorbent for Pb
removal from aqueous solution. In this paper, the kinetics and
equilibrium studies at several pH, temperature, and metal
concentration values are reported. For tested conditions, the Pb
sorption capacity of this poultry waste ranged from 0.8 to 8.3 mg/g.
Optimal conditions for Pb removal by chicken feathers have been
identified. Pseudo-first order and pseudo-second order equations
were used to analyze the experimental data. In addition, the sorption
isotherms were fitted to classical Langmuir and Freundlich models.
Finally, thermodynamic parameters for the sorption process have
been determined. In summary, the results showed that chicken
feathers are an alternative and promising sorbent for the treatment of
effluents polluted by Pb ions.
Abstract: Study is on the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. The effects of the FGM configuration are studied by studying the frequencies of FG cylindrical shells. In this case FG cylindrical shell has Nickel on its inner surface and stainless steel on its outer surface. The study is carried out based on third order shear deformation shell theory. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of configurations of the constituent materials on the frequencies. The properties are graded in the thickness direction according to the volume fraction power-law distribution. Results are presented on the frequency characteristics, the influence of the constituent various volume fractions on the frequencies.
Abstract: The customary practice of identifying industrial sickness is a set traditional techniques which rely upon a range of manual monitoring and compilation of financial records. It makes the process tedious, time consuming and often are susceptible to manipulation. Therefore, certain readily available tools are required which can deal with such uncertain situations arising out of industrial sickness. It is more significant for a country like India where the fruits of development are rarely equally distributed. In this paper, we propose an approach based on Artificial Neural Network (ANN) to deal with industrial sickness with specific focus on a few such units taken from a less developed north-east (NE) Indian state like Assam. The proposed system provides decision regarding industrial sickness using eight different parameters which are directly related to the stages of sickness of such units. The mechanism primarily uses certain signals and symptoms of industrial health to decide upon the state of a unit. Specifically, we formulate an ANN based block with data obtained from a few selected units of Assam so that required decisions related to industrial health could be taken. The system thus formulated could become an important part of planning and development. It can also contribute towards computerization of decision support systems related to industrial health and help in better management.
Abstract: Titanium nitride (TiN) has been synthesized using the
sheet plasma negative ion source (SPNIS). The parameters used for
its effective synthesis has been determined from previous
experiments and studies. In this study, further enhancement of the
deposition rate of TiN synthesis and advancement of the SPNIS
operation is presented. This is primarily achieved by the addition of
Sm-Co permanent magnets and a modification of the configuration in
the TiN deposition process. The magnetic enhancement is aimed at
optimizing the sputtering rate and the sputtering yield of the process.
The Sm-Co permanent magnets are placed below the Ti target for
better sputtering by argon. The Ti target is biased from –250V to –
350V and is sputtered by Ar plasma produced at discharge current of
2.5–4A and discharge potential of 60–90V. Steel substrates of
dimensions 20x20x0.5mm3 were prepared with N2:Ar volumetric
ratios of 1:3, 1:5 and 1:10. Ocular inspection of samples exhibit
bright gold color associated with TiN. XRD characterization
confirmed the effective TiN synthesis as all samples exhibit the (200)
and (311) peaks of TiN and the non-stoichiometric Ti2N (220) facet.
Cross-sectional SEM results showed increase in the TiN deposition
rate of up to 0.35μm/min. This doubles what was previously obtained
[1]. Scanning electron micrograph results give a comparative
morphological picture of the samples. Vickers hardness results gave
the largest hardness value of 21.094GPa.
Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.