Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.
Abstract: Statistical learning theory was developed by Vapnik. It
is a learning theory based on Vapnik-Chervonenkis dimension. It also
has been used in learning models as good analytical tools. In general, a
learning theory has had several problems. Some of them are local
optima and over-fitting problems. As well, statistical learning theory
has same problems because the kernel type, kernel parameters, and
regularization constant C are determined subjectively by the art of
researchers. So, we propose an evolutionary statistical learning theory
to settle the problems of original statistical learning theory.
Combining evolutionary computing into statistical learning theory,
our theory is constructed. We verify improved performances of an
evolutionary statistical learning theory using data sets from KDD cup.
Abstract: The authors present an algorithm for order reduction of linear dynamic systems using the combined advantages of stability equation method and the error minimization by Genetic algorithm. The denominator of the reduced order model is obtained by the stability equation method and the numerator terms of the lower order transfer function are determined by minimizing the integral square error between the transient responses of original and reduced order models using Genetic algorithm. The reduction procedure is simple and computer oriented. It is shown that the algorithm has several advantages, e.g. the reduced order models retain the steady-state value and stability of the original system. The proposed algorithm has also been extended for the order reduction of linear multivariable systems. Two numerical examples are solved to illustrate the superiority of the algorithm over some existing ones including one example of multivariable system.
Abstract: Phishing scheme is a new emerged security issue of
E-Commerce Crime in globalization. In this paper, the legal scaffold
of Malaysia, United States and United Kingdom are analyzed and
followed by discussion on critical issues that rose due to phishing
activities. The result revealed that inadequacy of current legal
framework is the main challenge to govern this epidemic. However,
lack of awareness among consumers, crisis on merchant-s
responsibility and lack of intrusion reports and incentive arrangement
contributes to phishing proliferating. Prevention is always better than
curb. By the end of this paper, some best practices for consumers and
corporations are suggested.
Abstract: In this paper we designed and implemented a new
ensemble of classifiers based on a sequence of classifiers which were
specialized in regions of the training dataset where errors of its
trained homologous are concentrated. In order to separate this
regions, and to determine the aptitude of each classifier to properly
respond to a new case, it was used another set of classifiers built
hierarchically. We explored a selection based variant to combine the
base classifiers. We validated this model with different base
classifiers using 37 training datasets. It was carried out a statistical
comparison of these models with the well known Bagging and
Boosting, obtaining significantly superior results with the
hierarchical ensemble using Multilayer Perceptron as base classifier.
Therefore, we demonstrated the efficacy of the proposed ensemble,
as well as its applicability to general problems.
Abstract: Shortening of natural resources will impose greater
limitations of electric energy consumption in various fields including
water treatment technologies. Small water treatment installations
supplied with electric energy from solar sources are perfect example of
zero-emission technology. Possibility of solar energy application, as
one of the alternative energy resources for decontamination processes
is strongly dependent on geographical location. Various examples of
solar driven water purification systems are given and design of
solar-water treatment installation based on ozone for the geographical
conditions in Poland are presented.
Abstract: Recycling of aluminum alloys often decrease fluidity,
consequently influence the castability of the alloy. In this study, the
fluidity of Al-Zn alloys, such as the standard A713 alloy with and
without scrap addition has been investigated. The scrap added was
comprised of contaminated alloy turning chips. Fluidity
measurements were performed with double spiral fluidity test
consisting of gravity casting of double spirals in green sand moulds
with good reproducibility. The influence of recycled alloy on fluidity
has been compared with that of the virgin alloy and the results
showed that the fluidity decreased with the increase in recycled alloy
at minimum pouring temperatures. Interestingly, an appreciable
improvement in the fluidity was observed at maximum pouring
temperature, especially for coated spirals.
Abstract: Acid rain occurs when sulphur dioxide (SO2) and
nitrogen oxides (Nox) gases react in the atmosphere with water,
oxygen, and other chemicals to form various acidic compounds. The
result is a mild solution of sulfuric acid and nitric acid. Soil has a
greater buffering capacity than aquatic systems. However excessive
amount of acids introduced by acid rains may disturb the entire soil
chemistry. Acidity and harmful action of toxic elements damage
vegetation while susceptible microbial species are eliminated. In
present study, the effects of simulated sulphuric acid and nitric acid
rains were investigated on crop Glycine max. The effect of acid rain
on change in soil fertility was detected in which pH of control sample
was 6.5 and pH of 1%H2SO4 and 1%HNO3 were 3.5. Nitrogen nitrate
in soil was high in 1% HNO3 treated soil & Control sample.
Ammonium nitrogen in soil was low in 1% HNO3 & H2SO4 treated
soil. Ammonium nitrogen was medium in control and other samples.
The effect of acid rain on seed germination on 3rd day of germination
control sample growth was 7 cm, 0.1% HNO3 was 8cm, and 0.001%
HNO3 & 0.001% H2SO4 was 6cm each. On 10th day fungal growth
was observed in 1% and 0.1%H2SO4 concentrations, when all plants
were dead. The effect of acid rain on crop productivity was
investigated on 3rd day roots were developed in plants. On12th day
Glycine max showed more growth in 0.1% HNO3, 0.001% HNO3 and
0.001% H2SO4 treated plants growth were same as compare to control
plants. On 20th day development of discoloration of plant pigments
were observed on acid treated plants leaves. On 38th day, 0.1, 0.001%
HNO3 and 0.1, 0.001% H2SO4 treated plants and control plants were
showing flower growth. On 42th day, acid treated Glycine max variety
and control plants were showed seeds on plants. In Glycine max
variety 0.1, 0.001% H2SO4, 0.1, 0.001% HNO3 treated plants were
dead on 46th day and fungal growth was observed. The toxicological
study was carried out on Glycine max plants exposed to 1% HNO3
cells were damaged more than 1% H2SO4. Leaf sections exposed to
0.001% HNO3 & H2SO4 showed less damaged of cells and
pigmentation observed in entire slide when compare with control
plant. The soil analysis was done to find microorganisms in HNO3 &
H2SO4 treated Glycine max and control plants. No microorganism
growth was observed in 1% HNO3 & H2SO4 but control plant showed
microbial growth.
Abstract: Removal of a reactive dye (Reactive blue 4) by
adsorption utilizing waste aluminium hydroxide sludge as an
adsorbent was investigated. The removal of the dye was optimized
using response surface methodology (RSM). In the RSM
experiments; initial dye concentration, adsorbent concentration and
contact time were critical parameters. RSM experiments were
performed at the range of initial dye concentration 31.82-368.18
mg/L, adsorbent concentration 3.18-36.82 g/L, contact time 15.82-
56.18 h. Optimum initial dye concentration, adsorbent concentration
and contact time were obtained as 108.83 mg/L, 29.36 g/L and 33.57
h respectively. At these conditions, maximum removal of the dye was
obtained as 95%. The experiments were performed at the optimum
conditions to verify these results and the same results were obtained.
Abstract: This paper reports the fatigue crack growth behaviour
of gas tungsten arc, electron beam and laser beam welded Ti-6Al-4V
titanium alloy. Centre cracked tensile specimens were prepared to
evaluate the fatigue crack growth behaviour. A 100kN servo
hydraulic controlled fatigue testing machine was used under constant
amplitude uniaxial tensile load (stress ratio of 0.1 and frequency of
10 Hz). Crack growth curves were plotted and crack growth
parameters (exponent and intercept) were evaluated. Critical and
threshold stress intensity factor ranges were also evaluated. Fatigue
crack growth behaviour of welds was correlated with mechanical
properties and microstructural characteristics of welds. Of the three
joints, the joint fabricated by laser beam welding exhibited higher
fatigue crack growth resistance due to the presence of fine lamellar
microstructure in the weld metal.
Abstract: Transmission network expansion planning (TNEP) is
a basic part of power system planning that determines where, when
and how many new transmission lines should be added to the
network. Up till now, various methods have been presented to solve
the static transmission network expansion planning (STNEP)
problem. But in all of these methods, transmission expansion
planning considering network adequacy restriction has not been
investigated. Thus, in this paper, STNEP problem is being studied
considering network adequacy restriction using discrete particle
swarm optimization (DPSO) algorithm. The goal of this paper is
obtaining a configuration for network expansion with lowest
expansion cost and a specific adequacy. The proposed idea has been
tested on the Garvers network and compared with the decimal
codification genetic algorithm (DCGA). The results show that the
network will possess maximum efficiency economically. Also, it is
shown that precision and convergence speed of the proposed DPSO
based method for the solution of the STNEP problem is more than
DCGA approach.
Abstract: LES with mixed subgrid-scale model has been used to
simulate aerodynamic performance of hypersonic configuration. The
simulation was conducted to replicate conditions and geometry of a
model which has been previously tested. LES Model has been
successful in predict pressure coefficient with the max error 1.5%
besides afterbody. But in the high Mach number condition, it is poor in
predict ability and product 12.5% error. The calculation error are
mainly conducted by the distribution swirling. The fact of poor ability
in the high Mach number and afterbody region indicated that the
mixed subgrid-scale model should be improved in large eddied
especially in hypersonic separate region. In the condition of attach and
sideslip flight, the calculation results have waves. LES are successful
in the prediction the pressure wave in hypersonic flow.
Abstract: This paper describes the design of a real-time audiorange
digital oscilloscope and its implementation in 90nm CMOS
FPGA platform. The design consists of sample and hold circuits,
A/D conversion, audio and video processing, on-chip RAM, clock
generation and control logic. The design of internal blocks and
modules in 90nm devices in an FPGA is elaborated. Also the key
features and their implementation algorithms are presented.
Finally, the timing waveforms and simulation results are put
forward.
Abstract: Bendability is constrained by maximum top roller
load imparting capacity of the machine. Maximum load is
encountered during the edge pre-bending stage of roller bending.
Capacity of 3-roller plate bending machine is specified by
maximum thickness and minimum shell diameter combinations that
can be pre-bend for given plate material of maximum width.
Commercially available plate width or width of the plate that can be
accommodated on machine decides the maximum rolling width.
Original equipment manufacturers (OEM) provide the machine
capacity chart based on reference material considering perfectly
plastic material model. Reported work shows the bendability analysis
of heavy duty 3-roller plate bending machine. The input variables for
the industry are plate thickness, shell diameter and material property
parameters, as it is fixed by the design. Analytical models of
equivalent thickness, equivalent width and maximum width based on
power law material model were derived to study the bendability.
Equation of maximum width provides bendability for designed
configuration i.e. material property, shell diameter and thickness
combinations within the machine limitations. Equivalent thicknesses
based on perfectly plastic and power law material model were
compared for four different materials grades of C-Mn steel in order
to predict the bend-ability. Effect of top roller offset on the
bendability at maximum top roller load imparting capacity is
reported.
Abstract: Problems on algebraical polynomials appear in many fields of mathematics and computer science. Especially the task of determining the roots of polynomials has been frequently investigated.Nonetheless, the task of locating the zeros of complex polynomials is still challenging. In this paper we deal with the location of zeros of univariate complex polynomials. We prove some novel upper bounds for the moduli of the zeros of complex polynomials. That means, we provide disks in the complex plane where all zeros of a complex polynomial are situated. Such bounds are extremely useful for obtaining a priori assertations regarding the location of zeros of polynomials. Based on the proven bounds and a test set of polynomials, we present an experimental study to examine which bound is optimal.
Abstract: Distant-talking voice-based HCI system suffers from
performance degradation due to mismatch between the acoustic
speech (runtime) and the acoustic model (training). Mismatch is
caused by the change in the power of the speech signal as observed at
the microphones. This change is greatly influenced by the change in
distance, affecting speech dynamics inside the room before reaching
the microphones. Moreover, as the speech signal is reflected, its
acoustical characteristic is also altered by the room properties. In
general, power mismatch due to distance is a complex problem. This
paper presents a novel approach in dealing with distance-induced
mismatch by intelligently sensing instantaneous voice power variation
and compensating model parameters. First, the distant-talking speech
signal is processed through microphone array processing, and the
corresponding distance information is extracted. Distance-sensitive
Gaussian Mixture Models (GMMs), pre-trained to capture both
speech power and room property are used to predict the optimal
distance of the speech source. Consequently, pre-computed statistic
priors corresponding to the optimal distance is selected to correct
the statistics of the generic model which was frozen during training.
Thus, model combinatorics are post-conditioned to match the power
of instantaneous speech acoustics at runtime. This results to an
improved likelihood in predicting the correct speech command at
farther distances. We experiment using real data recorded inside two
rooms. Experimental evaluation shows voice recognition performance
using our method is more robust to the change in distance compared
to the conventional approach. In our experiment, under the most
acoustically challenging environment (i.e., Room 2: 2.5 meters), our
method achieved 24.2% improvement in recognition performance
against the best-performing conventional method.
Abstract: Nowadays, with the emerging of the new applications
like robot control in image processing, artificial vision for visual
servoing is a rapidly growing discipline and Human-machine
interaction plays a significant role for controlling the robot. This
paper presents a new algorithm based on spatio-temporal volumes for
visual servoing aims to control robots. In this algorithm, after
applying necessary pre-processing on video frames, a spatio-temporal
volume is constructed for each gesture and feature vector is extracted.
These volumes are then analyzed for matching in two consecutive
stages. For hand gesture recognition and classification we tested
different classifiers including k-Nearest neighbor, learning vector
quantization and back propagation neural networks. We tested the
proposed algorithm with the collected data set and results showed the
correct gesture recognition rate of 99.58 percent. We also tested the
algorithm with noisy images and algorithm showed the correct
recognition rate of 97.92 percent in noisy images.
Abstract: Several works regarding facial recognition have dealt with methods which identify isolated characteristics of the face or with templates which encompass several regions of it. In this paper a new technique which approaches the problem holistically dispensing with the need to identify geometrical characteristics or regions of the face is introduced. The characterization of a face is achieved by randomly sampling selected attributes of the pixels of its image. From this information we construct a set of data, which correspond to the values of low frequencies, gradient, entropy and another several characteristics of pixel of the image. Generating a set of “p" variables. The multivariate data set with different polynomials minimizing the data fitness error in the minimax sense (L∞ - Norm) is approximated. With the use of a Genetic Algorithm (GA) it is able to circumvent the problem of dimensionality inherent to higher degree polynomial approximations. The GA yields the degree and values of a set of coefficients of the polynomials approximating of the image of a face. By finding a family of characteristic polynomials from several variables (pixel characteristics) for each face (say Fi ) in the data base through a resampling process the system in use, is trained. A face (say F ) is recognized by finding its characteristic polynomials and using an AdaBoost Classifier from F -s polynomials to each of the Fi -s polynomials. The winner is the polynomial family closer to F -s corresponding to target face in data base.
Abstract: Facility location problem involves locating a facility
to optimize some performance measures. Location of a public facility
to serve the community, such as a fire station, significantly affects its
service quality. Main objective in locating a fire station is to
minimize the response time, which is the time duration between
receiving a call and reaching the place of incident. In metropolitan
areas, fire vehicles need to cross highways and other traffic obstacles
through some obstacle-overcoming points which delay the response
time. In this paper, fire station location problem is analyzed.
Simulation models are developed for the location problems which
involve obstacles. Particular case problems are analyzed and the
results are presented.
Abstract: In the last two decades radiofrequency ablation (RFA)
has been considered a promising medical procedure for the treatment
of primary and secondary malignancies. However, the needle-based
electrodes so far developed for this kind of treatment are not suitable
for the thermal ablation of tumors located in hollow organs like
esophagus, colon or bile duct. In this work a tubular electrode
solution is presented. Numerical and experimental analyses were
performed to characterize the volume of the lesion induced. Results
show that this kind of electrode is a feasible solution and numerical
simulation might provide a tool for planning RFA procedure with
some accuracy.