Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: The education sector is constantly faced with rapid
changes in technologies in terms of ensuring that the curriculum is up
to date and in terms of making sure that students are aware of these
technological changes. This challenge can be seen as the motivation
for this study, which is to examine the factors affecting computing
students’ awareness of the latest Information Technologies (ICTs).
The aim of this study is divided into two sub-objectives which are:
the selection of relevant theories and the design of a conceptual
model to support it as well as the empirical testing of the designed
model. The first objective is achieved by a review of existing
literature on technology adoption theories and models. The second
objective is achieved using a survey of computing students in the four
universities of the KwaZulu-Natal province of South Africa. Data
collected from this survey is analyzed using Statistical package for
the Social Science (SPSS) using descriptive statistics, ANOVA and
Pearson correlations. The main hypothesis of this study is that there is
a relationship between the demographics and the prior conditions of
the computing students and their awareness of general ICT trends and
of Digital Switch Over (DSO) a new technology which involves the
change from analog to digital television broadcasting in order to
achieve improved spectrum efficiency. The prior conditions of the
computing students that were considered in this study are students’
perceived exposure to career guidance and students’ perceived
curriculum currency. The results of this study confirm that gender,
ethnicity, and high school computing course affect students’
perceived curriculum currency while high school location affects
students’ awareness of DSO. The results of this study also confirm
that there is a relationship between students prior conditions and their
awareness of general ICT trends and DSO in particular.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: This study presents experimental and optimization of
nanoparticle mass concentration and heat input based on the total
thermal resistance (Rth) of loop heat pipe (LHP), employed for PCCPU
cooling. In this study, silica nanoparticles (SiO2) in water with
particle mass concentration ranged from 0% (pure water) to 1% is
considered as the working fluid within the LHP. The experimental
design and optimization is accomplished by the design of
experimental tool, Response Surface Methodology (RSM). The
results show that the nanoparticle mass concentration and the heat
input have significant effect on the Rth of LHP. For a given heat
input, the Rth is found to decrease with the increase of the
nanoparticle mass concentration up to 0.5% and increased thereafter.
It is also found that the Rth is decreased when the heat input is
increased from 20W to 60W. The results are optimized with the
objective of minimizing the Rth, using Design-Expert software, and
the optimized nanoparticle mass concentration and heat input are
0.48% and 59.97W, respectively, the minimum thermal resistance
being 2.66 (ºC/W).
Abstract: Non-linear dynamic time history analysis is
considered as the most advanced and comprehensive analytical
method for evaluating the seismic response and performance of
multi-degree-of-freedom building structures under the influence of
earthquake ground motions. However, effective and accurate
application of the method requires the implementation of advanced
hysteretic constitutive models of the various structural components
including masonry infill panels. Sophisticated computational research
tools that incorporate realistic hysteresis models for non-linear
dynamic time-history analysis are not popular among the professional
engineers as they are not only difficult to access but also complex and
time-consuming to use. In addition, commercial computer programs
for structural analysis and design that are acceptable to practicing
engineers do not generally integrate advanced hysteretic models
which can accurately simulate the hysteresis behavior of structural
elements with a realistic representation of strength degradation,
stiffness deterioration, energy dissipation and ‘pinching’ under cyclic
load reversals in the inelastic range of behavior. In this scenario,
push-over or non-linear static analysis methods have gained
significant popularity, as they can be employed to assess the seismic
performance of building structures while avoiding the complexities
and difficulties associated with non-linear dynamic time-history
analysis. “Push-over” or non-linear static analysis offers a practical
and efficient alternative to non-linear dynamic time-history analysis
for rationally evaluating the seismic demands. The present paper is
based on the analytical investigation of the effect of distribution of
masonry infill panels over the elevation of planar masonry infilled
reinforced concrete [R/C] frames on the seismic demands using the
capacity spectrum procedures implementing nonlinear static analysis
[pushover analysis] in conjunction with the response spectrum
concept. An important objective of the present study is to numerically
evaluate the adequacy of the capacity spectrum method using
pushover analysis for performance based design of masonry infilled
R/C frames for near-field earthquake ground motions.
Abstract: This paper addresses the problem of offline path
planning for Unmanned Aerial Vehicles (UAVs) in complex threedimensional
environment with obstacles, which is modelled by 3D
Cartesian grid system. Path planning for UAVs require the
computational intelligence methods to move aerial vehicles along the
flight path effectively to target while avoiding obstacles. In this paper
Modified Particle Swarm Optimization (MPSO) algorithm is applied
to generate the optimal collision free 3D flight path for UAV. The
simulations results clearly demonstrate effectiveness of the proposed
algorithm in guiding UAV to the final destination by providing
optimal feasible path quickly and effectively.
Abstract: The paper is focused to the evaluation railway tracks
in the Slovakia by using Multi-Criteria method. Evaluation of railway
tracks has important impacts for the assessment of investment in
technical equipment. Evaluation of railway tracks also has an
important impact for the allocation of marshalling yards. Marshalling
yards are in transport model as centers for the operation assigned
catchment area. This model is one of the effective ways to meet the
development strategy of the European Community's railways. By
applying this model in practice, a transport company can guarantee a
higher quality of service and then expect an increase in performance.
The model is also applicable to other rail networks. This model
supplements a theoretical problem of train formation problem of new
ways of looking at evaluation of factors affecting the organization of
wagon flows.
Abstract: The article includes the results and conclusions from
empirical researches that had been done. The research focuses on the
impact of investments made in small and medium-sized enterprises
financed from EU funds on the competitiveness of these companies.
The researches includes financial results in sales revenue and net
income, expenses, and many other new products/services on offer,
higher quality products and services, more modern methods of
production, innovation in management processes, increase in the
number of customers, increase in market share, increase in
profitability of production and provision of services. The main
conclusions are that, companies with direct investments under this
measure shall apply the modern methods of production. The
consequence of this is to increase the quality of our products and
services. Furthermore, both small and medium-sized enterprises have
introduced new products and services. Investments were carried out,
thus enabling better work organization in enterprises. Entrepreneurs
would guarantee higher quality of service, which would result in
better relationships with their customers, what is more, noting the rise
in number of clients. More than half of the companies indicated that
the investments contributed to the increase in market share. Same
thing as for market reach and brand recognition of particular
company. An interesting finding is that, investments in small
enterprises were more effective than medium-sized enterprises.
Abstract: The wider growing Finite Element Method (FEM)
application is caused by its benefits of cost saving and environment
friendly. Also, by using FEM a deep understanding of certain
phenomenon can be achieved. This paper observed the role of
material properties and volumetric change when Solid State Phase
Transformation (SSPT) takes place in residual stress formation due to
a welding process of ferritic steels through coupled Thermo-
Metallurgy-Mechanical (TMM) analysis. The correctness of FEM residual stress prediction was validated by
experiment. From parametric study of the FEM model, it can be
concluded that the material properties change tend to over-predicts
residual stress in the weld center whilst volumetric change tend to
underestimates it. The best final result is the compromise of both by
incorporates them in the model which has a better result compared to
a model without SSPT.
Abstract: Many herbal medicinal products are considered
potential anti-hypercholesterolemic agents with encouraging safety
profiles, however only a limited amount of clinical research exists to
support their efficacy. The present study was designed to compare the
antihypercholesterolemic and antioxidant activities of the crude
ethanolic extracts of Citrus reticulata fruit peel, Zingiber officinale
rhizome and Sesamum indicum seeds. Forty-five rats were used throughout the experiment which are
extended for four weeks. These were divided into nine groups, five
rats per each group as follows; group 1 was the normal control group
(rats only fed standard normal rat diet), group 2 was the
hypercholesterolemic control group (rats fed only
hypercholesterolemic diet which contained 1% cholesterol plus 10%
saturated animal fat added to the normal rat diet), groups 3 and 4
were fed hypercholesterolemic diet in addition to Citrus reticulata
ethanolic extract at doses of (250mg/kg (group 3) and 500mg/kg
(group 4)) administered daily via oral route, groups 5 and 6 were
given hypercholesterolemic diet in addition to Zingiber officinale
ethanolic extract at doses of (250mg/kg (group 5) and 500mg/kg
(group 6)) daily through oral route, groups 7 and 8 fed on
hypercholesterolemic diet in addition to Sesamum indicum ethanolic
extract at doses of (250mg/kg (group 7) and 500mg/kg (group 8))
daily orally; and group 9 rats were given hypercholesterolemic diet in
addition to atorvastatin (0.18mg/kg) daily via oral route as a standard
reference antihypercholesterolemic drug. Blood samples from all
groups were drawn from the retro-orbital venous plexus four weeks
following treatment after overnight fasting and the lipid profile (total
cholesterol (TC), high density lipoprotein-cholesterol (HDL-C), low
density lipoprotein-cholesterol (LDL-C) and triglyceride levels) were
measured and the risk ratio (TC/HDL-C) was assessed. The
antioxidant activity of the three plants extracts was determined using
DPPH free-radical antioxidant assay. Results of in vivo and in vitro
antihypercholesterolemic and antioxidant assay respectively, revealed
that the three extracts possess comparable antioxidant and
antihypercholesterolemic activities.
Abstract: The contemporary battlefield creates a demand for
more costly and highly advanced munitions. Training personnel
responsible for operations as well as immediate execution of combat
tasks which engage real asset is unrealistic and economically not
feasible. Owing to a wide array of exploited simulators and various
types of imitators, it is possible to reduce the costs. One of the
effective elements of training, which can be applied in the training of
all service branches, is imitator of aerial targets. This research serves
as an introduction to the commencement of design analysis over a
real aerial target imitator. Within the project, the basic aerodynamic
calculations were made, which enabled to determine its geometry,
design layout, performance as well as mass balance of individual
components. The conducted calculations of the parameters of flight
characteristics come closer to the real performance of such
Unmanned Aerial Vehicles.
Abstract: Brain-Computer Interfaces (BCIs) measure brain
signals activity, intentionally and unintentionally induced by users,
and provides a communication channel without depending on the
brain’s normal peripheral nerves and muscles output pathway.
Feature Selection (FS) is a global optimization machine learning
problem that reduces features, removes irrelevant and noisy data
resulting in acceptable recognition accuracy. It is a vital step
affecting pattern recognition system performance. This study presents
a new Binary Particle Swarm Optimization (BPSO) based feature
selection algorithm. Multi-layer Perceptron Neural Network
(MLPNN) classifier with backpropagation training algorithm and
Levenberg-Marquardt training algorithm classify selected features.
Abstract: The purpose of the study was to examine lifelong
education for teachers as a tool for achieving effective teaching and
learning. Lifelong education enhances social inclusion, personal
development, citizenship, employability, teaching and learning,
community and the nation. It is imperative that the teacher needs to
update his knowledge regularly to be able to perform optimally, since
he has a major position in the inculcation of desirable elements in
students, and the challenges of lifelong education were also
discussed. Descriptive survey design was adopted for the study. A
simple random sampling technique was used to select 80 teachers as
sample from a population of 105 senior secondary school teachers in
Makurdi Local Government Area of Benue State. A 20-item self
designed questionnaire subjected to expert validation and reliability
was used to collect data. The reliability Alpha coefficient of 0.87 was
established using Cronbach’s Alpha technique, mean scores and
standard deviation were used to answer the 2 research questions
while chi-square was used to analyse data for the 2 null hypotheses,
which states that lifelong education for teachers is not a significant
tool for achieving effective teaching and lifelong education for
teachers does not significantly impact on effective learning. The
findings of the study revealed that, lifelong education for teachers can
be used as a tool for achieving effective teaching and learning, and
the study recommended among others that government, organizations
and individuals should in collaboration put lifelong education
programmes for teachers on the priority list. The paper concluded
that the strategic position of lifelong education for teachers towards
enhanced teaching, learning and the production of quality manpower
in the society makes it imperative for all hands to be on “deck” to
support the programme financially and otherwise.
Abstract: The use of magnesium alloys is limited due to their
susceptibility to corrosion although they have many attractive
physical and mechanical properties. To increase mechanical and
corrosion properties of these alloys, many deposition method and
coating types are used. Electroless Ni–B coatings have received
considerable interest recently due to its unique properties such as
cost-effectiveness, thickness uniformity, good wear resistance,
lubricity, good ductility and corrosion resistance, excellent
solderability and electrical properties and antibacterial property. In
this study, electroless Ni-B coating could been deposited on AZ91
magnesium alloy. The obtained coating exhibited a harder and
rougher structure than the substrate.
Abstract: In turbulent modern economy, the companies need to
properly manage their business processes. Well-defined and stable
business processes ensure security of crucial data and applications,
and provide a quality product or service to the end customer. On the
other side, constant changes on the market, new regulatory
provisions, and emerging new technologies require the need of
issuing prompt and effective changes of business process. In this
article, we explore the use of agile principles in working with
business process management (BPM) solutions. We deal with
difficulties in BPM development cycle, review the benefits of using
agility, and choose the basic agile principles that ensure the success
of a BPM project.
Abstract: In this paper genetic based test data compression is
targeted for improving the compression ratio and for reducing the
computation time. The genetic algorithm is based on extended pattern
run-length coding. The test set contains a large number of X value
that can be effectively exploited to improve the test data
compression. In this coding method, a reference pattern is set and its
compatibility is checked. For this process, a genetic algorithm is
proposed to reduce the computation time of encoding algorithm. This
coding technique encodes the 2n compatible pattern or the inversely
compatible pattern into a single test data segment or multiple test data
segment. The experimental result shows that the compression ratio
and computation time is reduced.
Abstract: Recent investigations have demonstrated the global
sea level rise due to climate change impacts. In this study, climate
changes study the effects of increasing water level in the strait of
Hormuz. The probable changes of sea level rise should be
investigated to employ the adaption strategies. The climatic output
data of a GCM (General Circulation Model) named CGCM3 under
climate change scenario of A1b and A2 were used. Among different
variables simulated by this model, those of maximum correlation
with sea level changes in the study region and least redundancy
among themselves were selected for sea level rise prediction by using
stepwise regression. One of models (Discrete Wavelet artificial
Neural Network) was developed to explore the relationship between
climatic variables and sea level changes. In these models, wavelet
was used to disaggregate the time series of input and output data into
different components and then ANN was used to relate the
disaggregated components of predictors and input parameters to each
other. The results showed in the Shahid Rajae Station for scenario
A1B sea level rise is among 64 to 75 cm and for the A2 Scenario sea
level rise is among 90 t0 105 cm. Furthermore, the result showed a
significant increase of sea level at the study region under climate
change impacts, which should be incorporated in coastal areas
management.
Abstract: The paper is focused on the operational model for
transport the single wagon consignments on railway network by
using two different models of train formation. The paper gives an
overview of possibilities of improving the quality of transport
services. Paper deals with two models used in problematic of train
formatting - time continuously and time discrete. By applying these
models in practice, the transport company can guarantee a higher
quality of service and expect increasing of transport performance.
The models are also applicable into others transport networks. The
models supplement a theoretical problem of train formation by new
ways of looking to affecting the organization of wagon flows.
Abstract: The ultimate purpose of this investigation was to
determine the teachers’ opinions as well as students’ opinions
towards the Adapted English Lessons. The subjects of the study were
5 Thai teachers, who teach English, and 85 Grade 10 mixed-ability
students at Triamudom Suksa Pattanakarn Ratchada School,
Bangkok, Thailand. The research instruments included questionnaires
and the informal interview. The data from the research instruments
was collected and analyzed concerning linguistic principles of
minimal pair and articulatory phonetics as well as teaching
techniques of mimicry-memorization; vocabulary substitution drills,
language pattern drills, reading comprehension exercise, practicing
listening, speaking and writing skill and communicative activities;
informal talk and free writing. The data was statistically compiled
according to an arithmetic percentage. The results showed that the
teachers and students have very highly positive opinions towards
adapting linguistic principles for teaching and learning phonological
accuracy. Teaching techniques provided in the Adapted English
Lessons can be used efficiently in the classroom. The teachers and
students have positive opinions towards them too.