Abstract: Fragility analysis is an effective tool for the seismic vulnerability assessment of civil structures in the last several years. The design of the expansion joints according to various bridge design codes is almost inconsistent, and only a few studies have focused on this problem so far. In this study, the influence of the expansion joint clearances between the girder ends and the abutment backwalls on the seismic fragility assessment of continuous integral bridge frames is investigated. The gaps (ranging from 60 mm, 150 mm, 250 mm and 350 mm) are designed by following two different bridge design code specifications, namely, Caltrans and Eurocode 8-2. Five bridge models are analyzed and compared. The first bridge model serves as a reference. This model uses three-dimensional reinforced concrete fiber beam-column elements with simplified supports at both ends of the girder. The other four models also employ reinforced concrete fiber beam-column elements but include the abutment backfill stiffness and four different gap values. The nonlinear time history analysis is performed. The artificial ground motion sets, which have the peak ground accelerations (PGAs) ranging from 0.1 g to 1.0 g with an increment of 0.05 g, are taken as input. The soil-structure interaction and the P-Δ effects are also included in the analysis. The component fragility curves in terms of the curvature ductility demand to the capacity ratio of the piers and the displacement demand to the capacity ratio of the abutment sliding bearings are established and compared. The system fragility curves are then obtained by combining the component fragility curves. Our results show that in the component fragility analysis, the reference bridge model exhibits a severe vulnerability compared to that of other sophisticated bridge models for all damage states. In the system fragility analysis, the reference curves illustrate a smaller damage probability in the earlier PGA ranges for the first three damage states, they then show a higher fragility compared to other curves in the larger PGA levels. In the fourth damage state, the reference curve has the smallest vulnerability. In both the component and the system fragility analysis, the same trend is found that the bridge models with smaller clearances exhibit a smaller fragility compared to that with larger openings. However, the bridge model with a maximum clearance still induces a minimum pounding force effect.
Abstract: During manned exploration of space, missions will require astronaut crewmembers to perform Extra Vehicular Activities (EVAs) for a variety of tasks. These EVAs take place after long periods of operations in space, and in and around unique vehicles, space structures and systems. Considering the remoteness and time spans in which these vehicles will operate, EVA system operations should utilize common worksites, tools and procedures as much as possible to increase the efficiency of training and proficiency in operations. All of the preparations need to be carried out based on studies of astronaut motions. Until now, development and training activities associated with the planned EVAs in Russian and U.S. space programs have relied almost exclusively on physical simulators. These experimental tests are expensive and time consuming. During the past few years a strong increase has been observed in the use of computer simulations due to the fast developments in computer hardware and simulation software. Based on this idea, an effort to develop a computational simulation system to model human dynamic motion for EVA is initiated. This study focuses on the simulation of an astronaut moving the orbital replaceable units into the worksites or removing them from the worksites. Our physics-based methodology helps fill the gap in quantitative analysis of astronaut EVA by providing a multisegment human arm model. Simulation work described in the study improves on the realism of previous efforts, incorporating joint stops to account for the physiological limits of range of motion. To demonstrate the utility of this approach human arm model is simulated virtually using ADAMS/LifeMOD® software. Kinematic mechanism for the astronaut’s task is studied from joint angles and torques. Simulation results obtained is validated with numerical simulation based on the principles of Newton-Euler method. Torques determined using mathematical model are compared among the subjects to know the grace and consistency of the task performed. We conclude that due to uncertain nature of exploration-class EVA, a virtual model developed using multibody dynamics approach offers significant advantages over traditional human modeling approaches.
Abstract: Fault diagnosis of Linear Parameter-Varying (LPV)
system using an adaptive Kalman filter is proposed. The LPV model
is comprised of scheduling parameters, and the emulator parameters.
The scheduling parameters are chosen such that they are capable of
tracking variations in the system model as a result of changes in the
operating regimes. The emulator parameters, on the other hand,
simulate variations in the subsystems during the identification phase
and have negligible effect during the operational phase. The nominal
model and the influence vectors, which are the gradient of the feature
vector respect to the emulator parameters, are identified off-line from
a number of emulator parameter perturbed experiments. A Kalman
filter is designed using the identified nominal model. As the system
varies, the Kalman filter model is adapted using the scheduling
variables. The residual is employed for fault diagnosis. The
proposed scheme is successfully evaluated on simulated system as
well as on a physical process control system.
Abstract: To increase the temperature contrast in thermal
images, the characteristics of the electrical conductivity and thermal
imaging modalities can be combined. In this experimental study, it is
objected to observe whether the temperature contrast created by the
tumor tissue can be improved just due to the current application
within medical safety limits. Various thermal breast phantoms are
developed to simulate the female breast tissue. In vitro experiments
are implemented using a thermal infrared camera in a controlled
manner. Since experiments are implemented in vitro, there is no
metabolic heat generation and blood perfusion. Only the effects and
results of the electrical stimulation are investigated. Experimental
study is implemented with two-dimensional models. Temperature
contrasts due to the tumor tissues are obtained. Cancerous tissue is
determined using the difference and ratio of healthy and tumor
images. 1 cm diameter single tumor tissue causes almost 40 °mC
temperature contrast on the thermal-breast phantom. Electrode
artifacts are reduced by taking the difference and ratio of background
(healthy) and tumor images. Ratio of healthy and tumor images show
that temperature contrast is increased by the current application.
Abstract: The soil profile at site of the bridge project includes soft fine grained soil layer located between 5.0 m to 11.0 m in depth, it has high water content, low SPT no., and low bearing capacity. The clay layer induces high settlement due to surcharge application of earth embankment at ramp T1, ramp T2, and ramp T3 especially at heights from 9m right 3m. Calculated settlement for embankment heights less than 3m may be accepted regarding Saudi Code for soil and foundation. The soil and groundwater at the project site comprise high contents of sulfates and chlorides of high aggressively on concrete and steel bars, respectively. Regarding results of the study, it has been recommended to use stone column piles or new technology named PCC piles as soil improvement to improve the bearing capacity of the weak layer. The new technology is cast in-situ thin wall concrete pipe piles (PCC piles), it has economically advantageous and high workability. The technology can save time of implementation and cost of application is almost 30% of other types of piles.
Abstract: The effectiveness of microchannels in enhancing heat
transfer has been demonstrated in the semiconductor industry. In
order to tap the microscale heat transfer effects into macro
geometries, overcoming the cost and technological constraints,
microscale passages were created in macro geometries machined
using conventional fabrication methods. A cylindrical insert was
placed within a pipe, and geometrical profiles were created on the
outer surface of the insert to enhance heat transfer under steady-state
single-phase liquid flow conditions. However, while heat transfer
coefficient values of above 10 kW/m2·K were achieved, the heat
transfer enhancement was accompanied by undesirable pressure drop
increment. Therefore, this study aims to address the high pressure
drop issue using Constructal theory, a universal design law for both
animate and inanimate systems. Two designs based on Constructal theory were developed to study
the effectiveness of Constructal features in reducing the pressure drop
increment as compared to parallel channels, which are commonly
found in microchannel fabrication. The hydrodynamic and heat
transfer performance for the Tree insert and Constructal fin (Cfin)
insert were studied using experimental methods, and the underlying
mechanisms were substantiated by numerical results. In technical
terms, the objective is to achieve at least comparable increment in
both heat transfer coefficient and pressure drop, if not higher
increment in the former parameter. Results show that the Tree insert improved the heat transfer
performance by more than 16 percent at low flow rates, as compared
to the Tree-parallel insert. However, the heat transfer enhancement
reduced to less than 5 percent at high Reynolds numbers. On the
other hand, the pressure drop increment stayed almost constant at 20
percent. This suggests that the Tree insert has better heat transfer
performance in the low Reynolds number region. More importantly,
the Cfin insert displayed improved heat transfer performance along
with favourable hydrodynamic performance, as compared to Cfinparallel
insert, at all flow rates in this study. At 2 L/min, the
enhancement of heat transfer was more than 30 percent, with 20
percent pressure drop increment, as compared to Cfin-parallel insert.
Furthermore, comparable increment in both heat transfer coefficient
and pressure drop was observed at 8 L/min. In other words, the Cfin
insert successfully achieved the objective of this study. Analysis of the results suggests that bifurcation of flows is
effective in reducing the increment in pressure drop relative to heat
transfer enhancement. Optimising the geometries of the Constructal
fins is therefore the potential future study in achieving a bigger stride
in energy efficiency at much lower costs.
Abstract: Digital technologies offer many opportunities in the
design and implementation of brand communication and advertising.
Augmented reality (AR) is an innovative technology in marketing
communication that focuses on the fact that virtual interaction with a
product ad offers additional value to consumers. AR enables
consumers to obtain (almost) real product experiences by the way of
virtual information even before the purchase of a certain product.
Aim of AR applications in relation with advertising is in-depth
examination of product characteristics to enhance product knowledge
as well as brand knowledge. Interactive design of advertising
provides observers with an intense examination of a specific
advertising message and therefore leads to better brand knowledge.
The elaboration likelihood model and the central route to persuasion
strongly support this argumentation. Nevertheless, AR in brand
communication is still in an initial stage and therefore scientific
findings about the impact of AR on information processing and brand
attitude are rare. The aim of this paper is to empirically investigate
the potential of AR applications in combination with traditional print
advertising. To that effect an experimental design with different
levels of interactivity is built to measure the impact of interactivity of
an ad on different variables o advertising effectiveness.
Abstract: Fe-2%Mn-0.5%Si-0.2C steel was welded and corroded
at 600, 700 and 800oC for 20 h in 1 atm of N2/H2S/H2O-mixed gas in
order to characterize the high-temperature corrosion behavior of the
welded joint. Corrosion proceeded fast and almost linearly. It
increased with an increase in the corrosion temperature. H2S formed
FeS owing to sulfur released from H2S. The scales were fragile and
nonadherent.
Abstract: Interaction between mixing and crystallization is often
ignored despite the fact that it affects almost every aspect of the
operation including nucleation, growth, and maintenance of the
crystal slurry. This is especially pronounced in multiple impeller
systems where flow complexity is increased. By choosing proper
mixing parameters, what closely depends on the knowledge of the
hydrodynamics in a mixing vessel, the process of batch cooling
crystallization may considerably be improved. The values that render
useful information when making this choice are mixing time and
power consumption. The predominant motivation for this work was
to investigate the extent to which radial dual impeller configuration
influences mixing time, power consumption and consequently the
values of metastable zone width and nucleation rate. In this research,
crystallization of borax was conducted in a 15 dm3 baffled batch
cooling crystallizer with an aspect ratio (H/T) of 1.3. Mixing was
performed using two straight blade turbines (4-SBT) mounted on the
same shaft that generated radial fluid flow. Experiments were
conducted at different values of N/NJS ratio (impeller speed/
minimum impeller speed for complete suspension), D/T ratio
(impeller diameter/crystallizer diameter), c/D ratio (lower impeller
off-bottom clearance/impeller diameter), and s/D ratio (spacing
between impellers/impeller diameter). Mother liquor was saturated at
30°C and was cooled at the rate of 6°C/h. Its concentration was
monitored in line by Na-ion selective electrode. From the values of
supersaturation that was monitored continuously over process time, it
was possible to determine the metastable zone width and
subsequently the nucleation rate using the Mersmann’s nucleation
criterion. For all applied dual impeller configurations, the mixing
time was determined by potentiometric method using a pulse
technique, while the power consumption was determined using a
torque meter produced by Himmelstein & Co. Results obtained in
this investigation show that dual impeller configuration significantly
influences the values of mixing time, power consumption as well as
the metastable zone width and nucleation rate. A special attention
should be addressed to the impeller spacing considering the flow
interaction that could be more or less pronounced depending on the
spacing value.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: A university-wide survey to obtain baseline data
regarding the perceptions of key terms related to e-learning and
distance learning among students, faculty and staff was conducted to
help achieve the goals of Princess Nourah bint Abdulrahman
University’s and the Kingdom of Saudi Arabia’s National Center for
e-learning and Distance Learning. This paper comprises a relevant
literature review, the survey methodology, preliminary data analysis,
discussion, and recommendations for further research. The major
findings indicate a deep and wide differentiation of understanding
among users of critical key terms.
Abstract: The cities of Johannesburg and Pretoria both located in the Gauteng province are separated by a distance of 58 km. The traffic queues on the Ben Schoeman freeway which connects these two cities can stretch for almost 1.5 km. Vehicle traffic congestion impacts negatively on the business and the commuter’s quality of life. The goal of this paper is to identify variables that influence the flow of traffic and to design a vehicle traffic prediction model, which will predict the traffic flow pattern in advance. The model will unable motorist to be able to make appropriate travel decisions ahead of time. The data used was collected by Mikro’s Traffic Monitoring (MTM). Multi-Layer perceptron (MLP) was used individually to construct the model and the MLP was also combined with Bagging ensemble method to training the data. The cross—validation method was used for evaluating the models. The results obtained from the techniques were compared using predictive and prediction costs. The cost was computed using combination of the loss matrix and the confusion matrix. The predicted models designed shows that the status of the traffic flow on the freeway can be predicted using the following parameters travel time, average speed, traffic volume and day of month. The implications of this work is that commuters will be able to spend less time travelling on the route and spend time with their families. The logistics industry will save more than twice what they are currently spending.
Abstract: Microstructure and mechanical properties of AZ91D
Mg alloys for nonflammable use, containing Ca and Y, were
investigated in this study. Solid solution treatment of AZ91D Mg alloy
with Ca and Y was successfully conducted at 420oC and
supersaturated microstructure with almost all beta phases resolved into
matrix was obtained. After solid solution treatment, the alloy was
annealed at temperatures of 180 and 200oC for time intervals from 1
min to 48 hrs and hardness of each condition was measured by
micro-Vickers method. Peak aging conditions were deduced from the
results as at the temperature of 200oC for 10 hrs. Hot rolling was also
carried out at 400oC by the reduction ratio of 0.6 through 5 passes
followed by recrystallization treatment. Tensile and compressive
properties were measured at room temperature on the specimens of
each process, i.e. as-cast, solution treatment, hot rolling, and
recrystallization.
Abstract: In this study, total fatty acid composition of muscle
lipids of Cyprinus carpio L. living in Suğla Dam Lake, Altinapa Dam
Lake, Eğirdir Lake and Burdur Lake were determined using GC.
During this study, for the summer season of July was taken from each
region of the land and they were stored in deep-freeze set to -20
degrees until the analysis date. At the end of the analyses, 30
different fatty acids were found in the composition of Cyprinus
carpio L. which lives in different lakes. Cyprinus carpio Suğla Dam
Lake of polyunsaturated fatty acids (PUFAs), were higher than other
lakes. Cyprinus carpio L. was the highest in the major SFA palmitic
acid. Polyunsaturated fatty acids (PUFA) of carp, the most abundant
fish species in all lakes, were found to be higher than those of
saturated fatty acids (SFA) in all lakes. Palmitic acid was the major
SFA in all lakes. Oleic acid was identified as the major MUFA.
Docosahexaenoic acid (DHA) was the most abundant in all lakes. ω3
fatty acid composition was higher than the percentage of the
percentage ω6 fatty acids in all lake. ω3/ω6 rates of Cyprinus carpio
L. Suğla Dam Lake, Altinapa Dam Lake, Eğirdir Lake and Burdur
Lake, 2.12, 1.19, 2.15, 2.87, and 2.82, respectively. Docosahexaenoic
acid (DHA) was the major PUFA in Eğirdir and Burdur lakes,
whereas linoleic acid (LA) was the major PUFA in Altinapa and
Suğla Dam Lakes. It was shown that the fatty acid composition in the
muscle of carp was significantly influenced by different lakes.
Abstract: Although Mobile Wireless Sensor Networks (MWSNs),
which consist of mobile sensor nodes (MSNs), can cover a wide range
of observation region by using a small number of sensor nodes, they
need to construct a network to collect the sensing data on the base
station by moving the MSNs. As an effective method, the network
construction method based on Virtual Rails (VRs), which is referred
to as VR method, has been proposed. In this paper, we propose two
types of effective techniques for the VR method. They can prolong
the operation time of the network, which is limited by the battery
capabilities of MSNs and the energy consumption of MSNs. The
first technique, an effective arrangement of VRs, almost equalizes
the number of MSNs belonging to each VR. The second technique,
an adaptive movement method of MSNs, takes into account the
residual energy of battery. In the simulation, we demonstrate that each
technique can improve the network lifetime and the combination of
both techniques is the most effective.
Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.
Abstract: In language learning, second language learners as well
as Native speakers commit errors in their attempt to achieve
competence in the target language. The realm of collocation has to do
with meaning relation between lexical items. In all human language,
there is a kind of ‘natural order’ in which words are arranged or relate
to one another in sentences so much so that when a word occurs in a
given context, the related or naturally co-occurring word will
automatically come to the mind. It becomes an error, therefore, if
students inappropriately pair or arrange such ‘naturally’ co–occurring
lexical items in a text. It has been observed that most of the second
language learners in this research group commit collocation errors. A
study of this kind is very significant as it gives insight into the kinds
of errors committed by learners. This will help the language teacher
to be able to identify the sources and causes of such errors as well as
correct them thereby guiding, helping and leading the learners
towards achieving some level of competence in the language. The
aim of the study is to understand the nature of these errors as
stumbling blocks to effective essay writing. The objective of the
study is to identify the errors, analyze their structural compositions so
as to determine whether there are similarities between students in this
regard and to find out whether there are patterns to these kinds of
errors which will enable the researcher to understand their sources
and causes. As a descriptive research, the researcher samples some
nine hundred essays collected from three hundred undergraduate
learners of English as a second language in the Federal College of
Education, Kano, North- West Nigeria, i.e. three essays per each
student. The essays which were given on three different lecture times
were of similar thematic preoccupations (i.e. same topics) and length
(i.e. same number of words). The essays were written during the
lecture hour at three different lecture occasions. The errors were
identified in a systematic manner whereby errors so identified were
recorded only once even if they occur severally in students’ essays.
The data was collated using percentages in which the identified
numbers of occurrences were converted accordingly in percentages.
The findings from the study indicate that there are similarities as well
as regular and repeated errors which provided a pattern. Based on the
pattern identified, the conclusion is that students’ collocation errors
are attributable to poor teaching and learning which resulted in wrong
generalization of rules.
Abstract: In order to study the Mutual effect of genotype ×
environment for the percent of oil index in sunflower items, an
experiment was accomplished form complete random block designs
in four iteration and was four diverse researching station comprising
Esfahan, Birjand, Sari, and Karaj. Complex variance analysis showed
that there is an important diversity between the items under
investigation. The results relevant the coefficient variation of items
Azargol and Vidoc has respectively allocated the minimum
coefficient of variations. According to the results extrapolated from
Shokla stability variance, the Items Brocar, Allison and Fabiola, are
among the stable genotypes for oil percent respectively. In the biplot
GGE, the location under investigations divided in two superenvironments,
first one comprised of locations naming Esfahan,
Karaj, and Birjand, and second one were such a location as Sari. By
this point of view, in the first super-environment, the Item Fabiola
and in the second Almanzor item was among the best items and
crops.
Abstract: Fermentation is well known as an essential process to
develop chocolate flavor in dried cocoa beans. Besides developing
the precursor of cocoa flavor, it also induces the color changes in the
beans. The fermentation process is influenced by various factors such
as planting material, preconditioning of cocoa pod and fermentation
technique. Therefore, this study was conducted to evaluate color of
Malaysian cocoa beans and how the duration of pods storage and
fermentation technique using shallow box will effect on its color
characteristics. There are two factors being studied i.e. duration of
cocoa pod storage (0, 2, 4 and 6 days) and duration of cocoa
fermentation (0, 1, 2, 3, 4 and 5 days). The experiment is arranged in
4 x 6 factorial designs with 24 treatments and arrangement is in a
Completely Randomised Design (CRD). The produced beans are
inspected for color changes under artificial light during cut test and
divided into four groups of color namely fully brown, purple brown,
fully purple and slaty. Cut tests indicated that cocoa beans which are
directly dried without undergone fermentation has the highest slaty
percentage. However, application of pods storage before fermentation
process is found to decrease the slaty percentage. In contrast, the
percentages of fully brown beans start to dominate after two days of
fermentation, especially from four and six days of pods storage batch.
Whereas, almost all batches of cocoa beans have a percentage of fully
purple less than 20%. Interestingly, the percentage of purple brown
beans are scattered in the entire beans batch regardless any specific
trend. Meanwhile, statistical analysis using General Linear Model
showed that the pods storage has a significant effect on the color
characteristic of the Malaysian dried beans compared to fermentation
duration.
Abstract: Dietary cholesterol has elicited the most public
interest as it relates with coronary heart disease. Thus, humans have
been paying more attention to health, thereby reducing consumption
of cholesterol enriched food. Egg is considered as one of the major
sources of human dietary cholesterol. However, an alternative way to
reduce the potential cholesterolemic effect of eggs is to modify the
fatty acid composition of the yolk. The effect of palm oil (PO),
soybean oil (SO), sesame seed oil (SSO) and fish oil (FO)
supplementation in the diets of layers on egg yolk fatty acid,
cholesterol, egg production and egg quality parameters were
evaluated in a 42-day feeding trial. One hundred and five Isa Brown
laying hens of 34 weeks of age were randomly distributed into seven
groups of five replicates and three birds per replicate in a completely
randomized design. Seven corn-soybean basal diets (BD) were
formulated: BD+No oil (T1), BD+1.5% PO (T2), BD+1.5% SO (T3),
BD+1.5% SSO (T4), BD+1.5% FO (T5), BD+0.75% SO+0.75% FO
(T6) and BD+0.75% SSO+0.75% FO (T7). Five eggs were randomly
sampled at day 42 from each replicate to assay for the cholesterol,
fatty acid profile of egg yolk and egg quality assessment. Results
showed that there were no significant (P>0.05) differences observed
in production performance, egg cholesterol and egg quality
parameters except for yolk height, albumen height, yolk index, egg
shape index, haugh unit, and yolk colour. There were no significant
differences (P>0.05) observed in total cholesterol, high density
lipoprotein and low density lipoprotein levels of egg yolk across the
treatments. However, diets had effect (P