Abstract: This paper presents a comparative analysis of a new
unsupervised PCA-based technique for steel plates texture segmentation
towards defect detection. The proposed scheme called Variance
Based Component Analysis or VBCA employs PCA for feature
extraction, applies a feature reduction algorithm based on variance of
eigenpictures and classifies the pixels as defective and normal. While
the classic PCA uses a clusterer like Kmeans for pixel clustering,
VBCA employs thresholding and some post processing operations to
label pixels as defective and normal. The experimental results show
that proposed algorithm called VBCA is 12.46% more accurate and
78.85% faster than the classic PCA.
Abstract: Content-Based Image Retrieval has been a major area
of research in recent years. Efficient image retrieval with high
precision would require an approach which combines usage of both
the color and texture features of the image. In this paper we propose
a method for enhancing the capabilities of texture based feature
extraction and further demonstrate the use of these enhanced texture
features in Texture-Based Color Image Retrieval.
Abstract: Effectiveness of Artificial Neural Networks (ANN)
and Support Vector Machines (SVM) classifiers for fault diagnosis of
rolling element bearings are presented in this paper. The
characteristic features of vibration signals of rotating driveline that
was run in its normal condition and with faults introduced were used
as input to ANN and SVM classifiers. Simple statistical features such
as standard deviation, skewness, kurtosis etc. of the time-domain
vibration signal segments along with peaks of the signal and peak of
power spectral density (PSD) are used as features to input the ANN
and SVM classifier. The effect of preprocessing of the vibration
signal by Discreet Wavelet Transform (DWT) prior to feature
extraction is also studied. It is shown from the experimental results
that the performance of SVM classifier in identification of bearing
condition is better then ANN and pre-processing of vibration signal
by DWT enhances the effectiveness of both ANN and SVM classifier
Abstract: The design of a pattern classifier includes an attempt
to select, among a set of possible features, a minimum subset of
weakly correlated features that better discriminate the pattern classes.
This is usually a difficult task in practice, normally requiring the
application of heuristic knowledge about the specific problem
domain. The selection and quality of the features representing each
pattern have a considerable bearing on the success of subsequent
pattern classification. Feature extraction is the process of deriving
new features from the original features in order to reduce the cost of
feature measurement, increase classifier efficiency, and allow higher
classification accuracy. Many current feature extraction techniques
involve linear transformations of the original pattern vectors to new
vectors of lower dimensionality. While this is useful for data
visualization and increasing classification efficiency, it does not
necessarily reduce the number of features that must be measured
since each new feature may be a linear combination of all of the
features in the original pattern vector. In this paper a new approach is
presented to feature extraction in which feature selection, feature
extraction, and classifier training are performed simultaneously using
a genetic algorithm. In this approach each feature value is first
normalized by a linear equation, then scaled by the associated weight
prior to training, testing, and classification. A knn classifier is used to
evaluate each set of feature weights. The genetic algorithm optimizes
a vector of feature weights, which are used to scale the individual
features in the original pattern vectors in either a linear or a nonlinear
fashion. By this approach, the number of features used in classifying
can be finely reduced.
Abstract: This paper presents a new system developed in Java®
for pattern recognition and pattern summarisation in multi-band
(RGB) satellite images. The system design is described in some
detail. Results of testing the system to analyse and summarise
patterns in SPOT MS images and LANDSAT images are also
discussed.
Abstract: In this paper a new approach to face recognition is
presented that achieves double dimension reduction, making the
system computationally efficient with better recognition results and
out perform common DCT technique of face recognition. In pattern
recognition techniques, discriminative information of image
increases with increase in resolution to a certain extent, consequently
face recognition results change with change in face image resolution
and provide optimal results when arriving at a certain resolution
level. In the proposed model of face recognition, initially image
decimation algorithm is applied on face image for dimension
reduction to a certain resolution level which provides best
recognition results. Due to increased computational speed and feature
extraction potential of Discrete Cosine Transform (DCT), it is
applied on face image. A subset of coefficients of DCT from low to
mid frequencies that represent the face adequately and provides best
recognition results is retained. A tradeoff between decimation factor,
number of DCT coefficients retained and recognition rate with
minimum computation is obtained. Preprocessing of the image is
carried out to increase its robustness against variations in poses and
illumination level. This new model has been tested on different
databases which include ORL , Yale and EME color database.
Abstract: In this paper in consideration of each available
techniques deficiencies for speech recognition, an advanced method
is presented that-s able to classify speech signals with the high
accuracy (98%) at the minimum time. In the presented method, first,
the recorded signal is preprocessed that this section includes
denoising with Mels Frequency Cepstral Analysis and feature
extraction using discrete wavelet transform (DWT) coefficients; Then
these features are fed to Multilayer Perceptron (MLP) network for
classification. Finally, after training of neural network effective
features are selected with UTA algorithm.
Abstract: This paper presents features that characterize power
quality disturbances from recorded voltage waveforms using wavelet
transform. The discrete wavelet transform has been used to detect
and analyze power quality disturbances. The disturbances of interest
include sag, swell, outage and transient. A power system network has
been simulated by Electromagnetic Transients Program. Voltage
waveforms at strategic points have been obtained for analysis, which
includes different power quality disturbances. Then wavelet has been
chosen to perform feature extraction. The outputs of the feature
extraction are the wavelet coefficients representing the power quality
disturbance signal. Wavelet coefficients at different levels reveal the
time localizing information about the variation of the signal.
Abstract: The paper proposes a way of parallel processing of
SURF and Optical Flow for moving object recognition and tracking.
The object recognition and tracking is one of the most important task
in computer vision, however disadvantage are many operations cause
processing speed slower so that it can-t do real-time object recognition
and tracking. The proposed method uses a typical way of feature
extraction SURF and moving object Optical Flow for reduce
disadvantage and real-time moving object recognition and tracking,
and parallel processing techniques for speed improvement. First
analyse that an image from DB and acquired through the camera using
SURF for compared to the same object recognition then set ROI
(Region of Interest) for tracking movement of feature points using
Optical Flow. Secondly, using Multi-Thread is for improved
processing speed and recognition by parallel processing. Finally,
performance is evaluated and verified efficiency of algorithm
throughout the experiment.