Abstract: In this study, a nickel film with nano-crystalline grains,
high hardness and smooth surface was electrodeposited using a post
supercritical carbon dioxide (CO2) mixed Watts electrolyte. Although
the hardness was not as high as its Sc-CO2 counterpart, the thin coating
contained significantly less number of nano-sized pinholes. By
measuring the escape concentration of the dissolved CO2 in post
Sc-CO2 mixed electrolyte with the elapsed time, it was believed that
the residue of dissolved CO2 bubbles should closely relate to the
improvement in hardness and surface roughness over its conventional
plating counterpart. Therefore, shortening the duration of
electroplating with the raise of current density up to 0.5 A/cm2 could
effectively retain more post Sc-CO2 mixing effect. This study not only
confirms the roles of dissolved CO2 bubbles in electrolyte but also
provides a potential process to overcome most issues associated with
the cost in building high-pressure chamber for large size products and
continuous plating using supercritical method.
Abstract: The intention of this study to design the probability optimized sewing sack-s workstation based on ergonomics for productivity improvement and decreasing musculoskeletal disorders. The physical dimensions of two workers were using to design the new workstation. The physical dimensions are (1) sitting height, (2) mid shoulder height sitting, (3) shoulder breadth, (4) knee height, (5) popliteal height, (6) hip breadth and (7) buttock-knee length. The 5th percentile of buttock knee length sitting (51 cm), the 50th percentile of mid shoulder height sitting (62 cm) and the 95th percentile of popliteal height (43 cm) and hip breadth (45 cm) applied to design the workstation for sewing sack-s operator and the others used to adjust the components of this workstation. The risk assessment by RULA before and after using the probability optimized workstation were 7 and 7 scores and REBA scores were 11 and 5, respectively. Body discomfort-abnormal index was used to assess muscle fatigue of operators before adjustment workstation found that neck muscles, arm muscles area, muscles on the back and the lower back muscles fatigue. Therefore, the extension and flexion exercise was applied to relief musculoskeletal stresses. The workers exercised 15 minutes before the beginning and the end of work for 5 days. After that, the capability of flexion and extension muscles- workers were increasing in 3 muscles (arm, leg, and back muscles).
Abstract: Fire disaster is the major factor to endanger the public
and environmental safety. People lost their life during fire disaster
mainly be attributed to the dense smoke and toxic gas under
combustion, which hinder the escape of people and the rescue of
firefighters under fire disaster. The smoke suppression effect of
several transitional metals oxide on the epoxy resin treated with
intumescent flame retardant and titanate couple agent
(EP/IFR/Titanate) system have been investigated. The results showed
manganese dioxide has great effect on reducing the smoke density rate
(SDR) of EP/IFR/Titanate system; however it has little effect to reduce
the maximum smoke density (MSD) of EP/IFR/Titanate system.
Copper oxide can decrease the maximum smoke density (MSD) and
smoke density rate of EP/IFR/Titanate system substantially. The MSD
and SDR of EP/IFR/Titanate system can reduce 20.3% and 39.1%
respectively when 2% of copper oxide is introduced.
Abstract: Due to today-s turbulent environment, manufacturing resources, particularly in assembly, must be reconfigured frequently. These reconfigurations are caused by various, partly cyclic, influencing factors. Hence, it is important to evaluate the innovation ability - the capability of resources to implement innovations quickly and efficiently without large expense - of manufacturing resources. For this purpose, a new methodology is presented in this article. Within the methodology, design structure matrices and graph theory are used. The results of the methodology include different indices to evaluate the innovation ability of the manufacturing resources. Due to the cyclicity of the influencing factors, the methodology can be used to synchronize the realization of adaptations.
Abstract: Omni directional mobile robots have been popularly
employed in several applications especially in soccer player robots
considered in Robocup competitions. However, Omni directional
navigation system, Omni-vision system and solenoid kicking
mechanism in such mobile robots have not ever been combined. This
situation brings the idea of a robot with no head direction into
existence, a comprehensive Omni directional mobile robot. Such a
robot can respond more quickly and it would be capable for more
sophisticated behaviors with multi-sensor data fusion algorithm for
global localization base on the data fusion. This paper has tried to
focus on the research improvements in the mechanical, electrical and
software design of the robots of team ADRO Iran. The main
improvements are the world model, the new strategy framework,
mechanical structure, Omni-vision sensor for object detection, robot
path planning, active ball handling mechanism and the new kicker
design, , and other subjects related to mobile robot
Abstract: This paper presents a model of case based corporate
memory named ReCaRo (REsource, CAse, ROle). The approach
suggested in ReCaRo decomposes the domain to model through a set
of components. These components represent the objects developed by
the company during its activity. They are reused, and sometimes,
while bringing adaptations. These components are enriched by
knowledge after each reuse. ReCaRo builds the corporate memory on
the basis of these components. It models two types of knowledge: 1)
Business Knowledge, which constitutes the main knowledge capital
of the company, refers to its basic skill, thus, directly to the
components and 2) the Experience Knowledge which is a specialised
knowledge and represents the experience gained during the handling
of business knowledge. ReCaRo builds corporate memories which
are made up of five communicating ones.
Abstract: Optimizing equipment selection in heavy earthwork
operations is a critical key in the success of any construction project.
The objective of this research incentive was geared towards
developing a computer model to assist contractors and construction
managers in estimating the cost of heavy earthwork operations.
Economical operation analysis was conducted for an equipment fleet
taking into consideration the owning and operating costs involved in
earthwork operations. The model is being developed in a Microsoft
environment and is capable of being integrated with other estimating
and optimization models. In this study, Caterpillar® Performance
Handbook [5] was the main resource used to obtain specifications of
selected equipment. The implementation of the model shall give
optimum selection of equipment fleet not only based on cost
effectiveness but also in terms of versatility. To validate the model, a
case study of an actual dam construction project was selected to
quantify its degree of accuracy.
Abstract: The presence of a vertical fatigue crack in the web of
a plate girder subjected to pure bending influences the bending
moment capacity of the girder. The growth of the crack may lead to
premature elastic failure due to flange local yielding, flange local
buckling, or web local buckling. Approximate expressions for the
bending moment capacities corresponding to these failure modes
were formulated. Finite element analyses were then used to validate
the expressions. The expressions were employed to assess the effects
of crack length on the capacity. Neglecting brittle fracture, tension
buckling, and ductile failure modes, it was found that typical girders
are governed by the capacity associated with flange local yielding as
influenced by the crack. Concluding, a possible use of the capacity
expressions in girder design was demonstrated.
Abstract: This paper tests the level of market integration between Malaysia and Singapore stock markets with the world market. Kalman Filter (KF) methodology is used on the International Capital Asset Pricing Model (ICAPM) and the pricing errors estimated within the framework of ICAPM are used as a measure of market integration or segmentation. The advantage of the KF technique is that it allows for time-varying coefficients in estimating ICAPM and hence able to capture the varying degree of market integration. Empirical results show clear evidence of varying degree of market integration for both case of Malaysia and Singapore. Furthermore, the results show that the changes in the level of market integration are found to coincide with certain economic events that have taken placed. The findings certainly provide evidence on the practicability of the KF technique to estimate stock markets integration. In the comparison between Malaysia and Singapore stock market, the result shows that the trends of the market integration indices for Malaysia and Singapore look similar through time but the magnitude is notably different with the Malaysia stock market showing greater degree of market integration. Finally, significant evidence of varying degree of market integration shows the inappropriate use of OLS in estimating the level of market integration.
Abstract: In the LFC problem, the interconnections among some areas are the input of disturbances, and therefore, it is important to suppress the disturbances by the coordination of governor systems. In contrast, tie-line power flow control by TCPS located between two areas makes it possible to stabilize the system frequency oscillations positively through interconnection, which is also expected to provide a new ancillary service for the further power systems. Thus, a control strategy using controlling the phase angle of TCPS is proposed for provide active control facility of system frequency in this paper. Also, the optimum adjustment of PID controller's parameters in a robust way under bilateral contracted scenario following the large step load demands and disturbances with and without TCPS are investigated by Particle Swarm Optimization (PSO), that has a strong ability to find the most optimistic results. This newly developed control strategy combines the advantage of PSO and TCPS and has simple stricture that is easy to implement and tune. To demonstrate the effectiveness of the proposed control strategy a three-area restructured power system is considered as a test system under different operating conditions and system nonlinearities. Analysis reveals that the TCPS is quite capable of suppressing the frequency and tie-line power oscillations effectively as compared to that obtained without TCPS for a wide range of plant parameter changes, area load demands and disturbances even in the presence of system nonlinearities.
Abstract: This paper presents the development of low cost Nano membrane fabrication system. The system is specially designed for anodic aluminum oxide membrane. This system is capable to perform the processes such as anodization and electro-polishing. The designed machine was successfully tested for 'mild anodization' (MA) for 48 hours and 'hard anodization' (HA) for 3 hours at constant 0oC. The system is digitally controlled and guided for temperature maintenance during anodization and electro-polishing. The total cost of the developed machine is 20 times less than the multi-cooling systems available in the market which are generally used for this purpose.
Abstract: This research study the application of the immobilized
TiO2 layer and Cu-TiO2 layer on graphite substrate as a negative
electrode or anode for Li-ion battery. The titania layer was produced
through chemical bath deposition method, meanwhile Cu particles
were deposited electrochemically. A material can be used as an
electrode as it has capability to intercalates Li ions into its crystal
structure. The Li intercalation into TiO2/Graphite and Cu-
TiO2/Graphite were analyzed from the changes of its XRD pattern
after it was used as electrode during discharging process. The XRD
patterns were refined by Le Bail method in order to determine the
crystal structure of the prepared materials. A specific capacity and the
cycle ability measurement were carried out to study the performance
of the prepared materials as negative electrode of the Li-ion battery.
The specific capacity was measured during discharging process from
fully charged until the cut off voltage. A 300 was used as a load.
The result shows that the specific capacity of Li-ion battery with
TiO2/Graphite as negative electrode is 230.87 ± 1.70mAh.g-1 which is
higher than the specific capacity of Li-ion battery with pure graphite
as negative electrode, i.e 140.75 ±0.46mAh.g-1. Meanwhile
deposition of Cu onto TiO2 layer does not increase the specific
capacity, and the value even lower than the battery with
TiO2/Graphite as electrode. The cycle ability of the prepared battery
is only two cycles, due to the Li ribbon which was used as cathode
became fragile and easily broken.
Abstract: The deficit of power for electricity demand reaches
almost 30% for consumers in the last few years. This reflects with
continually increasing the price of electricity, and today the price for
small industry is almost 110Euro/MWh. The high price is additional
problem for the owners in the economy crisis which is reflected with
higher price of the goods.
The paper gives analyses of the energy needs for real agro
complex in Macedonia, private vinery with capacity of over 2 million
liters in a year and with self grapes and fruits fields. The existing
power supply is from grid with 10/04 kV transformer. The
geographical and meteorological condition of the vinery location
gives opportunity for including renewable as a power supply option
for the vinery complex.
After observation of the monthly energy needs for the vinery, the
base scenario is the existing power supply from the distribution grid.
The electricity bill in small industry has three factors: electricity in
high and low tariffs in kWh and the power engaged for the
technological process of production in kW. These three factors make
the total electricity bill and it is over 110 Euro/MWh which is the
price near competitive for renewable option. On the other side
investments in renewable (especially photovoltaic (PV)) has tendency
of decreasing with price of near 1,5 Euro/W. This means that
renewable with PV can be real option for power supply for small
industry capacities (under 500kW installed power).
Therefore, the other scenarios give the option with PV and the last
one includes wind option. The paper presents some scenarios for
power supply of the vinery as the followings:
• Base scenario of existing conventional power supply from the
grid
• Scenario with implementation of renewable of Photovoltaic
• Scenario with implementation of renewable of Photovoltaic and
Wind power
The total power installed in a vinery is near 570 kW, but the
maximum needs are around 250kW. At the end of the full paper some
of the results from scenarios will be presented. The paper also
includes the environmental impacts of the renewable scenarios, as
well as financial needs for investments and revenues from renewable.
Abstract: Theory of Constraints has been emerging as an
important tool for optimization of manufacturing/service systems.
Goldratt in his first book “ The Goal " gave the introduction on
Theory of Constraints and its applications in a factory scenario. A
large number of production managers around the globe read this book
but only a few could implement it in their plants because the book did
not explain the steps to implement TOC in the factory. To overcome
these limitations, Goldratt wrote this book to explain TOC, DBR and
the method to implement it. In this paper, an attempt has been made
to summarize the salient features of TOC and DBR listed in the book
and the correct approach to implement TOC in a factory setting. The
simulator available along with the book was actually used by the
authors and the claim of Goldratt regarding the use of DBR and
Buffer management to ease the work of production managers was
tested and was found to be correct.
Abstract: Continuously growing needs for Internet applications
that transmit massive amount of data have led to the emergence of
high speed network. Data transfer must take place without any
congestion and hence feedback parameters must be transferred from
the receiver end to the sender end so as to restrict the sending rate in
order to avoid congestion. Even though TCP tries to avoid
congestion by restricting the sending rate and window size, it never
announces the sender about the capacity of the data to be sent and
also it reduces the window size by half at the time of congestion
therefore resulting in the decrease of throughput, low utilization of
the bandwidth and maximum delay. In this paper, XCP protocol is
used and feedback parameters are calculated based on arrival rate,
service rate, traffic rate and queue size and hence the receiver
informs the sender about the throughput, capacity of the data to be
sent and window size adjustment, resulting in no drastic decrease in
window size, better increase in sending rate because of which there is
a continuous flow of data without congestion. Therefore as a result of
this, there is a maximum increase in throughput, high utilization of
the bandwidth and minimum delay. The result of the proposed work
is presented as a graph based on throughput, delay and window size.
Thus in this paper, XCP protocol is well illustrated and the various
parameters are thoroughly analyzed and adequately presented.
Abstract: In this paper, we focus on the fusion of images from
different sources using multiresolution wavelet transforms. Based on
reviews of popular image fusion techniques used in data analysis,
different pixel and energy based methods are experimented. A novel
architecture with a hybrid algorithm is proposed which applies pixel
based maximum selection rule to low frequency approximations and
filter mask based fusion to high frequency details of wavelet
decomposition. The key feature of hybrid architecture is the
combination of advantages of pixel and region based fusion in a
single image which can help the development of sophisticated
algorithms enhancing the edges and structural details. A Graphical
User Interface is developed for image fusion to make the research
outcomes available to the end user. To utilize GUI capabilities for
medical, industrial and commercial activities without MATLAB
installation, a standalone executable application is also developed
using Matlab Compiler Runtime.
Abstract: Imprecision is a long-standing problem in CAD design
and high accuracy image-based reconstruction applications. The visual
hull which is the closed silhouette equivalent shape of the objects
of interest is an important concept in image-based reconstruction.
We extend the domain-theoretic framework, which is a robust and
imprecision capturing geometric model, to analyze the imprecision in
the output shape when the input vertices are given with imprecision.
Under this framework, we show an efficient algorithm to generate the
2D partial visual hull which represents the exact information of the
visual hull with only basic imprecision assumptions. We also show
how the visual hull from polyhedra problem can be efficiently solved
in the context of imprecise input.
Abstract: A linear feedback shift register (LFSR) is proposed which targets to reduce the power consumption from within. It reduces the power consumption during testing of a Circuit Under Test (CUT) at two stages. At first stage,
Control Logic (CL) makes the clocks of the switching units
of the register inactive for a time period when output from
them is going to be same as previous one and thus reducing
unnecessary switching of the flip-flops. And at second stage,
the LFSR reorders the test vectors by interchanging the bit
with its next and closest neighbor bit. It keeps fault coverage
capacity of the vectors unchanged but reduces the Total Hamming Distance (THD) so that there is reduction in power
while shifting operation.
Abstract: The connection between solar activity and adverse phenomena in the Earth’s environment that can affect space and ground based technologies has spurred interest in Space Weather (SW) research. A great effort has been put on the development of suitable models that can provide advanced forecast of SW events. With the progress in computational technology, it is becoming possible to develop operational large scale physics based models which can incorporate the most important physical processes and domains of the Sun-Earth system. In order to enhance our SW prediction capabilities we are developing advanced numerical tools. With operational requirements in mind, our goal is to develop a modular simulation framework of propagation of the disturbances from the Sun through interplanetary space to the Earth. Here, we report and discuss on the development of coronal field and solar wind components for a large scale MHD code. The model for these components is based on a potential field source surface model and an empirical Wang-Sheeley-Arge solar wind relation.
Abstract: Thisresearch paper is dedicated to an actual issue in Latvia and in the whole European Union – development of the secondary materials management. The goal of this paper is to research the development of the secondary materials management in Latvia as a result to point out its main positive aspects and problems. In this research paper the author regards following issues: significance of the secondary materials management, current situation of the waste generation and utilization in Latvia comparing with other EU Member States, main problems and positive aspects of the secondary materials management in Latvia. The research author concludes that in last ten years a great work is done to develop the secondary materials market. Nevertheless following improvements are necessary: implementation of the packaging deposit system, development of the separate waste collection, increasing of the recycling capacity.