Abstract: Cs-type nanocomposite zeolite membrane was successfully synthesized on an alumina ceramic hollow fibre with a mean outer diameter of 1.7 mm; cesium cationic exchange test was carried out inside test module with mean wall thickness of 230 μm and an average crossing pore size smaller than 0.2 μm. Separation factor of n-butane/H2 obtained indicate that a relatively high quality closed to 20. Maxwell-Stefan modeling provides an equivalent thickness lower than 1 µm. To compare the difference an application to CO2/N2 separation has been achieved, reaching separation factors close to (4,18) before and after cation exchange on H-zeolite membrane formed within the pores of a ceramic alumina substrate.
Abstract: The study of effect of laser scanning speed on
material efficiency in Ti6Al4V application is very important because unspent powder is not reusable because of high temperature oxygen
pick-up and contamination. This study carried out an extensive study
on the effect of scanning speed on material efficiency by varying the
speed between 0.01 to 0.1m/sec. The samples are wire brushed and
cleaned with acetone after each deposition to remove un-melted
particles from the surface of the deposit. The substrate is weighed before and after deposition. A formula was developed to calculate the
material efficiency and the scanning speed was compared with the
powder efficiency obtained. The results are presented and discussed.
The study revealed that the optimum scanning speed exists for this study at 0.01m/sec, above and below which the powder efficiency
will drop
Abstract: Characterization and evaluation of the activity of Vespa basalis DPP-IV, which expressed in Spodoptera frugiperda 21 cells. The expression of rDPP-IV was confirmed by SDS–PAGE, Western blot analyses, LC-MS/MS and measurement of its peptidase specificity. One-step purification by Ni-NTA affinity chromatography and the total amount of rDPP-IV recovered was approximately 6.4mg per liter from infected culture medium; an equivalent amount would be produced by 1x109 infected Sf21 insect cells. Through the affinity purification led to highly stable rDPP-IV enzyme was recovered and with significant peptidase activity. The rDPP-IV exhibited classical Michaelis–Menten kinetics, with kcat/Km in the range of 10-500 mM-1×S-1 for the five synthetic substrates and optimum substrate is Ala-Pro-pNA. As expected in inhibition assay, the enzymatic activity of rDPP-IV was significantly reduced by 80 or 60% in the presence of sitagliptin (a DPP-IV inhibitor) or PMSF (a serine protease inhibitor), but was not apparently affected by iodoacetamide (a cysteine protease inhibitor).
Abstract: Stochastic models of biological networks are well established in systems biology, where the computational treatment of such models is often focused on the solution of the so-called chemical master equation via stochastic simulation algorithms. In contrast to this, the development of storage-efficient model representations that are directly suitable for computer implementation has received significantly less attention. Instead, a model is usually described in terms of a stochastic process or a "higher-level paradigm" with graphical representation such as e.g. a stochastic Petri net. A serious problem then arises due to the exponential growth of the model-s state space which is in fact a main reason for the popularity of stochastic simulation since simulation suffers less from the state space explosion than non-simulative numerical solution techniques. In this paper we present transition class models for the representation of biological network models, a compact mathematical formalism that circumvents state space explosion. Transition class models can also serve as an interface between different higher level modeling paradigms, stochastic processes and the implementation coded in a programming language. Besides, the compact model representation provides the opportunity to apply non-simulative solution techniques thereby preserving the possible use of stochastic simulation. Illustrative examples of transition class representations are given for an enzyme-catalyzed substrate conversion and a part of the bacteriophage λ lysis/lysogeny pathway.
Abstract: Anaerobic Digestion has become a promising
technology for biological transformation of organic fraction of the
municipal solid wastes (MSW). In order to represent the kinetic
behavior of such biological process and thereby to design a reactor
system, development of a mathematical model is essential.
Addressing this issue, a simplistic mathematical model has been
developed for anaerobic digestion of MSW in a continuous flow
reactor unit under homogeneous steady state condition. Upon
simulated hydrolysis, the kinetics of biomass growth and substrate
utilization rate are assumed to follow first order reaction kinetics.
Simulation of this model has been conducted by studying sensitivity
of various process variables. The model was simulated using typical
kinetic data of anaerobic digestion MSW and typical MSW
characteristics of Kolkata. The hydraulic retention time (HRT) and
solid retention time (SRT) time were mainly estimated by varying
different model parameters like efficiency of reactor, influent
substrate concentration and biomass concentration. Consequently,
design table and charts have also been prepared for ready use in the
actual plant operation.
Abstract: This study aims to demonstrate the quantification of
peptides based on isotope dilution surface enhanced Raman
scattering (IDSERS). SERS spectra of phenylalanine (Phe), leucine
(Leu) and two peptide sequences TGQIFK (T13) and
YSFLQNPQTSLCFSESIPTPSNR (T6) as part of the 22-kDa
human growth hormone (hGH) were obtained on Ag-nanoparticle
covered substrates. On the basis of the dominant Phe and Leu
vibrational modes, precise partial least squares (PLS) prediction
models were built enabling the determination of unknown T13 and
T6 concentrations. Detection of hGH in its physiological
concentration in order to investigate the possibility of protein
quantification has been achieved.
Abstract: This paper presents the results of the preliminary investigation of microwave (MW) irradiation pretreatments on the anaerobic digestion of food residues using biochemical methane potential (BMP) assays. Low solids systems with a total solids (TS) content ranging from 5.0-10.0% were analyzed. The inoculum to bulk mass of substrates to water ratio was 1:2:2 (mass basis). The experimental conditions for pretreatments were as follows: a control (no MW irradiation), two runs with MW irradiation for 15 and 30 minutes at 320 W, and another two runs with MW irradiation at 528 W for 30 and 60 minutes. The cumulative biogas production were 6.3 L and 8.7 L for 15min/320 W and 30min/320 W MW irradiation conditions, respectively, and 10.5 L and 11.4 L biogas for 30min/528 W and 60min/528 W, respectively, as compared to the control giving 5.8 L biogas. Both an increase in exposure time of irradiation and power of MW had increased the rate and yield of biogas. Singlefactor ANOVA tests (p
Abstract: An ultrasound-assisted activation method for
electroless silver plating is presented in this study. When the
ultrasound was applied during the activation step, the amount of the Pd
species adsorbed on substrate surfaces was higher than that of sample
pretreated with a conventional activation process without ultrasound
irradiation. With this activation method, it was also shown that the
adsorbed Pd species with a size of about 5 nm were uniformly
distributed on the surfaces, thus a smooth and uniform coating on the
surfaces was obtained by subsequent electroless silver plating. The
samples after each step were characterized by AFM, XPS, FIB, and
SEM.
Abstract: Biochemical Oxygen Demand (BOD) is a measure of
the oxygen used in bacteria mediated oxidation of organic substances
in water and wastewater. Theoretically an infinite time is required for
complete biochemical oxidation of organic matter, but the
measurement is made over 5-days at 20 0C or 3-days at 27 0C test
period with or without dilution. Researchers have worked to further
reduce the time of measurement.
The objective of this paper is to review advancement made in
BOD measurement primarily to minimize the time and negate the
measurement difficulties. Survey of literature review in four such
techniques namely BOD-BARTTM, Biosensors, Ferricyanidemediated
approach, luminous bacterial immobilized chip method.
Basic principle, method of determination, data validation and their
advantage and disadvantages have been incorporated of each of the
methods.
In the BOD-BARTTM method the time lag is calculated for the
system to change from oxidative to reductive state. BIOSENSORS
are the biological sensing element with a transducer which produces
a signal proportional to the analyte concentration. Microbial species
has its metabolic deficiencies. Co-immobilization of bacteria using
sol-gel biosensor increases the range of substrate. In ferricyanidemediated
approach, ferricyanide has been used as e-acceptor instead
of oxygen. In Luminous bacterial cells-immobilized chip method,
bacterial bioluminescence which is caused by lux genes was
observed. Physiological responses is measured and correlated to
BOD due to reduction or emission.
There is a scope to further probe into the rapid estimation of BOD.
Abstract: In this paper, periodic force operation of a wastewater treatment process has been studied for the improved process performance. A previously developed dynamic model for the process is used to conduct the performance analysis. The static version of the model was utilized first to determine the optimal productivity conditions for the process. Then, feed flow rate in terms of dilution rate i.e. (D) is transformed into sinusoidal function. Nonlinear model predictive control algorithm is utilized to regulate the amplitude and period of the sinusoidal function. The parameters of the feed cyclic functions are determined which resulted in improved productivity than the optimal productivity under steady state conditions. The improvement in productivity is found to be marginal and is satisfactory in substrate conversion compared to that of the optimal condition and to the steady state condition, which corresponds to the average value of the periodic function. Successful results were also obtained in the presence of modeling errors and external disturbances.
Abstract: The voltage/current characteristics and the effect of
NO2 gas on the electrical conductivity of a PbPc gas sensor array is
investigated. The gas sensor is manufactured using vacuum
deposition of gold electrodes on sapphire substrate with the leadphathalocyanine
vacuum sublimed on the top of the gold electrodes.
Two versions of the PbPc gas sensor array are investigated. The
tested types differ in the gap sizes between the deposited gold
electrodes. The sensors are tested at different temperatures to account
for conductivity changes as the molecular adsorption/desorption rate
is affected by heat. The obtained results found to be encouraging as
the sensors shoed stability and sensitivity towards low concentration
of applied NO2 gas.
Abstract: In this study, the possibility of using potato as a
substrate for glutamic acid production by Brevibacterium linens
was investigated. For preparation of fermentation medium, potato
was hydrolyzed by hydrochloridric acid. The medium contained
potato hydrolysate, tween 80, mineral solution, glucose, and
potassium hydrogen phosphate. The initial pH of the medium was
adjusted to 7-7.5. For achieving the optimum time with maximum
yield, the beakers containing the medium and the inoculums were
incubated in a rotary water bath flask shaker for one to five days.
Thin layer choromatography was used for quantitative and
qualitative assay of the glutamic acid produced. The results
revealed that as fermentation time increased, pH of the
fermentation medium significantly decreased (P
Abstract: Atmospheric plasma is emerging as a promising
technology for many industrial sectors, because of its ecological and
economic advantages respect to the traditional production processes.
For textile industry, atmospheric plasma is becoming a valid
alternative to the conventional wet processes, but the plasma
machines realized so far do not allow the treatment of fibrous
mechanically weak material.
Novel atmospheric plasma machine for industrial applications,
developed by VenetoNanotech SCpA in collaboration with Italian
producer of corona equipment ME.RO SpA is presented. The main
feature of this pre-industrial scale machine is the possibility of the inline
plasma treatment of delicate fibrous substrates such as fibre
sleeves, for example wool tops, cotton fibres, polymeric tows,
mineral fibers and so on, avoiding burnings and disruption of the
faint materials.
Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: This paper reports on the theoretical performance
analysis of the 1.3 μm In0.42Ga0.58As /In0.26Ga0.74As multiple quantum
well (MQW) vertical cavity surface emitting laser (VCSEL) on the
ternary In0.31Ga0.69As substrate. The output power of 2.2 mW has
been obtained at room temperature for 7.5 mA injection current. The
material gain has been estimated to be ~3156 cm-1 at room
temperature with the injection carrier concentration of 2×1017 cm-3.
The modulation bandwidth of this laser is measured to be 9.34 GHz
at room temperature for the biasing current of 2 mA above the
threshold value. The outcomes reveal that the proposed InGaAsbased
MQW laser is the promising one for optical communication
system.
Abstract: The crystalline quality of the AlGaN/GaN high electron mobility transistor (HEMT) structure grown on a 200 mm silicon substrate has been investigated using UV-visible micro- Raman scattering and photoluminescence (PL). The visible Raman scattering probes the whole nitride stack with the Si substrate and shows the presence of a small component of residual in-plane stress in the thick GaN buffer resulting from a wafer bowing, while the UV micro-Raman indicates a tensile interfacial stress induced at the top GaN/AlGaN/AlN layers. PL shows a good crystal quality GaN channel where the yellow band intensity is very low compared to that of the near-band-edge transition. The uniformity of this sample is shown by measurements from several points across the epiwafer.
Abstract: Batch fermentation of 5, 10 and 25 g/L biodiesel
derived crude glycerol was carried out at 30, 37 and 450C by
Clostridium pasteurianum cells immobilized on silica. Maximum
yield of 1,3-propanediol (PDO) (0.60 mol/mol), and ethanol (0.26
mol/mol) were obtained from 10 g/L crude glycerol at 30 and 370C
respectively. Maximum yield of butanol (0.28 mol/mol substrate
added) was obtained at 370C with 25 g/L substrate. None of the three
products were detected at 45oC even after 10 days of fermentation.
Only traces of ethanol (0.01 mol/mol) were detected at 450C with 5
g/L substrate. The results obtained for 25 g/L substrate utilization
were fitted in first order rate equation to obtain the values of rate
constant at three different temperatures for bioconversion of glycerol.
First order rate constants for bioconversion of glycerol at 30, 37 and
45oC were found to be 0.198, 0.294 and 0.029/day respectively.
Activation energy (Ea) for crude glycerol bioconversion was
calculated to be 57.62 kcal/mol.
Abstract: We report a lithography-free approach to fabricate the
biomimetics, quasi-beehive Si nanostructures (QBSNs), on
Si-substrates. The self-assembled SiGe nanoislands via the strain
induced surface roughening (Asaro-Tiller-Grinfeld instability) during
in-situ annealing play a key role as patterned sacrifice regions for
subsequent reactive ion etching (RIE) process performed for
fabricating quasi-beehive nanostructures on Si-substrates. As the
measurements of field emission, the bare QBSNs show poor field
emission performance, resulted from the existence of the native oxide
layer which forms an insurmountable barrier for electron emission. In
order to dramatically improve the field emission characteristics, the
platinum nanopillars (Pt-NPs) were deposited on QBSNs to form
Pt-NPs/QBSNs heterostructures. The turn-on field of Pt-NPs/QBSNs
is as low as 2.29 V/μm (corresponding current density of 1 μA/cm2),
and the field enhancement factor (β-value) is significantly increased to
6067. More importantly, the uniform and continuous electrons excite
light emission, due to the surrounding filed emitters from
Pt-NPs/QBSNs, can be easily obtained. This approach does not require
an expensive photolithographic process and possesses great potential
for applications.
Abstract: A diamond-like carbon (DLC) based solid-lubricant
film was designed and DLC films were successfully prepared using a
microwave plasma enhanced magnetron sputtering deposition
technology. Post-test characterizations including Raman
spectrometry, X-ray diffraction, nano-indentation test, adhesion test,
friction coefficient test were performed to study the influence of
substrate bias voltage on the mechanical properties of the W- and
S-doped DLC films. The results indicated that the W- and S-doped
DLC films also had the typical structure of DLC films and a better
mechanical performance achieved by the application of a substrate
bias of -200V.
Abstract: A numerical study on the heat transfer in the thermal
barrier coatings and the substrates of a parallel-plate enclosure is
carried out. Some of the thermal barrier coatings, such as ceramics, are
semitransparent and are of interest for high-temperature applications
where radiation effects are significant. The radiative transfer equations
and the energy equations are solved by using the discrete ordinates
method and the finite difference method. Illustrative results are
presented for temperature distributions in the coatings and the opaque
walls under various heating conditions. The results show that the
temperature distribution is more uniform in the interior portion of each
coating away from its boundary for the case with a larger average of
varying refractive index and a positive gradient of refractive index
enhances radiative transfer to the substrates.