Abstract: This paper focuses on a novel method for semantic
searching and retrieval of information about learning materials.
Metametadata encapsulate metadata instances by using the properties
and attributes provided by ontologies rather than describing learning
objects. A novel metametadata taxonomy has been developed which
provides the basis for a semantic search engine to extract, match and
map queries to retrieve relevant results. The use of ontological views
is a foundation for viewing the pedagogical content of metadata
extracted from learning objects by using the pedagogical attributes
from the metametadata taxonomy. Using the ontological approach
and metametadata (based on the metametadata taxonomy) we present
a novel semantic searching mechanism.These three strands – the
taxonomy, the ontological views, and the search algorithm – are
incorporated into a novel architecture (OMESCOD) which has been
implemented.
Abstract: The friction between two metal surfaces results in a
high frequency noise (squealing) which also occurs during the
braking of wagons with rail brakes in the process of shunting at a
marshalling yard with a hump. At that point the noise level may
exceed 130dB, which is extremely unpleasant for workers and
inhabitants. In our research we developed a new composite material
which does not change braking properties, is capable of taking
extremely high pressure loads, reduces noise and is environmentally
friendly. The noise reduction results had been very good and had
shown a decrease of the high frequency noise almost completely (by
99%) at its source. With our technology we had also reduced general
noise by more than 30dBA.
Abstract: Within this work High Temperature Single Impact
Studies were performed to evaluate deformation mechanisms at
different energy and momentum levels. To show the influence of
different microstructures and hardness levels and their response to
single impacts four different materials were tested at various
temperatures up to 700°C. One carbide reinforced NiCrBSi based
Metal Matrix Composite and three different steels were tested. The
aim of this work is to determine critical energies for fracture
appearance and the materials response at different energy and
momenta levels. Critical impact loadings were examined at elevated
temperatures to limit operating conditions in impact dominated
regimes at elevated temperatures. The investigations on the
mechanisms were performed using different means of microscopy at
the surface and in metallographic cross sections. Results indicate
temperature dependence of the occurrence of cracks in hardphase
rich materials, such as Metal Matrix Composites High Speed Steels
and the influence of different impact momenta at constant energies
on the deformation of different steels.
Abstract: In recent years linguistic research has turned
increasing attention to covert/overt strategies to modulate authorial
stance and positioning in scientific texts, and to the recipients'
response. This study discussed some theoretical implications of the
use of rhetoric in scientific communication and analysed qualitative
data from the authoritative The Cognitive Neurosciences III (2004)
volume. Its genre-identity, status and readability were considered, in
the social interactive context of contemporary disciplinary discourses
– in their polyphony of traditional and new, emerging genres.
Evidence was given of the ways its famous authors negotiate and
shape knowledge and research results – explicitly appraising team
work and promoting faith in the fast-paced progress of Cognitive
Neuroscience, also through experiential metaphors – by presenting a
set of examples, ordered according to their dominant rhetorical
quality.
Abstract: Today, transport and logistic systems are often tightly
integrated in the production. Lean production and just-in-time delivering create multiple constraints that have to be fulfilled. As transport networks often have evolved over time they are very
expensive to change. This paper describes a discrete-event-simulation
system which simulates transportation models using real time
resource routing and collision avoidance. It allows for the
specification of own control algorithms and validation of new
strategies. The simulation is integrated into a virtual reality (VR)
environment and can be displayed in 3-D to show the progress.
Simulation elements can be selected through VR metaphors. All data
gathered during the simulation can be presented as a detailed summary afterwards. The included cost-benefit calculation can help to optimize the financial outcome. The operation of this approach is shown by the example of a timber harvest simulation.
Abstract: Magnetic and semiconductor nanomaterials exhibit
novel magnetic and optical properties owing to their unique size and
shape-dependent effects. With shrinking the size down to nanoscale
region, various anomalous properties that normally not present in bulk
start to dominate. Ability in harnessing of these anomalous properties
for the design of various advance electronic devices is strictly
dependent on synthetic strategies. Hence, current research has focused
on developing a rational synthetic control to produce high quality
nanocrystals by using organometallic approach to tune both size and
shape of the nanomaterials. In order to elucidate the growth
mechanism, transmission electron microscopy was employed as a
powerful tool in performing real time-resolved morphologies and
structural characterization of magnetic (Fe3O4) and semiconductor
(ZnO) nanocrystals. The current synthetic approach is found able to
produce nanostructures with well-defined shapes. We have found that
oleic acid is an effective capping ligand in preparing oxide-based
nanostructures without any agglomerations, even at high temperature.
The oleate-based precursors and capping ligands are fatty acid
compounds, which are respectively originated from natural palm oil
with low toxicity. In comparison with other synthetic approaches in
producing nanostructures, current synthetic method offers an effective
route to produce oxide-based nanomaterials with well-defined shapes
and good monodispersity. The nanocystals are well-separated with
each other without any stacking effect. In addition, the as-synthesized
nanopellets are stable in terms of chemically and physically if
compared to those nanomaterials that are previous reported. Further
development and extension of current synthetic strategy are being
pursued to combine both of these materials into nanocomposite form
that will be used as “smart magnetic nanophotocatalyst" for industry
waste water treatment.
Abstract: Presents a concept for a multidisciplinary process
supporting effective task transitions between different technical
domains during the architectural design stage.
A system configuration challenge is the multifunctional driven
increased solution space. As a consequence, more iteration is needed
to find a global optimum, i.e. a compromise between involved
disciplines without negative impact on development time. Since state
of the art standards like ISO 15288 and VDI 2206 do not provide a
detailed methodology on multidisciplinary design process, higher
uncertainties regarding final specifications arise. This leads to the
need of more detailed and standardized concepts or processes which
could mitigate risks.
The performed work is based on analysis of multidisciplinary
interaction, of modeling and simulation techniques. To demonstrate
and prove the applicability of the presented concept, it is applied to
the design of aircraft high lift systems, in the context of the
engineering disciplines kinematics, actuation, monitoring, installation
and structure design.
Abstract: This paper presents a new system developed in Java®
for pattern recognition and pattern summarisation in multi-band
(RGB) satellite images. The system design is described in some
detail. Results of testing the system to analyse and summarise
patterns in SPOT MS images and LANDSAT images are also
discussed.
Abstract: Various assisted reproductive techniques have been
developed and refined to obtain a large number of offspring from
genetically superior animals or obtain offspring from infertile (or
subfertile) animals. The embryo transfer is one assisted reproductive
technique developed well, aimed at increased productivity of selected
females, disease control, importation and exportation of livestock,
rapid screening of AI sires for genetically recessive characteristics,
treatment or circumvention of certain types of infertility. Embryo
transfer also is a useful research tool for evaluating fetal and maternal
interactions. This technique has been applied to nearly every species
of domestic animal and many species of wildlife and exotic animals,
including humans and non-human primates. The successful of
embryo transfers have been limited to within-animal, homologous
replacement of the embryos. There are several examples of
interspecific and intergeneric embryo transfers in which embryos
implanted but did not develop to term: sheep and goat, mouse and rat.
An immunological rejections and placental incompatibility between
the embryo and the surrogate mother appear to restrict interspecific
embryo transfer/interspecific pregnancy. Recently, preimplantation
embryo manipulation procedures have been applied, such as
technique of inner cell mass transfer. This technique will possible to
overcome the reproductive barrier interspecific embryo
transfer/interspecific pregnancy, if there is a protective mechanism
which prevents recognition of the foreign fetus by the mother of the
other species
Abstract: commercially produced in Malaysia granular
palm shell activated carbon (PSAC) was biomodified with
bacterial biomass (Bacillus subtilis) to produce a hybrid
biosorbent of higher efficiency. The obtained biosorbent was
evaluated in terms of adsorption capacity to remove copper
and zinc metal ions from aqueous solutions. The adsorption
capacity was evaluated in batch adsorption experiments where
concentrations of metal ions varied from 20 to 350 mg/L. A
range of pH from 3 to 6 of aqueous solutions containing metal
ions was tested. Langmuir adsorption model was used to
interpret the experimental data. Comparison of the adsorption
data of the biomodified and original palm shell activated
carbon showed higher uptake of metal ions by the hybrid
biosorbent. A trend in metal ions uptake increase with the
increase in the solution-s pH was observed. The surface
characterization data indicated a decrease in the total surface
area for the hybrid biosorbent; however the uptake of copper
and zinc by it was at least equal to the original PSAC at pH 4
and 5. The highest capacity of the hybrid biosorbent was
observed at pH 5 and comprised 22 mg/g and 19 mg/g for
copper and zinc, respectively. The adsorption capacity at the
lowest pH of 3 was significantly low. The experimental results
facilitated identification of potential factors influencing the
adsorption of copper and zinc onto biomodified and original
palm shell activated carbon.
Abstract: Batteries and fuel cells contain a great potential to back up severe photovoltaic power fluctuations under inclement weather conditions. In this paper comparison between batteries and fuel cells is carried out in detail only for their PV power backup options, so their common attributes and different attributes is discussed. Then, the common and different attributes are compared; accordingly, the fuel cell is selected as the backup of Photovoltaic system. Finally, environmental evaluation of the selected hybrid plant was made in terms of plant-s land requirement and lifetime CO2 emissions, and then compared with that of the conventional fossilfuel power generating forms.
Abstract: On the basis of questionnaires and interviews of two samples of subjects (French and Anglo-Saxon) for which two food products were presented (one of the subject’s country and one of the foreign country), we have shown how consumers could be sensitive to the label or brand written on the package of the food product. Furthermore, in the light of Intersubjectivity theory, we have shown the necessity for the consumer to find congruence between the direct and meta perspective towards the product for which the producer and especially the marketer is responsible. Taking into account these findings may help to avoid the commercial failure of a brand while exported abroad.
Abstract: Smoke from domestic wood burning has been
identified as a major contributor to air pollution, motivating detailed
emission measurements under controlled conditions. A series of
experiments was performed to characterise the emissions from wood
combustion in a fireplace and in a woodstove of two common species
of trees grown in Spain: Pyrenean oak (Quercus pyrenaica) and
black poplar (Populus nigra). Volatile organic compounds (VOCs) in
the exhaust emissions were collected in Tedlar bags, re-sampled in
sorbent tubes and analysed by thermal desorption-gas
chromatography-flame ionisation detection. Pyrenean oak presented
substantially higher emissions in the woodstove than in the fireplace,
for the majority of compounds. The opposite was observed for
poplar. Among the 45 identified species, benzene and benzenerelated
compounds represent the most abundant group, followed by
oxygenated VOCs and aliphatics. Emission factors obtained in this
study are generally of the same order than those reported for
residential experiments in the USA.
Abstract: There are so many databases of various fields of life sciences available online. To find well-used databases, a survey to measure life science database citation frequency in scientific literatures is done. The survey is done by measuring how many scientific literatures which are available on PubMed Central archive cited a specific life science database. This paper presents and discusses the results of the survey.
Abstract: The need to have standards has always been a priority
of all the disciplines in the world. Today, standards such as XML and
USB are trying to create a universal interface for their respective
areas. The information regarding every family in the discipline
addressed, must have a lot in common, known as Metadata. A lot of
work has been done in specific domains such as IEEE LOM and
MPEG-7 but they do not appeal to the universality of creating
Metadata for all entities, where we take an entity (object) as, not
restricted to Software Terms. This paper tries to address this problem
of universal Metadata Definition which may lead to increase in
precision of search.
Abstract: In this study, multiwall carbon nanotubes (MWNTs)
were modified with nitric acid chemically and by dielectric barrier
discharge (DBD) plasma in an oxygen-based atmosphere. Used
carbon nanotubes (CNTs) were prepared by chemical vapour
deposition (CVD) floating catalyst method. For removing amorphous
carbon and metal catalyst, MWNTs were exposed to dry air and
washed with hydrochloric acid. Heating purified CNTs under helium
atmosphere caused elimination of acidic functional groups. Fourier
transformed infrared spectroscopy (FTIR) shows formation of
oxygen containing groups such as C=O and COOH. Brunauer,
Emmett, Teller (BET) analysis revealed that functionalization causes
generation of defects on the sidewalls and opening of the ends of
CNTs. Results of temperature-programmed desorption (TPD) and gas
chromatography(GC) indicate that nitric acid treatment create more
acidic groups than plasma treatment.
Abstract: CIM is the standard formalism for modeling management
information developed by the Distributed Management Task
Force (DMTF) in the context of its WBEM proposal, designed to
provide a conceptual view of the managed environment. In this
paper, we propose the inclusion of formal knowledge representation
techniques, based on Description Logics (DLs) and the Web Ontology
Language (OWL), in CIM-based conceptual modeling, and then we
examine the benefits of such a decision. The proposal is specified as a
CIM metamodel level mapping to a highly expressive subset of DLs
capable of capturing all the semantics of the models. The paper shows
how the proposed mapping can be used for automatic reasoning
about the management information models, as a design aid, by means
of new-generation CASE tools, thanks to the use of state-of-the-art
automatic reasoning systems that support the proposed logic and use
algorithms that are sound and complete with respect to the semantics.
Such a CASE tool framework has been developed by the authors and
its architecture is also introduced. The proposed formalization is not
only useful at design time, but also at run time through the use of
rational autonomous agents, in response to a need recently recognized
by the DMTF.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.
Abstract: Malate dehydrogenase-glutamate oxaloacetate
aminotransferase (MDh-GOAT) enzyme complex (the EC) was
isolated and purified from wheat and rise, their some main physicchemical
properties were studied. Michael-s constants of the EC
MDh-GOAT to malate, glutamate and NAD were investigated. This
kinetic results show a high relationship to glutamate. Taking into
account important role of the the EC in catabolism of glutamate – the
central amino acid of a nitric exchange, there is a sharp necessity of
deeper studying of this enzyme complex. Therefore the basic purpose
of the work is studying the basic physical and chemical properties of
this enzyme complex discovered by us, which would be very
important for understanding the mechanisms of reaction catalyzed by
the EC.
Abstract: The avian phytohaemagglutinin skin test is being
proved as an in vivo system for the evaluation an avian in vivo T cell
mitogenicity. The test system was one week old Gallus domesticus
broiler Chickens. Five replicates were done for each of the whole,
1:10 dilutions of each of 0.05 IU tuberculin, tetanus immunoglobulin
and DPT vaccine as test materials. The evaluation parameters were
the skin indurations and lymphoblast percentages in bone marrow
lymphocytes.
Tuberculin indurations were 2.06 and 1.26mm for 0.05 IU
respectively while lymphoblast percent were 0.234 and 0.1
accordingly.
The skin indurations of 135mg/ml and 1.35mg/ml tetanus
immunoglobulin were 4.86 and 3.96mm while lymphoblast
percentages were 0.3 and 0.14 respectively.
The whole DPT and 1:10 concentration were with 4.5 and 3.2mm
while their lymphoblast percentages were 0.28 and 0.12 accordingly.
Thus the mitogenicity of the test materials was of dependant type.