Abstract: Biomass briquette gasification is regarded as a
promising route for efficient briquette use in energy generation, fuels
and other useful chemicals. However, previous research has been
focused on briquette gasification in fixed bed gasifiers such as
updraft and downdraft gasifiers. Fluidised bed gasifier has the
potential to be effectively sized to medium or large scale. This study
investigated the use of fuel briquettes produced from blends of rice
husks and corn cobs biomass, in a bubbling fluidised bed gasifier.
The study adopted a combination of numerical equations and Aspen
Plus simulation software, to predict the product gas (syngas)
composition base on briquette density and biomass composition
(blend ratio of rice husks to corn cobs). The Aspen Plus model was
based on an experimentally validated model from the literature. The
results based on a briquette size 32 mm diameter and relaxed density
range of 500 to 650kg/m3, indicated that fluidisation air required in
the gasifier increased with increase in briquette density, and the
fluidisation air showed to be the controlling factor compared with the
actual air required for gasification of the biomass briquettes. The
mass flowrate of CO2 in the predicted syngas composition increased
with an increase in air flow, in the gasifier, while CO decreased and
H2 was almost constant. The ratio of H2 to CO for various blends of
rice husks and corn cobs did not significantly change at the designed
process air, but a significant difference of 1.0 was observed between
10/90 and 90/10 % blend of rice husks and corn cobs.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Optimal feeding, including optimal micronutrient
intake, becomes one of the ways to overcome the long-term
consequences of undernutrition. Macronutrient and micronutrient
intake were important to a rapid growth and development of young
children. The study objective was to assess macro and micronutrient
intake and its adequacy in children aged 12-23 months. This survey
was a cross-sectional study, involving 83 caregivers with children
aged 12-23 months old in Senen Sub-district, Central Jakarta selected
through simple random sampling. Data on nutrient intake was
obtained through interview using single 24-hour recall. Repeated 24-
hour recall to sub-sample was done to estimate the proportion of
nutrient inadequacy. The highest prevalence of nutrient inadequacy
was iron (52.4%), followed by vitamin C (30.9%) and zinc (28.8%).
Almost 12% children had inadequate energy intake. More than half
of children (62.6%) were anemic (25.3% were severely anemic).
Micronutrient inadequacy, especially iron, was more problematic
than macronutrient inadequacy in the study area.
Abstract: Computational fluid dynamics analysis of the burning
of syngas fuels derived from biomass and plastic solid waste mixture
through gasification process is presented in this paper. The syngas
fuel is burned in gas turbine can combustor. Gas turbine can
combustor with swirl is designed to burn the fuel efficiently and
reduce the emissions. The main objective is to test the impact of the
alternative syngas fuel compositions and lower heating value on the
combustion performance and emissions. The syngas fuel is produced
by blending palm kernel shell (PKS) with polyethylene (PE) waste
via catalytic steam gasification (fluidized bed reactor). High
hydrogen content syngas fuel was obtained by mixing 30% PE waste
with PKS. The syngas composition obtained through the gasification
process is 76.2% H2, 8.53% CO, 4.39% CO2 and 10.90% CH4. The
lower heating value of the syngas fuel is LHV = 15.98 MJ/m3. Three
fuels were tested in this study natural gas (100%CH4), syngas fuel
and pure hydrogen (100% H2). The power from the combustor was
kept constant for all the fuels tested in this study. The effect of syngas
fuel composition and lower heating value on the flame shape, gas
temperature, mass of carbon dioxide (CO2) and nitrogen oxides
(NOX) per unit of energy generation is presented in this paper. The
results show an increase of the peak flame temperature and NO mass
fractions for the syngas and hydrogen fuels compared to natural gas
fuel combustion. Lower average CO2 emissions at the exit of the
combustor are obtained for the syngas compared to the natural gas
fuel.
Abstract: Five palm oil ether monoesters utilized as novel
biodiesels were synthesized and structurally identified in the paper.
The investigation was made on the effect of ether species on
physicochemical properties of the palm oil ether monoesters. The
results showed that density, kinematic viscosity, smoke point, and
solidifying point increase linearly with their –CH2 group number in
certain relationships. Cetane number is enhanced whereas heat value
decreases linearly with –CH2 group number. In addition, the
influencing regularities of the volumetric content of the palm oil ether
monoesters on the fuel properties were also studied when the ether
monoesters are used as diesel fuel additives.
Abstract: The rationale behind this study is considering
combating and preventing the phenomenon of trafficking in human
beings from a multidisciplinary perspective that involves many layers
of the society.
Trafficking in human beings is an abhorrent phenomenon highly
affecting negatively the victims and their families in both human and
material aspect, sometimes causing irreversible damages. The longer
term effects of this phenomenon, in countries with a weak economic
development and extremely young and dynamic population, such as
Kosovo, without proper measures to prevented and control can cause
tremendous damages in the society. Given the fact that a complete
eradication of this phenomenon is almost impossible, efforts should
be concentrated at least on the prevention and controlling aspects.
Treating trafficking in human beings based on traditional police
tactics, methods and proceedings cannot bring satisfactory results.
There is no doubt that a multi-disciplinary approach is an
irreplaceable requirement, in other words, a combination of authentic
and functional proactive and reactive methods, techniques and tactics.
Obviously, police must exercise its role in preventing and combating
trafficking in human beings, a role sanctioned by the law, however,
police role and contribution cannot by any means considered
complete if all segments of the society are not included in these
efforts. Naturally, civil society should have an important share in
these collaborative and interactive efforts especially in preventive
activities such as: awareness on trafficking risks and damages,
proactive engagement in drafting appropriate legislation and
strategies, law enforcement monitoring and direct or indirect
involvement in protective and supporting activities which benefit the
victims of trafficking etc.
Abstract: The aim of this study is to investigate formability of
Al based closed cell metallic foams at high temperature. The foam
specimens with rectangular section were produced from
AlMg1Si0.6TiH20.8 alloy preform material. Bending and free
bending tests based on gravity effect were applied to foam specimens
at high temperatures. During the tests, the time-angular deformation
relationships with various temperatures were determined.
Deformation types formed in cell walls were investigated by means
of Scanning Electron Microscopy (SEM) and optical microscopy.
Bending deformation about 90° was achieved without any defect at
high temperatures. The importance of a critical temperature and
deformation rate was emphasized in maintaining the deformation.
Significant slip lines on surface of cell walls at tensile zones of
bending specimen were observed. At high strain rates, the microcrack
formation in boundaries of elongated grains was determined.
Abstract: Experimental studies to investigate the depth of the
scour conducted at a side-weir intersection located at the 1800 curved
flume which located Hydraulic Laboratory of Yıldız Technical
University, Istanbul, Turkey. Side weirs were located at the middle of
the straight part of the main channel. Three different lengths (25, 40
and 50 cm) and three different weir crest height (7, 10 and 12 cm) of
the side weir placed on the side weir station. There is no scour when
the material is only kaolin. Therefore, the cohesive bed was prepared
by properly mixing clay material (kaolin) with 31% sand in all
experiments. Following 24h consolidation time, in order to observe
the effect of flow intensity on the scour depth, experiments were
carried out for five different upstream Froude numbers in the range of
0.33-0.81.
As a result of this study the relation between scour depth and
upstream flow intensity as a function of time have been established.
The longitudinal velocities decreased along the side weir; towards the
downstream due to overflow over the side-weirs. At the beginning,
the scour depth increases rapidly with time and then asymptotically
approached constant values in all experiments for all side weir
dimensions as in non-cohesive sediment. Thus, the scour depth
reached equilibrium conditions. Time to equilibrium depends on the
approach flow intensity and the dimensions of side weirs. For
different heights of the weir crest, dimensionless scour depths
increased with increasing upstream Froude number. Equilibrium
scour depths which formed 7 cm side-weir crest height were obtained
higher than that of the 12 cm side-weir crest height. This means when
side-weir crest height increased equilibrium scour depths decreased.
Although the upstream side of the scour hole is almost vertical, the
downstream side of the hole is inclined.
Abstract: Medicinal plants are now gaining attractiveness in
treatment of bacterial infections and food preservation. The objective
of this study was to assess antibacterial activity of some medicinal
plants on pathogenic bacteria. Screening of antibacterial activity of
aqueous and methanol extracts of some plants: Jojoba, Ginger, Sage,
Thyme and Clove against Bacillus cereus, Salmonella typhimurium,
Staphylococcus aureus, Clostridium perfringens and Escherichia coli
were investigated. Antibacterial activity was performed by agar
diffusion and disc diffusion method. Jatropha, Jojoba, Clove and
Ginger extracts showed notable bacterial activity in the first
screening step then selected to be tested against Bacillus cereus
(Gram+), Staphylococcus aureus (Gram+) and Salmonella
typhimurium (Gram−) and their effect was compared using
antibiotics as control. Screening results showed potential antibacterial
activity of the tested plant extracts against the screened bacterial
strains. It was found that methanol extracts exhibited higher
antibacterial activity than aqueous extracts. Methanol extract of
Jatropha showed the highest inhibition zone against Staphylococcus
aureus (Gram+) with 24.00 mm diameter, compared to the other
plant extracts followed by clove. Meanwhile, the inhibition zones of
methanol extracts of Jojoba and Ginger were the same (12mm).The
Gram-positive bacteria were found to be more sensitive to aqueous
and methanol extracts than Gram-negative bacteria.
Abstract: A field study was conducted to evaluate the efficacy of
safflower plant for phytoremediation of contaminated soils. The
experiment was performed on an agricultural fields contaminated by
the Non-Ferrous-Metal Works near Plovdiv, Bulgaria. Field
experiments with randomized complete block design with five
treatments (control, compost amendments added at 20 and 40 t/daa,
and vermicompost amendments added at 20 and 40 t/daa) were
carried out. The quality of safflower seeds and oil (heavy metals and
fatty acid composition) were determined. Tested organic amendments
significantly influenced the chemical composition of safflower seeds
and oil. The compost and vermicompost treatments significantly
reduced heavy metals concentration in safflower seeds and oils, but
the effect differed among them. Addition of vermicompost and
compost leads to an increase in the content of palmitic acid and
linoleic acid, and a decrease in the stearic and oleic acids compared
with the control. A significant increase in the quantity of saturated
acids was observed in the variants with 20 t/daa of compost and 20
t/daa of vermicompost (9.1 and 8.9% relative to the control).
Safflower is a plant which is tolerant to heavy metals and can be
successfully used in the phytoremediation of heavy metal
contaminated soils. The processing of seeds to oil and using the
obtained oil for nutritional purposes will greatly reduce the cost of
phytoremediation.
Abstract: Margin-Based Principle has been proposed for a long
time, it has been proved that this principle could reduce the
structural risk and improve the performance in both theoretical
and practical aspects. Meanwhile, feed-forward neural network is
a traditional classifier, which is very hot at present with a deeper
architecture. However, the training algorithm of feed-forward neural
network is developed and generated from Widrow-Hoff Principle that
means to minimize the squared error. In this paper, we propose
a new training algorithm for feed-forward neural networks based
on Margin-Based Principle, which could effectively promote the
accuracy and generalization ability of neural network classifiers
with less labelled samples and flexible network. We have conducted
experiments on four UCI open datasets and achieved good results
as expected. In conclusion, our model could handle more sparse
labelled and more high-dimension dataset in a high accuracy while
modification from old ANN method to our method is easy and almost
free of work.
Abstract: The aim of this exploratory research is to understand
further how organisations can evaluate their activities, which
generate knowledge creation, to meet changing stakeholder
expectations. A Scale of Knowledge (SoK) Framework is proposed
which links knowledge management and organisational activities to
changing stakeholder expectations. The framework was informed by
the knowledge management literature, as well as empirical work
conducted via a single case study of a multi-site hospital organisation
in Saudi Arabia. Eight in-depth semi-structured interviews were
conducted with managers from across the organisation regarding
current and future stakeholder expectations, organisational
strategy/activities and knowledge management. Data were analysed
using thematic analysis and a hierarchical value map technique to
identify activities that can produce further knowledge and
consequently impact on how stakeholder expectations are met.
The SoK Framework developed may be useful to practitioners as
an analytical aid to determine if current organisational activities
produce organisational knowledge which helps them meet
(increasingly higher levels of) stakeholder expectations. The
limitations of the research and avenues for future development of the
proposed framework are discussed.
Abstract: In order to produce lead free piezoceramics with
optimum piezoelectric and dielectric properties, KNN modified with
Li+ (as an A site dopant) and Sb5+ (as a B site dopant)
(K0.49Na0.49Li0.02) (Nb0.96Sb0.04) O3 (referred as KNLNS in this paper)
have been synthesized using solid state reaction method and
conventional sintering technique. The ceramics were sintered in the
narrow range of 1050°C-1090°C for 2-3 h to get precise information
about sintering parameters. Detailed study of dependence of
microstructural, dielectric and piezoelectric properties on sintering
conditions was then carried out. The study suggests that the volatility
of the highly hygroscopic KNN ceramics is not only sensitive to
sintering temperatures but also to sintering durations. By merely
reducing the sintering duration for a given sintering temperature we
saw an increase in the density of the samples which was supported by
the increase in dielectric constants of the ceramics. And since density
directly or indirectly affects almost all the associated properties, other
dielectric and piezoelectric properties were also enhanced as we
approached towards the most suitable sintering temperature and
duration combination. The detailed results are reported in this paper.
Abstract: The use of engineered nanomaterials has increased as
a result of their positive impact on many sectors of the economy,
including agriculture. Silver nanoparticles (AgNPs) are now used to
enhance seed germination, plant growth, and photosynthetic quantum
efficiency and as antimicrobial agents to control plant diseases. In
this study, we examined the effect of AgNP dosage on the seed
germination of three plant species: corn (Zea mays L.), watermelon
(Citrullus lanatus [Thunb.] Matsum. & Nakai) and zucchini
(Cucurbita pepo L.). This experiment was designed to study the
effect of AgNPs on germination percentage, germination rate, mean
germination time, root length and fresh and dry weight of seedlings
for the three species. Seven concentrations (0.05, 0.1, 0.5, 1, 1.5, 2
and 2.5 mg/ml) of AgNPs were examined at the seed germination
stage. The three species had different dose responses to AgNPs in
terms of germination parameters and the measured growth
characteristics. The germination rates of the three plants were
enhanced in response to AgNPs. Significant enhancement of the
germination percentage values was observed after treatment of the
watermelon and zucchini plants with AgNPs in comparison with
untreated seeds. AgNPs showed a toxic effect on corn root
elongation, whereas watermelon and zucchini seedling growth were
positively affected by certain concentrations of AgNPs. This study
showed that exposure to AgNPs caused both positive and negative
effects on plant growth and germination.
Abstract: Heat transfer of leaves is a crucial factor in optimal
operation of metabolic functions in plants. In order to quantify this
phenomenon in different leaves and investigate the influence of leaf
shape on heat transfer, natural convection for pine, orange and olive
leaves was simulated as representatives of different groups of leaf
shapes. CFD techniques were used in this simulation with the
purpose to calculate heat transfer of leaves in similar environmental
conditions. The problem was simulated for steady state and threedimensional
conditions. From obtained results, it was concluded that
heat fluxes of all three different leaves are almost identical, however,
total rate of heat transfer have highest and lowest values for orange
leaves, and pine leaves, respectively.
Abstract: In this research numerical simulations are performed,
using the multi-relaxation-time lattice Boltzmann method, in the
range 3 ≤ β = w[d] ≤ 30 at Re = 100, 200 and 300, where β the
blockage ratio, w is the equispaced distance between centers of
cylinders, d is the diameter of the cylinder and Re is the Reynolds
number, respectively. Special attention is paid to the effect of the
equispaced distance between centers of cylinders. Visualization of
the vorticity contour visualization are presented for some simulation
showing the flow dynamics and patterns for blockage effect. Results
show that the drag and mean drag coefficients, and Strouhal number,
in general, decrease with the increase of β for fixed Re. It is found
that the decreasing rate of drag and mean drag coefficients and
Strouhal number is more distinct in the range 3 ≤ β ≤ 15. We found
that when β > 15, the blockage effect almost diminishes. Our results
further indicate that the drag and mean drag coefficients, peak value
of the lift coefficient, root-mean-square value of the lift and drag
coefficients and the ratio between lift and drag coefficients decrease
with the increase of Re. The results indicate that symmetry boundary
condition have more blockage effect as compared to periodic
boundary condition.
Abstract: An experimental and analytical research on shear
buckling of a comparably large polymer composite I-section is
presented. It is known that shear buckling load of a large span
composite beam is difficult to determine experimentally. In order to
sensitively detect shear buckling of the tested I-section, twenty strain
rosettes and eight displacement sensors were applied and attached on
the web and flange surfaces. The tested specimen was a pultruded
composite beam made of vinylester resin, E-glass, carbon fibers and
micro-fillers. Various coupon tests were performed before the shear
buckling test to obtain fundamental material properties of the Isection.
An asymmetric four-point bending loading scheme was
utilized for the shear test. The loading scheme resulted in a high shear
and almost zero moment condition at the center of the web panel. The
shear buckling load was successfully determined after analyzing the
obtained test data from strain rosettes and displacement sensors. An
analytical approach was also performed to verify the experimental
results and to support the discussed experimental program.
Abstract: Moringa oleifera is a nutritious vegetable tree with
varieties of potential uses, as almost every part of the Moringa
oleifera tree can be used for food. This study was conducted in Oyo
State, Nigeria, to find out the level of acceptability of Moringa
oleifera diversified products among rural and urban dwellers.
Purposive sampling was used to select two local governments’ areas.
Stratified sampling technique was also used to select one community
each from rural and urban areas while snowball sampling technique
was used to select ten respondents each from the two communities,
making a total number of forty respondents. Data were analyzed
using frequencies, percentages, Chi-square, Pearson Product Moment
Correlation and regression analysis. Result from the study revealed
that majority of the respondents (80%) fell within the age range of
20-49 years and 55% of them were male, 55% were married, 70% of
them were Christians, 80% of them had tertiary education. The result
also showed that 85% were aware of the Moringa plant and (65%) of
them have consumed Moringa oleifera and the perception statements
on the benefits of Moringa oleifera indicated that (52.5%) of the
respondents rated Moringa oleifera to be favorable, most of them had
high acceptability for Moringa egusi soup, Moringa tea, Moringa pap
and yam pottage with Moringa. The result of the hypotheses testing
showed that there is a significant relationship between sex of the
respondents and acceptability of the diversified Moringa oleifera
products (x2=6.465, p = 0.011). There is also a significant
relationship between family size of the respondents level of
acceptability of the Moringa oleifera products (r = 0.327, p = 0.040).
Based on the level of acceptability of Moringa oleifera diversified
products; the plant is of great economic importance to the populace.
Therefore, there should be more public awareness through the media
to enlighten people on the beneficial effects of Moringa oleifera.
Abstract: Availability of different genetic tests after completion
of Human Genome Project increases the physicians’ responsibility to
keep themselves update on the potential implementation of these
genetic tests in their daily practice. However, due to numbers of
barriers, still many of physicians are not either aware of these tests or
are not willing to offer or refer their patients for genetic tests. This
study was conducted an anonymous, cross-sectional, mailed-based
survey to develop a primary data of Malaysian physicians’ level of
knowledge and perception of gene profiling. Questionnaire had 29
questions. Total scores on selected questions were used to assess the
level of knowledge. The highest possible score was 11. Descriptive
statistics, one way ANOVA and chi-squared test was used for
statistical analysis. Sixty three completed questionnaires were
returned by 27 general practitioners (GPs) and 36 medical specialists.
Responders’ age ranges from 24 to 55 years old (mean 30.2 ± 6.4).
About 40% of the participants rated themselves as having poor level
of knowledge in genetics in general whilst 60% believed that they
have fair level of knowledge; however, almost half (46%) of the
respondents felt that they were not knowledgeable about available
genetic tests. A majority (94%) of the responders were not aware of
any lab or company which is offering gene profiling services in
Malaysia. Only 4% of participants were aware of using gene profiling
for detection of dosage of some drugs. Respondents perceived greater
utility of gene profiling for breast cancer (38%) compared to the
colorectal familial cancer (3%). The score of knowledge ranged from
2 to 8 (mean 4.38 ± 1.67). Non- significant differences between score
of knowledge of GPs and specialists were observed, with score of
4.19 and 4.58 respectively. There was no significant association
between any demographic factors and level of knowledge. However,
those who graduated between years 2001 to 2005 had higher level of
knowledge. Overall, 83% of participants showed relatively high level
of perception on value of gene profiling to detect patient’s risk of
disease. However, low perception was observed for both statements
of using gene profiling for general population in order to alter their
lifestyle (25%) as well as having the full sequence of a patient
genome for the purpose of determining a patient’s best match for
treatment (18%). The lack of clinical guidelines, limited provider
knowledge and awareness, lack of time and resources to educate
patients, lack of evidence-based clinical information and cost of tests
were the most barriers of ordering gene profiling mentioned by
physicians. In conclusion Malaysian physicians who participate in
this study had mediocre level of knowledge and awareness in gene
profiling. The low exposure to the genetic questions and problems
might be a key predictor of lack of awareness and knowledge on
available genetic tests. Educational and training workshop might be useful in helping Malaysian physicians incorporate genetic profiling
into practice for eligible patients.