Abstract: This paper describes the development of new class of
epoxy based rice husk filled jute reinforced composites. Rice husk
flour is added in 0%, 1%, 3%, 5% by weight. Epoxy resin and
triethylenetetramine (T.E.T.A) is used as matrix and hardener
respectively. It investigates the mechanical properties of the
composites and a comparison is done for monolithic jute composite
and the filled ones. The specimens are prepared according to the
ASTM standards and experimentation is carried out using INSTRON
8801. The result shows that with the increase of filler percentage the
tensile properties increases but compressive and flexural properties
decreases.
Abstract: The quality of concrete is usually defined by compressive strength, but flexural strength is the most important characteristic of concrete in a pavement which control the mix design of concrete instead of compressive strength. Therefore, the aggregates which are selected for the pavements are affected by higher flexural strength. Roller Compacting Concrete Pavement (RCCP) is not a new construction method. The other characteristic of this method is no bleeding and less shrinkage due to the lower amount of water. For this purpose, a roller is needed for placing and compacting. The surface of RCCP is not smooth; therefore, the most common use of this pavement is in an industrial zone with slower traffic speed which requires durable and tough pavement. For preparing a smoother surface, it can be achieved by asphalt paver. RCCP decrease the finishing cost because there are no bars, formwork, and the lesser labor need for placing the concrete. In this paper, different aspect of RCCP such as mix design, flexural, compressive strength and focus on the different part of RCCP on detail have been investigated.
Abstract: As one of the convenient and noninvasive sensing
approaches, the automatic limb girth measurement has been applied
to detect intention behind human motion from muscle deformation.
The sensing validity has been elaborated by preliminary researches
but still need more fundamental studies, especially on kinetic
contraction modes. Based on the novel fabric strain sensors, a soft
and smart limb girth measurement system was developed by the
authors’ group, which can measure the limb girth in-motion.
Experiments were carried out on elbow isometric flexion and elbow
isokinetic flexion (biceps’ isokinetic contractions) of 90°/s, 60°/s, and
120°/s for 10 subjects (2 canoeists and 8 ordinary people). After
removal of natural circumferential increments due to elbow position,
the joint torque is found not uniformly sensitive to the limb
circumferential strains, but declining as elbow joint angle rises,
regardless of the angular speed. Moreover, the maximum joint torque
was found as an exponential function of the joint’s angular speed.
This research highly contributes to the application of the automatic
limb girth measuring during kinetic contractions, and it is useful to
predict the contraction level of voluntary skeletal muscles.
Abstract: The change of conditions for production companies in
high-wage countries is characterized by the globalization of
competition and the transition of a supplier´s to a buyer´s market. The
companies need to face the challenges of reacting flexibly to these
changes. Due to the significant and increasing degree of automation,
assembly has become the most expensive production process.
Regarding the reduction of production cost, assembly consequently
offers a considerable rationalizing potential. Therefore, an
aerodynamic feeding system has been developed at the Institute of
Production Systems and Logistics (IFA), Leibniz Universitaet
Hannover. This system has been enabled to adjust itself by using a
genetic algorithm. The longer this genetic algorithm is executed the
better is the feeding quality. In this paper, the relation between the
system´s setting time and the feeding quality is observed and a
function which enables the user to achieve the minimum of the total
feeding time is presented.
Abstract: Escherichia coli (E. coli) is the most isolated bacteria
from blood circulation of septicemic calves. Given the prevalence of
septicemia in animals and its economic importance in veterinary
practice, better understanding of changes in clinical signs following
disease, may contribute to early detection of disorder. The present
study has been carried out to detect changes of clinical signs in
induced sepsis in calves with E. coli. Colisepticemia has been
induced in 10 twenty-day old healthy Holstein- Frisian calves with
intravenous injection of 1.5 X 109 colony forming units (cfu) of
O111:H8 strain of E. coli. Clinical signs including rectal temperature,
heart rate, respiratory rate, shock, appetite, sucking reflex, feces
consistency, general behavior, dehydration and standing ability were
recorded in experimental calves during 24 hours after induction of
colisepticemia. Blood culture was also carried out from calves four
times during experiment. ANOVA with repeated measure is used to
see changes of calves’ clinical signs to experimental colisepticemia,
and values of P≤ 0.05 was considered statistically significant. Mean
values of rectal temperature and heart rate as well as median values
of respiratory rate, appetite, suckling reflex, standing ability and feces
consistency of experimental calves increased significantly during
study (P 0.05). The
results of present study showed that total score of clinical signs in
calves with experimental colisepticemia increased significantly,
although score of some clinical signs such as shock did not change
significantly.
Abstract: Geopolymer composites reinforced with flax fabrics
and nanoclay are fabricated and studied for physical and mechanical
properties using X-Ray Diffraction (XRD), Fourier Transform
Infrared Spectroscopy (FTIR), and Scanning Electron Microscope
(SEM). Nanoclay platelets at a weight of 1.0%, 2.0%, and 3.0% were
added to geopolymer pastes. Nanoclay at 2.0 wt.% was found to
improve density and decrease porosity while improving flexural
strength and post-peak toughness. A microstructural analysis
indicated that nanoclay behaves as filler and as an activator
supporting geopolymeric reaction while producing a higher content
geopolymer gel improving the microstructure of binders. The process
enhances adhesion between the geopolymer matrix and flax fibres.
Abstract: Considering the challenges of short product life cycles
and growing variant diversity, cost minimization and manufacturing
flexibility increasingly gain importance to maintain a competitive
edge in today’s global and dynamic markets. In this context, an
aerodynamic part feeding system for high-speed industrial assembly
applications has been developed at the Institute of Production
Systems and Logistics (IFA), Leibniz Universitaet Hannover. The
aerodynamic part feeding system outperforms conventional systems
with respect to its process safety, reliability, and operating speed. In
this paper, a multi-objective optimisation of the aerodynamic feeding
system regarding the orientation rate, the feeding velocity, and the
required nozzle pressure is presented.
Abstract: Durian skin is a newly explores natural fibre
potentially reinforced polyolefin for diverse applications. In this
work, investigation on the effect of coupling agent, maleic anhydride
polypropylene (MAPP) on the mechanical, morphological, and
thermal properties of polypropylene (PP) reinforced with durian skin
fibre (DSF) was conducted. The presence of 30 wt% DSF
significantly reduced the tensile strength of PP-DSF composite.
Interestingly, even though the same trend goes to PP-DSF with the
presence of MAPP, the reduction is only about 4% relative to
unreinforced PP and 18% higher than PP-DSF without MAPP
(untreated composite or UTC). The used of MAPP in treated
composite (TC) also increased the tensile modulus, flexural
properties and degradation temperature. The enhanced mechanical
properties are consistent with good interfacial interaction as
evidenced under scanning electron microscopy.
Abstract: Wind energy is rapidly emerging as the primary
source of electricity in the Philippines, although developing an
accurate wind resource model is difficult. In this study, Weather
Research and Forecasting (WRF) Model, an open source mesoscale
Numerical Weather Prediction (NWP) model, was used to produce a
1-year atmospheric simulation with 4 km resolution on the Ilocos
Region of the Philippines. The WRF output (netCDF) extracts the
annual mean wind speed data using a Python-based Graphical User
Interface. Lastly, wind resource assessment was produced using a
GIS software. Results of the study showed that it is more flexible to
use Python scripts than using other post-processing tools in dealing
with netCDF files. Using WRF Model, Python, and Geographic
Information Systems, a reliable wind resource map is produced.
Abstract: Geological and tectonic framework indicates that
Bangladesh is one of the most seismically active regions in the world.
The Bengal Basin is at the junction of three major interacting plates:
the Indian, Eurasian, and Burma Plates. Besides there are many
active faults within the region, e.g. the large Dauki fault in the north.
The country has experienced a number of destructive earthquakes due
to the movement of these active faults. Current seismic provisions of
Bangladesh are mostly based on earthquake data prior to the 1990.
Given the record of earthquakes post 1990, there is a need to revisit
the design provisions of the code. This paper compares the base shear
demand of three major cities in Bangladesh: Dhaka (the capital city),
Sylhet, and Chittagong for earthquake scenarios of magnitudes
7.0MW, 7.5MW, 8.0MW, and 8.5MW using a stochastic model. In
particular, the stochastic model allows the flexibility to input region
specific parameters such as shear wave velocity profile (that were
developed from Global Crustal Model CRUST2.0) and include the
effects of attenuation as individual components. Effects of soil
amplification were analysed using the Extended Component
Attenuation Model (ECAM). Results show that the estimated base
shear demand is higher in comparison with code provisions leading to
the suggestion of additional seismic design consideration in the study
regions.
Abstract: The aim of the study is to describe and analyze design
of mobile teaching for students collaborative learning in distance
higher education with a focus on mobile technologies as online
webinars (web-based seminars or conferencing) by using laptops,
smart phones, or tablets. These multimedia tools can provide face-toface
interactions, recorded flipped classroom videos and parallel chat
communications. The data collection consists of interviews with 22
students and observations of online face-to-face webinars, as well
two surveys. Theoretically, the study joins the research tradition of
Computer Supported Collaborative learning, CSCL, as well as
Computer Self-Efficacy, CSE concerned with individuals’ media and
information literacy. Important conclusions from the study
demonstrated mobile interactions increased student centered
learning. As the students were appreciating the working methods,
they became more engaged and motivated. The mobile technology
using among student also contributes to increased flexibility between
space and place, as well as media and information literacy.
Abstract: Concurrent planning of project scheduling and
material ordering can provide more flexibility to the project
scheduling problem, as the project execution costs can be enhanced.
Hence, the issue has been taken into account in this paper. To do so, a
mixed-integer mathematical model is developed which considers the
aforementioned flexibility, in addition to the materials quantity
discount and space availability restrictions. Moreover, the activities
duration has been treated as decision variables. Finally, the efficiency
of the proposed model is tested by different instances. Additionally,
the influence of the aforementioned parameters is investigated on the
model performance.
Abstract: The paper will focus on the strategic development
deriving from the evolution of the traditional courtyard spatial
organization towards a new, contemporary sustainable way of living.
New sustainable approaches that engulf the social issues, the notion
of place, the understanding of weather architecture blended together
with the bioclimatic behavior will be seen through a series of
experimental case studies in the island of Cyprus, inspired and
originated from its traditional wisdom, ranging from small scale of
living to urban interventions. Weather and nature will be seen as co-architectural authors with
architects. Furthermore, the building will be seen not as an object but
rather as a vessel of human activities. This will further enhance the
notion of merging the material and immaterial, the built and unbuilt,
subject-human, and the object-building. This eventually will enable
to generate the discussion of the understanding of the building in
relation to the place and its inhabitants, where the human topography
is more important than the material topography. The specificities of
the divided island and the dealing with sites that are in vicinity with
the diving Green Line will further trigger explorations dealing with
the regeneration issues and the social sustainability offering
unprecedented opportunities for innovative sustainable ways of
living. Opening up a discourse with premises of weather-nature, materialimmaterial,
human-material topographies in relation to the contested
sites of the borders will lead us to develop innovative strategies for a
profound, both technical and social sustainability, which fruitfully
yields to innovative living built environments, responding to the ever
changing environmental and social needs. As a starting point, a case study in Kaimakli in Nicosia, a
refurbishment with an extension of a traditional house, already
engulfs all the traditional/ vernacular wisdom of the bioclimatic
architecture. The project focusses on the direct and quite obvious
bioclimatic features such as south orientation and cross ventilation.
Furthermore, it tries to reinvent the adaptation of these parameters in
order to turn the whole house to a contemporary living environment.
In order to succeed this, evolutions of traditional architectural
elements and spatial conditions are integrated in a way that does not
only respond to some certain weather conditions, but they integrate
and blend the weather within the built environment. A series of
innovations aiming at maximum flexibility is proposed. The house
can finally be transformed into a winter enclosure, while for the most
part of the year it turns into a ‘camping’ living environment. Parallel to experimental interventions in existing traditional units,
we will proceed examining the implementation of the same
developed methodology in designing living units and complexes.
Malleable courtyard organizations that attempt to blend the
traditional wisdom with the contemporary needs for living, the
weather and nature with the built environment will be seen tested in
both horizontal and vertical developments. Social activities are seen as directly affected and forged by the
weather conditions thus generating a new social identity of people where people are directly involved and interacting with the weather.
The human actions and interaction with the built, material
environment in order to respond to weather will be seen as the result
of balancing the social with the technological sustainability, the
immaterial, and the material aspects of the living environment.
Abstract: The objective of this study was to synthesize and
characterize the poly(alkenoic acid)s with different molecular
structures, use these polymers to formulate a dental cement
restorative, and study the effect of molecular structures on reaction
kinetics, viscosity, and mechanical strengths of the formed polymers
and cement restoratives. In this study, poly(alkenoic acid)s with
different molecular structures were synthesized. The purified
polymers were formulated with commercial Fuji II LC glass fillers to
form the experimental cement restoratives. The reaction kinetics was
studied via 1HNMR spectroscopy. The formed restoratives were
evaluated using compressive strength, diametral tensile strength,
flexural strength, hardness and wear-resistance tests. Specimens were
conditioned in distilled water at 37oC for 24 h prior to testing. Fuji II
LC restorative was used as control. The results show that the higher
the arm number and initiator concentration, the faster the reaction
was. It was also found that the higher the arm number and branching
that the polymer had, the lower the viscosity of the polymer in water
and the lower the mechanical strengths of the formed restorative. The
experimental restoratives were 31-53% in compressive strength, 37-
55% in compressive modulus, 80-126% in diametral tensile strength,
76-94% in flexural strength, 4-21% in fracture toughness and 53-96%
in hardness higher than Fuji II LC. For wear test, the experimental
restoratives were only 5.4-13% of abrasive and 6.4-12% of attritional
wear depths of Fuji II LC in each wear cycle. The aging study also
showed that all the experimental restoratives increased their strength
continuously during 30 days, unlike Fuji II LC. It is concluded that
polymer molecular structures have significant and positive impact on
mechanical properties of dental cement restoratives.
Abstract: Increasingly complex modern power systems require
stability, especially for transient and small disturbances. Transient
stability plays a major role in stability during fault and large
disturbance. This paper compares a power system stabilizer (PSS)
and static Var compensator (SVC) to improve damping oscillation
and enhance transient stability. The effectiveness of a PSS connected
to the exciter and/or governor in damping electromechanical
oscillations of isolated synchronous generator was tested. The SVC
device is a member of the shunt FACTS (flexible alternating current
transmission system) family, utilized in power transmission systems.
The designed model was tested with a multi-machine system
consisting of four machines six bus, using MATLAB/SIMULINK
software. The results obtained indicate that SVC solutions are better
than PSS.
Abstract: Lateral torsional buckling is a global buckling mode
which should be considered in design of slender structural members
under flexure about their strong axis. It is possible to compute the
load which causes lateral torsional buckling of a beam by finite
element analysis, however, closed form equations are needed in
engineering practice for calculation ease which can be obtained by
using energy method. In lateral torsional buckling applications of
energy method, a proper function for the critical lateral torsional
buckling mode should be chosen which can be thought as the
variation of twisting angle along the buckled beam. Accuracy of the
results depends on how close is the chosen function to the exact
mode. Since critical lateral torsional buckling mode of the cantilever
I-beams varies due to material properties, section properties and
loading case, the hardest step is to determine a proper mode function
in application of energy method. This paper presents an approximate function for critical lateral
torsional buckling mode of doubly symmetric cantilever I-beams.
Coefficient matrices are calculated for concentrated load at free end,
uniformly distributed load and constant moment along the beam
cases. Critical lateral torsional buckling modes obtained by presented
function and exact solutions are compared. It is found that the modes
obtained by presented function coincide with differential equation
solutions for considered loading cases.
Abstract: The paper shows that on transferring sense from the
SL to the TL, the translator’s reading against the grain determines the
creation of a faulty pattern of rendering the original meaning in the
receiving culture which reflects the use of misleading transformative
codes. In this case, the translator is a writer per se who decides what
goes in and out of the book, how the style is to be ciphered and what
elements of ideology are to be highlighted. The paper also proves that
figurative language must not be flattened for the sake of clarity or
naturalness. The missing figurative elements make the translated text
less interesting, less challenging and less vivid which reflects poorly
on the writer. There is a close connection between style and the
writer’s person. If the writer’s style is very much altered in a
translation, the translation is useless as the original writer and his /
her imaginative world can no longer be discovered. The purpose of the paper is to prove that adaptation is a dangerous
tool which leads to variants that sometimes reflect the original less
than the reader would wish to. It contradicts the very essence of the
process of translation which is that of making an original work
available in a foreign language. If the adaptive transformative codes
are so flexible that they encourage the translator to repeatedly leave
out parts of the original work, then a subversive pattern emerges
which changes the entire book. In conclusion, as a result of using adaptation, manipulative or
subversive effects are created in the translated work. This is generally
achieved by adding new words or connotations, creating new figures
of speech or using explicitations. The additional meanings of the
original work are neglected and the translator creates new meanings,
implications, emphases and contexts. Again s/he turns into a new
author who enjoys the freedom of expressing his / her own ideas
without the constraints of the original text. Reading against the grain
is unadvisable during the process of translation and consequently,
following personal common sense becomes essential in the field of
translation as well as everywhere else, so that translation should not
become a source of fantasy.
Abstract: In this article, the radial displacement error correction
capability of a high precision spindle grinding caused by unbalance
force was investigated. The spindle shaft is considered as a flexible
rotor mounted on two sets of angular contact ball bearing. Finite
element methods (FEM) have been adopted for obtaining the
equation of motion of the spindle. In this paper, firstly, natural
frequencies, critical frequencies, and amplitude of the unbalance
response caused by residual unbalance are determined in order to
investigate the spindle behaviors. Furthermore, an optimization
design algorithm is employed to minimize radial displacement of the
spindle which considers dimension of the spindle shaft, the dynamic
characteristics of the bearings, critical frequencies and amplitude of
the unbalance response, and computes optimum spindle diameters
and stiffness and damping of the bearings. Numerical simulation
results show that by optimizing the spindle diameters, and stiffness
and damping in the bearings, radial displacement of the spindle can
be reduced. A spindle about 4 μm radial displacement error can be
compensated with 2 μm accuracy. This certainly can improve the
accuracy of the product of machining.
Abstract: The study conducted a simulation of the effect of sea
water to the bonding capacity of GFRP sheet on the concrete beams
using a simulation tank. Fiber reinforced polymer (FRP) has been
developed and applied in many fields civil engineering structures on
the new structures and also for strengthening of the deteriorated
structures. The FRP has advantages such as its corrosion resistance as
well as high tensile strength to weight ratio. Compared to the other
FRP materials, Glass composed FRP (GFRP) is relatively cheaper.
GFRP sheet is applied externally by bonding it on the concrete surface.
The studies regarding the application of GFRP sheet have been
conducted such as strengthening system, bonding behavior of GFRP
sheet including the application as reinforcement in new structures. For
application to the structures with direct contact to sea environment, a
study regarding the effect of sea water to the bonding capacity of
GFRP sheet is important to be clarified. To achieve the objective of the
study, a series of concrete beams strengthened with GFRP sheet on
extreme tension surface were prepared. The beams then were stored on
the sea water tank for six months. Results indicated the bonding
capacity decreased after six month exposed to the sea water.
Abstract: In recent years, the power system has been changed
and a flexible power pricing system such as demand response has been
sought in Japan. The demand response system works simply in the
household sector and the owner as the decision-maker, can benefit
from power saving. On the other hand, the execution of demand
response in the office building is more complex than in the household
because various people such as owners, building administrators and
occupants are involved in the decision-making process. While the
owners benefit from demand saving, the occupants are exposed to
restricted benefits of a demand-saved environment. One of the reasons
is that building systems are usually under centralized management and
each occupant cannot choose freely whether to participate in demand
response or not. In addition, it is unclear whether incentives give
occupants the motivation to participate. However, the recent
development of IT and building systems enables the personalized
control of the office environment where each occupant can control the
lighting level or temperature individually. Therefore, it can be possible
to have a system which each occupant can make a decision of whether
or not to participate in demand response in the office building. This study investigates personal responses to demand response
requests, under the condition where each occupant can adjust their
brightness individually in their workspace. Once workers participate
in the demand response, their desk-lights are automatically turned off.
The participation rates in the demand response events are compared
among four groups, which are divided by different motivation, the
presence, or absence of incentives and the method of participation. The
result shows that there are significant differences of participation rates
in demand response event between four groups. The method of
participation has a large effect on the participation rate. The “Opt-out”
groups where the occupants are automatically enrolled in a demand
response event if they do not express non-participation have the
highest participation rate in the four groups. Incentives also have an
effect on the participation rate. This study also reports on the impact of low illumination office
environment on the occupants, such as stress or fatigue. The
electrocardiogram and the questionnaire are used to investigate the
autonomic nervous activity and subjective fatigue symptoms of the
occupants. There is no big difference between dim workspace during
demand response event and bright workspace in autonomic nervous
activity and fatigue.